The effect of metal transfer stability (spattering) on fume generation, morphology and composition in short-circuit MAG welding

The main objective of this work was to evaluate the hypothesis that the greater transfer stability leads also to less volume of fumes. Using an Ar + 25%CO2 blend as shielding gas and maintaining constant the average current, wire feed speed and welding speed, bead-on-plate welds were carried out with plain carbon steel solid wire. The welding voltage was scanned to progressively vary the transfer stability. Using two conditions of low stability and one with high stability, fume generation was evaluated by means of the AWS F1.2:2006 standard. The influence of these conditions on fume morphology and composition was also verified. A condition with greater transfer stability does not generate less fume quantity, despite the fact that this condition produces fewer spatters. Other factors such as short-circuit current, arcing time, droplet diameters and arc length are the likely governing factors, but in an interrelated way. Metal transfer stability does not influence either the composition or the size/morphology of fume particulates. (c) 2014 Elsevier B.V. All rights reserved.

Kaarityypin ja suojakaasun vaikutus roiskeisuuteen teräksen MAG-hitsauksessa

Tässä kandidaatintyössä tutkitaan suojakaasun ja kaarityypin vaikutuksia roiskeisuuden muodostumiselle teräksen MAG-hitsauksessa (nro. 135). Roiskeisuuden tutkimisessa tutkitaan kolmea (3) eri kaarityyppiä ja kahta (2) eri suojakaasua ja niiden keskenäisiä vaikutuksia roiskeiden syntymiselle. Tutkittavat kaarityypit ovat pulssi-, kuumakaari sekä Kemppi Oy:n WiseFusion erikoiskaarisovellus. Suojakaasuina käyetään AGAn Corgon 3 ja Mison 18 suojakaasuja. Hitsauskokeita suoritetaan kuusi (6) kappaletta alapienana jalkoasennossa (PA). Työn alussa perehdytään MAG-hitsauksen laitteistoon ja teoriaan sekä perehdytään mitkä eri asiat vaikuttavat roiskeiden muodostumiseen. Työn lopussa verrataan tieteellisistä julkaisuista löydettyjä tietoja ja tuloksia itsetehtyihin koetuloksiin.

Optical Characterization and Optimization of Display Components : Some Applications to Liquid-Crystal-Based and Electrochromics-Based Devices

This dissertation is focused on theoretical and experimental studies of optical properties of materials and multilayer structures composing liquid crystal displays (LCDs) and electrochromic (EC) devices. By applying spectroscopic ellipsometry, we have determined the optical constants of thin films of electrochromic tungsten oxide (WOx) and nickel oxide (NiOy), the films’ thickness and roughness. These films, which were obtained at spattering conditions possess high transmittance that is important for achieving good visibility and high contrast in an EC device. Another application of the general spectroscopic ellipsometry relates to the study of a photo-alignment layer of a mixture of azo-dyes SD-1 and SDA-2. We have found the optical constants of this mixture before and after illuminating it by polarized UV light. The results obtained confirm the diffusion model to explain the formation of the photo-induced order in azo-dye films. We have developed new techniques for fast characterization of twisted nematic LC cells in transmissive and reflective modes. Our techniques are based on the characteristics functions that we have introduced for determination of parameters of non-uniform birefringent media. These characteristic functions are found by simple procedures and can be utilised for simultaneous determination of retardation, its wavelength dispersion, and twist angle, as well as for solving associated optimization problems. Cholesteric LCD that possesses some unique properties, such as bistability and good selective scattering, however, has a disadvantage – relatively high driving voltage (tens of volts). The way we propose to reduce the driving voltage consists of applying a stack of thin (~1µm) LC layers. We have studied the ability of a layer of a surface stabilized ferroelectric liquid crystal coupled with several retardation plates for birefringent color generation. We have demonstrated that in order to accomplish good color characteristics and high brightness of the display, one or two retardation plates are sufficient.

Size distributions of fine silicate and other particles in Masaya's volcanic plume

Direct-sampling and remote-sensing measurements were made at the crater rim of Masaya volcano (Nicaragua) to sample the aerosol plume emanating from the active vent. We report the first measurements of the size distribution of fine silicate particles (d <10 mu m) in Masaya's plume, by automated scanning electron microscopy (QEMSCAN) analysis of a particle filter. The particle size distribution was approximately lognormal with modal d similar to 1.15 mu m. The majority of these particles were found to be spherical. These particles are interpreted to be droplets of quenched magma produced by a spattering process. Compositional analyses confirm earlier reports that the fine silicate particles show a range of compositions between that of the degassing magma and nearly pure silica and that the extent of compositional variability decreases with increasing particle size. These results indicate that fine silicate particles are altered owing to reactions with acidic droplets in the plume. The emission flux of fine silicate particles was estimated as similar to 10(11) s(-1), equivalent to similar to 55 kg d(-1). Sun photometry, aerosol spectrometry, and thermal precipitation were used to determine the overall particle size distribution of the plume (0.01 < d(mu m) < 10). Sun photometry and aerosol spectrometry measurements indicate the presence of a large number of particles (assumed to be aqueous) with d similar to 1 mu m. Aerosol spectrometry measurements further show an increase in particle size as the nighttime approached. The emission flux of particles from Masaya was estimated as similar to 10(17) s(-1), equivalent to similar to 5.5 Mg d(-1) where d < 4 mu m.

„Pulverbettbasiertes Strahlschmelzen – neue Forschungserkenntnisse“

Auf dem Weg vom Rapid Prototyping zum Rapid Manufacturing ist erhöhte Prozesssicherheit sowie die Beherrschung verfahrensspezifischer Phänomene notwendig, um die immer weiter steigenden und konkreteren Bauteilanforderungen zu erfüllen. Dazu wurden diverse im SLM-Prozess auftretende Effekte untersucht. Basis der vorgestellten Entwicklungen sind grundlegende Erkenntnisse zur Oberflächenqualität von SLM-Bauteilen und Einflussgrößen auf Dichte und mechanische Eigenschaften der Bauteile verschiedener Werkstoffe. Ergebnis sind verschiedene Weiterentwicklungen der Standardbelichtungsstrategie, wodurch etwa Eigenspannungseffekte und Spritzerbildung positiv beeinflusst werden können.

Metal transfer mapping for FCAW process by using near-infrared filming

In the Flux Cored Arc Welding (FCAW) process, the transfer of filler metal (metal transfer modes) to the base material to accomplish the weld bead determines the weld quality and therefore studies of such phenomena is demanded. Thus, in this work, the metal transfer through the FCAW process is investigated by filming the phenomena with the assist of near infrared visualization. During the literature survey, it was found that this technic has not been used so far for analyzing the FCAW process. It must be pointed out that the radiation emitted from the weld arc, fumes and particles (spattering) in this process represent a barrier for these studies based in the process visualization. The monitoring of metal transfer for FCAW process was carried out within the operational envelope of voltage and wire feed speed with the electrode E71T-1 (1.2 mm diameter) and Ar+25%CO2 as a shielding gas. A local developed near infrared filming with frame rate of 300 Hz was employed for metal transfer visualization in order to contribute to a better understanding of this process and evaluating characteristics of metal transfer, unlike previous studies, which used shadowgraph technique. It can clearly be seen how the droplet is created and transferred in this process and also identify the different modes of metal transfer by changing the parameters of voltage and wire feed speed in metal transfer maps. The final result of this study is the metal transfer mode maps, which establish suitable conditions and provide the basis for developing arc control strategies for the FCAW process.

Aspetti microstrutturali, proprietà meccaniche e ottimizzazione del trattamento termico di un acciaio inossidabile PH processato con laser powder bed fusion

L’attività di ricerca svolta in questa tesi ha riguardato gli aspetti microstrutturali, le proprietà meccaniche e l’ottimizzazione del trattamento termico di un acciaio inossidabile indurente per precipitazione processato mediante tecnologia additiva Laser Powder Bed Fusion (L-PBF). I provini, realizzati presso il competence center Bi-REX (Bologna) e lavorati presso il laboratorio di Metallurgia del DIN, sono stati oggetto di vari trattamenti termici sperimentali in cui è stata fatta variare la temperatura e la durata di mantenimento in forno, al fine di identificare la combinazione ottimale di temperatura e tempo sia per la fase di solubilizzazione che di invecchiamento. Nello specifico, la scelta dei parametri di solubilizzazione e invecchiamento è stata fatta solo sulla base dei trend di durezza. Da queste attività sono stati scelti i parametri di trattamento che garantissero elevata durezza, prossima alla massima ottenibile, senza durate di invecchiamento eccessive. L'esito della sperimentazione ha permesso di ridurre sensibilmente temperatura e durata di solubilizzazione rispetto al trattamento benchmark senza penalizzazione della durezza risultante. Dopodiché è stata eseguita una caratterizzazione microstrutturale e meccanica dell’acciaio, in termini di durezza, trazione e resilienza, per confrontare il trattamento termico ottimizzato con la condizione As-Built (AB) e con il trattamento termico standard indicato dal produttore. L’elevata durezza misurata dopo invecchiamento si deve alla presenza di precipitati di rinforzo in grado di ostacolare il moto delle dislocazioni. Le prove meccaniche hanno confermato l’ottenimento di elevata resistenza a snervamento e a trazione, superiore al benchmark, ma di un basso allungamento a rottura e bassissima resilienza a causa di difetti quali porosità, mancate fusioni e spattering. Infine, lo studio delle superfici di frattura ha permesso di analizzare i meccanismi di rottura dei campioni di trazione e resilienza.