Simulation of bistatic radar experiments with deep space missions

L’obiettivo del lavoro esposto nella seguente relazione di tesi ha riguardato lo studio e la simulazione di esperimenti di radar bistatico per missioni di esplorazione planeteria. In particolare, il lavoro si è concentrato sull’uso ed il miglioramento di un simulatore software già realizzato da un consorzio di aziende ed enti di ricerca nell’ambito di uno studio dell’Agenzia Spaziale Europea (European Space Agency – ESA) finanziato nel 2008, e svolto fra il 2009 e 2010. L’azienda spagnola GMV ha coordinato lo studio, al quale presero parte anche gruppi di ricerca dell’Università di Roma “Sapienza” e dell’Università di Bologna. Il lavoro svolto si è incentrato sulla determinazione della causa di alcune inconsistenze negli output relativi alla parte del simulatore, progettato in ambiente MATLAB, finalizzato alla stima delle caratteristiche della superficie di Titano, in particolare la costante dielettrica e la rugosità media della superficie, mediante un esperimento con radar bistatico in modalità downlink eseguito dalla sonda Cassini-Huygens in orbita intorno al Titano stesso. Esperimenti con radar bistatico per lo studio di corpi celesti sono presenti nella storia dell’esplorazione spaziale fin dagli anni ’60, anche se ogni volta le apparecchiature utilizzate e le fasi di missione, durante le quali questi esperimenti erano effettuati, non sono state mai appositamente progettate per lo scopo. Da qui la necessità di progettare un simulatore per studiare varie possibili modalità di esperimenti con radar bistatico in diversi tipi di missione. In una prima fase di approccio al simulatore, il lavoro si è incentrato sullo studio della documentazione in allegato al codice così da avere un’idea generale della sua struttura e funzionamento. È seguita poi una fase di studio dettagliato, determinando lo scopo di ogni linea di codice utilizzata, nonché la verifica in letteratura delle formule e dei modelli utilizzati per la determinazione di diversi parametri. In una seconda fase il lavoro ha previsto l’intervento diretto sul codice con una serie di indagini volte a determinarne la coerenza e l’attendibilità dei risultati. Ogni indagine ha previsto una diminuzione delle ipotesi semplificative imposte al modello utilizzato in modo tale da identificare con maggiore sicurezza la parte del codice responsabile dell’inesattezza degli output del simulatore. I risultati ottenuti hanno permesso la correzione di alcune parti del codice e la determinazione della principale fonte di errore sugli output, circoscrivendo l’oggetto di studio per future indagini mirate.

Space missions to comets : a conference /

Includes bibliographies.

Advanced automation for space missions : proceedings of the 1980 NASA/ASEE Summer Study /

Includes bibliographies.

Simulation of optical observables for space missions to small bodies

The navigation of deep space spacecraft requires accurate measurement of the probe’s state and attitude with respect to a body whose ephemerides may not be known with good accuracy. The heliocentric state of the spacecraft is estimated through radiometric techniques (ranging, Doppler, and Delta-DOR), while optical observables can be introduced to improve the uncertainty in the relative position and attitude with respect to the target body. In this study, we analyze how simulated optical observables affect the estimation of parameters in an orbit determination problem, considering the case of the ESA’s Hera mission towards the binary asteroid system composed of Didymos and Dimorphos. To this extent, a shape model and a photometric function are used to create synthetic onboard camera images. Then, using a stereophotoclinometry technique on some of the simulated images, we create a database of maplets that describe the 3D geometry of the surface around a set of landmarks. The matching of maplets with the simulated images provides the optical observables, expressed as pixel coordinates in the camera frame, which are fed to an orbit determination filter to estimate a certain number of solve-for parameters. The noise introduced in the output optical observables by the image processing can be quantified using as a metric the quality of the residuals, which is used to fine-tune the maplet-matching parameters. In particular, the best results are obtained when using small maplets, with high correlation coefficients and occupation factors.

Definition, realization and evaluation of a software reference architecture for use in space applications

A recent initiative of the European Space Agency (ESA) aims at the definition and adoption of a software reference architecture for use in on-board software of future space missions. Our PhD project placed in the context of that effort. At the outset of our work we gathered all the industrial needs relevant to ESA and all the main European space stakeholders and we were able to consolidate a set of technical high-level requirements for the fulfillment of them. The conclusion we reached from that phase confirmed that the adoption of a software reference architecture was indeed the best solution for the fulfillment of the high-level requirements. The software reference architecture we set on building rests on four constituents: (i) a component model, to design the software as a composition of individually verifiable and reusable software units; (ii) a computational model, to ensure that the architectural description of the software is statically analyzable; (iii) a programming model, to ensure that the implementation of the design entities conforms with the semantics, the assumptions and the constraints of the computational model; (iv) a conforming execution platform, to actively preserve at run time the properties asserted by static analysis. The nature, feasibility and fitness of constituents (ii), (iii) and (iv), were already proved by the author in an international project that preceded the commencement of the PhD work. The core of the PhD project was therefore centered on the design and prototype implementation of constituent (i), a component model. Our proposed component model is centered on: (i) rigorous separation of concerns, achieved with the support for design views and by careful allocation of concerns to the dedicated software entities; (ii) the support for specification and model-based analysis of extra-functional properties; (iii) the inclusion space-specific concerns.

Design and implementation of a novel multi-constellation FPGA-based dual frequency GNSS receiver for space applications

The PhD activity described in the document is part of the Microsatellite and Microsystem Laboratory of the II Faculty of Engineering, University of Bologna. The main objective is the design and development of a GNSS receiver for the orbit determination of microsatellites in low earth orbit. The development starts from the electronic design and goes up to the implementation of the navigation algorithms, covering all the aspects that are involved in this type of applications. The use of GPS receivers for orbit determination is a consolidated application used in many space missions, but the development of the new GNSS system within few years, such as the European Galileo, the Chinese COMPASS and the Russian modernized GLONASS, proposes new challenges and offers new opportunities to increase the orbit determination performances. The evaluation of improvements coming from the new systems together with the implementation of a receiver that is compatible with at least one of the new systems, are the main activities of the PhD. The activities can be divided in three section: receiver requirements definition and prototype implementation, design and analysis of the GNSS signal tracking algorithms, and design and analysis of the navigation algorithms. The receiver prototype is based on a Virtex FPGA by Xilinx, and includes a PowerPC processor. The architecture follows the software defined radio paradigm, so most of signal processing is performed in software while only what is strictly necessary is done in hardware. The tracking algorithms are implemented as a combination of Phase Locked Loop and Frequency Locked Loop for the carrier, and Delay Locked Loop with variable bandwidth for the code. The navigation algorithm is based on the extended Kalman filter and includes an accurate LEO orbit model.

Development of an X-ray spectrometric system and feasibility tests of Silicon Drift Detector for medical and space applications

The thesis work concerns X-ray spectrometry for both medical and space applications and is divided into two sections. The first section addresses an X-ray spectrometric system designed to study radiological beams and is devoted to the optimization of diagnostic procedures in medicine. A parametric semi-empirical model capable of efficiently reconstructing diagnostic X-ray spectra in 'middle power' computers was developed and tested. In addition, different silicon diode detectors were tested as real-time detectors in order to provide a real-time evaluation of the spectrum during diagnostic procedures. This project contributes to the field by presenting an improved simulation of a realistic X-ray beam emerging from a common X-ray tube with a complete and detailed spectrum that lends itself to further studies of added filtration, thus providing an optimized beam for different diagnostic applications in medicine. The second section describes the preliminary tests that have been carried out on the first version of an Application Specific Integrated Circuit (ASIC), integrated with large area position-sensitive Silicon Drift Detector (SDD) to be used on board future space missions. This technology has been developed for the ESA project: LOFT (Large Observatory for X-ray Timing), a new medium-class space mission that the European Space Agency has been assessing since February of 2011. The LOFT project was proposed as part of the Cosmic Vision Program (2015-2025).

An Integrated Transmission-Media Noise Calibration Software For Deep-Space Radio Science Experiments

The thesis describes the implementation of a calibration, format-translation and data conditioning software for radiometric tracking data of deep-space spacecraft. All of the available propagation-media noise rejection techniques available as features in the code are covered in their mathematical formulations, performance and software implementations. Some techniques are retrieved from literature and current state of the art, while other algorithms have been conceived ex novo. All of the three typical deep-space refractive environments (solar plasma, ionosphere, troposphere) are dealt with by employing specific subroutines. Specific attention has been reserved to the GNSS-based tropospheric path delay calibration subroutine, since it is the most bulky module of the software suite, in terms of both the sheer number of lines of code, and development time. The software is currently in its final stage of development and once completed will serve as a pre-processing stage for orbit determination codes. Calibration of transmission-media noise sources in radiometric observables proved to be an essential operation to be performed of radiometric data in order to meet the more and more demanding error budget requirements of modern deep-space missions. A completely autonomous and all-around propagation-media calibration software is a novelty in orbit determination, although standalone codes are currently employed by ESA and NASA. The described S/W is planned to be compatible with the current standards for tropospheric noise calibration used by both these agencies like the AMC, TSAC and ESA IFMS weather data, and it natively works with the Tracking Data Message file format (TDM) adopted by CCSDS as standard aimed to promote and simplify inter-agency collaboration.

Self-supporting CVD diamond charge state conversion surfaces for high resolution imaging of low-energy neutral atoms in space plasmas

Two polycrystalline diamond surfaces, manufactured by chemical vapour deposition (CVD) technique, are investigated regarding their applicability as charge state conversion surfaces (CS) for use in a low energy neutral atom imaging instrument in space research. The capability of the surfaces for converting neutral atoms into negative ions via surface ionisation processes was measured for hydrogen and oxygen with particle energies in the range from 100 eV to 1 keV and for angles of incidence between 6 deg and 15 deg. We observed surface charging during the surface ionisation processes for one of the CVD samples due to low electrical conductivity of the material. Measurements on the other CVD diamond sample resulted in ionisation efficiencies of ~2 % for H and up to 12 % for O. Analysis of the angular scattering revealed very narrow and almost circular scattering distributions. Comparison of the results with the data of the CS of the IBEX-Lo sensor shows that CVD diamond has great potential as CS material for future space missions.

Novel Gravity Distortion Evaluation on Large Antenna Array for Deep Space Communication

This paper presents a simple gravity evaluation model for large reflector antennas and the experimental example for a case study of one uplink array of 4x35-m antennas at X and Ka band. This model can be used to evaluate the gain reduction as a function of the maximum gravity distortion, and also to specify this at system designer level. The case study consists of one array of 35-m antennas for deep space missions. Main issues due to the gravity effect have been explored with Monte Carlo based simulation analysis.

High-brightness all semiconductor laser at 1.57 µm for space-borne lidar measurements of atmospheric carbon dioxide: device design and analysis of requirements

The availability of suitable laser sources is one of the main challenges in future space missions for accurate measurement of atmospheric CO2. The main objective of the European project BRITESPACE is to demonstrate the feasibility of an all-semiconductor laser source to be used as a space-borne laser transmitter in an Integrated Path Differential Absorption (IPDA) lidar system. We present here the proposed transmitter and system architectures, the initial device design and the results of the simulations performed in order to estimate the source requirements in terms of power, beam quality, and spectral properties to achieve the required measurement accuracy. The laser transmitter is based on two InGaAsP/InP monolithic Master Oscillator Power Amplifiers (MOPAs), providing the ON and OFF wavelengths close to the selected absorption line around 1.57 µm. Each MOPA consists of a frequency stabilized Distributed Feedback (DFB) master oscillator, a modulator section, and a tapered semiconductor amplifier optimized to maximize the optical output power. The design of the space-compliant laser module includes the beam forming optics and the thermoelectric coolers.The proposed system replaces the conventional pulsed source with a modulated continuous wave source using the Random Modulation-Continuous Wave (RM-CW) approach, allowing the designed semiconductor MOPA to be applicable in such applications. The system requirements for obtaining a CO2 retrieval accuracy of 1 ppmv and a spatial resolution of less than 10 meters have been defined. Envelope estimated of the returns indicate that the average power needed is of a few watts and that the main noise source is the ambient noise.

Analysis and optimization for a hexapod walking robot for planetary missions

La tecnología de las máquinas móviles autónomas ha sido objeto de una gran investigación y desarrollo en las últimas décadas. En muchas actividades y entornos, los robots pueden realizar operaciones que son duras, peligrosas o simplemente imposibles para los humanos. La exploración planetaria es un buen ejemplo de un entorno donde los robots son necesarios para realizar las tareas requeridas por los científicos. La reciente exploración de Marte con robots autónomos nos ha mostrado la capacidad de las nuevas tecnologías. Desde la invención de la rueda, que esta acertadamente considerado como el mayor invento en la historia del transporte humano, casi todos los vehículos para exploración planetaria han empleado las ruedas para su desplazamiento. Las nuevas misiones planetarias demandan maquinas cada vez mas complejas. En esta Tesis se propone un nuevo diseño de un robot con patas o maquina andante que ofrecerá claras ventajas en entornos extremos. Se demostrara que puede desplazarse en los terrenos donde los robots con ruedas son ineficientes, convirtiéndolo en una elección perfecta para misiones planetarias. Se presenta una reseña histórica de los principales misiones espaciales, en particular aquellos dirigidos a la exploración planetaria. A través de este estudio será posible analizar las desventajas de los robots con ruedas utilizados en misiones anteriores. El diseño propuesto de robot con patas será presentado como una alternativa para aquellas misiones donde los robots con ruedas puedan no ser la mejor opción. En esta tesis se presenta el diseño mecánico de un robot de seis patas capaz de soportar las grandes fuerzas y momentos derivadas del movimiento de avance. Una vez concluido el diseño mecánico es necesario realizar un análisis que permita entender el movimiento y comportamiento de una maquina de esta complejidad. Las ecuaciones de movimiento del robot serán validadas por dos métodos: cinemático y dinámico. Dos códigos Matlab® han sido desarrollados para resolver dichos sistemas de ecuaciones y han sido verificados por un tercer método, un modelo de elementos finitos, que también verifica el diseño mecánico. El robot con patas presentado, ha sido diseñado para la exploración planetaria en Marte. El comportamiento del robot durante sus desplazamientos será probado mediante un código de Matlab®, desarrollado para esta tesis, que permite modificar las trayectorias, el tipo de terreno, y el número y altura de los obstáculos. Estos terrenos y requisitos iniciales no han sido elegidos de forma aleatoria, si no que están basados en mi experiencia como miembro del equipo de MSL-NASA que opera un instrumento a bordo del rover Curiosity en Marte. El robot con patas desarrollado y fabricado por el Centro de Astrobiología (INTA-CSIC), esta basado en el diseño mecánico y análisis presentados en esta tesis. ABSTRACT The autonomous machines technology has undergone a major research and development during the last decades. In many activities and environments, robots can perform operations that are tought, dangerous or simply imposible to humans. Planetary exploration is a good example of such environment where robots are needed to perform the tasks required by the scientits. Recent Mars exploration based on autonomous vehicles has shown us the capacity of the new technologies. From the invention of the wheel, which is rightly regarded as the greatest invention in the history of human transportation, nearly all-planetary vehicles are based in wheeled locomotion, but new missions demand new types of machines due to the complex tasks needed to be performed. It will be proposed in this thesis a new design of a legged robot or walking machine, which may offer clear advantages in tough environments. This Thesis will show that the proposed walking machine can travel, were terrain difficulties make wheeled vehicles ineffective, making it a perfect choice for planetary mission. A historical background of the main space missions, in particular those aimed at planetary exploration will be presented. From this study the disadvantages found in the existing wheel rovers will be analysed. The legged robot designed will be introduced as an alternative were wheeled rovers could be no longer the best option for planetary exploration. This thesis introduces the mechanical design of a six-leg robot capable of withstanding high forces and moments due to the walking motion. Once the mechanical design is concluded, and in order to analyse a machine of this complexity an understanding of its movement and behaviour is mandatory. This movement equation will be validated by two methods: kinematics and dynamics. Two Matlab® codes have been developed to solve the systems of equations and validated by a third method, a finite element model, which also verifies the mechanical design. The legged robot presented has been designed for a Mars planetary exploration. The movement behaviour of the robot will be tested in a Matlab® code developed that allows to modify the trajectories, the type of terrain, number and height of obstacles. These terrains and initial requirements have not been chosen randomly, those are based on my experience as a member of the MSL NASA team, which operates an instrument on-board of the Curiosity rover in Mars. The walking robot developed and manufactured by the Center of Astrobiology (CAB) is based in the mechanical design and analysis that will be presented in this thesis.

Deep space orbit determination and guidance of the LICIACube microsatellite mission

Recently, the JPL's MarCO mission demonstrated that these probes are also mature enough to be employed in the deep space, even though with the limitations related to the employed commercial components. Currently, other deep space CubeSats are planned either as stand-alone missions or as companions of a traditional large probe. Therefore, developing a dedicated navigation suite is crucial to reaching the mission's goals, considering the limitations of the onboard components compared to typical deep space missions. In this framework, the LICIACube mission represents an ideal candidate test-bench, as it performs a flyby of the Didymos asteroid system subject to a strong position, epochs, and pointing requirements. This mission will also allow us to infer the capabilities of such microsatellites and highlight their limitations compared with the benefits of a lighter design and tailoring efforts. In this work, the OD and guidance methods and tools adopted for classical deep space missions have been tailored for the CubeSat applications and validated through extensive analyses. In addition, navigation procedures and interfaces have been designed in view of the operations foreseen in late 2022. The pre-launch covariance analysis has been performed to assess the mission's feasibility for the nominal trajectory and its associated uncertainties, based on conservative assumptions on the main parameters. Extensive sensitivity analyses have been carried out to understand the main mission parameters affecting the performance and to demonstrate the robustness of the designed trajectory and operation schedule in fulfilling the mission requirements. The developed system was also stressed by tuning the models to access different reconstruction methods for the maneuvers. The analysis demonstrated the feasibility of the LICIACube mission navigation in compliance with the mission requirements, compatible with the limited resources available, both in space and on the ground.

Data fusion with computational intelligence techniques: a case study of fuzzy inference for terrain assessment

Dissertação apresentada para obtenção do Grau de Mestre em Engenharia Electrotécnica e de Computadores, pela Universidade Nova de Lisboa, Faculdade de Ciências e Tecnologia

Monitoring energy consumption in android applications

Dissertação de Mestrado em Engenharia Informática