Mechanical properties of concrete produced with a composite of water treatment sludge and sawdust

In developing countries such as Brazil, the wastes generated in the decanters and filters of water treatment plants are discharged directly into the same rivers and streams that supply water for treatment. Another environmental problem is the unregulated discard of wood wastes. The lumber and wood products industry generates large quantities of this waste, from logging to the manufacture of the end product. Brazil has few biomass plants and therefore only a minor part of these wastes are reused. This paper presents the results of the first study involving a novel scientific and technological approach to evaluate the possibility of combining these two types of wastes in the production of a light-weight composite for concrete. The concrete produced with cement:sand:composite:water mass ratios of 1:2.5:0.67:0.6 displayed an axial compressive strength of 11.1 MPa, a compressive and diametral tensile strength of 1.2 MPa, water absorption of 8.8%, and a specific mass of 1.847 kg/m(3). The mechanical properties obtained with this concrete render it suitable for application in non-structural elements. (C) 2010 Elsevier Ltd. All rights reserved.

Characterization of wood biochar and evaluation of its adsorption potential for removal of sulphate from produced water in offshore oil and gas industry

This thesis analyses the potential of wood biochar as an adsorbent in removal of sulphate from produced water. In worldwide offshore oil and gas industry, a large volume of waste water is generated as produced water. Sulphur compounds present in these produced water streams can cause environmental problems, regulatory problems and operational issues. Among the various sulphur removal technologies, the adsorption technique is considered as a suitable method since the design is simple, compact, economical and robust. Biochar has been studied as an adsorbent for removal of contaminants from water in a number of studies due to its low cost, potential availability, and adsorptive characteristics. In this study, biochar produced through fast pyrolysis of bark, hardwood sawdust, and softwood sawdust were characterized through a series of tests and were analysed for adsorbent properties. Treating produced water using biochar sourced from wood waste is a two-fold solution to environmental problems as it reduces the volume of these wastes. Batch adsorption tests were carried out to obtain adsorption capacities of each biochar sample using sodium sulphate solutions. The highest sulphur adsorption capacities obtained for hardwood char, softwood char and bark char were 11.81 mg/g, 9.44 mg/g, and 7.94 mg/g respectively at 10 °C and pH=4. The adsorption process followed the second order kinetic model and the Freundlich isotherm model. Adsorption reaction was thermodynamically favourable and exothermic. The overall analysis concludes that the wood biochar is a feasible, economical, and environmental adsorbent for removal of sulphate from produced water.

On the potential utilisation of sawdust and wood chip screenings

This work is based on the utilisation of sawdust and wood chip screenings for different purposes. A substantial amount of these byproducts are readily available in the Finnish forest industry. A black liquor impregnation study showed that sawdust-like wood material behaves differently from normal chips. Furthermore, the fractionation and removal of the smallest size fractions did not have a significant effect on the impregnation of sawdust-like wood material. Sawdust kraft cooking equipped with an impregnation stage increases the cooking yield and decreases the lignin content of the produced pulp. Impregnation also increases viscosity of the pulp and decreases chlorine dioxide consumption in bleaching. In addition, impregnation increases certain pulp properties after refining. Hydrotropic extraction showed that more lignin can be extracted from hardwood than softwood. However, the particle size had a major influence on the lignin extraction. It was possible to extract more lignin from spruce sawdust than spruce chips. Wood chip screenings are usually combusted to generate energy. They can also be used in the production of kraft pulp, ethanol and chemicals. It is not economical to produce ethanol from wood chip screenings because of the expensive wood material. Instead, they should be used for production of steam and energy, kraft pulp and higher value added chemicals. Bleached sawdust kraft pulp can be used to replace softwood kraft pulp in mechanical pulp based papers because it can improve certain physical properties. It is economically more feasible to use bleached sawdust kraft pulp in stead of softwood kraft pulp, especially when the reinforcement power requirement is moderate.

Lightweight composite concrete produced with water treatment sludge and sawdust: Thermal properties and potential application

The main objective of this study was to evaluate the potential application of a lightweight concrete produced with lightweight coarse aggregate made of the water treatment sludge and sawdust (lightweight composite), by determining the thermal properties and possible environmental impact of future residue of this concrete. Two types of concrete were prepared: concrete produced with the lightweight composite dosed with cement/sand/composite/water in a mass ratio of 1:2.5:0.67:0.6 and conventional concrete dosed with cement/sand/crushed stone/water in a mass ratio of 1:4.8:5.8:0.8. The thermal properties were determined by the hot wire parallel technique. The possible environmental impact was measured using the procedures and guidelines of the Brazilian Association of Technical Standards - ABNT. The concrete produced with the lightweight composite presented a 23% lower thermal conductivity than the conventional concrete. The concrete produced with the lightweight composite presented a set of thermal properties suitable for the application of this concrete in non-structural sealing elements. The concentration of aluminum in the solubilized extract of the concrete produced with the lightweight composite was much lower than the concentration of aluminum in the water treatment sludge, confirming the possible reduction of environmental impact of this composite for use in concrete. (C) 2010 Elsevier Ltd. All rights reserved.

NMR imaging of fluid pathways during drainage of softwood in a pressure membrane chamber

An experiment was implemented to study fluid flow in a pressure media. This procedure successfully combines nuclear magnetic resonance imaging with a pressure membrane chamber in order to visualize the non-wetting and wetting fluid flows with controlled boundary conditions. A specially designed pressure membrane chamber, made of non-magnetic materials and able to withstand 4 MPa, was designed and built for this purpose. These two techniques were applied to the drainage of Douglas fir sapwood. In the study of the longitudinal flow, narrow drainage fingers are formed in the latewood zones. They follow the longitudinal direction of wood and spread throughout the sample length. These fingers then enlarge in the cross-section plane and coalesce until drainage reaches the whole latewood part. At the end of the experiments, when the drainage of liquid water in latewood is completed, just a few sites of percolation appear in earlywood zones. This difference is a result of the wood anatomical structure, where pits, the apertures that allow the sap to flow between wood cells, are more easily aspirated in earlywood than in latewood. (C) 2007 Elsevier Ltd. All rights reserved.

Adsorption kinetics for the removal of chromium(VI) from aqueous solution by adsorbents derived from used tyres and sawdust

The batch removal of hexavalent chromium (Cr(Vl)) from wastewater under different experimental conditions using economic adsorbents was investigated in this study. These adsorbents were produced from the pyrolysis and activation of the waste tyres (TAC) and from the pyrolysis of sawdust (SPC). The performance of these adsorbents against commercial activated carbon F400 (CAC) has also been carried out. The removal was favoured at low pH, with maximum removal at pH = 2 for all types of carbon. The effects of concentration, temperature and particle size have been reported. All sorbents were found to efficiently remove Cr(VI) from solution. The batch sorption kinetics have been tested for a first-order reversible reaction, a first-order and second-order reaction. The rate constants of adsorption for all these kinetic models have been calculated. The applicability of the Langmuir isotherm for the present system has been tested at different temperatures. The thermodynamic parameters (AGO, K,) obtained indicate the endothermic nature of Cr(Vl) adsorption on TAC, SPC and CAC. (C) 2001 Elsevier Science B.V. All rights reserved.

Ash deposition during the co-firing of bituminous coal with pine sawdust and olive stones in a laboratory furnace

This article describes an experimental study on ash deposition during the co-firing of bituminous coal with pine sawdust and olive stones in a laboratory furnace. The main objective of this study was to relate the ash deposit rates with the type of biomass burned and its thermal percentage in the blend. The thermal percentage of biomass in the blend was varied between 10% and 50% for both sawdust and olive stones. For comparison purposes, tests have also been performed using only coal or only biomass. During the tests, deposits were collected with the aid of an air-cooled deposition probe placed far from the flame region, where the mean gas temperature was around 640 degrees C. A number of deposit samples were subsequently analyzed on a scanning electron microscope equipped with an energy dispersive X-ray detector. Results indicate that blending sawdust with coal decreases the deposition rate as compared with the firing of unblended coal due to both the sawdust low ash content and its low alkalis content. The co-firing of coal and sawdust yields deposits with high levels of silicon and aluminium which indicates the presence of ashes with high fusion temperature and, thus, with less capacity to adhere to the surfaces. In contrast, in the co-firing of coal with olive stones the deposition rate increases as compared with the firing of unblended coal and the deposits produced present high levels of potassium, which tend to increase their stickiness.

Mean intrinsic tensile properties of stone groundwood fibers from softwood

Stone groundwood (SGW) is a fibrous matter commonly prepared in a high yield process, and mainly used for papermaking applications. In this work, the use of SGW fibers is explored as reinforcing element of polypropylene (PP) composites. Due to its chemical and superficial features, the use of coupling agents is needed for a good adhesion and stress transfer across the fiber-matrix interface. The intrinsic strength of the reinforcement is a key parameter to predict the mechanical properties of the composite and to perform an interface analysis. The main objective of the present work was the determination of the intrinsic tensile strength of stone groundwood fibers. Coupled and non-coupled PP composites from stone groundwood fibers were prepared. The influence of the surface morphology and the quality at interface on the final properties of the composite was analyzed and compared to that of fiberglass PP composites. The intrinsic tensile properties of stone groundwood fibers, as well as the fiber orientation factor and the interfacial shear strength of the current composites were determined

Tensile strength characteristics of polypropylene composites reinforced with stone groundwood fibers from softwood

The behavior of stone groundwood / polypropylene injection-molded composites was evaluated with and without coupling agent. Stone groundwood (SGW) is a fibrous material commonly prepared in a high yield process and mainly used for papermaking applications. In this work, the use of SGW fibers was explored as a reinforcing element of polypropylene (PP) composites. The surface charge density of the composite components was evaluated, as well as the fiber’s length and diameter inside the composite material. Two mixing extrusion processes were evaluated, and the use of a kinetic mixer, instead of an internal mixer, resulted in longer mean fiber lengths of the reinforcing fibers. On the other hand, the accessibility of surface hydroxyl groups of stone groundwood fibers was improved by treating the fibers with 5% of sodium hydroxide, resulting in a noticeable increase of the tensile strength of the composites, for a similar percentage of coupling agent. A new parameter called Fiber Tensile Strength Factor is defined and used as a baseline for the comparison of the properties of the different composite materials. Finally the competitiveness of stone groundwood / polypropylene / polypropylene-co-maleic anhydride system, which compared favorably to sized glass-fiber / polypropylene GF/PP and glass-fiber / polypropylene / polypropylene-co-maleic anhydride composite formulations, was quantified by means of the fiber tensile strength factor

Logistic services as competitive means : segmenting the retail market for softwood lumber

Abstract

METHANE DRY REFORMING OVER Ni SUPPORTED ON PINE SAWDUST ACTIVATED CARBON: EFFECTS OF SUPPORT SURFACE PROPERTIES AND METAL LOADING

The influence of metal loading and support surface functional groups (SFG) on methane dry reforming (MDR) over Ni catalysts supported on pine-sawdust derived activated carbon were studied. Using pine sawdust as the catalyst support precursor, the smallest variety and lowest concentration of SFG led to best Ni dispersion and highest catalytic activity, which increased with Ni loading up to 3 Ni atoms nm-2. At higher Ni loading, the formation of large metal aggregates was observed, consistent with a lower "apparen" surface area and a decrease in catalytic activity. The H2/CO ratio rose with increasing reaction temperature, indicating that increasingly important side reactions were taking place in addition to MDR.

The intrinsic mechanisms of softwood fiber damage in brown stock fiber line unit operations Lappeenranta 2010

The effects of pulp processing on softwood fiber properties strongly influence the properties of wet and dry paper webs. Pulp strength delivery studies have provided observations that much of the strength potential of long fibered pulp is lost during brown stock fiber line operations where the pulp is merely washed and transferred to the subsequent processing stages. The objective of this work was to study the intrinsic mechanisms which maycause fiber damage in the different unit operations of modern softwood brown stock processing. The work was conducted by studying the effects of industrial machinery on pulp properties with some actions of unit operations simulated in laboratory scale devices under controlled conditions. An optical imaging system was created and used to study the orientation of fibers in the internal flows during pulp fluidization in mixers and the passage of fibers through the screen openings during screening. The qualitative changes in fibers were evaluated with existing and standardized techniques. The results showed that each process stage has its characteristic effects on fiber properties: Pulp washing and mat formation in displacement washers introduced fiber deformations especially if the fibers entering the stage were intact, but it did not decrease the pulp strength properties. However, storage chests and pulp transfer after displacement washers contributed to strength deterioration. Pulp screening proved to be quite gentle, having the potential of slightly evening out fiber deformations from very deformed pulps and vice versa inflicting a marginal increase in the deformation indices if the fibers were previously intact. Pulp mixing in fluidizing industrial mixers did not have detrimental effects on pulp strength and had the potential of slightly evening out the deformations, provided that the intensity of fluidization was high enough to allow fiber orientation with the flow and that the time of mixing was short. The chemical and mechanical actions of oxygen delignification had two distinct effects on pulp properties: chemical treatment clearly reduced pulp strength with and without mechanical treatment, and the mechanical actions of process machinery introduced more conformability to pulp fibers, but did not clearly contribute to a further decrease in pulp strength. The chemical composition of fibers entering the oxygen stage was also found to affect the susceptibility of fibers to damage during oxygen delignification. Fibers with the smallest content of xylan were found to be more prone to irreversibledeformations accompanied with a lower tensile strength of the pulp. Fibers poor in glucomannan exhibited a lower fiber strength while wet after oxygen delignification as compared to the reference pulp. Pulps with the smallest lignin content on the other hand exhibited improved strength properties as compared to the references.

VOC emissions and control techniques in softwood veneer dryers

The objective in this Master’s Thesis was to determine VOC emissions from veneer drying in softwood plywood manufacturing. Emissions from plywood industry have become an important factor because of the tightened regulations worldwide. In this Thesis is researched quality and quantity of the VOCs from softwood veneer drying. One of the main objectives was to find out suitable cleaning techniques for softwood VOC emissions. In introduction part is presented veneer drying machines, wood mechanical and chemical properties. VOC control techniques and specified VOC limits are introduced also in the introduction part. Plywood mills have not had interest to VOC emissions previously nevertheless nowadays plywood mills worldwide must consider reduction of the emissions. This Thesis includes measuring of emissions from softwood veneer dryer, analyzation of measured test results and reviewing results. Different air conditions inside of the dryer were considered during planning of the measurements. Results of the emissions measurements were compared to the established laws. Results from this Thesis were softwood veneer dryer emissions in different air conditions. Emission control techniques were also studied for softwood veneer dryer emissions for further specific research.

Action of laccase on mechanical softwood pulps

Träfibrernas naturliga egenskaper begränsar deras användning i många tillämpningar. Träfibrernas egenskaper kan modifieras genom att binda nya komponenter med önskade egenskaper till fiberns yta. DI Stina Grönqvist bevisade i sin avhandling att nya funktionella grupper kan bindas till ligninhaltiga träfibrer genom att aktivera ytligninet med lackasenzym. Resultaten kan utnyttjas till att förbättra de traditionella träfibrernas och fiberprodukternas egenskaper samt att hitta nya tillämpningar för träfibrerna. ”Om träfibrerna t.ex. modifieras så att de blir vattenavstötande kan de modifierade träfibrerna användas istället för plast i förpackningar” berättar Stina Grönqvist. Syftet med denna avhandling var att undersöka effekterna av lackasenzym på TMP (termomekanisk massa) och dess fraktioner. I Finland tillverkas TMP av gran och massan innehåller rikligt med lignin. När ytligninet på träfibrernas yta modifieras med hjälp av oxiderande enzymer, såsom lackas, bildas reaktiva radikaler i ligninen på fibrernas ytor. De bildade radikalerna kan utnyttjas till att binda komponenter med nya egenskaper till fiberytan. För att kunna utnyttja den fulla potentialen av den lackasbaserade modifieringsmetoden behövs mera information om så väl de faktorer som påverkar bildningen av radikaler som om mekanismerna hur de nya komponenterna binds till fibrerna ___________________________________ Puukuitujen luontaiset ominaisuudet rajoittavat niiden hyödyntämistä joissakin sovelluksissa. Ominaisuuksia voidaan kuitenkin muuttaa liittämällä kuidun pintaan uusia yhdisteitä. DI Stina Grönqvist osoitti väitöstyössään, että uusia kuitujen ominaisuuksia muuttavia funktionaalisia yhdisteitä voidaan sitoa ligniinipitoisiin puukuituihin aktivoimalla kuitujen pinnan ligniiniä lakkaasi-entsyymillä. Tutkimuksen tuloksia voidaan hyödyntää ligniinipitoisten puukuitujen ominaisuuksien parantamiseen ja jopa täysin uusien ominaisuuksien kehittämiseen. ”Jos kuituja muutetaan vettä hylkiväksi sitomalla kuituihin vettä hylkiviä yhdisteitä entsyymien avulla, voidaan puukuituja käyttää korvaamaan muovia pakkauksissa”, kertoo Stina Grönqvist. Väitöstyön kohteena oli TMP-massan eli kuumahiertämällä valmistetun mekaanisen puumassojen ja niiden fraktioiden muokkaaminen lakkaasi-entsyymillä (TMP, Thermomechanical pulp). Suomalainen TMP-massa valmistetaan kuusesta ja siinä on runsaasti muokkaamatonta ligniiniä. Kun puukuidun pinnan ligniiniä muokataan hapettavilla entsyymeillä, muodostuu kuidun pintaan reaktiivisia radikaaleja. Syntyneiden radikaalien avulla kuituihin voidaan liittää yhdisteitä, jotka antavat kuidulle uusia ominaisuuksia. Menetelmän tarjoamien mahdollisuuksien hyödyntämiseksi tarvitaan tietoa kuidun radikalisointiin ja yhdisteiden liittämiseen vaikuttavista tekijöistä.

Ionic liquid mediated biomass deconstruction: from analysis challenges to fermentable sugars

Ionic liquids, ILs, have recently been studied with accelerating interest to be used for a deconstruction/fractionation, dissolution or pretreatment processing method of lignocellulosic biomass. ILs are usually utilized combined with heat. Regarding lignocellulosic recalcitrance toward fractionation and IL utilization, most of the studies concern IL utilization in the biomass fermentation process prior to the enzymatic hydrolysis step. It has been demonstrated that IL-pretreatment gives more efficient hydrolysis of the biomass polysaccharides than enzymatic hydrolysis alone. Both cellulose (especially cellulose) and lignin are very resistant towards fractionation and even dissolution methods. As an example, it can be mentioned that softwood, hardwood and grass-type plant species have different types of lignin structures leading to the fact that softwood lignin (guaiacyl lignin dominates) is the most difficult to solubilize or chemically disrupt. In addition to the known conventional biomass processing methods, several ILs have also been found to efficiently dissolve either cellulose and/or wood samples – different ILs are suitable for different purposes. An IL treatment of wood usually results in non-fibrous pulp, where lignin is not efficiently separated and wood components are selectively precipitated, as cellulose is not soluble or degradable in ionic liquids under mild conditions. Nevertheless, new ILs capable of rather good fractionation performance have recently emerged. The capability of the IL to dissolve or deconstruct wood or cellulose depends on several factors, (e.g. sample origin, the particle size of the biomass, mechanical treatments as pulverization, initial biomassto-IL ratio, water content of the biomass, possible impurities of IL, reaction conditions, temperature etc). The aim of this study was to obtain (fermentable) saccharides and other valuable chemicals from wood by a combined heat and IL-treatment. Thermal treatments alone contribute to the degradation of polysaccharides (e.g. 150 °C alone is said to cause the degradation of polysaccharides), thus temperatures below that should be used, if the research interest lies on the IL effectiveness. On the other hand, the efficiency of the IL-treatment can also be enhanced to combine other treatment methods, (e.g. microwave heating). The samples of spruce, pine and birch sawdust were treated with either 1-Ethyl-3-methylimidazolium chloride, Emim Cl, or 1-Ethyl-3-methylimidazolium acetate, Emim Ac, (or with ionized water for comparison) at various temperatures (where focus was between 80 and 120 °C). The samples were withdrawn at fixed time intervals (the main interest treatment time area lied between 0 and 100 hours). Double experiments were executed. The selected mono- and disaccharides, as well as their known degradation products, 5-hydroxymethylfurfural, 5-HMF, and furfural were analyzed with capillary electrophoresis, CE, and high-performance liquid chromatography, HPLC. Initially, even GC and GC-MS were utilized. Galactose, glucose, mannose and xylose were the main monosaccharides that were present in the wood samples exposed to ILs at elevated temperatures; in addition, furfural and 5-HMF were detected; moreover, the quantitative amount of the two latter ones were naturally increasing in line with the heating time or the IL:wood ratio.