Assessment of the quality of cottage cheese produced from standard and protein-fortified skim milk

The effects of milk protein fortification on the texture and microstructure of cottage cheese curd were evaluated. Protein powder (92.6% protein) was added to the skim milk at a level of 0.4% (w/w) to produce curds. Control curds with no protein powder addition were also produced. These curds were analysed for differences in yield, total solids, curd size, texture and structure. It was found that the addition of protein powder contributed to a significant yield increase, which can be attributed to increased water retention, with better curd size distribution. Control curds were firmer than the fortified curds and the structure showed less open-pore structure as revealed by electron microscopy. However, the addition of dressing masked the textural differences, and a sensory panel was unable to distinguish between cheeses produced from fortified milk and controls.

The effect of free Ca2+ on the heat stability and other characteristics of low-heat skim milk powder

Low-heat skim milk powder (SMP), reconstituted to 25% total solids, was found to have poor heat stability. This could be improved by reducing the free Ca2+ concentration to 1.14 mm, or lower, by the addition of either Amberlite IR-120 ion-exchange resin in its sodium form or tri-sodium citrate in skim milk prior to evaporation and spray drying. Reduction in Ca2+ concentration was accompanied by increases in pH, particle size, and kinematic viscosity, and by a reduction in zeta-potential and changes in colour. In-container sterilisation of the reconstituted powder increased particle size, zeta-potential, kinematic viscosity and a* and b* values. However. Ca2+ concentration, pH and whiteness decreased. This study elucidated the importance of Ca2+ concentration and pH on heat stability of low-heat SMP, suggesting that Ca2+ concentration and pH in bulk milk are useful indicators for ensuring that spray dried milk powder has good heat stability. (C) 2009 Elsevier Ltd. All rights reserved.

A comparison of reverse osmosis, nanofiltration and ultrafiltration as concentration processes for skim milk prior to drying

Skim milk was concentrated by reverse osmosis (RO), nanofiltration (NF) and ultrafiltration (UF) and the retentates were spray-dried. The resulting powders were reconstituted to 25% TS and sterilised to evaluate their heat stability. Reverse osmosis led to maximum retention of calcium, a fall in pH for its retentate and its reconstituted powder. All RO powders produced a weak gel on heating. Some calcium was lost during NF and a greater amount during UF. Their resulting reconstituted powders had a higher pH than those produced by RO. Powders produced by UF showed poor heat stability. Only one powder produced by NF showed good heat stability. This could be improved by addition of stabilisers at appropriate addition rates.

Effect of dairy-based protein sources and temperature on growth, acidification and exopolysaccharide production of Bifidobacterium strains in skim milk

The aim of the present study was to find out the best growing conditions for exopolysaccharide (EPS) producing bifidobacteria, which improve their functionality in yoghurt-like products. Two Bifidobacterium strains were used in this study, Bifidobacterium longum subsp. infantis CCUG 52486 and Bifidobacterium infantis NCIMB 702205. In the first part of the study the effect of casein hydrolysate, lactalbumin hydrolysate, whey protein concentrate and whey protein isolate, added at 1.5% w/v in skim milk, was evaluated in terms of cell growth and EPS production; skim milk supplemented with yeast extract served as the control. Among the various nitrogen sources, casein hydrolysate (CH) showed the highest cell growth and EPS production for both strains after 18 h incubation and therefore it was selected for subsequent work. Based on fermentation experiments using different levels of CH (from 0.5 to 2.5% w/v) it was deduced that 1.5% (w/v) CH resulted in the highest EPS production, yielding 102 and 285 mg L− 1 for B. infantis NCIMB 702205 and B. longum subsp. infantis CCUG 52486, respectively. The influence of temperature on growth and EPS production of both strains was further evaluated at 25, 30, 37 and 42 °C for up to 48 h in milk supplemented with 1.5% (w/v) CH. The temperature had a significant effect on growth, acidification and EPS production. The maximum growth and EPS production were recorded at 37 °C for both strains, whereas no EPS production was observed at 25 °C. Lower EPS production for both strains were observed at 42 °C, which is the common temperature used in yoghurt manufacturing compared to that at 37 °C. The results showed that the culture conditions have a clear effect on the growth, acidification and EPS production, and more specifically, that skim milk supplemented with 1.5% (w/v) CH could be used as a substrate for the growth of EPS-producing bifidobacteria, at 37 °C for 24 h, resulting in the production of a low fat yoghurt-like product with improved functionality.

Effect of seasonal variation on the properties of whipping cream, soft cheese and skim milk powder in the UK

Whipping cream, skim milk powder and soft cheese were produced throughout the year. Whipping cream manufactured in spring and winter produced significantly higher overrun and better serum stability, and whipping time was related to buffering capacity of raw milk. Heat stability of reconstituted skim milk powder (RSMP) at 9% TS was greater in summer and autumn, and greater than 25% TS throughout the year. It was positively related to the protein content of raw milk, but negatively with fat. In contrast to other dairy products, no significant effect of season on the properties of soft cheese was found.

Effects of milk supplementation with skim milk powder, whey protein concentrate and sodium caseinate on acidification kinetics, rheological properties and structure of nonfat stirred yogurt

Milk supplementation with milk proteins in four different levels was used to investigate the effect on acidification and textural properties of yogurt. Commercial skim milk powder was diluted in distilled water, and the supplements were added to give different enriched-milk bases; these were heat treated at 90 degrees C for 5 min. These mixtures were incubated with the bacterial cultures for fermentation in a water bath, at 42 degrees C, until pH 4.50 was reached. Chemical changes during fermentation were followed by measuring the pH. Protein concentration measurements, microbial counts of Lactobacillus bulgaricus and Streptococcus thermophilus, and textural properties (G`, G ``, yield stress and firmness) were determined after 24 h of storage at 4 degrees C. Yogurt made with milk supplemented with sodium caseinate resulted in significant properties changes, which were decrease in fermentation time, and increase in yield stress, storage modulus, and firmness, with increases in supplement level. Microstructure also differed from that of yogurt produced with milk supplemented with skim milk powder or sodium caseinate. (C) 2009 Elsevier Ltd. All rights reserved.

Comparison of texture of yogurt made from conventionally treated milk and UHT milk fortified with low-heat skim milk powder

The textures of yogurt made from ultra-high temperature (UHT) treated and conventionally treated milks at high total solids were investigated. The yogurt premixes, fortified with low-heat skim milk powder to 16%, 18%, and 20% total solids, were UHT processed at 143 degreesC for 6 s and heated at 85 degreesC for 30 min using the conventional method. The onset of gelation was delayed in the UHT-processed milk compared with conventionally heated milk. During fermentation, the viscosity of yogurt made, from UHT-treated milk at 20% total solids was close to that of yogurt made from conventionally treated milk with 16% total solids. However, after storage for greater than or equal to1 d, the yogurt made from UHT-treated milk had lower viscosity and gel strength than the yogurt made from conventionally treated milk. The solids level had no influence on yogurt culture growth.

Measurement of glass-rubber transition temperature of skim milk powder by static mechanical test

Stickiness behavior of skim milk powder was investigated based on the mechanical property of the material during the glass-rubber transition. A thermally controlled device was developed for the static mechanical test. This device was attached to a texture analyzer, and skim milk powder, which was used as a model sample, was tested for its glass-rubber transition temperature (Tg-r) using static compression technique (creep test). Changes in compression probe distance as a function of temperature were recorded. Tg-r was determined, in the region where changes in the probe distance were observed, by using linear regression technique. The effect of sample quantity, compression force, and heating rate on the determination of Tg-r was investigated. All these parameters significantly influenced the Tg-r determination (p < 0.05). The Tg-r of skim milk powder measured by this novel technique was found closely correlated to its glass transition temperature (T-g) measured by DSC.

The influence of temperature on the foaming of milk

The effect of temperature (5-85 °C) on the foaming properties of cows' milk was investigated. The foaming properties of milk as a function of temperature varied considerably depending on fat content and the processing conditions used in manufacture. Skim milk foams were most stable when formed at 45 °C. Milk fat had a detrimental effect on foam formation and stability of whole milk especially in the temperature range 15-45 °C. The detrimental effects of milk fat on foaming properties were reduced by homogenization and ultra-high-temperature (UHT) treatment. No correlation was observed between foam formation and surface tension of whole milk in the temperature range 15-45 °C. There was a pronounced difference in the bubble size distributions of whole milk and skim milk especially at half-life of the foams. Bubbles in whole milk foams were smaller and showed a higher degree of rupture as a result of coalescence than those in skim milk foams.

Nicotinamide Riboside Is a Major NAD+ Precursor Vitamin in Cow Milk

Background: Nicotinamide riboside (NR) is a recently discovered NAD+ precursor vitamin with a unique biosynthetic pathway. Although the presence of NR in cow milk has been known for more than a decade, the concentration of NR with respect to the other NAD+ precursors was unknown.

Objective: We aimed to determine NAD+ precursor vitamin concentration in raw samples of milk from individual cows and from commercially available cow milk.

Methods: LC tandem mass spectrometry and isotope dilution technologies were used to quantify NAD+ precursor vitamin concentration and to measure NR stability in raw and commercial milk. Nuclear magnetic resonance (NMR) spectroscopy was used to test for NR binding to substances in milk.

Results: Cow milk typically contained ∼12 μmol NAD+ precursor vitamins/L, of which 60% was present as nicotinamide and 40% was present as NR. Nicotinic acid and other NAD+ metabolites were below the limits of detection. Milk from samples testing positive for Staphylococcus aureus contained lower concentrations of NR (Spearman ρ = −0.58, P = 0.014), and NR was degraded by S. aureus. Conventional milk contained more NR than milk sold as organic. Nonetheless, NR was stable in organic milk and exhibited an NMR spectrum consistent with association with a protein fraction in skim milk.

Conclusions: NR is a major NAD+ precursor vitamin in cow milk. Control of S. aureus may be important to preserve the NAD+ precursor vitamin concentration of milk.

A novel technique for differentiation of proteins in the development of acid gel structure from control and heat treated milk using confocal scanning laser microscopy

The incorporation of caseins and whey proteins into acid gels produced from unheated and heat treated skimmed milk was studied by confocal scanning laser microscopy (CSLM) using fluorescent labelled proteins. Bovine casein micelles were labelled using Alexa Fluor 594, while whey proteins were labelled using Alexa Fluor 488. Samples of the labelled protein solutions were introduced into aliquots of pasteurised skim milk, and skim milk heated to 90 degrees C for 2 min and 95 degrees C for 8 min. The milk was acidified at 40 degrees C to a final pH of 4.4 using 20 g gluconodelta-lactone/l (GDL). The formation of gels was observed with CSLM at two wavelengths (488 nm and 594 nm), and also by visual and rheological methods. In the control milk, as pH decreased distinct casein aggregates appeared, and as further pH reduction occurred, the whey proteins could be seen to coat the casein aggregates. With the heated milks, the gel structure was formed of continuous strands consisting of both casein and whey protein. The formation of the gel network was correlated with an increase in the elastic modulus for all three treatments, in relation to the severity of heat treatment. This model system allows the separate observation of the caseins and whey proteins, and the study of the interactions between the two protein fractions during the formation of the acid gel structure, on a real-time basis. The system could therefore be a valuable tool in the study of structure formation in yoghurt and other dairy protein systems.

Effects of addition of phenolic compounds on the acid gelation of milk

Tannic acid (0.1–1%, w/w) and gallic acid (0.3–1%, w/w) were added to skim milk prior to acidification with GDL. The acid gelation of tannic and gallic acid fortified milk had a faster gelation time in comparison with the control gel without phenolic compounds. The addition of tannic acid and gallic acid (up to 0.8%) to the milk resulted in a higher storage modulus (G′), decrease in the water mobility (T2 time) and had no significant effect on the syneresis index (SI). However, the inclusion of 1% gallic acid resulted in a significant decrease in G′, a significant increase in the SI and a wider T2 distribution. Lowering the temperature of the gels from 30 to 5 °C caused the G′ for the gels with gallic and tannic acid to increase significantly in comparison with the control, possibly due to increased hydrogen bonding in the presence of phenolic compounds

Optimization of the rheological properties of probiotic yoghurts supplemented with milk proteins

This study aimed to optimize the rheological properties of probiotic yoghurts supplemented with skimmed milk powder (SMP) whey protein concentrate (WPC) and sodium caseinate (Na-Cn) by using an experimental design type simplex-centroid for mixture modeling It Included seven batches/trials three were supplemented with each type of the dairy protein used three corresponding to the binary mixtures and one to the ternary one in order to increase protein concentration in 1 g 100 g(-1) of final product A control experiment was prepared without supplementing the milk base Processed milk bases were fermented at 42 C until pH 4 5 by using a starter culture blend that consisted of Streptococcus thermophilus Lactobacillus delbrueckii subsp bulgaricus and Bifidobacterium (Humans subsp lactis The kinetics of acidification was followed during the fermentation period as well the physico-chemical analyses enumeration of viable bacteria and theological characteristics of the yoghurts Models were adjusted to the results (kinetic responses counts of viable bacteria and theological parameters) through three regression models (linear quadratic and cubic special) applied to mixtures The results showed that the addition of milk proteins affected slightly acidification profile and counts of S thermophilus and B animal`s subsp lactis but it was significant for L delbrueckii subsp bulgaricus Partially-replacing SMP (45 g/100 g) with WPC or Na-Cn simultaneously enhanced the theological properties of probiotic yoghurts taking into account the kinetics of acidification and enumeration of viable bacteria (C) 2010 Elsevier Ltd All rights reserved

Influence of milk type and addition of passion fruit peel powder on fermentation kinetics, texture profile and bacterial viability in probiotic yoghurts

The effect of the addition of passion fruit peel powder (PFPP) on the fermentation kinetics and texture parameters, post-acidification and bacteria counts of probiotic yoghurts made with two milk types were evaluated during 28 days of storage at 4 degrees C. Milks were fermented by Streptococcus thermophilus and Lactobacillus delbrueckii subsp. bulgaricus (CY340), and one strain of probiotic bacteria: Lactobacillus acidophilus (L10 and NCFM), Bifidobacterium animalis subsp. lactis (8104 and HN019). The addition of PFPP reduced significantly fermentation time of skim milk co-fermented by the strains L10, NCFM and HN019. At the end of 28-day shelf-life, counts of B. lactis Bl04 were about 1 Log CFU mL(-1) higher in whole yoghurt fermented with PFPP regarding its control but, in general, the addition of PFPP had less influence on counts than the milk type itself. The titratable acidity in yoghurts with PFPP was significantly higher than in their respective controls, and in skim yoghurts higher than in the whole ones. The PFPP increased firmness, consistency (except for the NCFM strain of L acidophilus) and cohesiveness of all skim yoghurts. The results point out the suitability of using passion fruit by-product in the formulation of both skim and whole probiotic yoghurts. (C) 2012 Elsevier Ltd. All rights reserved.