Mathematical programming model for heat exchanger design through optimization of partial objectives

Mathematical programming can be used for the optimal design of shell-and-tube heat exchangers (STHEs). This paper proposes a mixed integer non-linear programming (MINLP) model for the design of STHEs, following rigorously the standards of the Tubular Exchanger Manufacturers Association (TEMA). Bell–Delaware Method is used for the shell-side calculations. This approach produces a large and non-convex model that cannot be solved to global optimality with the current state of the art solvers. Notwithstanding, it is proposed to perform a sequential optimization approach of partial objective targets through the division of the problem into sets of related equations that are easier to solve. For each one of these problems a heuristic objective function is selected based on the physical behavior of the problem. The global optimal solution of the original problem cannot be ensured even in the case in which each of the sub-problems is solved to global optimality, but at least a very good solution is always guaranteed. Three cases extracted from the literature were studied. The results showed that in all cases the values obtained using the proposed MINLP model containing multiple objective functions improved the values presented in the literature.

Energy efficiency optimization in hardware-constrained large-scale MIMO systems

Large-scale multiple-input multiple-output (MIMO) communication systems can bring substantial improvement in spectral efficiency and/or energy efficiency, due to the excessive degrees-of-freedom and huge array gain. However, large-scale MIMO is expected to deploy lower-cost radio frequency (RF) components, which are particularly prone to hardware impairments. Unfortunately, compensation schemes are not able to remove the impact of hardware impairments completely, such that a certain amount of residual impairments always exists. In this paper, we investigate the impact of residual transmit RF impairments (RTRI) on the spectral and energy efficiency of training-based point-to-point large-scale MIMO systems, and seek to determine the optimal training length and number of antennas which maximize the energy efficiency. We derive deterministic equivalents of the signal-to-noise-and-interference ratio (SINR) with zero-forcing (ZF) receivers, as well as the corresponding spectral and energy efficiency, which are shown to be accurate even for small number of antennas. Through an iterative sequential optimization, we find that the optimal training length of systems with RTRI can be smaller compared to ideal hardware systems in the moderate SNR regime, while larger in the high SNR regime. Moreover, it is observed that RTRI can significantly decrease the optimal number of transmit and receive antennas.

Extracellular β-glucosidase Production by a Marine Aspergillus sydowii BTMFS 55 under Solid State Fermentation Using Statistical Experimental Design

A potential fungal strain producing extracellular β-glucosidase enzyme was isolated from sea water and identified as ^ëéÉêJ Öáääìë=ëóÇçïáá BTMFS 55 by a molecular approach based on 28S rDNA sequence homology which showed 93% identity with already reported sequences of ^ëéÉêÖáääìë=ëóÇçïáá in the GenBank. A sequential optimization strategy was used to enhance the production of β-glucosidase under solid state fermentation (SSF) with wheat bran (WB) as the growth medium. The two-level Plackett-Burman (PB) design was implemented to screen medium components that influence β-glucosidase production and among the 11 variables, moisture content, inoculums, and peptone were identified as the most significant factors for β-glucosidase production. The enzyme was purified by (NH4)2SO4 precipitation followed by ion exchange chromatography on DEAE sepharose. The enzyme was a monomeric protein with a molecular weight of ~95 kDa as determined by SDS-PAGE. It was optimally active at pH 5.0 and 50°C. It showed high affinity towards éNPG and enzyme has a hã and sã~ñ of 0.67 mM and 83.3 U/mL, respectively. The enzyme was tolerant to glucose inhibition with a há of 17 mM. Low concentration of alcohols (10%), especially ethanol, could activate the enzyme. A considerable level of ethanol could produce from wheat bran and rice straw after 48 and 24 h, respectively, with the help of p~ÅÅÜ~êçãóÅÉë=ÅÉêÉîáëá~É in presence of cellulase and the purified β-glucosidase of ^ëéÉêÖáääìë=ëóÇçïáá BTMFS 55.

Sistemas de gestión de puentes : optimización de estrategias de mantenimiento : implementación en redes locales de carreteras

En la actualidad, y en consonancia con la tendencia de “sostenibilidad” extendida a todos los campos y parcelas de la ciencia, nos encontramos con un área de estudio basado en la problemática del inevitable deterioro de las estructuras existentes, y la gestión de las acciones a realizar para mantener las condiciones de servicio de los puentes y prolongar su vida útil. Tal y como se comienza a ver en las inversiones en los países avanzados, con una larga tradición en el desarrollo de sus infraestructuras, se muestra claramente el nuevo marco al que nos dirigimos. Las nuevas tendencias van encaminadas cada vez más a la conservación y mantenimiento, reduciéndose las partidas presupuestarias destinadas a nuevas actuaciones, debido a la completa vertebración territorial que se ha ido instaurando en estos países, entre los que España se encuentra. Este nutrido patrimonio de infraestructuras viarias, que cuentan a su vez con un importante número de estructuras, hacen necesarias las labores de gestión y mantenimiento de los puentes integrantes en las mismas. Bajo estas premisas, la tesis aborda el estado de desarrollo de la implementación de los sistemas de gestión de puentes, las tendencias actuales e identificación de campos por desarrollar, así como la aplicación específica a redes de carreteras de escasos recursos, más allá de la Red Estatal. Además de analizar las diversas metodologías de formación de inventarios, realización de inspecciones y evaluación del estado de puentes, se ha enfocado, como principal objetivo, el desarrollo de un sistema específico de predicción del deterioro y ayuda a la toma de decisiones. Este sistema, adicionalmente a la configuración tradicional de criterios de formación de bases de datos de estructuras e inspecciones, plantea, de forma justificada, la clasificación relativa al conjunto de la red gestionada, según su estado de condición. Eso permite, mediante técnicas de optimización, la correcta toma de decisiones a los técnicos encargados de la gestión de la red. Dentro de los diversos métodos de evaluación de la predicción de evolución del deterioro de cada puente, se plantea la utilización de un método bilineal simplificado envolvente del ajuste empírico realizado y de los modelos markovianos como la solución más efectiva para abordar el análisis de la predicción de la propagación del daño. Todo ello explotando la campaña experimenta realizada que, a partir de una serie de “fotografías técnicas” del estado de la red de puentes gestionados obtenidas mediante las inspecciones realizadas, es capaz de mejorar el proceso habitual de toma de decisiones. Toda la base teórica reflejada en el documento, se ve complementada mediante la implementación de un Sistema de Gestión de Puentes (SGP) específico, adaptado según las necesidades y limitaciones de la administración a la que se ha aplicado, en concreto, la Dirección General de Carreteras de la Junta de Comunidades de Castilla-La Mancha, para una muestra representativa del conjunto de puentes de la red de la provincia de Albacete, partiendo de una situación en la que no existe, actualmente, un sistema formal de gestión de puentes. Tras un meditado análisis del estado del arte dentro de los Capítulos 2 y 3, se plantea un modelo de predicción del deterioro dentro del Capítulo 4 “Modelo de Predicción del Deterioro”. De la misma manera, para la resolución del problema de optimización, se justifica la utilización de un novedoso sistema de optimización secuencial elegido dentro del Capítulo 5, los “Algoritmos Evolutivos”, en sus diferentes variantes, como la herramienta matemática más correcta para distribuir adecuadamente los recursos económicos dedicados a mantenimiento y conservación de los que esta administración pueda disponer en sus partidas de presupuesto a medio plazo. En el Capítulo 6, y en diversos Anexos al presente documento, se muestran los datos y resultados obtenidos de la aplicación específica desarrollada para la red local analizada, utilizando el modelo de deterioro y optimización secuencial, que garantiza la correcta asignación de los escasos recursos de los que disponen las redes autonómicas en España. Se plantea con especial interés la implantación de estos sistemas en la red secundaria española, debido a que reciben en los últimos tiempos una mayor responsabilidad de gestión, con recursos cada vez más limitados. Finalmente, en el Capítulo 7, se plantean una serie de conclusiones que nos hacen reflexionar de la necesidad de comenzar a pasar, en materia de gestión de infraestructuras, de los estudios teóricos y los congresos, hacia la aplicación y la práctica, con un planteamiento que nos debe llevar a cambios importantes en la forma de concebir la labor del ingeniero y las enseñanzas que se imparten en las escuelas. También se enumeran las aportaciones originales que plantea el documento frente al actual estado del arte. Se plantean, de la misma manera, las líneas de investigación en materia de Sistemas de Gestión de Puentes que pueden ayudar a refinar y mejorar los actuales sistemas utilizados. In line with the development of "sustainability" extended to all fields of science, we are faced with the inevitable and ongoing deterioration of existing structures, leading nowadays to the necessary management of maintaining the service conditions and life time extension of bridges. As per the increased amounts of money that can be observed being spent in the countries with an extensive and strong tradition in the development of their infrastructure, the trend can be clearly recognized. The new tendencies turn more and more towards conservation and maintenance, reducing programmed expenses for new construction activities, in line with the already wellestablished territorial structures, as is the case for Spain. This significant heritage of established road infrastructure, consequently containing a vast number of structures, imminently lead to necessary management and maintenance of the including bridges. Under these conditions, this thesis focusses on the status of the development of the management implementation for bridges, current trends, and identifying areas for further development. This also includes the specific application to road networks with limited resources, beyond the national highways. In addition to analyzing the various training methodologies, inventory inspections and condition assessments of bridges, the main objective has been the development of a specific methodology. This methodology, in addition to the traditional system of structure and inspection database training criteria, sustains the classification for the entire road network, according to their condition. This allows, through optimization techniques, for the correct decision making by the technical managers of the network. Among the various methods for assessing the evolution forecast of deterioration of each bridge, a simplified bilinear envelope adjustment made empirical method and Markov models as the most effective solution to address the analysis of predicting the spread of damage, arising from a "technical snapshot" obtained through inspections of the condition of the bridges included in the investigated network. All theoretical basis reflected in the document, is completed by implementing a specific Bridges Management System (BMS), adapted according to the needs and limitations of the authorities for which it has been applied, being in this case particularly the General Highways Directorate of the autonomous region of Castilla-La Mancha, for a representative sample of all bridges in the network in the province of Albacete, starting from a situation where there is currently no formal bridge management system. After an analysis of the state of the art in Chapters 2 and 3, a new deterioration prediction model is developed in Chapter 4, "Deterioration Prediction Model". In the same way, to solve the optimization problem is proposed the use of a singular system of sequential optimization elected under Chapter 5, the "Evolutionary Algorithms", the most suitable mathematical tool to adequately distribute the economic resources for maintenance and conservation for mid-term budget planning. In Chapter 6, and in the various appendices, data and results are presented of the developed application for the analyzed local network, from the optimization model, which guarantees the correct allocation of scarce resources at the disposal of authorities responsible for the regional networks in Spain. The implementation of these systems is witnessed with particular interest for the Spanish secondary network, because of the increasing management responsibility, with decreasing resources. Chapter 7 presents a series of conclusions that triggers to reconsider shifting from theoretical studies and conferences towards a practical implementation, considering how to properly conceive the engineering input and the related education. The original contributions of the document are also listed. In the same way, the research on the Bridges Management System can help evaluating and improving the used systematics.

Sequential injection analysis (SIA) and response surface methodology: A versatile small volume approach for optimization of photo-Fenton processes

Optimization of photo-Fenton degradation of copper phthalocyanine blue was achieved by response surface methodology (RSM) constructed with the aid of a sequential injection analysis (SIA) system coupled to a homemade photo-reactor. Highest degradation percentage was obtained at the following conditions [H(2)O(2)]/[phthalocyanine] = 7, [H(2)O(2)]/[FeSO(4)] = 10, pH = 2.5, and stopped flow time in the photo reactor = 30 s. The SIA system was designed to prepare a monosegment containing the reagents and sample, to pump it toward the photo-reactor for the specified time and send the products to a flow-through spectrophotometer for monitoring the color reduction of the dye. Changes in parameters such as reagent molar ratios. residence time and pH were made by modifications in the software commanding the SI system, without the need for physical reconfiguration of reagents around the selection valve. The proposed procedure and system fed the statistical program with degradation data for fast construction of response surface plots. After optimization, 97% of the dye was degraded. (C) 2009 Elsevier B.V. All rights reserved.

Applying sequential injection analysis (SIA) and response surface methodology for optimization of Fenton-based processes

This work presents the use of sequential injection analysis (SIA) and the response surface methodology as a tool for optimization of Fenton-based processes. Alizarin red S dye (C.I. 58005) was used as a model compound for the anthraquinones family. whose pigments have a large use in coatings industry. The following factors were considered: [H(2)O(2)]:[Alizarin] and [H(2)O(2)]:[FeSO(4)] ratios and pH. The SIA system was designed to add reagents to the reactor and to perform on-line sampling of the reaction medium, sending the samples to a flow-through spectrophotometer for monitoring the color reduction of the dye. The proposed system fed the statistical program with degradation data for fast construction of response surface plots. After optimization, 99.7% of the dye was degraded and the TOC content was reduced to 35% of the original value. Low reagents consumption and high sampling throughput were the remarkable features of the SIA system. (C) 2008 Published by Elsevier B.V.

Optimization Strategies Based on Sequential Quadratic Programming Applied for a Fermentation Process for Butanol Production

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Particle swarm optimization with sequential niche technique for dynamic finite element model updating

Peer reviewed

Dynamic Design of Piezoelectric Laminated Sensors and Actuators using Topology Optimization

Sensors and actuators based on piezoelectric plates have shown increasing demand in the field of smart structures, including the development of actuators for cooling and fluid-pumping applications and transducers for novel energy-harvesting devices. This project involves the development of a topology optimization formulation for dynamic design of piezoelectric laminated plates aiming at piezoelectric sensors, actuators and energy-harvesting applications. It distributes piezoelectric material over a metallic plate in order to achieve a desired dynamic behavior with specified resonance frequencies, modes, and enhanced electromechanical coupling factor (EMCC). The finite element employs a piezoelectric plate based on the MITC formulation, which is reliable, efficient and avoids the shear locking problem. The topology optimization formulation is based on the PEMAP-P model combined with the RAMP model, where the design variables are the pseudo-densities that describe the amount of piezoelectric material at each finite element and its polarization sign. The design problem formulated aims at designing simultaneously an eigenshape, i.e., maximizing and minimizing vibration amplitudes at certain points of the structure in a given eigenmode, while tuning the eigenvalue to a desired value and also maximizing its EMCC, so that the energy conversion is maximized for that mode. The optimization problem is solved by using sequential linear programming. Through this formulation, a design with enhancing energy conversion in the low-frequency spectrum is obtained, by minimizing a set of first eigenvalues, enhancing their corresponding eigenshapes while maximizing their EMCCs, which can be considered an approach to the design of energy-harvesting devices. The implementation of the topology optimization algorithm and some results are presented to illustrate the method.

Tailoring vibration mode shapes using topology optimization and functionally graded material concepts

Tailoring specified vibration modes is a requirement for designing piezoelectric devices aimed at dynamic-type applications. A technique for designing the shape of specified vibration modes is the topology optimization method (TOM) which finds an optimum material distribution inside a design domain to obtain a structure that vibrates according to specified eigenfrequencies and eigenmodes. Nevertheless, when the TOM is applied to dynamic problems, the well-known grayscale or intermediate material problem arises which can invalidate the post-processing of the optimal result. Thus, a more natural way for solving dynamic problems using TOM is to allow intermediate material values. This idea leads to the functionally graded material (FGM) concept. In fact, FGMs are materials whose properties and microstructure continuously change along a specific direction. Therefore, in this paper, an approach is presented for tailoring user-defined vibration modes, by applying the TOM and FGM concepts to design functionally graded piezoelectric transducers (FGPT) and non-piezoelectric structures (functionally graded structures-FGS) in order to achieve maximum and/or minimum vibration amplitudes at certain points of the structure, by simultaneously finding the topology and material gradation function. The optimization problem is solved by using sequential linear programming. Two-dimensional results are presented to illustrate the method.

Multi-criteria design optimization study of solvent extraction in mixer–settler units

Solvent extraction is considered as a multi-criteria optimization problem, since several chemical species with similar extraction kinetic properties are frequently present in the aqueous phase and the selective extraction is not practicable. This optimization, applied to mixer–settler units, considers the best parameters and operating conditions, as well as the best structure or process flow-sheet. Global process optimization is performed for a specific flow-sheet and a comparison of Pareto curves for different flow-sheets is made. The positive weight sum approach linked to the sequential quadratic programming method is used to obtain the Pareto set. In all investigated structures, recovery increases with hold-up, residence time and agitation speed, while the purity has an opposite behaviour. For the same treatment capacity, counter-current arrangements are shown to promote recovery without significant impairment in purity. Recycling the aqueous phase is shown to be irrelevant, but organic recycling with as many stages as economically feasible clearly improves the design criteria and reduces the most efficient organic flow-rate.

Combining data mining and evolutionary computation for multi-criteria optimization of earthworks

Earthworks tasks aim at levelling the ground surface at a target construction area and precede any kind of structural construction (e.g., road and railway construction). It is comprised of sequential tasks, such as excavation, transportation, spreading and compaction, and it is strongly based on heavy mechanical equipment and repetitive processes. Under this context, it is essential to optimize the usage of all available resources under two key criteria: the costs and duration of earthwork projects. In this paper, we present an integrated system that uses two artificial intelligence based techniques: data mining and evolutionary multi-objective optimization. The former is used to build data-driven models capable of providing realistic estimates of resource productivity, while the latter is used to optimize resource allocation considering the two main earthwork objectives (duration and cost). Experiments held using real-world data, from a construction site, have shown that the proposed system is competitive when compared with current manual earthwork design.

Modern optimization in earthwork construction

Earthworks tasks are often regarded in transportation projects as some of the most demanding processes. In fact, sequential tasks such as excavation, transportation, spreading and compaction are strongly based on heavy mechanical equipment and repetitive processes, thus becoming as economically demanding as they are time-consuming. Moreover, actual construction requirements originate higher demands for productivity and safety in earthwork constructions. Given the percentual weight of costs and duration of earthworks in infrastructure construction, the optimal usage of every resource in these tasks is paramount. Considering the characteristics of an earthwork construction, it can be looked at as a production line based on resources (mechanical equipment) and dependency relations between sequential tasks, hence being susceptible to optimization. Up to the present, the steady development of Information Technology areas, such as databases, artificial intelligence and operations research, has resulted in the emergence of several technologies with potential application bearing that purpose in mind. Among these, modern optimization methods (also known as metaheuristics), such as evolutionary computation, have the potential to find high quality optimal solutions with a reasonable use of computational resources. In this context, this work describes an optimization algorithm for earthworks equipment allocation based on a modern optimization approach, which takes advantage of the concept that an earthwork construction can be regarded as a production line.

Development of procedures for the design, optimization and manufacturing of customized orthopaedic and trauma implants: Geometrical/anatomical modelling from 3D medical imaging

Tese de Doutoramento (Programa Doutoral em Engenharia Biomédica)

Development of an intelligent earthwork optimization system

Tese de Doutoramento em Engenharia Civil.