Performance Septic Systems: Does an Advanced Septic System Provide Adequate Treatment on Black Hammock Island and is there Adequate Regulatory Policy to Ensure Integrity?

This project determined if the performance based septic system, proposed for a development on Black Hammock Island in Jacksonville, Florida, is the best choice to prevent environmental contamination from septic tanks and if adequate regulatory policy exists. Research shows a central wastewater treatment plant provides the most efficient pollutant removal but can be cost prohibitive. This project found performance based systems surpasses conventional septic system performance and are more suited and economical to remote areas without sewer service. This project finds current regulations to be inadequate and supports ordinance changes proposed by the Mayor of Jacksonville to enhance the current policy and provide more adequate and meaningful regulation.

Low flow water quality in rivers; septic tank systems and high-resolution phosphorus signals

Rural point sources of phosphorus (P), including septic tank systems, provide a small part of the overall phosphorus budget to surface waters in agricultural catchments but can have a disproportionate impact on the low flow P concentration of receiving rivers. This has particular importance as the discharges are approximately constant into receiving waters and these have restricted dilution capacity during ecologically sensitive summer periods. In this study, a number of identified high impact septic systems were replaced with modern sequential batch reactors in three rural catchments during a monitoring period of 4 years. Sub-hourly P monitoring was conducted using bankside-analysers. Results show that strategic replacement of defective septic tank systems with modern systems and polishing filters decreased the low flow P concentration of one catchment stream by 0.032 mg TP L- 1 (0.018 mg TRP L- 1) over the 4 years. However two of the catchment mitigation efforts were offset by continued new-builds that increased the density of septic systems from 3.4 km- 2 to 4.6 km- 2 and 13.8 km- 2 to 17.2 km- 2 and subsequently increased low flow P concentrations. Future considerations for septic system mitigation should include catchment carrying capacity as well as technology changes.

Efffluent flux prediction in variably saturated soil zones within a septic tank-soil absorption trench

The treatment and hydraulic mechanisms in a septic tank-soil absorption system ( SAS) are highly influenced by the clogging layer or biomat zone which develops on bottom and lower sidewall surfaces within the trench. Flow rates through the biomat and sub-biomat zones are governed largely by the biomat hydraulic properties (resistance and hydraulic conductivity) and the unsaturated hydraulic conductivity of the underlying soil. One- and 2-dimensional models were used to investigate the relative importance of sidewall and vertical flow rates and pathways in SAS. Results of 1-dimensional modelling show that several orders of magnitude variation in saturated hydraulic conductivity (Ks) reduce to a 1 order of magnitude variation in long-term flow rates. To increase the reliability of prediction of septic trench hydrology, HYDRUS-2D was used to model 2-dimensional flow. In the permeable soils, under high trench loading, effluent preferentially flowed in the upper region of the trench where no resistant biomat was present (the exfiltration zone). By comparison, flow was more evenly partitioned between the biomat zones and the exfiltration zones of the low permeability soil. An increase in effluent infiltration corresponded with a greater availability of exfiltration zone, rather than a lower resistance of biomat. Results of modelling simulations demonstrated the important role that a permeable A horizon may play in limiting surface surcharge of effluent under high trench hydraulic loading.

Long-term flow rates and biomat zone hydrology in soil columns receiving septic tank effluent

Soil absorption systems (SAS) are used commonly to treat and disperse septic tank effluent (STE). SAS can hydraulically fail as a result of the low permeable biomat zone that develops on the infiltrative surface. The objectives of this experiment were to compare the hydraulic properties of biomats grown in soils of different textures, to investigate the long-term acceptance rates (LTAR) from prolonged application of STE, and to assess if soils were of major importance in determining LTAR. The STE was applied to repacked sand, Oxisol and Vertisol soil columns over a period of 16 months, at equivalent hydraulic loading rates of 50, 35 and 8 L/m(2)/d, respectively Infiltration rates, soil matric potentials, and biomat hydraulic properties were measured either directly from the soil columns or calculated using established soil physics theory. Biomats 1 to 2 cm thick developed in all soils columns with hydraulic resistances of 27 to 39 d. These biomats reduced a 4 order of magnitude variation in saturated hydraulic conductivity (K.) between the soils to a one order of magnitude variation in LTAR. A relationship between biomat resistance and organic loading rate was observed in all soils. Saturated hydraulic conductivity influenced the rate and extent of biomat development. However, once the biomat was established, the LTAR was governed by the resistance of the biomat and the sub-biomat soil unsaturated flow regime induced by the biomat. Results show that whilst initial soil K. is likely to be important in the establishment of the biomat zone in a trench, LTAR is determined by the biomat resistance and the unsaturated soil hydraulic conductivity, not the K, of a soil. The results call into question the commonly used approach of basing the LTAR, and ultimately trench length in SAS, on the initial K, of soils. (c) 2006 Elsevier Ltd. All rights reserved.

Incorporação de lodo de esgoto na massa cerâmica para fabricação de tijolos maciços: uma alternativa para a disposição final de resíduo

The disposal of sewage sludge is a growing problem face up to management of sanitary sevices. Otherwise, because its making process characteristic, the Ceramic Industry can tolerate the presence of this wastes as raw material. This study has as object to confirm the use of the sewage sluge in the Ceramic Industry like a sustentable alternative for its disposal. Futhermore, this study quests to evaluate the maximum proportion for incorporation of sludge wich result in technically and enviromentally suitable bricks. For found this proportion, the research consisted of (1) making of bricks in full scale, adde up 0%, 5%,10%, 15%, 20%, 25%,30%, 35% e 40% sludge, with size 220x105x45 mm, hand-molded by rammer and baked by industrial kiln; and (2) tecnical and enviromental evaluation of this bricks, according to Brazilian norms. The raw material uses were two distinct clays come from Goianinha/RN and sewage comes from a septic system tank and pumped into tank vehicle, of Natal/RN. The technical evaluation allowed to conclude the addiotion of the sludge brings about signifcant lost of mass and the water absorption grew up according to increase of sludge: every sludge-amended clay bricks absorved more water than control group. Thus, the compressive strength was signicantly decreased because the increase of sludge: bricks with 5% sludge added lost 45% of strength achieved at control group; the bricks made with 10 and 20% lost almost 70% of bigger strength. With up to 25% sludge added to the bricks, the streght decreased over 90%. Concerning heavy metal leaching, the two maximum proportion wich have tecnical approval, it means bricks sludge added with 15 and 20%, can say there is no risk of enviromental contamination using those bricks. This way, in this work context, it can to conclude the maximum proportion atends the technical and enviromental criterion is 20%

Surviving Sepsis Campaign: international guidelines for management of severe sepsis and septic shock: 2008.

OBJECTIVE: To provide an update to the original Surviving Sepsis Campaign clinical management guidelines, "Surviving Sepsis Campaign Guidelines for Management of Severe Sepsis and Septic Shock," published in 2004. DESIGN: Modified Delphi method with a consensus conference of 55 international experts, several subsequent meetings of subgroups and key individuals, teleconferences, and electronic-based discussion among subgroups and among the entire committee. This process was conducted independently of any industry funding. METHODS: We used the Grades of Recommendation, Assessment, Development and Evaluation (GRADE) system to guide assessment of quality of evidence from high (A) to very low (D) and to determine the strength of recommendations. A strong recommendation (1) indicates that an intervention's desirable effects clearly outweigh its undesirable effects (risk, burden, cost) or clearly do not. Weak recommendations (2) indicate that the tradeoff between desirable and undesirable effects is less clear. The grade of strong or weak is considered of greater clinical importance than a difference in letter level of quality of evidence. In areas without complete agreement, a formal process of resolution was developed and applied. Recommendations are grouped into those directly targeting severe sepsis, recommendations targeting general care of the critically ill patient that are considered high priority in severe sepsis, and pediatric considerations. RESULTS: Key recommendations, listed by category, include early goal-directed resuscitation of the septic patient during the first 6 hrs after recognition (1C); blood cultures before antibiotic therapy (1C); imaging studies performed promptly to confirm potential source of infection (1C); administration of broad-spectrum antibiotic therapy within 1 hr of diagnosis of septic shock (1B) and severe sepsis without septic shock (1D); reassessment of antibiotic therapy with microbiology and clinical data to narrow coverage, when appropriate (1C); a usual 7-10 days of antibiotic therapy guided by clinical response (1D); source control with attention to the balance of risks and benefits of the chosen method (1C); administration of either crystalloid or colloid fluid resuscitation (1B); fluid challenge to restore mean circulating filling pressure (1C); reduction in rate of fluid administration with rising filing pressures and no improvement in tissue perfusion (1D); vasopressor preference for norepinephrine or dopamine to maintain an initial target of mean arterial pressure > or = 65 mm Hg (1C); dobutamine inotropic therapy when cardiac output remains low despite fluid resuscitation and combined inotropic/vasopressor therapy (1C); stress-dose steroid therapy given only in septic shock after blood pressure is identified to be poorly responsive to fluid and vasopressor therapy (2C); recombinant activated protein C in patients with severe sepsis and clinical assessment of high risk for death (2B except 2C for postoperative patients). In the absence of tissue hypoperfusion, coronary artery disease, or acute hemorrhage, target a hemoglobin of 7-9 g/dL (1B); a low tidal volume (1B) and limitation of inspiratory plateau pressure strategy (1C) for acute lung injury (ALI)/acute respiratory distress syndrome (ARDS); application of at least a minimal amount of positive end-expiratory pressure in acute lung injury (1C); head of bed elevation in mechanically ventilated patients unless contraindicated (1B); avoiding routine use of pulmonary artery catheters in ALI/ARDS (1A); to decrease days of mechanical ventilation and ICU length of stay, a conservative fluid strategy for patients with established ALI/ARDS who are not in shock (1C); protocols for weaning and sedation/analgesia (1B); using either intermittent bolus sedation or continuous infusion sedation with daily interruptions or lightening (1B); avoidance of neuromuscular blockers, if at all possible (1B); institution of glycemic control (1B), targeting a blood glucose < 150 mg/dL after initial stabilization (2C); equivalency of continuous veno-veno hemofiltration or intermittent hemodialysis (2B); prophylaxis for deep vein thrombosis (1A); use of stress ulcer prophylaxis to prevent upper gastrointestinal bleeding using H2 blockers (1A) or proton pump inhibitors (1B); and consideration of limitation of support where appropriate (1D). Recommendations specific to pediatric severe sepsis include greater use of physical examination therapeutic end points (2C); dopamine as the first drug of choice for hypotension (2C); steroids only in children with suspected or proven adrenal insufficiency (2C); and a recommendation against the use of recombinant activated protein C in children (1B). CONCLUSIONS: There was strong agreement among a large cohort of international experts regarding many level 1 recommendations for the best current care of patients with severe sepsis. Evidenced-based recommendations regarding the acute management of sepsis and septic shock are the first step toward improved outcomes for this important group of critically ill patients.

Studies on the exaggerated inflammatory response caused by streptococcus suis at systemic and central nervous system levels

Streptococcus suis de type 2 est un microorganisme pathogène d’importance chez le porc. Il est la cause de différentes pathologies ayant comme caractéristique commune la méningite. C’est également un agent émergeant de zoonose : des cas cliniques humains ont récemment été rapportés en Asie. Cependant, la pathogénèse de S. suis n’est pas encore complètement élucidée. Jusqu’à présent, la réponse pro-inflammatoire initiée par S. suis n’a été étudiée qu’in vitro. L’étude du choc septique et de la méningite requiert toujours des modèles expérimentaux appropriés. Au cours de cette étude, nous avons développé un modèle in vivo d’infection chez la souris qui utilise la voie d’inoculation intra-péritonéale. Ce modèle a servi à l’étude de la réponse pro-inflammatoire associée à ce pathogène, tant au niveau systémique qu’au niveau du système nerveux central (SNC). Il nous a également permis de déterminer si la sensibilité aux infections à S. suis pouvait être influencée par des prédispositions génétiques de l’hôte. Le modèle d’infection par S. suis a été mis au point sur des souris de lignée CD1. Les résultats ont démontré une bactériémie élevée pendant les trois jours suivant l’infection. Celle-ci était accompagnée d’une libération rapide et importante de différentes cytokines pro-inflammatoires (TNF-α, IL-6, IL-12p40/p70, IFN-ɣ) et de chémokines (KC, MCP-1 and RANTES), qui ont entraîné un choc septique et la mort de 20 % des animaux. Ensuite, pour confirmer le rôle de l’inflammation sur la mortalité et pour déterminer si les caractéristiques génétiques de l’hôte pouvaient influencer la réponse inflammatoire et l’issue de la maladie, le modèle d’infection a été étendu à deux lignées murines consanguines différentes considérées comme résistante : la lignée C57BL/6 (B6), et sensible : la lignée A/J. Les résultats ont démontré une importante différence de sensibilité entre les souris A/J et les souris B6, avec un taux de mortalité atteignant 100 % à 20 h post-infection (p.i.) pour la première lignée et de seulement 16 % à 36 h p.i. pour la seconde. La quantité de bactéries dans le sang et dans les organes internes était similaire pour les deux lignées. Donc, tout comme dans la lignée CD1, la bactériémie ne semblait pas être liée à la mort des souris. La différence entre les taux de mortalité a été attribuée à un choc septique non contrôlé chez les souris A/J infectées par S. suis. Les souris A/J présentaient des taux exceptionnellement élevés de TNF-α, IL-12p40/p70, IL-1β and IFN- γ, significativement supérieurs à ceux retrouvés dans la lignée B6. Par contre, les niveaux de chémokines étaient similaires entre les lignées, ce qui suggère que leur influence est limitée dans le développement du choc septique dû à S. suis. Les souris B6 avaient une production plus élevée d’IL-10, une cytokine anti-inflammatoire, ce qui suppose que la cascade cytokinaire pro-inflammatoire était mieux contrôlée, entraînant un meilleur taux de survie. Le rôle bénéfique potentiel de l’IL-10 chez les souris infectées par S. suis a été confirmé par deux approches : d’une part en bloquant chez les souris B6 le récepteur cellulaire à l’IL-10 (IL-10R) par un anticorps monoclonal anti-IL-10R de souris et d’autre part en complémentant les souris A/J avec de l’IL-10 de souris recombinante. Les souris B6 ayant reçu le anticorps monoclonal anti-IL-10R avant d’être infectées par S. suis ont développé des signes cliniques aigus similaires à ceux observés chez les souris A/J, avec une mortalité rapide et élevée et des taux de TNF-α plus élevés que les souris infectées non traitées. Chez les souris A/J infectées par S. suis, le traitement avec l’IL-10 de souris recombinante a significativement retardé l’apparition du choc septique. Ces résultats montrent que la survie au choc septique dû à S. suis implique un contrôle très précis des mécanismes pro- et anti-inflammatoires et que la réponse anti-inflammatoire doit être activée simultanément ou très rapidement après le début de la réponse pro-inflammatoire. Grâce à ces expériences, nous avons donc fait un premier pas dans l’identification de gènes associés à la résistance envers S. suis chez l’hôte. Une des réussites les plus importantes du modèle d’infection de la souris décrit dans ce projet est le fait que les souris CD1 ayant survécu à la septicémie présentaient dès 4 jours p.i. des signes cliniques neurologiques clairs et un syndrome vestibulaire relativement similaires à ceux observés lors de méningite à S. suis chez le porc et chez l’homme. L’analyse par hybridation in situ combinée à de l’immunohistochimie des cerveaux des souris CD1 infectées a montré que la réponse inflammatoire du SNC débutait avec une augmentation significative de la transcription du Toll-like receptor (TLR)2 et du CD14 dans les microvaisseaux cérébraux et dans les plexus choroïdes, ce qui suggère que S. suis pourrait se servir de ces structures comme portes d’entrée vers le cerveau. Aussi, le NF-κB (suivi par le système rapporteur de l’activation transcriptionnelle de IκBα), le TNF-α, l’IL-1β et le MCP-1 ont été activés, principalement dans des cellules identifiées comme de la microglie et dans une moindre mesure comme des astrocytes. Cette activation a également été observée dans différentes structures du cerveau, principalement le cortex cérébral, le corps calleux, l’hippocampe, les plexus choroïdes, le thalamus, l’hypothalamus et les méninges. Partout, cette réaction pro-inflammatoire était accompagnée de zones extensives d’inflammation et de nécrose, de démyélinisation sévère et de la présence d’antigènes de S. suis dans la microglie. Nous avons mené ensuite des études in vitro pour mieux comprendre l’interaction entre S. suis et la microglie. Pour cela, nous avons infecté des cellules microgliales de souris avec la souche sauvage virulente (WT) de S. suis, ainsi qu’avec deux mutants isogéniques, un pour la capsule (CPS) et un autre pour la production d’hémolysine (suilysine). Nos résultats ont montré que la capsule était un important mécanisme de résistance à la phagocytose pour S. suis et qu’elle modulait la réponse inflammatoire, en dissimulant les composants pro-inflammatoires de la paroi bactérienne. Par contre, l’absence d’hémolysine, qui est un facteur cytotoxique potentiel, n’a pas eu d’impact majeur sur l’interaction de S. suis avec la microglie. Ces études sur les cellules microgliales ont permis de confirmer les résultats obtenus précédemment in vivo. La souche WT a induit une régulation à la hausse du TLR2 ainsi que la production de plusieurs médiateurs pro-inflammatoires, dont le TNF-α et le MCP-1. S. suis a induit la translocation du NF-kB. Cet effet était plus rapide dans les cellules stimulées par le mutant déficient en CPS, ce qui suggère que les composants de la paroi cellulaire représentent de puissants inducteurs du NF-kB. De plus, la souche S. suis WT a stimulé l’expression de la phosphotyrosine, de la PKC et de différentes cascades liées à l’enzyme mitogen-activated protein kinase (MAPK). Cependant, les cellules microgliales infectées par le mutant déficient en CPS ont montré des profils de phosphorylation plus forts et plus soutenus que celles infectées par le WT. Finalement, la capsule a aussi modulé l’expression de l’oxyde nitrique synthétase inductible (iNOS) induite par S. suis et par la production subséquente d’oxyde nitrique par la microglie. Ceci pourrait être lié in vivo à la neurotoxicité et à la vasodilatation. Nous pensons que ces résultats contribueront à une meilleure compréhension des mécanismes sous-tendant l’induction de l’inflammation par S. suis, ce qui devrait permettre, d’établir éventuellement des stratégies plus efficaces de lutte contre la septicémie et la méningite. Enfin, nous pensons que ce modèle expérimental d’infection chez la souris pourra être utilisé dans l’étude de la pathogénèse d’autres bactéries ayant le SNC pour cible.

The water quality of the River Enborne, UK: observations from high-frequency Monitoring in a rural, lowland river system

This paper reports the results of a 2-year study of water quality in the River Enborne, a rural river in lowland England. Concentrations of nitrogen and phosphorus species and other chemical determinands were monitored both at high-frequency (hourly), using automated in situ instrumentation, and by manual weekly sampling and laboratory analysis. The catchment land use is largely agricultural, with a population density of 123 persons km−2. The river water is largely derived from calcareous groundwater, and there are high nitrogen and phosphorus concentrations. Agricultural fertiliser is the dominant source of annual loads of both nitrogen and phosphorus. However, the data show that sewage effluent discharges have a disproportionate effect on the river nitrogen and phosphorus dynamics. At least 38% of the catchment population use septic tank systems, but the effects are hard to quantify as only 6% are officially registered, and the characteristics of the others are unknown. Only 4% of the phosphorus input and 9% of the nitrogen input is exported from the catchment by the river, highlighting the importance of catchment process understanding in predicting nutrient concentrations. High-frequency monitoring will be a key to developing this vital process understanding.

Septic Shock, Necrotizing Pneumonitis, and Meningoencephalitis Caused by Mycoplasma pneumoniae in a Child: A Case Report

Mycoplasma pneumoniae is an important causative agent of respiratory infection in childhood. Although the infection caused by M. pneumoniae is classically described as benign, severe and life-threatening pulmonary and extrapulmonary complications can occur. This study describes the first case of septic shock related to M. pneumoniae in a child with necrotizing pneumonitis, severe encephalitis, and multiple organs involvement, with a favorable outcome after lobectomy and systemic corticosteroids

Contact system activation in human sepsis - 47kD HK, a marker of sepsis severity?

AIM: This pilot study seeks to determine whether contact system activation (CSA) occurs in human sepsis patients and to characterise blood levels of the 47kD light chain of high-molecular weight kininogen (47kD HK). METHODS: Six consecutive patients with clinical suspicion of sepsis were evaluated on days 1, 2, 3 and 6-8 for 47kD HK blood levels expressed in U/ml of whole blood and as percent of total HK. 47kD HK was measured in whole blood by quantitative immunoblot analysis. RESULTS: On study day 1 or 2, analysis of 47kD HK in U/ml of whole blood identified CSA in 3/6 patients.When 47kD HK levels were expressed as percent of total HK, 4/6 patients were identified with CSA before day 3. The degree of CSA as assayed by the presence of 47kD HK correlated with the severity of the systemic inflammatory syndrome (SIRS), i.e. mean CSA increased progressively from basal levels in healthy controls (0.08 U/ml or 10.4%) to patients without SIRS (0.10 U/ml or 15.1%), to patients with sepsis (0.12 U/ml or 15.0%), and finally to patients in a combined category of severe sepsis and septic shock (0.13 U/ml or 17.4%). CONCLUSION: CSA, defined by increased 47kD HK, occurred early on in the course of sepsis in a subset of sepsis patients. 47kD HK levels, an indicator of bradykinin release, correlated with sepsis severity. Future larger studies will need to evaluate the role of 47kD HK as a biomarker for both prognosis and treatment response in human sepsis..

The function of the murine complement *C3a and *C5a anaphylatoxin receptors in endotoxemia, bacteremia and septic shock

The complement system functions as a major effector for both the innate and adaptive immune response. Activation of the complement cascade by either the classical, alternative, or lectin pathway promotes the proteolysis of C3 and C5 thereby generating C3a and C5a. Referred to as anaphylatoxins, the C3a and C5a peptides mediate biological effects upon binding to their respective receptors; C3a binds to the C3a receptor (C3aR) while C5a binds to the C5a receptor (C5aR, CD88). Both C3a and C5a are known for their broad proinflammatory effects. Elevated levels of both peptides have been isolated from patients with a variety of inflammatory diseases such as COPD, asthma, RA, SLE, and sepsis. Recent studies suggest that C5a is a critical component in the acquired neutrophil dysfunction, coagulopathy, and progressive multi-organ dysfunction characteristic of sepsis. The primary hypothesis of this dissertation was that preventing C3a-C3aR and C5a-C5aR mediated pro-inflammatory effects would improve survival in endotoxic, bacteremic and septic shock. To test this hypothesis, the murine C3aR and C5aR genes were disrupted. Following disruption of both the C3aR and C5aR genes, no abnormalities were identified other than the absence of their respective mRNA and protein. In models of both endotoxic and bacteremic shock, C3aR deficient mice suffered increased mortality when compared to their wild type littermates. C3aR deficient mice also had elevated circulating IL-1β levels. Using a model of sepsis, C3aR deficient mice had a higher circulating concentration of IL-6 and decreased peritoneal inflammatory infiltration. While these results were unexpected, they support an emerging role for C3a in immunomodulation. In contrast, following endotoxic or bacteremic shock, C5aR deficient mice experienced increased survival, less hemoconcentration and less thrombocytopenia. It was later determined that C5a mediated histamine release significantly contributes to host morbidity and mortality in bacteremic shock. These studies provide evidence that C5a functions primarily as a proinflammatory molecule in models of endotoxic and bacteremic shock. In the same models, C3a-C3aR interactions suppress the inflammatory response and protect the host. Collectively, these results present in vivo evidence that C3a and C5a have divergent biological functions. ^

Evaluation of semi-passive treatment technologies for septic lagoon capacity expansion

In Canada, increases in rural development has led to a growing need to effectively manage the resulting municipal and city sewage without the addition of significant cost- and energy- expending infrastructure. Storring Septic Service Limited is a family-owned, licensed wastewater treatment facility located in eastern Ontario. It makes use of a passive waste stabilization pond system to treat and dispose of waste and wastewater in an environmentally responsible manner. Storring Septic, like many other similar small-scale wastewater treatment facilities across Canada, has the potential to act as a sustainable eco-engineered facility that municipalities and service providers could utilize to manage and dispose of their wastewater. However, it is of concern that the substantial inclusion of third party material could be detrimental to the stability and robustness of the pond system. In order to augment the capacity of the current facility, and ensure it remains a self-sustaining system with the capacity to safely accept septage from other sewage haulers, it was hypothesized that pond effluent treatment could be further enhanced through the incorporation of one of three different technology solutions, which would allow the reduction of wastewater quality parameters below existing regulatory effluent discharge limits put in place by Ontario’s Ministry of the Environment and Climate Change (MOECC). Two of these solutions make use of biofilm technologies in order to enhance the removal of wastewater parameters of interest, and the third utilizes the natural water filtration capabilities of zebra mussels. Pilot-scale testing investigated the effects of each of these technologies on treatment performance under both cold and warm weather operation. This research aimed to understand the important mechanisms behind biological filtration methods in order to choose and optimize the best treatment strategy for full-scale testing and implementation. In doing so, a recommendation matrix was elaborated provided with the potential to be used as a universal operational strategy for wastewater treatment facilities located in environments of similar climate and ecology.

Process, performance, and pollution potential: A review of septic tank-soil absorption systems

On-site wastewater treatment and dispersal systems (OWTS) are used in non-sewered populated areas in Australia to treat and dispose of household wastewater. The most common OWTS in Australia is the septic tank-soil absorption system (SAS) - which relies on the soil to treat and disperse effluent. The mechanisms governing purification and hydraulic performance of a SAS are complex and have been shown to be highly influenced by the biological zone (biomat) which develops on the soil surface within the trench or bed. Studies suggest that removal mechanisms in the biomat zone, primarily adsorption and filtering, are important processes in the overall purification abilities of a SAS. There is growing concern that poorly functioning OWTS are impacting upon the environment, although to date, only a few investigations have been able to demonstrate pollution of waterways by on-site systems. In this paper we review some key hydrological and biogeochemical mechanisms in SAS, and the processes leading to hydraulic failure. The nutrient and pathogen removal efficiencies in soil absorption systems are also reviewed, and a critical discussion of the evidence of failure and environmental and public health impacts arising from SAS operation is presented. Future research areas identified from the review include the interactions between hydraulic and treatment mechanisms, and the biomat and sub-biomat zone gas composition and its role in effluent treatment.

Prediction of steady-state flux through variably saturated zones within a septic absorption trench

This paper describes effluent flow dynamics within a septic absorption system and the prediction of flow through the biomat and sub-biomat zone. Using soil hydraulic properties in a one dimensional model we demonstrate how soil hydraulic properties interact with biomat resistances to determine long-term acceptance rate (LTAR). The LTAR is a key parameter used in the Australian and New Zealand Standard AS1547:2000 to calculate the area of trench required to ensure trenches are not overloaded. Results show that several orders of magnitude variation in saturated hydraulic conductivity (Ks) collapse to a one order of magnitude variation in LTAR. These results are calculated from a model using basic flow theory, allowing LTAR to be estimated for any combination of biomat resistance and soil hydraulic properties. To increase the reliability of prediction of septic trench hydrology, HYDRUS 2D was used to model two dimensional flow. For more permeable soils, the exfiltration zone above sidewall biomat growth is shown to be a key pathway for excess effluent flow.

Mediators of gram-positive septic shock

Septic shock can occur as a result of Gram-negative or Gram-positive infection and involves a complex interaction between bacterial factors and the host immune system producing a systemic inflammatory state that may progress to multiple organ failure and death. Gram-positive bacteria are increasingly becoming more prevalent especially Staphylococcus epidermidis in association with indwelling devices. Lipopolysaccaride (LPS) is the key Gram-negative component involved in this process, but it is not clear which components of Gram-positive bacteria are responsible for progression of this often fatal disease. The aim of this thesis was to investigate the effect of bacterial components on the immune systems. Lipid S, a short chain form of lipoteichoic acid (LTA) found to be excreted from bacteria during growth in culture medium was examined along with other Gram-positive cell wall components: LTA, peptidoglycan (PG) and wall teichoic acids (WTA) and LPS from Gram-negative bacteria. Lipid S, LTA, PG and LPS but not WTA all stimulated murine macrophages and cell lines to produce significant amounts of NO, TNF-a, IL-6 and IL-1 and would induce fever and tissue damage seen in inflammatory diseases. Lipid S proved to be the most potent out of the Gram-positive samples tested. IgG antibodies in patients serum were found to bind to and cross react with lipid S and LTA. Anti-inflammatory antibiotics, platelet activating factor (PAF), PAF receptor antagonists and monoclonal antibodies (mAbs) directed to LTA, CD14 and toll-like receptors were utilised to modulate cytokine and NO production. In cell culture the anti-LTA and the anti-CD14 mAbs failed to markedly attenuate the production of NO, TNF-a, IL-6 or IL-1, the anti-TLR4 antibody did greatly inhibit the ability of LPS to stimulate cytokine production but not lipid S. The tetracyclines proved to be the most effective compounds, many were active at low concentrations and showed efficacy to inhibit both lipid S and LPS stimulated macrophages to produce NO.