Engine performance characteristics for biodiesels of different degrees of saturation and carbon chain lengths

This experimental study examines the effect on performance and emission outputs of a compression ignition engine operating on biodiesels of varying carbon chain length and the degree of unsaturation. A well-instrumented, heavy-duty, multi-cylinder, common-rail, turbo-charged diesel engine was used to ensure that the results contribute in a realistic way to the ongoing debate about the impact of biofuels. Comparative measurements are reported for engine performance as well as the emissions of NOx, particle number and size distribution, and the concentration of the reactive oxygen species (which provide a measure of the toxicity of emitted particles). It is shown that the biodiesels used in this study produce lower mean effective pressure, somewhat proportionally with their lower calorific values; however, the molecular structure has been shown to have little impact on the performance of the engine. The peak in-cylinder pressure is lower for the biodiesels that produce a smaller number of emitted particles, compared to fossil diesel, but the concentration of the reactive oxygen species is significantly higher because of oxygen in the fuels. The differences in the physicochemical properties amongst the biofuels and the fossil diesel significantly affect the engine combustion and emission characteristics. Saturated short chain length fatty acid methyl esters are found to enhance combustion efficiency, reduce NOx and particle number concentration, but results in high levels of fuel consumption.

An improved procedure for obtaining and maintaining well characterized partial water saturation states on concrete samples to be used for mass transport tests

A conditioning procedure is proposed allowing to install into the concrete specimens any selected value of water saturation degree with homogeneous moisture distribution. This is achieved within the least time and the minimum alteration of the concrete specimens. The protocol has the following steps: obtaining basic drying data at 50 °C (water absorption capacity and drying curves); unidirectional drying of the specimens at 50 °C until reaching the target saturation degree values; redistribution phase in closed containers at 50 °C (with measurement of the quasi-equilibrium relative humidities); storage into controlled environment chambers until and during mass transport tests, if necessary. A water transport model is used to derive transport parameters of the tested materials from the drying data, i.e., relative permeabilities and apparent water diffusion coefficients. The model also allows calculating moisture profiles during isothermal drying and redistribution phases, thus allowing optimization of the redistribution times for obtaining homogeneous moisture distributions.

Influential Factors of Loess Liquefaction and Pore Pressure Development

The liquefaction of loess under dynamic loading is studied experimentally with a dynamic triaxial test system. The effects of over-consolidation ratio (OCR), saturation degree and the frequency of dynamic loading upon loess liquefaction are investigated. The development of pore pressure within loess samples is also discussed. Based on the experimental results, the empirical relationship between pore pressure ratio and loading cycle number ratio is established for normal consolidated saturated loess.

Adaptive automated construction of hybrid heuristics for exam timetabling and graph colouring problems

In this paper, we present a random iterative graph based hyper-heuristic to produce a collection of heuristic sequences to construct solutions of different quality. These heuristic sequences can be seen as dynamic hybridisations of different graph colouring heuristics that construct solutions step by step. Based on these sequences, we statistically analyse the way in which graph colouring heuristics are automatically hybridised. This, to our knowledge, represents a new direction in hyper-heuristic research. It is observed that spending the search effort on hybridising Largest Weighted Degree with Saturation Degree at the early stage of solution construction tends to generate high quality solutions. Based on these observations, an iterative hybrid approach is developed to adaptively hybridise these two graph colouring heuristics at different stages of solution construction. The overall aim here is to automate the heuristic design process, which draws upon an emerging research theme on developing computer methods to design and adapt heuristics automatically. Experimental results on benchmark exam timetabling and graph colouring problems demonstrate the effectiveness and generality of this adaptive hybrid approach compared with previous methods on automatically generating and adapting heuristics. Indeed, we also show that the approach is competitive with the state of the art human produced methods.

Adaptive linear combination of heuristic orderings in constructing examination timetables

In this paper, we investigate adaptive linear combinations of graph coloring heuristics with a heuristic modifier to address the examination timetabling problem. We invoke a normalisation strategy for each parameter in order to generalise the specific problem data. Two graph coloring heuristics were used in this study (largest degree and saturation degree). A score for the difficulty of assigning each examination was obtained from an adaptive linear combination of these two heuristics and examinations in the list were ordered based on this value. The examinations with the score value representing the higher difficulty were chosen for scheduling based on two strategies. We tested for single and multiple heuristics with and without a heuristic modifier with different combinations of weight values for each parameter on the Toronto and ITC2007 benchmark data sets. We observed that the combination of multiple heuristics with a heuristic modifier offers an effective way to obtain good solution quality. Experimental results demonstrate that our approach delivers promising results. We conclude that this adaptive linear combination of heuristics is a highly effective method and simple to implement.

Influence of calcium ion deposition on apatite-inducing ability of porous titanium for biomedical applications

In the present study, the influence of calcium ion deposition on the apatite-inducing ability of porous titanium(Ti) was investigated in a modified simulated body fluid (m-SBF). Calcium hydroxide (Ca(OH)₂) solutions with five degrees of saturation were used to hydrothermally deposit Ca ions on porous Ti with a porosity of 80%. Apatite-inducing ability of the Ca-ion-deposited porous Ti was evaluated by soaking them in m-SBF for up to 14 days. Scanning electron microscopy (SEM) and X-ray diffractometry (XRD) confirmed that a thin layer of calcium titanate (CaTiO₃)/calcium oxide (CaO) mixture with a nanostructured porous network was produced on porous Ti substrates after hydrothermal treatment at 200 °C for 8 h. X-ray photoelectron spectroscopy results demonstrated that the content of the Ca ions deposited on Ti and the thickness of the CaTiO₃/CaO layer increased with increasing saturation degree of the Ca(OH)₂ solution. The thickest (over 10 nm) CaTiO₃/CaO layer with the highest Ca content was achieved on the Ti treated in an oversaturated Ca(OH)₂ solution (0.2 M). SEM, XRD, transmission electron microscopy and Fourier transformed infrared spectroscopy analysis indicated that the porous Ti samples deposited with the highest content of Ca ions exhibited the best apatite-inducing ability, producing a dense and complete carbonated apatite coating after a 14 day soaking in m-SBF. The present study illustrated the validity of using Ca ion deposition as a pre-treatment to endow desirable apatite-inducing ability of porous Ti for bone tissue engineering applications.

Esterco bovino e calagem para formação de mudas de guanandi

O objetivo deste trabalho foi avaliar, em casa de vegetação, os efeitos de doses de esterco bovino e de calcário na formação de mudas de guanandi (Calophyllum brasiliense Cambèss.). Foram avaliadas quatro doses de cada fator, combinadas em esquema fatorial 4x4. O delineamento experimental foi inteiramente ao acaso com quatro repetições, e cada parcela continha cinco mudas. O substrato foi formado pela mistura, em volume, de oito partes de subsolo e duas partes de areia, e doses de esterco correspondentes a 0, 2, 4 e 6 partes que, em massa, equivalem a 0, 101, 175 e 229 kg m-3. As doses de calcário foram calculadas para elevar a saturação por bases (V%) a 20, 35, 50 e 65%. Aos 120 dias, foram avaliados: altura, diâmetro do colo, número de folhas, área foliar e matéria seca das partes aérea e radicular das mudas. em substrato constituído de subsolo+areia, a calagem e a adubação com esterco bovino não são necessárias para produção de mudas de guanandi.

Nível crítico de fósforo no solo paraPanicum maximum Jacq. cv. Tanzânia

Foram avaliados os efeitos da aplicação de fósforo (P) em solo argiloso, de textura média e arenoso, sobre a produção de matéria seca de Panicum maximum Jacq. cv. Tanzânia. O ensaio foi conduzido em casa de vegetação, em vasos de plástico contendo 10 dm³ de solo, em esquema fatorial e delineamento inteiramente ao acaso. Após calagem para V = 70% e aplicação de 0, 35, 70, 105 e 140 mg/dm³ de P, o solo foi umedecido, e depois de 30 dias, secado e amostrado. O ensaio foi conduzido por 76 dias, a partir da emergência das plântulas, com o primeiro corte aos 48 dias, a 10 cm do solo, e o segundo, aos 76,rente ao solo. Com a aplicação de P houve aumento de produção de matéria seca, e o maior acréscimo ocorreu com a aplicação de 35 mg/dm³. A maior produção foi obtida no solo de textura média. O teor de P nas plantas estava adequado nos solos arenoso e argiloso. No de textura média, ele diminuiu com o aumento da produção,caracterizando efeito de diluição. Com aprodução relativa e o teor de P de cada solo, foi determinado o nível crítico de 38 mg/dm³ de P extraído por resina.

The relationship between pasture degradation and soil properties in the Brazilian amazon: a case study

Pasture degradation is one of the greatest problems related to land use in the Amazon region, forcing farmers to open new forest areas. Many studies have identified the causes and the factors involved in this degradation process, in an attempt to reverse the situation. The purpose of this study was to examine the relationship between pasture degradation and some soil properties, to try to identify the most significant soil features in the degradation process. A cattle raising farm in the eastern Amazon region, with pastures of different ages and degrees of degradation, was used as the site for this study: a primary forest area, PN; three Guinea grass (Panicum maximum Jacq.) pastures in an increasingly degraded sequence-P1, P2 and P3; one Gamba grass (Andropogon gayanus Kunth) pasture following an extremely degraded Guinea grass pasture, P4. Aboveground phytomass data showed differences between the pastures, reflecting initially observed degradation levels. Grass biomass decreased sharply from P1 to P2 and disappeared at P3. Pasture recovery with Gamba grass at P4 was very successful, with grass biomass higher than P1 and weed biomass smaller than P2 and P3. Root biomass also decreased with pasture degradation. Soil bulk density increased with pasture decrease at the topsoil layer. Results from the soil chemical analysis showed that there were no signs of decrease in organic carbon and total nitrogen after the forest was transformed into pasture. In all pastures, degraded or not, the soil pH, the sum of bases and the saturation degree were higher than in the forest soil. The extractable phosphorus content, lower in forest soil, remained quite stable in pasture soils, but it could become a limiting factor for the maintenance of Guinea grass. Results indicated that pasture degradation does not seem to be directly related to the modification of the chemical features of soils. (C) 2004 Elsevier B.V. All rights reserved.

Esterco bovino para o desenvolvimento inicial de plantas provenientes de quatro matrizes de Corymbia citriodora

This work aimed to evaluate the effect of cattle manure levels in the phase of implementation Corymbia citriodora (Hook.) K. D. Hill & L. A. S. Johnson (Eucalyptus citriodora) seedlings in field, produced from seeds collected from four mother trees. The experiment was carried out in green house, in pots filled with 5 dm 3 of Oxisol. Five cattle manure levels were applied 0, 10, 20, 30, and 40 t ha -1 (0, 25, 50, 75, and 100 g pot -1). All treatments received lime levels which were calculated to increase the base saturation degree to 50%. The soil fertility was evaluated after 30 days of soil incubation with manure and lime. The seeds were collected from mother trees called 2, 8, 20 and 29. Sowing was performed directly in rigid plastic containers of 50 cm 3 and seedlings were transplanted when they were around 17 cm height. The experimental design was entirely randomized, in a factorial 5 × 4 (five doses of cattle manure and seeds of four mother trees) scheme and four repetitions. Each parcel was a pot with two plants. At 90 days the height, foliar area, stalk diameter, shoot and root dry matter. The plants responded positively to application of manure, but differently for each evaluated growth characteristic linearly or quadratically. The manure levels had linear effects on growth characteristics and dry matter production of the plants from mother trees 2 and 20 moreover these plants require more cattle manure levels than ones from mother trees 8 and 29. The cattle manure promoted the best development of plants from mother trees 8 and 29, in relationship with dry matter production of shoot components was approximately 27 t ha-1, equivalent to 67.5 g pot.

Condutividade hidráulica saturada e direcional em xisto: ensaios em laboratório. -

Pós-graduação em Geociências e Meio Ambiente - IGCE

Atributos químicos e físicos de um argissolo cultivado com Panicum maximum Jacq. cv. IPR-86 Milênio, sob lotação rotacionada e adubado com nitrogênio

A avaliação dos atributos químicos e físicos do solo é necessária em estudos que exploram intensivamente os sistemas de pastejo. No presente trabalho, objetivou-se avaliar as variações nos atributos físicos e químicos de um Argissolo cultivado com capim-milênio, sob pastejo, no intervalo compreendido entre outubro/2001 e maio/2002, no quinto ano de aplicação sucessiva das seguintes doses de N: 0, 150, 300 e 450 kg ha-1. Após os cinco anos de aplicação de 450 kg ha-1 de N, o teor de MO aumentou em 5 g dm-3, o que resultou em aumento da CTC. No período de outubro/2001 a maio/2002 houve diminuição nos valores de pH e de V com a aplicação de N. A densidade do solo variou pouco com a adubação nitrogenada; a percentagem de microporos aumentou e a de macroporos diminuiu na camada de 0-5 cm com o aumento das doses de N, mas a porosidade total permaneceu constante; e a resistência à penetração, quando o solo apresentava 90 g kg-1 de água, não foi afetada pelas doses de N e não foi restritiva ao crescimento das plantas.

Evaluation of Electrical Resistivity in a Tropical Sandy Soil Compacted

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)