Experimental study of strain fields during shearing of medium and high-strength steel sheet

There is a shortage of experimentally determined strains during sheet metal shearing. These kinds of data are a requisite to validate shearing models and to simulate the shearing process. In this work, strain fields were continuously measured during shearing of a medium and a high strength steel sheet, using digital image correlation. Preliminary studies based on finite element simulations, suggested that the effective surface strains are a good approximation of the bulk strains below the surface. The experiments were performed in a symmetric set-up with large stiffness and stable tool clearances, using various combinations of tool clearance and clamping configuration. Due to large deformations, strains were measured from images captured in a series of steps from shearing start to final fracture. Both the Cauchy and Hencky strain measures were considered, but the difference between these were found negligible with the number of increments used (about 20 to 50). Force-displacement curves were also determined for the various experimental conditions. The measured strain fields displayed a thin band of large strain between the tool edges. Shearing with two clamps resulted in a symmetric strain band whereas there was an extended area with large strains around the tool at the unclamped side when shearing with one clamp. Furthermore, one or two cracks were visible on most of the samples close to the tool edges well before final fracture. The fracture strain was larger for the medium strength material compared with the high-strength material and increased with increasing clearance.

A hybrid-mixed finite element formulation for the geometrically exact analysis of three-dimensional framed structures

This paper addresses the development of a hybrid-mixed finite element formulation for the quasi-static geometrically exact analysis of three-dimensional framed structures with linear elastic behavior. The formulation is based on a modified principle of stationary total complementary energy, involving, as independent variables, the generalized vectors of stress-resultants and displacements and, in addition, a set of Lagrange multipliers defined on the element boundaries. The finite element discretization scheme adopted within the framework of the proposed formulation leads to numerical solutions that strongly satisfy the equilibrium differential equations in the elements, as well as the equilibrium boundary conditions. This formulation consists, therefore, in a true equilibrium formulation for large displacements and rotations in space. Furthermore, this formulation is objective, as it ensures invariance of the strain measures under superposed rigid body rotations, and is not affected by the so-called shear-locking phenomenon. Also, the proposed formulation produces numerical solutions which are independent of the path of deformation. To validate and assess the accuracy of the proposed formulation, some benchmark problems are analyzed and their solutions compared with those obtained using the standard two-node displacement/ rotation-based formulation.

Hybrid and multi-field variational principles for geometrically exact three-dimensional beams

This paper addresses the development of several alternative novel hybrid/multi-field variational formulations of the geometrically exact three-dimensional elastostatic beam boundary-value problem. In the framework of the complementary energy-based formulations, a Legendre transformation is used to introduce the complementary energy density in the variational statements as a function of stresses only. The corresponding variational principles are shown to feature stationarity within the framework of the boundary-value problem. Both weak and linearized weak forms of the principles are presented. The main features of the principles are highlighted, giving special emphasis to their relationships from both theoretical and computational standpoints. (C) 2010 Elsevier Ltd. All rights reserved.

Análise não-linear de treliças pelo método dos elementos finitos posicional

This work presents the positional nonlinear geometric formulation for trusses using different strain measures. The positional formulation presents an alternative approach for nonlinear problems. This formulation considers nodal positions as variables of the nonlinear system instead of displacements (widely found in literature). The work also describes the arc-length method used for tracing equilibrium paths with snap-through and snap-back. Numerical applications for trusses already established in the literature and comparisons with other studies are provided to prove the accuracy of the proposed formulation

WYPIWYG Hyperelasticity

In this paper we describe a new promising procedure to model hyperelastic materials from given stress-strain data. The main advantage of the proposed method is that the user does not need to have a relevant knowledge of hyperelasticity, large strains or hyperelastic constitutive modelling. The engineer simply has to prescribe some stress strain experimental data (whether isotropic or anisotropic) in also user prescribed stress and strain measures and the model almost exactly replicates the experimental data. The procedure is based on the piece-wise splines model by Sussman and Bathe and may be easily generalized to transversely isotropic and orthotropic materials. The model is also amenable of efficient finite element implementation. In this paper we briefly describe the general procedure, addressing the advantages and limitations. We give predictions for arbitrary ?experimental data? and also give predictions for actual experiments of the behaviour of living soft tissues. The model may be also implemented in a general purpose finite element program. Since the obtained strain energy functions are analytic piece-wise functions, the constitutive tangent may be readily derived in order to be used for implicit static problems, where the equilibrium iterations must be performed and the material tangent is needed in order to preserve the quadratic rate of convergence of Newton procedures.

Métodos computacionales para visco-hiperelasticidad anisótropa en grandes deformaciones

El comportamiento mecánico de muchos materiales biológicos y poliméricos en grandes deformaciones se puede describir adecuadamente mediante formulaciones isocóricas hiperelásticas y viscoelásticas. Las ecuaciones de comportamiento elástico y viscoelástico y las formulaciones computacionales para materiales incompresibles isótropos en deformaciones finitas están ampliamente desarrolladas en la actualidad. Sin embargo, el desarrollo de modelos anisótropos no lineales y de sus correspondientes formulaciones computacionales sigue siendo un tema de investigación de gran interés. Cuando se consideran grandes deformaciones, existen muchas medidas de deformación disponibles con las que poder formular las ecuaciones de comportamiento. Los modelos en deformaciones cuadráticas facilitan la implementación en códigos de elementos finitos, ya que estas medidas surgen de forma natural en la formulación. No obstante, pueden dificultar la interpretación de los modelos y llevar a resultados pocos realistas. El uso de deformaciones logarítmicas permite el desarrollo de modelos más simples e intuitivos, aunque su formulación computacional debe ser adaptada a las exigencias del programa. Como punto de partida, en esta tesis se demuestra que las deformaciones logarítmicas representan la extensión natural de las deformaciones infinitesimales, tanto axiales como angulares, al campo de las grandes deformaciones. Este hecho permite explicar la simplicidad de las ecuaciones resultantes. Los modelos hiperelásticos predominantes en la actualidad están formulados en invariantes de deformaciones cuadráticas. Estos modelos, ya sean continuos o microestructurales, se caracterizan por tener una forma analítica predefinida. Su expresión definitiva se calcula mediante un ajuste de curvas a datos experimentales. Un modelo que no sigue esta metodología fue desarrollado por Sussman y Bathe. El modelo es sólo válido para isotropía y queda definido por una función de energía interpolada con splines, la cual reproduce los datos experimentales de forma exacta. En esta tesis se presenta su extensión a materiales transversalmente isótropos y ortótropos utilizando deformaciones logarítmicas. Asimismo, se define una nueva propiedad que las funciones de energía anisótropas deben satisfacer para que su convergencia al caso isótropo sea correcta. En visco-hiperelasticidad, aparte de las distintas funciones de energía disponibles, hay dos aproximaciones computational típicas basadas en variables internas. El modelo original de Simó está formulado en tensiones y es válido para materiales anisótropos, aunque sólo es adecuado para pequeñas desviaciones con respecto al equilibrio termodinámico. En cambio, el modelo basado en deformaciones de Reese y Govindjee permite grandes deformaciones no equilibradas pero es, en esencia, isótropo. Las formulaciones anisótropas en este último contexto son microestructurales y emplean el modelo isótropo para cada uno de los constituyentes. En esta tesis se presentan dos formulaciones fenomenológicas viscoelásticas definidas mediante funciones hiperelásticas anisótropas y válidas para grandes desviaciones con respecto al equilibrio termodinámico. El primero de los modelos está basado en la descomposición multiplicativa de Sidoroff y requiere un comportamiento viscoso isótropo. La formulación converge al modelo de Reese y Govindjee en el caso especial de isotropía elástica. El segundo modelo se define a partir de una descomposición multiplicativa inversa. Esta formulación está basada en una descripción co-rotacional del problema, es sustancialmente más compleja y puede dar lugar a tensores constitutivos ligeramente no simétricos. Sin embargo, su rango de aplicación es mucho mayor ya que permite un comportamiento anisótropo tanto elástico como viscoso. Varias simulaciones de elementos finitos muestran la gran versatilidad de estos modelos cuando se combinan con funciones hiperelásticas formadas por splines. ABSTRACT The mechanical behavior of many polymeric and biological materials may be properly modelled be means of isochoric hyperelastic and viscoelastic formulations. These materials may sustain large strains. The viscoelastic computational formulations for isotropic incompressible materials at large strains may be considered well established; for example Ogden’s hyperelastic function and the visco-hyperelastic model of Reese and Govindjee are well known models for isotropy. However, anisotropic models and computational procedures both for hyperelasticity and viscohyperelasticity are still under substantial research. Anisotropic hyperelastic models are typically based on structural invariants obtained from quadratic strain measures. These models may be microstructurallybased or phenomenological continuum formulations, and are characterized by a predefined analytical shape of the stored energy. The actual final expression of the stored energy depends on some material parameters which are obtained from an optimization algorithm, typically the Levenberg-Marquardt algorithm. We present in this work anisotropic spline-based hyperelastic stored energies in which the shape of the stored energy is obtained as part of the procedure and which (exactly in practice) replicates the experimental data. These stored energies are based on invariants obtained from logarithmic strain measures. These strain measures preserve the metric and the physical meaning of the trace and deviator operators and, hence, are interesting and meaningful for anisotropic formulations. Furthermore, the proposed stored energies may be formulated in order to have material-symmetries congruency both from a theoretical and from a numerical point of view, which are new properties that we define in this work. On the other hand, visco-hyperelastic formulations for anisotropic materials are typically based on internal stress-like variables following a procedure used by Sim´o. However, it can be shown that this procedure is not adequate for large deviations from thermodynamic equilibrium. In contrast, a formulation given by Reese and Govindjee is valid for arbitrarily large deviations from thermodynamic equilibrium but not for anisotropic stored energy functions. In this work we present two formulations for visco-hyperelasticity valid for anisotropic stored energies and large deviations from thermodynamic equilibrium. One of the formulations is based on the Sidoroff multiplicative decomposition and converges to the Reese and Govindjee formulation for the case of isotropy. However, the formulation is restricted to isotropy for the viscous component. The second formulation is based on a reversed multiplicative decomposition. This last formulation is substantially more complex and based on a corotational description of the problem. It can also result in a slightly nonsymmetric tangent. However, the formulation allows for anisotropy not only in the equilibrated and non-equilibrated stored energies, but also in the viscous behavior. Some examples show finite element implementation, versatility and interesting characteristics of the models.

Economic evaluation of occupational safety preventive measures in a hospital

BACKGROUND: When an organization performs an integrated analysis of risks through its Occupational Health and Safety Management System, several steps are suggested to address the implications of the identified risks. Namely, the organization should make a detailed analysis of the monetary impact for the organization of each of the preventive measures considered. However, it is also important to perform an analysis of the impact of each measure on society (externalities). OBJECTIVE: The aim of this paper is to present a case study related to the application of the proposed economic evaluation methodology. METHODS: An analysis of the work accidents in a hospital has been made. Three of the major types of accidents have been selected: needle stings, falls and excessive strain. Following the risk assessment, some preventive measures have been designed. Subsequently, the Benefit/Cost ratio (B/C) of these measures has been calculated, both in financial terms (from the organization’s perspective) and in economic terms (including the benefits for the worker and for the Society). RESULTS: While the financial ratio is only advantageous in some cases, when the externalities are taken into account, the B/C ratio increases significantly. CONCLUSIONS: It is important to consider external benefits to make decisions concerning the implementation of preventive measures in Occupational Health and Safety projects

Biological and morphological characteristics of Schistosoma mansoni from Ribeira Valley, State of São Paulo, Brazil: I - susceptibility of Biomphalaria tenagophila snail to sympatric S. mansoni strain

In the São Paulo State, Brazil, where the Biomphalaria tenagophila is the intermediate host, the Ribeira Valley is an important endemic schistosomiasis mansoni area. During last eleven years there has been intense control measures focusing on schistosomiasis. The efforts have been concentrated in the municipalities of Pedro de Toledo and Itariri. We determined the susceptibility of B. tenagophila to sympatric strain of S. mansoni, both recently isolated from Itariri field. In 1988, this strain was isolated and maintained in the experimental model: Swiss mice - sympatric B. tenagophila. The second generation of the worm was evaluated. The snail were divided in the three groups of 60 snails each. One group was exposed to 1 miracidium and other to 10. The third group was the control. The mortality and the shedding of cercariae were checked during 78 days. After that, the positive snails were observed until they ceased to shed cercariae. The exposed molluscs showed mortality rates of 23% and 31% and infection indexes were of 8% and 60% to 1 and 10 miracidia respectively. The mortality was of 22% in the control group. The periods of shedding cercariae in the two groups were 82 and 104 days. We can conclude that B. tenagophila is an effective intermediate host to the sympatric strain of S. mansoni sympatric strain

Economic evaluation of occupational safety preventive measures in a hospital

BACKGROUND: When an organization performs an integrated analysis of risks through its Occupational Health and Safety Management System, several steps are suggested to address the implications of the identified risks. Namely, the organization should make a detailed analysis of the monetary impact for the organization of each of the preventive measures considered. However, it is also important to perform an analysis of the impact of each measure on society (externalities). OBJECTIVE: The aim of this paper is to present a case study related to the application of the proposed economic evaluation methodology. METHODS: An analysis of the work accidents in a hospital has been made. Three of the major types of accidents have been selected: needle stings, falls and excessive strain. Following the risk assessment, some preventive measures have been designed. Subsequently, the Benefit/Cost ratio (B/C) of these measures has been calculated, both in financial terms (from the organization’s perspective) and in economic terms (including the benefits for the worker and for the Society). RESULTS: While the financial ratio is only advantageous in some cases, when the externalities are taken into account, the B/C ratio increases significantly. CONCLUSIONS: It is important to consider external

Integrated control measures against Culex quinquefasciatus, the vector of filariasis in Recife

Integrated control measures against Culex quinquefasciastus have been implemented in a pilot urban area in Recife, Brazil. About 3,000 breeding sites found within the operational area were responsible for very high mosquito densities recorded during the pretrial period. Physical control measures have been applied to cess pits before starting a series of 37 treatments of the other sites with Bacillus sphaericus strain 2362, over 27 months. In spite of the difficulties due to environmental conditions, very significant reductions in preimaginal population of C. quinquefasciatus were achieved and, as a consequence, low adult mosquito densities were maintained for a relatively long period of time. Entomological and environmental data gathered in this pilot project can contribute to design an integrated mosquito control program in Recife city.

Rotavirus A genotype G1P[8]: a novel method to distinguish wild-type strains from the Rotarix® vaccine strain

Rotaviruses are important enteric pathogens for humans and animals. Group A rotaviruses (RV-A) are the most common agents of severe gastroenteritis in infants and young children and vaccination is the most effective method to reduce RV-A-associated diseases. G1P[8], the most prevalent RV-A genotype worldwide, is included in the RV-A vaccine Rotarix®. The discrimination between wild-type G1P[8] and vaccine G1P[8] strains is an important topic in the study of RV-A epidemiology to manage outbreaks and to define control measures for vaccinated children. In this study, we developed a novel method to segregate the wild-type and vaccine strains using restriction endonucleases. The dsRNA from the Rotarix® vaccine was sequenced and the NSP3 gene was selected as the target gene. The vaccine strain has a restriction pattern that is different than that of wild-type RV-A G1P[8] isolates after digestion with the restriction endonuclease BspHI. This pattern could be used as a marker for the differentiation of wild-type G1P[8] strains from the vaccine strain.

Strain diversity of mycobacteria isolated from pulmonary tuberculosis patients at Debre Birhan Hospital, Ethiopia.

BACKGROUND: Ethiopia ranks seventh in the list of 22 high tuberculosis (TB) burden countries, with an incidence rate of 379 cases per 100 000 population for TB all forms. However, information on the genomic diversity of Mycobacterium tuberculosis in Ethiopia is limited. OBJECTIVE: To investigate the molecular characteristics of M. tuberculosis strains implicated in pulmonary TB in the study area. METHODS AND RESULTS: A cross-sectional study was conducted using socio-demographic, clinical and culture data combined with molecular typing analysis. The proportion of TB and M. tuberculosis isolates was not associated with risk factors (P > 0.05). Of 99 sputum samples, 80.8% were culture-positive. Speciation of isolates showed that 88.8% were M. tuberculosis. Further characterisation led to the identification of 27 different spoligotype patterns of M. tuberculosis; the most dominant shared types were SIT149, SIT53 and SIT54. Of the 27 strains, three strains were new and were reported to the SITVIT database. More than two thirds of the strains belonged to the Euro-American lineage. CONCLUSION: This study shows the presence of several clusters and new strains of M. tuberculosis circulating in pulmonary TB patients in the study area, suggesting recent transmission. Nationwide studies are recommended to map the population structure of M. tuberculosis and set control measures.

Methicillin-resistant Staphylococcus aureus with intermediate susceptibility to vancomycin: are strict additional contact measures sufficient?

Background: A hospitalised patient infected with MRSA was found to harbour a VISA strain after 6 weeks of treatment with vancomycin. Additional contact measures were reinforced according to CDCs recommendations. We decide to evaluate if these applied control measures were effective. Objective: To evaluate the efficacy of strict additional contact measures to contain the dissemination of VISA from an infected patient. Methods: All patients from the unit were screened weekly for MRSA during a 6-week period, whereas health care workers (HCW) were screened only once. Screening specimen included nose, throat, groin, and clinical specimens for patients, and only nose and throat for HCW. Broth enrichment and chromogenic agar (MRSA-select) were used for MRSA detection. All MRSA isolates were tested on Van screen plates, and growing colonies were tested for MIC of vancomycin. MIC was performed using Etest. Population analysis was done for VISA confirmation. One strain per person was typed by Double Locus Sequence Typing (based on clfB and spa sequencing). Results: 66 patients hospitalized in the same service during the 6 weeks and 55 HCW were screened for MRSA and VISA. MRSA was found in 16/66 (24%) patients and 1/55 (2%) HCW. 16/17 MRSA from patients belonged to the same genotype that the VISA strain. The remaining patient had a MRSA identical to the HCW isolate. Among the 16 MRSA isolates sharing the same genotype than the VISA strain, two showed Etests vancomycin MIC of only 4 mg/L. MIC results were confirmed by the population analysis. They were not considered as VISA, but as MRSA with increased vancomycin MICs. Both isolates were obtained from two roommates. Conclusion: Strict additional contact measures were found to be effective to contain VISA dissemination. However, the identification of two isolates with increased vancomycin MIC (4 mg/L) in two roommates raised the question of the need to routinely test this susceptibility and of adequate control measures for patients harbouring such isolates.

Hospital outbreak of methicillin-resistant Staphylococcus aureus caused by a new, possibly hyperepidemic variant from a previously sporadic strain.

Objective: To describe an ongoing outbreak that tripled the annual detection of methicillin-resistant Staphylococcus aureus (MRSA) carriage in a tertiary care hospital. Methods: Active surveillance of MRSA is performed since 20 years in our hospital. Our protocol includes screening of patients transferred from high-incidence health-care institutions or countries, roommates of new MRSA cases, and wards where _2 patients acquired MRSA during the same week. Contact precautions are used for known carriers. PFGE was used for molecular typing until 2004, and was then replaced by Double-Locus Sequence Typing (DLST). Results: A median yearly incidence of 173 new carriers of MRSA was observed from 2002 to 2007. Since September 2008, an increasing number of new cases were observed, mainly as successive clusters limited to distinct wards, reaching a total of 398 until October 2009. The yearly incidence of new cases rose to 275 in 2008 and 613 in 2009. 60% of the cases were due to one strain: DLST 4−4, ST 228, SCCmecI. The incidence of new cases due to the previously predominant strains remained unchanged. The epidemic strain corresponded to a new variant of a clone responsible for a previous outbreak in 2001, and only sporadically isolated (mean of 20 cases/year) since then. A case- control study documented a significant association between acquisition of the epidemic strain and a stay in intensive and intermediary care units, a highest number of internal transfers, but did not identify a point source of transmission. Infection control practices and antibiotic policy had remained unchanged for several years. Compliance with handhygiene as monitored yearly was on the rise. Screening of 313 healthcare workers only found one carrier of the epidemic strain lately in the outbreak. Additional infection control measures were enforced, including screening at ICU admission and discharge with PCR-based rapid test, routine screening for all patients leaving epidemic wards, introduction of PCR-based rapid test for contact tracing, additional working forces for environmental disinfection, and hospital-wide education of healthcare workers. However, the outbreak was still ongoing after 5 months. Conclusions: Factors linked to the dissemination of this new variant in our institution remain undetermined. This unresolved outbreak suggests that this new variant acquired hyperepidemic properties, which calls for further investigations.

Strain-dependent effects of diazepam and the 5-HT2B/2C receptor antagonist SB 206553 in spontaneously hypertensive and Lewis rats tested in the elevated plus-maze

The 5-HT2B/2C receptor antagonist SB 206553 exerts anxiolytic effects in rat models of anxiety. However, these effects have been reported for standard rat strains, thus raising the issue of SB 206553 effects in rat strains displaying different levels of anxiety. Herein, the effects of SB 206553 in a 5-min elevated plus-maze test of anxiety were compared to those of the reference anxiolytic, diazepam, in two rat strains respectively displaying high (Lewis rats) and low (spontaneously hypertensive rats, SHR) anxiety. Diazepam (0.37, 0.75, or 1.5 mg/kg; 30 min before testing) increased in a dose-dependent manner the behavioral measures in SHR, but not in Lewis rats. On the other hand, SB 206553 (1.25, 2.5, or 5 mg/kg; 30 min before testing) failed to alter the anxiety parameters in both strains, whereas it increased closed arm entries in Lewis rats, suggesting that it elicited hyperactivity in the latter strain. Accordingly, the hypolocomotor effect of the nonselective 5-HT2B/2C receptor agonist m-chlorophenylpiperazine (1.5 mg/kg ip 20 min before a 15-min exposure to an activity cage) was prevented by the 1.25 and 2.5 mg/kg doses of SB 206553 in Lewis rats and SHR, respectively. Compared with SHR, Lewis rats may display a lower response to benzodiazepine-mediated effects and a more efficient control of locomotor activity by 5-HT2B/2C receptors.