Prediction of Shallow Landslide prone regions in Undulating Terrains

Genetic Algorithm for Rule-set Prediction (GARP) and Support Vector Machine (SVM) with free and open source software (FOSS) - Open Modeller were used to model the probable landslide occurrence points. Environmental layers such as aspect, digital elevation, flow accumulation, flow direction, slope, land cover, compound topographic index and precipitation have been used in modeling. Simulated output of these techniques is validated with the actual landslide occurrence points, which showed 92% (GARP) and 96% (SVM) accuracy considering precipitation in the wettest month and 91% and 94% accuracy considering precipitation in the wettest quarter of the year.

Mapping of risk and susceptibility of shallow-landslide in the city of Sao Paulo, Brazil

In the city of Sao Paulo, where about 11 million people live, landslides and flooding occur frequently, especially during the summer. These landslides cause the destruction of houses and urban equipment, economic damage, and the loss of lives. The number of areas threatened by landslides has been increasing each year. The objective of this article is to analyze the probability of risk and susceptibility to shallow landslides in the Limoeiro River basin, which is located at the head of the Aricanduva River basin, one of the main hydrographic basins in the city of Sao Paulo. To map areas of risk, we created a cadastral survey form to evaluate landslide risk in the field. Risk was categorized into four levels based on natural and anthropogenic factors: R1 (low risk), R2 (average risk), R3 (high risk), and R4 (very high risk). To analyze susceptibility to shallow landslides, we used the SHALSTAB (Shallow Landsliding Stability) mathematical model and calculated the Distribution Frequency (DF) of the susceptibility classes for the entire basin. Finally, we performed a joint analysis of the average Risk Concentration (RC) and Risk Potential (RP). We mapped 14 risk sectors containing approximately 685 at-risk homes, more than half of which presented a high (R3) or very high (R4) probability of risk to the population. In the susceptibility map, 41% of the area was classified as stable and 20% as unconditionally unstable. Although the latter category accounted a smaller proportion of the total area, it contained a concentration (RC) of 41% of the mapped risk areas with a risk potential (RP) of 12%. We found that the locations of areas predicted to be unstable by the model coincided with the risk areas mapped in the field. This combination of methods can be applied to evaluate the risk of shallow landslides in densely populated areas and can assist public managers in defining areas that are unstable and inappropriate for occupation. (C) 2012 Elsevier B.V. All rights reserved.

Shallow Landslide Risk Assessment of the Westerly Bluffs of the 7.5-minute Freeland Quadrangle, Whidbey Island, Washington

Landslides often occur on slopes rendered unstable by underlying geology, geomorphology, hydrology, weather-climate, slope modifications, or deforestation. Unfortunately, humans commonly exacerbate such unstable conditions through careless or imprudent development practices. Due to local geology, geography, and climatic conditions, Puget Sound of western Washington State is especially landslide-prone. Despite this known issue, detailed analyses of landslide risks for specific communities are few. This study aims to classify areas of high landslide risk on the westerly bluffs of the 7.5 minute Freeland quadrangle based on a combined approach: mapping using LiDAR imagery and the Landform Remote Identification Model (LRIM) to identify landslides, and implementation of the Shallow Slope Stability Model (SHALSTAB) to establish a landslide exceedance probability. The objective is to produce a risk assessment from two shallow landslide scenarios: (1) minimum bluff setback and runout and (2) maximum bluff setback and runout. A simple risk equation that takes into account the probability of hazard occurrence with physical and economic vulnerability (van Westen, 2004) was applied to both scenarios. Results indicate an possible total loss as much as $32.6b from shallow landslides, given a setback of 12 m and a runout of 235 m.

滑坡泥石流信息遥感获取与空间预测

On the issue of geological hazard evaluation（GHE）, taking remote sensing and GIS systems as experimental environment, assisting with some programming development, this thesis combines multi-knowledges of geo-hazard mechanism, statistic learning, remote sensing (RS), high-spectral recognition, spatial analysis, digital photogrammetry as well as mineralogy, and selects geo-hazard samples from Hong Kong and Three Parallel River region as experimental data, to study two kinds of core questions of GHE, geo-hazard information acquiring and evaluation model. In the aspect of landslide information acquiring by RS, three detailed topics are presented, image enhance for visual interpretation, automatic recognition of landslide as well as quantitative mineral mapping. As to the evaluation model, the latest and powerful data mining method, support vector machine (SVM), is introduced to GHE field, and a serious of comparing experiments are carried out to verify its feasibility and efficiency. Furthermore, this paper proposes a method to forecast the distribution of landslides if rainfall in future is known baseing on historical rainfall and corresponding landslide susceptibility map. The details are as following: (a) Remote sensing image enhancing methods for geo-hazard visual interpretation. The effect of visual interpretation is determined by RS data and image enhancing method, for which the most effective and regular technique is image merge between high-spatial image and multi-spectral image, but there are few researches concerning the merging methods of geo-hazard recognition. By the comparing experimental of six mainstream merging methods and combination of different remote sensing data source, this thesis presents merits of each method ,and qualitatively analyzes the effect of spatial resolution, spectral resolution and time phase on merging image. (b) Automatic recognition of shallow landslide by RS image. The inventory of landslide is the base of landslide forecast and landslide study. If persistent collecting of landslide events, updating the geo-hazard inventory in time, and promoting prediction model incessantly, the accuracy of forecast would be boosted step by step. RS technique is a feasible method to obtain landslide information, which is determined by the feature of geo-hazard distribution. An automatic hierarchical approach is proposed to identify shallow landslides in vegetable region by the combination of multi-spectral RS imagery and DEM derivatives, and the experiment is also drilled to inspect its efficiency. (c) Hazard-causing factors obtaining. Accurate environmental factors are the key to analyze and predict the risk of regional geological hazard. As to predict huge debris flow, the main challenge is still to determine the startup material and its volume in debris flow source region. Exerting the merits of various RS technique, this thesis presents the methods to obtain two important hazard-causing factors, DEM and alteration mineral, and through spatial analysis, finds the relationship between hydrothermal clay alteration minerals and geo-hazards in the arid-hot valleys of Three Parallel Rivers region. (d) Applying support vector machine (SVM) to landslide susceptibility mapping. Introduce the latest and powerful statistical learning theory, SVM, to RGHE. SVM that proved an efficient statistic learning method can deal with two-class and one-class samples, with feature avoiding produce ‘pseudo’ samples. 55 years historical samples in a natural terrain of Hong Kong are used to assess this method, whose susceptibility maps obtained by one-class SVM and two-class SVM are compared to that obtained by logistic regression method. It can conclude that two-class SVM possesses better prediction efficiency than logistic regression and one-class SVM. However, one-class SVM, only requires failed cases, has an advantage over the other two methods as only "failed" case information is usually available in landslide susceptibility mapping. (e) Predicting the distribution of rainfall-induced landslides by time-series analysis. Rainfall is the most dominating factor to bring in landslides. More than 90% losing and casualty by landslides is introduced by rainfall, so predicting landslide sites under certain rainfall is an important geological evaluating issue. With full considering the contribution of stable factors (landslide susceptibility map) and dynamic factors (rainfall), the time-series linear regression analysis between rainfall and landslide risk mapis presented, and experiments based on true samples prove that this method is perfect in natural region of Hong Kong. The following 4 practicable or original findings are obtained: 1) The RS ways to enhance geo-hazards image, automatic recognize shallow landslides, obtain DEM and mineral are studied, and the detailed operating steps are given through examples. The conclusion is practical strongly. 2) The explorative researching about relationship between geo-hazards and alteration mineral in arid-hot valley of Jinshajiang river is presented. Based on standard USGS mineral spectrum, the distribution of hydrothermal alteration mineral is mapped by SAM method. Through statistic analysis between debris flows and hazard-causing factors, the strong correlation between debris flows and clay minerals is found and validated. 3) Applying SVM theory (especially one-class SVM theory) to the landslide susceptibility mapping and system evaluation for its performance is also carried out, which proves that advantages of SVM in this field. 4) Establishing time-serial prediction method for rainfall induced landslide distribution. In a natural study area, the distribution of landslides induced by a storm is predicted successfully under a real maximum 24h rainfall based on the regression between 4 historical storms and corresponding landslides.

Landslide Susceptible Locations in Western Ghats: Prediction through openModeller

Many shallow landslides are triggered by heavy rainfall on hill slopes resulting in enormous casualties and huge economic losses in mountainous regions. Hill slope failure usually occurs as soil resistance deteriorates in the presence of the acting stress developed due to a number of reasons such as increased soil moisture content, change in land use causing slope instability, etc. Landslides triggered by rainfall can possibly be foreseen in real time by jointly using rainfall intensity-duration and information related to land surface susceptibility. Terrain analysis applications using spatial data such as aspect, slope, flow direction, compound topographic index, etc. along with information derived from remotely sensed data such as land cover / land use maps permit us to quantify and characterise the physical processes governing the landslide occurrence phenomenon. In this work, the probable landslide prone areas are predicted using two different algorithms – GARP (Genetic Algorithm for Rule-set Prediction) and Support Vector Machine (SVM) in a free and open source software package - openModeller. Several environmental layers such as aspect, digital elevation data, flow accumulation, flow direction, slope, land cover, compound topographic index, and precipitation data were used in modelling. A comparison of the simulated outputs, validated by overlaying the actual landslide occurrence points showed 92% accuracy with GARP and 96% accuracy with SVM in predicting landslide prone areas considering precipitation in the wettest month whereas 91% and 94% accuracy were obtained from GARP and SVM considering precipitation in the wettest quarter of the year.

Geotechnical monitoring using a combination of LIDAR, real-time dGPS, and electrical tomography to assess geotechnical risk of a coastal landslide.

The Antrim Coast Road stretching from the seaport of Larne in the East of Northern Ireland has a well-deserved reputation for being one of the most spectacular roads in Europe (Day, 2006). However the problematic geology; Jurassic Lias Clay and Triassic Mudstone overlain by Cretaceous Limestone and Tertiary Basalt, and environmental variables result in frequent instances of slope instability manifested in both shallow debris flows and occasional massive rotational movements, creating a geotechnical risk to this highway. This paper describes how a variety of techniques are being used to both assess instability and monitor movement of these active slopes near one site at Straidkilly Point, Glenarm. An in-depth understanding of the geology was obtained via boreholes, resistivity surveys and laboratory testing. Environmental variables recorded by an on-site weather station were correlated with measured pore water pressure and soil moisture infiltration data. Terrestrial LiDAR (TLS), with surveys carried out on a bi-monthly basis allowed for the generation of Digital Elevation Models (DEMs) of difference, highlighting areas of recent movement, accumulation and depletion. Morphology parameters were generated from the DEMs and include slope, curvature and multiple measures of roughness. Changes in the structure of the slope coupled with morphological parameters were characterised and linked to progressive failures from the temporal monitoring. In addition to TLS monitoring, Aerial LiDAR datasets were used for the spatio-morphological characterisation of the slope on a macro scale. A Differential Global Positioning System (dGPS) was also deployed on site to provide a real-time warning system for gross movements, which were also correlated with environmental conditions. Frequent electrical resistivity tomography (ERT) surveys were also implemented to provide a better understanding of long-term changes in soil moisture and help to define the complex geology. The paper describes how the data obtained via a diverse range of methods has been combined to facilitate a more informed management regime of geotechnical risk by the Northern Ireland Roads Service.

Landslide susceptibility evaluation and validation at a regional scale

Tese de doutoramento, Geografia (Geografia Física), Universidade de Lisboa, Instituto de Geografia e Ordenamento do Território, 2014

A comparison of landslide inventories along the shoreline of Steamboat Island Peninsula, Thurston County, WA: office based protocol vs. field based protocol

The mountain ranges and coastlines of Washington State have steep slopes, and they are susceptible to landslides triggered by intense rainstorms, rapid snow melts, earthquakes, and rivers and waves removing slope stability. Over a 30-year timespan (1984-2014 and includes State Route (SR) 530), a total of 28 deep-seated landslides caused 300 million dollars of damage and 45 deaths (DGER, 2015). During that same timeframe, ten storm events triggered shallow landslides and debris flows across the state, resulting in nine deaths (DGER, 2015). The loss of 43 people, due to the SR 530 complex reactivating and moving at a rate and distance unexpected to residents, highlighted the need for an inventory of the stateís landslides. With only 13% of the state mapped (Lombardo et al., 2015), the intention of this statewide inventory is to communicate hazards to citizens and decision makers. In order to compile an accurate and consistent landslide inventory, Washington needs to adopt a graphic information system (GIS) based mapping protocol. A mapping protocol provides consistency for measuring and recording information about landslides, including such information as the type of landslide, the material involved, and the size of the movement. The state of Oregon shares similar landslide problems as Washington, and it created a GIS-based mapping protocol designed to inform its residents, while also saving money and reducing costly hours in the field (Burns and Madin, 2009). In order to determine if the Oregon Department of Geology and Mineral Industries (DOGAMI) protocol, developed by Burns and Madin (2009), could serve as the basis for establishing Washingtonís protocol, I used the office-based DOGAMI protocol to map landslides along a 40-50 km (25-30 mile) shoreline in Thurston County, Washington. I then compared my results to the field-based landslide inventory created in 2009 by the Washington Division of Geology and Earth Resources (DGER) along this same shoreline. If the landslide area I mapped reasonably equaled the area of the DGER (2009) inventory, I would consider the DOGAMI protocol useful for Washington, too. Utilizing 1m resolution lidar flown for Thurston County in 2011 and a GIS platform, I mapped 36 landslide deposits and scarp flanks, covering a total area of 879,530 m2 (9,467,160 ft2). I also found 48 recent events within these deposits. With an exception of two slides, all of the movements occurred within the last fifty years. Along this same coastline, the DGER (2009) recorded 159 individual landslides and complexes, for a total area of 3,256,570 m2 (35,053,400 ft2). At a first glance it appears the DGER (2009) effort found a larger total number and total area of landslides. However, in addition to their field inventory, they digitized landslides previously mapped by other researchers, and they did not field confirm these landslides, which cover a total area of 2,093,860 m2 (22,538,150 ft2) (DGER, 2009). With this questionable landslide area removed and the toes and underwater landslides accounted for because I did not have a bathymetry dataset, my results are within 6,580 m2 (70,840 ft2) of the DGERís results. This similarity shows that the DOGAMI protocol provides a consistent and accurate approach to creating a landslide inventory. With a few additional modifications, I recommend that Washington State adopts the DOGAMI protocol. Acquiring additional 1m lidar and adopting a modified DOGAMI protocol poises the DGER to map the remaining 87% of the state, with an ultimate goal of informing citizens and decision makers of the locations and frequencies of landslide hazards on a user-friendly GIS platform.

Brucite Microbialites in Living Coral Skeletons: Indicators of Extreme Microenvironments in Shallow-Marine Settings

Brucite [Mg(OH)2] microbialites occur in vacated interseptal spaces of living scleractinian coral colonies (Acropora, Pocillopora, Porites) from subtidal and intertidal settings in the Great Barrier Reef, Australia, and subtidal Montastraea from the Florida Keys, United States. Brucite encrusts microbial filaments of endobionts (i.e., fungi, green algae, cyanobacteria) growing under organic biofilms; the brucite distribution is patchy both within interseptal spaces and within coralla. Although brucite is undersaturated in seawater, its precipitation was apparently induced in the corals by lowered pCO2 and increased pH within microenvironments protected by microbial biofilms. The occurrence of brucite in shallow-marine settings highlights the importance of microenvironments in the formation and early diagenesis of marine carbonates. Significantly, the brucite precipitates discovered in microenvironments in these corals show that early diagenetic products do not necessarily reflect ambient seawater chemistry. Errors in environmental interpretation may arise where unidentified precipitates occur in microenvironments in skeletal carbonates that are subsequently utilized as geochemical seawater proxies.

A Hybrid AUV design for shallow water reef navigation

The highly unstructured nature of coral reef environments makes them difficult for current robotic vehicles to efficiently navigate. Typical research and commercial platforms have limited autonomy within these environments and generally require tethers and significant external infrastructure. This paper outlines the development of a new robotic vehicle for underwater monitoring and surveying in highly unstructured environments and presents experimental results illustrating the vehicle’s performance. The hybrid AUV design developed by the CSIRO robotic reef monitoring team realises a compromise between endurance, manoeuvrability and functionality. The vehicle represents a new era in AUV design specifically focused at providing a truly low-cost research capability that will progress environmental monitoring through unaided navigation, cooperative robotics, sensor network distribution and data harvesting.

Mapping of shallow coastal groundwaters, their hydrology and environmental geochemistry : Pumicestone catchment, Southeast Queensland

Blooms of the toxic cyanobacterium majuscula Lyngbya in the coastal waters of southeast Queensland have caused adverse impacts on both environmental health and human health, and on local economies such as fishing and tourism. A number of studies have confirmed that the main limiting nutrients (“nutrients of concern”) that contribute to these blooms area Fe, DOC, N, P and also pH. This study is conducted to establish the distribution of these parameters in a typical southeast Queensland coastal setting. The study maps the geochemistry of shallow groundwater in the mainland Pumicestone catchment with an emphasis on the nutrients of concern to understand how these nutrients relate to aquifer materials, landuse and anthropogenic activities. The results of the study form a GIS information layer which will be incorporated into a larger GIS model being produced by Queensland Department of Environment and Resource Management (DERM) to support landuse management to avoid/minimize blooms of Lyngbya in Moreton Bay, southeast Queensland, and other similar settings. A total of 38 boreholes were established in the mainland Pumicestone region and four sampling rounds of groundwater carried out in both dry and wet conditions. These groundwater samples were measured in the field for physico-chemical parameters, and in the laboratory analyses for the nutrients of concern, and other major and minor ions. Aquifer materials were confirmed using the Geological Survey of Queensland digital geology map, and geomaterials were assigned to seven categories which are A (sands), B (silts, sandy silts), C (estuarine mud, silts), D (humid soils), E (alluvium), F (sandstone) and G (other bedrock). The results of the water chemistry were examined by use of the software package AquaChem/AqQA, and divided into six groundwater groups, based on groundwater chemical types and location of boreholes. The type of aquifer material and location, and proximity to waterways was found to be important because they affected physico-chemical properties and concentrations of nutrients of concern and dissolved ions. The analytical results showed that iron concentrations of shallow groundwaters were high due to acid sulfate soils, and also mud and silt, but were lower in sand materials. DOC concentrations of these shallow groundwaters in the sand material were high probably due to rapid infiltration. In addition, DOC concentrations in some boreholes were high because they were installed in organic rich wetlands. The pH values of boreholes were from acidic to near neutral; some boreholes with pH values were low (< 4), showing acid sulfate soils in these boreholes. Concentrations of total nitrogen and total phosphorus of groundwaters were generally low, and the main causes of elevated concentrations of total nitrogen and total phosphorus are largely due to animal and human wastes and tend to be found in localized source areas. Comparison of the relative percentage of nitrogen species (NH3/NH4< Org-N, NO3-N and NO2-N) demonstrated that they could be related to sources such as animal waste, residential and agricultural fertilizers, forest and vegetation, mixed residents and farms, and variable setting and vegetation covers. Total concentrations of dissolved ions in sampling round 3 (dry period) were higher than those in sampling round 2 (wet period) due to both evaporation of groundwater in the dry period and the dilution of rainfall in the wet period. This showed that the highest concentrations of nutrients of concern were due to acid sulfate soils, aquifer materials, landuse and anthropogenic activities and were typically in aquifer materials of E (alluvium) and C (estuarine muds) and locations of Burpengary, Caboolture, and Glass Mountain catchments.

Bacterially mediated iron cycling and associated biogeochemical processes in a subtropical shallow coastal aquifer: implications for groundwater quality

Bacterially mediated iron redox cycling exerts a strong influence on groundwater geochemistry, but few studies have investigated iron biogeochemical processes in coastal alluvial aquifers from a microbiological viewpoint. The shallow alluvial aquifer located adjacent to Poona estuary on the subtropical Southeast Queensland coast represents a redox-stratified system where iron biogeochemical cycling potentially affects water quality. Using a 300 m transect of monitoring wells perpendicular to the estuary, we examined groundwater physico-chemical conditions and the occurrence of cultivable bacterial populations involved in iron (and manganese, sulfur) redox reactions in this aquifer. Results showed slightly acidic and near-neutral pH, suboxic conditions and an abundance of dissolved iron consisting primarily of iron(II) in the majority of wells. The highest level of dissolved iron(III) was found in a well proximal to the estuary most likely a result of iron curtain effects due to tidal intrusion. A number of cultivable, (an)aerobic bacterial populations capable of diverse carbon, iron, or sulfur metabolism coexisted in groundwater redox transition zones. Our findings indicated aerobic, heterotrophic respiration and bacterially mediated iron/sulfur redox reactions were integral to carbon cycling in the aquifer. High abundances of dissolved iron and cultivable iron and sulfur bacterial populations in estuary-adjacent aquifers have implications for iron transport to marine waters. This study demonstrated bacterially mediated iron redox cycling and associated biogeochemical processes in subtropical coastal groundwaters using culture-based methods.

Modelling surface and shallow groundwater interactions in an ungauged subtropical coastal catchment using the SWAT model, Elimbah Creek, southeast Queensland, Australia

The study presented here applies the highly parameterised semi-distributed U.S. Department of Agriculture Soil and Water Assessment Tool (SWAT) to an Australian subtropical catchment. SWAT has been applied to numerous catchments worldwide and is considered to be a useful tool that is under ongoing development with contributions coming from different research groups in different parts of the world. In a preliminary run the SWAT model application for the Elimbah Creek catchment has estimated water yield for the catchment and has quantified the different sources. For the modelling period of April 1999 to September 2009 the results show that the main sources of water in Elimbah Creek are total surface runoff and lateral flow (65%). Base-flow contributes 36% to the total runoff. On a seasonal basis modelling results show a shift in the source of water contributing to Elimbah Creek from surface runoff and lateral flow during intense summer storms to base-flow conditions during dry months. Further calibration and validation of these results will confirm that SWAT provides an alternative to Australian water balance models.