Self-compression of femtosecond pulses in argon with a power close to the self-focusing threshold

Self-compression of femtosecond pulses in noble gases with an input power close to the self-focusing threshold has been investigated experimentally and theoretically. It is demonstrated that either multiphoton ionization (MPI) or space time focusing and self-steepening effects can induce pulse shortening, but they predominate at different beam intensities during the propagation. The latter effects play a key role in the final pulse self-compression. By choosing an appropriate focusing parameter, action distance of the space time focusing and self-steepening effects can be lengthened, which can promote a shock pulse structure with a duration as short as two optical cycles. It is also found that, for our calculation cases in which an input pulse power is close to the self-focusing threshold, either group velocity dispersion (GVD) or multiphoton absorption (MPA) has a negligible influence on pulse characteristics in the propagation process.

Pulse self-compression in normally dispersive bulk media

We experimentally demonstrate that high-power femtosecond pulses can be compressed during the nonlinear propagation in the normally dispersive solid bulk medium. The self-compression behavior was detailedly investigated under a variety of experimental conditions, and the temporal and spectral characteristics of resulted pulses were found to be significantly affected by the input pulse intensity, with higher intensity corresponding to shorter compressed pulses. By passing through a piece of BK7 glass, a self-compression from 50 to 20 fs was achieved, with a compression factor of about 2.5. However, the output pulse was observed to be split into two peaks when the input intensity is high enough to generate supercontinuum and conical emission. (c) 2005 Elsevier B.V. All rights reserved.

Relativistic laser pulse compression in plasmas with a linear axial density gradient

The self-compression of a relativistic Gaussian laser pulse propagating in a non-uniform plasma is investigated. A linear density inhomogeneity (density ramp) is assumed in the axial direction. The nonlinear Schrodinger equation is first solved within a one-dimensional geometry by using the paraxial formalism to demonstrate the occurrence of longitudinal pulse compression and the associated increase in intensity. Both longitudinal and transverse self-compression in plasma is examined for a finite extent Gaussian laser pulse. A pair of appropriate trial functions, for the beam width parameter (in space) and the pulse width parameter (in time) are defined and the corresponding equations of space and time evolution are derived. A numerical investigation shows that inhomogeneity in the plasma can further boost the compression mechanism and localize the pulse intensity, in comparison with a homogeneous plasma. A 100 fs pulse is compressed in an inhomogeneous plasma medium by more than ten times. Our findings indicate the possibility for the generation of particularly intense and short pulses, with relevance to the future development of tabletop high-power ultrashort laser pulse based particle acceleration devices and associated high harmonic generation. An extension of the model is proposed to investigate relativistic laser pulse compression in magnetized plasmas.

飞秒激光脉冲在正色散固体材料中的自压缩

实验研究了正色散固体介质中的激光脉冲自压缩现象，证明了无需任何外加色散补偿情况下，固体透明介质中的自聚焦传输过程可使高功率飞秒激光脉冲实现时域脉冲压缩，并详细研究了输出脉冲的时域和频域特性随入射脉冲强度的演化规律．实验结果表明脉冲自压缩量随入射脉冲强度的增加呈递增趋势，然而当入射光强增大到足以引起超连续谱及锥形辐射产生时，脉冲时域形状会发生分裂．此外还发现发散光束入射情况下同样可以观察到脉冲自压缩现象．

高强度飞秒激光脉冲在空气中的自压缩

利用高重复频率(1kHz)、吉瓦级飞秒激光脉冲实验验证了高强度飞秒脉冲在空气中的自压缩现象，研究了入射脉冲在不同初始啁啾情况下经空气中聚焦成丝后，时域及频域特性随入射脉冲能量的变化规律．实验结果表明，在无需后继色散补偿情况下，高强度飞秒脉冲仅通过在空气中的非线性传输过程就可以实现脉冲压缩；在入射脉冲为负啁啾情况下，实验观察到脉冲光谱及时域宽度同时得到压缩，并可获得比激光源所能提供的更短的近双曲正割型变换限脉冲．

负啁啾高强度飞秒脉冲在正常色散材料中传输特性研究

利用块状正常色散材料作非线性介质，实验研究了负啁啾强激光飞秒脉冲在正常色散材料的传输过程中，脉冲波形及频谱随入射脉冲能量的变化特性．实验发现，负啁啾脉冲经过材料后激光光谱在被整形和压缩的同时，脉冲宽度也被压缩．实验获得的压缩脉冲宽度短于相等光谱宽度下的双曲正割转换极限脉冲宽度。数值模拟结果显示，在实验条件下模拟结果具有同样的变化特性．

圆偏振光和线偏振光在正常色散材料中的时空自压缩

实验研究了圆偏振和线偏振高强度飞秒激光脉冲在正常色散材料中传输时的时空自压缩现象。实验中利用BK7玻璃作为正色散材料，比较研究了不同偏振入射情况下脉冲波形及频谱的变化规律。圆偏振光入射时，可以获得更短脉冲宽度的压缩脉冲和更窄的光谱宽度。在圆偏振光入射条件下，50fs入射脉冲成功地自压缩到了19fs，获得了大于2．5倍的压缩倍率。所以利用圆偏振光可以获得更短压缩脉冲，更大能量，更好光束质量的激光。

Filamentation control in the temperature gradient argon gas

A novel technique of controlling the evolution of the filamentation was experimentally demonstrated in an argon gas-filled tube. The entrance of the filament was heated by a furnace and the other end was cooled with air, which resulted in the temperature gradient distribution along the tube. The experimental results show that multiple filaments are merged into a single filament and then no filament by only increasing the temperature at the entrance of the filament. Also, the filament can appear and disappear after increasing the local temperature and input pulse energy in turn. This technique offers another degree of freedom to control the filamentation and opens a new way for multi-mJ level monocycle pulse generation through filamentation in the noble gas.

Generation of 5 fs, 0.7 mJ pulses at 1 kHz through cascade filamentation

Two-cycle optical pulses with duration of 5 fs and energy of 0.7 mJ have been generated at 1 kHz by compressing the 38 fs laser pulses from a carrier-envelope phase (CEP) controlled Ti:sapphire laser system through a cascade filamentation compression technique. A simple and effective method is developed to suppress multiple filament formation and stabilize a single filament by inserting a soft aperture with an appropriate diameter into the driving laser beam prior to focusing, resulting in an excellent compressed beam quality. The good beam quality and potentially higher peak power make this ultrashort laser pulse source a significant tool for high-field physics applications. (C) 2007 Optical Society of America.

Simultaneous pulse compression and jitter reduction at 10GHz using novel self-seeding gain-switched DFB laser incorporating a DILM

A novel scheme using a 10 GHz gain-switched DFB laser with simultaneous pulse width and jitter compression allows generation of 380fs pulses with both system limited 150fs jitter and 30 dB extinction ratio. ©1999 Optical Society of America.

Compression and tensile properties of self-reinforced poly(ethylene terephthalate)-composites

Tensile and compression properties of self-reinforced poly(ethylene terephthalate) (SrPET) composites has been investigated. SrPET composites or all-polymer composites have improved mechanical properties compared to the bulk polymer but with maintained recyclability. In contrast to traditional carbon/glass fibre reinforced composites, SrPET composites are very ductile, resulting in high failure strains without softening or catastrophic failure. In tension, the SrPET composites behave linear elastically until the fibre-matrix interface fails, at which point the stiffness starts decreasing. As the material is further strained, strain hardening occurs and the specimen finally fails at a global strain above 10%. In compression, the composite initially fails through fibre yielding, and at higher strains through fibre bending. The stress-strain response is reminiscent of an elastic-perfectly plastic material with a high strain to failure (typically over 10%). This indicates that SrPET composites are not only candidates as semi-structural composites but also as highly efficient energy absorbing materials. © 2012 Elsevier Ltd. All rights reserved.

Compression of polymer brushes: quantitative comparison of self-consistent field theory with experiment

The self-consistent field theory (SCFT) prediction for the compression force between two semi-dilute polymer brushes is compared to the benchmark experiments of Taunton et al. [Nature, 1988, 332, 712]. The comparison is done with previously established parameters, and without any fitting parameters whatsoever. The SCFT provides a significant quantitative improvement over the classical strong-stretching theory (SST), yielding excellent quantitative agreement with the experiment. Contrary to earlier suggestions, chain fluctuations cannot be ignored for normal experimental conditions. Although the analytical expressions of SST provide invaluable aids to understanding the qualitative behavior of polymeric brushes, the numerical SCFT is necessary in order to provide quantitatively accurate predictions.

Combustion simulations for a self controlling variable compression ratio connecting rod

Variable compression ratio enables an engine to achieve increased efficiency at part loads, where the majority of driving occurs, without sacrificing full load power requirements or increasing the risk of engine knock. Although over 100 patents and patent applications exist none of these systems has been commercialized yet due to issues related to feasibility, cost and frictional loss. A new approach of a self controlling variable compression ratio connecting rod is presented that does not need a friction intensive external activation and that could even be retrofitted. The potential in fuel consumption and exhaust emission reduction as well as increased power and torque output for this concept has been verified in combustion simulations utilizing the latest research results related to the dynamic heat transfer in the combustion chamber from Professor Kleinschmidt from the University of Siegen, Germany. The self controlling variable compression ratio connecting rod allows the con rod to compress at high load conditions thereby increasing cylinder volume to alleviate combustion pressures and temperatures and therefore limit knock onset. The biggest efficiency gains can be achieved at medium load where the reduction of heat loss during the compression of the connecting rod plays a major role additional to the well known efficiency gains of an increased compression ratio. The combustion simulation results shows fuel consumption can be reduced by between 3% and 5% during part load and wide open throttle operation at various engine speeds. Emissions are also reduced significantly; particularly NOx and CO emissions were reduced by up to 35%.The self controlling variable compression ratio connecting rod allows the con rod to compress at high load conditions thereby increasing cylinder volume to alleviate combustion pressures and temperatures and therefore limit knock onset. The biggest efficiency gains can be achieved at medium load where the reduction of heat loss during the compression of the connecting rod plays a major role additional to the well known efficiency gains of an increased compression ratio.The combustion simulation results shows fuel consumption can be reduced by between 3% and 5% during part load and wide open throttle operation at various engine speeds. Emissions are also reduced significantly; particularly NOx and CO emissions were reduced by up to 35%.

Bio-inspired FPGA Architecture for Self-Calibration of an Image Compression Core based on Wavelet Transforms in Embedded Systems

A generic bio-inspired adaptive architecture for image compression suitable to be implemented in embedded systems is presented. The architecture allows the system to be tuned during its calibration phase. An evolutionary algorithm is responsible of making the system evolve towards the required performance. A prototype has been implemented in a Xilinx Virtex-5 FPGA featuring an adaptive wavelet transform core directed at improving image compression for specific types of images. An Evolution Strategy has been chosen as the search algorithm and its typical genetic operators adapted to allow for a hardware friendly implementation. HW/SW partitioning issues are also considered after a high level description of the algorithm is profiled which validates the proposed resource allocation in the device fabric. To check the robustness of the system and its adaptation capabilities, different types of images have been selected as validation patterns. A direct application of such a system is its deployment in an unknown environment during design time, letting the calibration phase adjust the system parameters so that it performs efcient image compression. Also, this prototype implementation may serve as an accelerator for the automatic design of evolved transform coefficients which are later on synthesized and implemented in a non-adaptive system in the final implementation device, whether it is a HW or SW based computing device. The architecture has been built in a modular way so that it can be easily extended to adapt other types of image processing cores. Details on this pluggable component point of view are also given in the paper.