Rod length influence in torque measurement of SPT-T test

Since Ranzini suggested supplementing the SPT test with measurement of the torque required to turn the split spoon sampler after driving, many Brazilian engineers have been using this in the design of pile foundations. This paper presents a study of the rod length influence in the torque measurement. A theoretical study of material resistance considering torsion and bending in a thin wall tubular steel shaft was performed. It makes possible to conclude that the shearing tension caused by the proper weight represents less than 1% of the shearing tension caused by the turning moment. In addition, an experimental study was done with electric torquemeters fixed in a horizontal rod system. The tests were being carried out to analyze rods of one meter to twenty meters in length and the measurements were collected at the ends of each rod length verifying the efficiency data. As a result, it is possible to verify that the torque difference through rod length is lower than minimum scales of mechanical torquemeters that are used on practical engineering. Also a fact to be considered is a big torque loss for values under 20 N.m of applied torque. This way, the SPT-T is not adequate to low consistency soil. Copyright ASCE 2007.

突出电极对四杆型RFQ腔体并联阻抗及场平整性的影响；Influence of projecting electrodes on shunt impedance and flatness of 4-rod radiofrequency quadrupole cavity

中国科学院近代物理研究所正在进行等离子体直接注入方案的研究,以便为重离子物理研究提供稳定可靠的高流强束流。由于工作频率较低,用于等离子体直接注入方案的RFQ腔体采用了适合于低频的四杆型结构。在完成束流动力学设计的前提下,研究了RFQ腔体支撑臂的各参数对并联阻抗的影响。由于突出电极之间存在着一定大小的电容,会对腔体的性能产生影响,为使腔体达到最优化的设计,进行了突出电极对并联阻抗及场平整性的影响的研究,并给出了突出电极的取值范围。

Influence of all-out and fast start of 5-min cycling time trial performance

Purpose: To examine the influence of two different fast-start pacing strategies on performance and oxygen consumption (V˙O2) during cycle ergometer time trials lasting ∼5 min. Methods: Eight trained male cyclists performed four cycle ergometer time trials whereby the total work completed (113 ± 11.5 kJ; mean ± SD) was identical to the better of two 5-min self-paced familiarization trials. During the performance trials, initial power output was manipulated to induce either an all-out or a fast start. Power output during the first 60 s of the fast-start trial was maintained at 471.0 ± 48.0 W, whereas the all-out start approximated a maximal starting effort for the first 15 s (mean power: 753.6 ± 76.5 W) followed by 45 s at a constant power output (376.8 ± 38.5 W). Irrespective of starting strategy, power output was controlled so that participants would complete the first quarter of the trial (28.3 ± 2.9 kJ) in 60 s. Participants performed two trials using each condition, with their fastest time trial compared. Results: Performance time was significantly faster when cyclists adopted the all-out start (4 min 48 s ± 8 s) compared with the fast start (4 min 51 s ± 8 s; P < 0.05). The first-quarter V˙O2 during the all-out start trial (3.4 ± 0.4 L·min-1) was significantly higher than during the fast-start trial (3.1 ± 0.4 L·min-1; P < 0.05). After removal of an outlier, the percentage increase in first-quarter V˙O2 was significantly correlated (r = -0.86, P < 0.05) with the relative difference in finishing time. Conclusions: An all-out start produces superior middle distance cycling performance when compared with a fast start. The improvement in performance may be due to a faster V˙O2 response rather than time saved due to a rapid acceleration.

Nanostructured CexZn1-xO thin films: Influence of Ce doping on the structural, optical and electrical properties

Thin films of CexZn1-xO thin films were deposited on glass substrates at 400 degrees C by nebulizer spray pyrolysis technique. Ce doping concentration (x) was varied from 0 to 10%, in steps of 2.5%. X-ray diffraction reveals that all the films have polycrystalline nature with hexagonal crystal structure and high preferential orientation along (002) plane. Optical parameters such as; transmittance, band gap energy, refractive index (n), extinction coefficient (k), complex dielectric constants (epsilon(r), epsilon(i)) and optical conductivity (sigma(r), sigma(i)) have been determined and discussed with respect to Ce concentration. All the films exhibit transmittance above 80% in the wavelength range from 330 to 2500 nm. Optical transmission measurements indicate the decrease of direct band gap energy from 3.26 to 3.12 eV with the increase of Ce concentration. Photoluminescence spectra show strong near band edge emission centered similar to 398 nm and green emission centered similar to 528 nm with excitation wavelength similar to 350 nm. High resolution scanning electron micrographs indicate the formation of vertical nano-rod like structures on the film surface with average diameter similar to 41 nm. Electrical properties of the Ce doped ZnO film have been studied using ac impedance spectroscopy in the frequency range from 100 Hz-1 MHz at different temperatures. (C) 2013 Elsevier B.V. All rights reserved.

Influence of liquid bridge volume on the onset of oscillation in floating-zone convection .1. Experiments

The onset of oscillation in the floating zone convection driven by the gradient of surface tension was experimentally studied, and discussions were concentrated on the influence of liquid bridge volume on the onset of oscillation. Distributions of critical applied temperature difference and frequency depending on the volume of the liquid bridge were obtained, and there was a gap range of liquid volume which separated the curve of marginal stability into two parts for fixed rod diameter and aspect ratio. The results imply that the volume of the liquid bridge is a sensitive critical parameter for the onset of oscillation. The implication on the instability is also discussed in the present paper.

An analysis of salmon rod catch data from castle fisheries, River Derwent, 1923-1989.

The aim of this study was to investigate the historical catch record from the Castle Fishery on the River Derwent over the period 1923 - 1989, to determine if changes had taken place in the composition of the catch and to examine the influence of flow on the performance of the fishery. The River Derwent is situated in West Cumbria, North West England. It flows from its source on Scafell Pike (NGR NY 229 089) westwards discharging into the Irish sea at Workington, a distance of 52 km. Over its length it receives water from an additional 214 km of stream, 5 large lakes and approximately 30 small tarns. The catchment drains a total area of 663 km2. The study concludes that through the time period there was considerable variation in catch between years. The trend was for the catch to increase steadily over the period 1923 - 1958, declining rapidly in 1959, after which catches increased steadily reaching a peak in the mid-sixties, before declining towards the end of the decade. During the seventies and eighties catches remained relatively stable at between 300 - 600 salmon per year until 1988 when over 2000 salmon were reported caught, the greatest number in any year over the study period.

Study on shunt impedance and voltage distribution of 4-rod RFQ cavity

A high current RFQ (radio frequency quadrupole) is being studied at the Institute of Modern Physics, CAS for the direct plasma injection scheme. Shunt impedance is air important parameter when designing a 4-rod RFQ cavity, it reflects the RF efficiency of the cavity, and has a direct influence on the cost of the structure. Voltage distribution of a RFQ cavity has an effect on beam transmission, and particles would be lost if the actual voltage distribution is not as what, it should be. The influence of cell length, stern thickness and height on Shunt impedance and voltage distribution have been studied, in particular the effect of projecting electrodes has been investigated in detail.

Study of self-assembly of symmetric coil-rod-coil ABA-type triblock copolymers by self-consistent field lattice method

The self-assembly of symmetric coil-rod-coil ABA-type triblock copolymer melts is studied by applying self-consistent field lattice techniques in a three-dimensional space. The self-assembled ordered structures differ significantly with the variation of the volume fraction of the rod component, which include lamellar, wave lamellar, gyroid, perforated lamellar, cylindrical, and spherical-like phases. To understand the physical essence of these phases and the regimes of occurrence, we construct the phase diagram, which matches qualitatively with the existing experimental results. Compared with the coil-rod AB diblock copolymer, our results revealed that the interfacial grafting density of the separating rod and coil segments shows important influence on the self-assembly behaviors of symmetric coil-rod-coil ABA triblock copolymer melts. We found that the order-disorder transition point changes from f(rod)=0.5 for AB diblock copolymers to f(rod)=0.6 for ABA triblock copolymers. Our results also show that the spherical-like and cylindrical phases occupy most of the region in the phase diagram, and the lamellar phase is found stable only at the high volume fraction of the rod.

Influence of embedded length on strength of BFRP rods bonded parallel to the grain in low grade timber by pullout-bending tests

Bonded-in rod connections in timber possess many desirable attributes in terms of efficiency, manufacture, performance, aesthetics and cost. In recent years research has been conducted on such connections using fibre reinforced polymers (FRPs) as an alternative to steel. This research programme investigates the pull-out capacity of Basalt FRP rods bonded-in in low grade Irish Sitka Spruce. Embedded length is thought to be the most influential variable contributing to pull- out capacity of bonded-in rods after rod diameter. Previous work has established an optimum embedded length of 15 times the hole diameter. However, this work only considered the effects of axial stress on the bond using a pull-compression testing system which may have given an artificially high pull out capacity as bending effects were neglected. A hinge system was utilised that allows the effects of bending force to be taken in to consideration along with axial forces in a pull-out test. This paper describes an experimental programme where such pull-bending tests were carried out on samples constructed of 12mm diameter BFRP bars with a 2mm glueline thickness and embedded lengths between 80mm and 280mm bonded-in to low-grade timber with an epoxy resin. Nine repetitions of each were tested. A clear increase in pull-out strength was found with increasing embedded length.

The influence of allopurinol on urinary purine loss after repeated sprint exercise in man

The influence of allopurinol on urinary purine loss was examined in 7 active male subjects (age 24.9 ± 3.0 years, weight 82.8 ± 8.3 kg, V˙o₂peak 48.1 ± 6.9 mL · kg⁻¹ · min⁻¹). These subjects performed, in random order, a trial with 5 days of prior ingestion of a placebo or allopurinol. Each trial consisted of eight 10-second sprints on an air-braked cycle ergometer and was separated by at least a week. A rest period of 50 seconds separated each repeated sprint. Forearm venous plasma inosine, hypoxanthine (Hx) and uric acid concentrations were measured at rest and during 120 minutes of recovery from exercise. Urinary inosine, Hx, xanthine, and uric acid excretion were also measured before and for 24 hours after exercise. During the first 120 minutes of recovery, plasma Hx concentrations, as well as the urinary Hx and xanthine excretion rates, were higher (P < .05) with allopurinol compared with the placebo trial. In contrast, plasma uric acid concentration and urinary uric acid excretion rates were lower (P < .05) with allopurinol. The total urinary excretion of purines (inosine + Hx + xanthine + uric acid) above basal levels was higher in the allopurinol trial compared with placebo. These results indicate that the total urinary purine excretion after intermittent sprint exercise was enhanced with allopurinol treatment. Furthermore, the composition of urinary purines was markedly affected by this drug.

Highlights from the tennis Australia heritage collections : mini-exhibition in the player cafe, Rod Laver Arena

Summary : This 'mini-exhibition' arose as an opportunity to showcase recent acquisitions as well as established holdings of significant items of tennis related heritage within the Tennis Australia Heritage Collections. In general, the Collections have two main strengths, and the mini-exhibition was designed to communicate these. The first strength is the ability to show the evolution of tennis technology and practices over time, from the beginnings of modern tennis in the 1860s, to today. This evolution is a result of tennis being influenced by changes in the wider world, such as the Industrial Revolution. The second strength of the Collections is in showing the impact and influence of tennis on society. Many items in the Collections are evidence of the immense and enduring popularity of the sport across the world. The Collections contain many beautiful, rare and fascinating items of decorative arts, fashion, literature and social history which feature tennis as a motif. These items show the reverse influence - the deep impression tennis has made outside of the sport itself.  This mini-exhibition focuses on these two themes. Some displays focus on the first theme. They demonstrate the evolution of tennis racquets, tennis balls, instructional publications and other tennis related equipment over the past century and a half. Other displays focus on the second theme. There are cases which examine tennis' influence upon global popular culture, in board games, fashion and decorative arts from around the world.  The mini-exhibition includes items from the U.s, U.K., Germany, France, Austria, Japan and Australia, demonstrating the global phenomenon that tennis quickly became, and showcasing the international scope of the Collections.  Each case contains text panels listing the objects and their specifications, and panels providing contextual information about the display. The miniexhibition is expected to be on display until November 2009. A case-bycase breakdown of objects, with images and a layout map follows.

Influence of pacing on reliability of middle-distance cycling performance

The purpose of the present study was to examine the reliability of middle distance cycling time trials using fast-, even-, and slow-starts. Eighteen endurance-trained male cyclists [mean ± standard deviation; VO2peak 63.1 ± 6.1 mL⋅kg-1⋅min-1] performed nine cycling time trials where the total external work (96.5 ± 11.2 kJ) was identical to the better of two, 5-minute habituation time trials. Power output during the first quarter of the time-trials (24.1 ± 2.8 kJ) was fixed to induce fast-, even- or slow-starting strategies (60, 75 and 90 s, respectively). In consecutive sessions, participants performed three trials of each pacing condition although the order of these pacing conditions was counterbalanced. Average power output and performance time were unaffected by trial number in the fast- (P = 0.60), even- (P = 0.18) and slow-start (P = 0.53) trials. In all three pacing conditions, average power output was highly reliable and similar between trial 1 to 2 and trial 2 to 3 in fast- (standard error of measurement; SEM=8.3 and 8.2W), even (coefficient of variation; CV=2.8 and 2.4%) and slow-start (CV=2.4 and 1.5%) trials. In conclusion, the reproducibility of 5-min cycling time trials is unaffected by starting strategy and is acceptable following two selfpaced habituation trials. Research examining the influence of pacing strategies may therefore be conducted without the need for familiarisation trials using each individual pacing condition.

Influence of thermal and mechanical stresses on the strength of intact and relined denture bases

Statement of problem. Denture bases may become increasingly weaker as a result of thermal stress and flexural cyclic loading. Information regarding this potential problem and its relationship to the denture base reline is limited.Purpose. This study evaluated the influence of thermal and mechanical stresses on the strength of intact and relined denture bases.Material and methods. Twenty-eight microwave-polymerized (Acron MC) intact denture bases were prepared in the shape of a 3-mm-thick maxillary denture. Additionally, fifty-six 2-mm-thick denture bases were relined with 1 mm of autopolymerizing resin (Tokuyama Rebase Fast II or New Truliner) (n = 28). Intact and relined specimens were divided into 4 groups (n = 7) as follows: without stress (control); a mechanical stress at 0.8 Hz for 10,000 cycles; 5000 thermal cycles between 5 degrees C and 55 degrees C; or a combination thermo-mechanical stress. The specimens were vertically loaded in compression with a rounded rod at 5 mm/min until failure, using a universal testing machine. Data on maximum fracture load (N), deflection at fracture (%), and fracture energy (N-mm) were analyzed by 2-way analysis of variance and Student-Newman-Keuls tests (alpha = .05).Results. The strength of the denture bases relined with New Truliner was not significantly affected by any of the experimental conditions, but comparing the control groups, New Truliner exhibited the lowest maximum fracture load values. The maximum fracture load of intact denture bases (P = .002) and those relined with Tokuyama Rebase Fast II (P = .01) showed a significant decrease after thermal stress. Additionally, cyclic loading significantly decreased the maximum fracture load (P < .001), deflection at fracture (P = .025), and fracture energy (P < .001) of intact denture bases and those relined with Tokuyama Rebase (P values of .002, .039, and .001, respectively).Conclusion. Thermal and mechanical stresses exert deleterious effects on the strength of intact and/or relined denture bases, which vary according to the relining material used.

Influence of consumption of probiotics on presence of enterobacteria in the oral cavity

Clinical benefits of probiotics have been clearly reported in different gastrointestinal disorders, many of them caused by enterobacteria. The oral cavity is a port of entry and can be an important reservoir of these microorganisms. This work evaluated whether consumption of probiotics was able to influence the presence of enterobacteria in the oral cavity and the specific secretory response against these microorganisms. Saliva samples of healthy individuals were collected and plated in Mac-Conkey agar. Carriers of Gram-negative, rod-shaped microorganisms in the oral cavity were selected and instructed to use the probiotic Yakult LB for 20 days. Saliva was then collected and enterobacteria species were identified using the API 20 E system and by ELISA using anti-enterobacteria IgA. The results showed reduction in the prevalence of enterobacteria, but no significant changes in enterobacterial counts (log CFU/mL; p = 0.3457). The species most frequently isolated were Enterobacter cloacae and Klebsiella oxytoca, both before and after probiotic consumption. No significant changes were observed in anti-enterobacteria IgA levels. In conclusion, probiotic consumption had some influence on enterobacterial presence in the oral cavity, but did not affect enterobacterial counts or the specific immune secretory response against them.