Solid propellant processing factors in rocket motor design.

At head of title: NASA space vehicle design criteria (chemical propulsion).

Solid rocket motor nozzles /

"...written by Russell A. Ellis."

Final report on development and fabrication of high strength simulated rocket motor cases by cryogenic stretch forming process. Technical documentary report nr. AFML-TR-64-410.

"MM Project nr. 8-101."

Organizational maintenance manual (including repair parts and special tools lists) : 2.75-inch low spin, folding fin aircraft rockets, 66-mm light antitank weapon systems, 3.5-inch rockets, and M3A2E1 rocket motor (JATO).

"June 1973."

Direct support and general support maintenance manual (including repair parts and special tools list) for 2.75-inch low spin, folding fin aircraft rockets, 66-mm light antitank weapon systems, 3.5-inch rockets and M3A2E1 rocket motor (JATO).

"August 1974."

Organizational maintenance manual (including repair parts and special tools lists) : 2.75-inch low spin, folding fin aircraft rockets, 66-mm light antitank weapon systems, 3.5-inch rockets, and M3A2E1 rocket motor (JATO).

"June 1973."

Caracterização de juntas soldadas em PAW e GTAW de chapas finas em aço maraging 300 submetidas a vários reparos

Pós-graduação em Engenharia Mecânica - FEG

Modeling re-ignition and chuffing in solid rocket motors

A nonlinear model is developed to numerically simulate dynamic combustion inside a solid rocket motor chamber. Using this model, the phenomena of re-ignition and chuffing are investigated under low-L* conditions. The model consists of two separate submodels (coupled to each other), one for unsteady burning of propellant and the other for unsteady conservation of mass and energy within the chamber. The latter yields instantaneous pressure and temperature within the chamber. The instantaneous burning rate is calculated using a one-dimensional, nonlinear, transient gas-phase model previously developed by the authors. The results presented in this paper show that the model predicts not only the critical L*, but also the various regimes of L*-instabihty. Specifically, the results exhibit (1) amplifying pressure oscillations leading to extinction, and (2) re-ignition after a dormant period following extinction. The re-ignition could be observed only when a radiation heat flux (from the combustion chamber to the propellant surface) was included. Certain high-frequency oscillations, possibly due to intrinsic instability, are observed when the pressure overshoots during re-ignition. At very low values of initial L*, successive cycles of extinction/reignition displaying typical characteristics of chuffing are predicted. Variations of the chuffing frequency and the thickness of propellant burned off during a chuff with L* are found to be qualitatively the same as that reported from experimental observations.

Processing and characterization of ablative composites used in rocket motors

The main objective of this research work was to obtain two formulations of ablative composites. These composites are also known as ablative structural composites, for applications in atmospherically severe conditions according to the high-temperature, hot gaseous products flow generated from the burning of solid propellants. The formulations were manufactured with phenolic resin reinforced with chopped carbon fiber. The composites were obtained by the hot compression molding technique. Another purpose of this work was to conduct the physical and chemical characterization of the matrix, the reinforcements and the composites. After the characterization, a nozzle divergent of each formulation was manufactured and its performance was evaluated through the rocket motor static firing test. According to the results found in this work, it was possible to observe through the characterization of the raw materials that phenolic resins showed peculiarities in their properties that differentiate one from the other, but did not exhibit significant differences in performance as a composite material for use in ablation conditions. Both composites showed good performance for use in thermal protection, confirmed by firing static tests (rocket motor). Composites made with phenolic resin and chopped carbon fiber showed that it is a material with excellent resistance to ablation process. This composite can be used to produce nozzle parts with complex geometry or shapes and low manufacturing cost.

Stabilisation of isocyanate cross linked polybutadiene binder

Isocyanate cross-linked hydroxy terminated polybutadiene is used as a binder for solid rocket propellant. Rocket motors containing this propellant require a storage life of at least 20 years. During storage it has been found that the important rubbery properties of the binder can be lost due to oxidative cross-linking of the polybutadiene chains. This could cause catastrophic failure when the rocket motor is required. At present the bis-hindered phenol Calco 2246 is used as a thermal oxidative stabiliser, but it's performance is only adequate. This has led to the search for a more efficient stabiliser system. To hasten the evaluation of new antioxidant systems the use of dynamic thermal analysis was investigated. Results showed that a tentative relationship existed between predictions by thermal analysis and the long term oven ageing for simple single antioxidant systems. But for more complex systems containing either autosynergistic or mixed antioxidants no relationship was observed suggesting that results for such an "accelerated" technique cannot be used for the purpose of extrapolation for long term performance. This was attributed to the short time and more aggressive condition used (hjgher temperature and oxygen rich atmosphere in thermal analysis) altering the mechanism of action of the antioxidants and not allowing time for co-operative effect of the combined antioxidant system to form. One potential problem for the binder system is the use of an diisocyanate as a cross-linking agent. This reacts with the hydroxyl hydrogen on the polymer as well as other active hydrogens such as those contained in a number of antioxidants, affecting both cross-linking and antioxidant effectiveness. Studies in this work showed that only antioxidants containing amine moieties have a significant affect on binder preparation, with the phenolic antioxidants not reacting. This is due to the greater nucleophilicity of the amines. Investigation of a range of antioxidant systems, including potentially homo, hetero and autosynergistic systems, has highlighted a number of systems which show considerably greater effectiveness than the currently used antioxidant Calco 2246. The only single antioxidant which showed improvement was the partially unhindered phenol y-Tocopherol. Of the mixed systems combinations of the sulphur containing antioxidants e.g. DLTP with higher levels of chain-breaking antioxidants, especially Calco 2246, were the most promising. Also the homosynergistic mix of an aromatic amine and a phenol was seen to be very effective but the results were inconsistent. This inconsistency could be explained by the method of sample preparation used. It was shown that the efficiency of a number of antioxidant.s could be dramatically improved by the use of ultrasound during the mixing stage of preparation. The reason for this increase in performance is unclear but in the case of the homosynergistic amine/phenol mix both more efficient mixing and/or the production of a novel mechanism of action are suggested

The SCRAMSPACE I scramjet flight design and construction

The design activities of the development of the SCRAMSPACE I scramjet-powered free-flight experiment are described in this paper. The objectives of this flight are first described together with the definition of the primary, secondary and tertiary experiments. The Scramjet configuration studied is first discussed together with the rocket motor system selected for this flight. The different flight sequences are then explained, highlighting the SCRAMSPACE I free-flyer separation and re-orientation procedures. A design trade-off study is then described considering vehicle stability, packaging, thermo-structural analysis and trajectory, discussing the alignment of the predicted performance with the mission scientific requirements. The global system architecture and instrumentation of the vehicle are then explained. The conclusions of this design phase are that a vehicle design has been produced which is able to meet the mission scientific goals and the procurement & construction of the vehicle are ongoing.

Instability of Combustion

THE following equations governing the phenomenon of intrinsic instability of combustion, leading to low frequency oscillations in a rocket motor using a single liquid propellant, were derived and investigated by L. Crocco.

固体火箭发动机柔性接头弹性件力学性能研究

针对固体火箭发动机柔性接头中的橡胶材料，研究了在进行这种橡胶结构有限元计算中橡胶材料的力学行为的表征。进行了单轴拉伸与简单剪切材料力学性能试验，根据不同材料模型对试验曲线进行了拟合，并用MSC／Marc软件模拟了超弹性材料的单轴拉伸与简单剪切变形过程。结果表明：采用单轴拉伸试验数据预测材料剪切性能会造成明显误差，而简单剪切试验得到的模型可以比较准确描述材料的拉伸和剪切变形，针对柔性接头这种以剪切变形为主的结构，应选取剪切试验数据；当应变大于150％时，不同材料模型与试验数据的选用范围对计算结果具有明显影响。

应用于固体火箭发动机喷管出口羽流温度测量的光学辐射高温计

利用辐射光谱测量温度的原理,设计并制造了一种新型的非接触式光学辐射高温计.详细介绍该温度计的基本原理和标定方法,并将该温度计应用于火箭发动机喷管出口羽流的温度测量中,初步的实验结果和数值模拟结果相一致.

固体火箭发动机喷管气固两相流动的数值模拟

对颗粒相采用颗粒轨道模型,气相求解可压缩N-S方程组,计算方法采用显式Runge-Kutta时间推进法与有总变差衰减(TVD)性质的高精度MUSCL-Roe格式;自主开发了曲线坐标系下二维轴对称可压缩N-S方程组的解算器Solve2D,研究了固体火箭发动机喷管中颗粒相对流场的影响以及不同尺寸颗粒运动规律.结果表明:颗粒相对流场的影响主要表现在喷管喉部以及扩张段,和单相流场相比,沿轴线马赫数减小,且颗粒尺寸越小减少得越多;沿轴线气相温度升高,且颗粒尺寸越小温度升高越多;颗粒尺寸越小,无粒子区越小;颗粒越大与收缩段壁面碰撞越剧烈,无粒子区越大.