Anaerobic retting of banana and arecanut wastes in a plug flow digester for recovery of fiber, biogas and compost

Leaves and leaf sheath of banana and areca husk (Areca catechu) constitute an important component of urban solid waste (USW) in India which are difficult to degrade under normal windrow composting conditions. A successful method of anaerobic digestion built around the fermentation properties of these feedstock has been evolved which uses no moving parts, pretreatment or energy input while enabling recovery of four products: fiber, biogas, compost and pest repellent. An SRT of 27 d and 35 d was found to be optimum for fiber recovery for banana leaf and areca husk, respectively. Banana leaf showed a degradation pattern different from other leaves with slow pectin-1 degradation (80%) and 40% lignin removal in 27 d SRT. Areca husk however, showed a degradation pattern similar to other plant biomass. Mass recovery levels for banana leaf were fiber-20%, biogas-70% (400 ml/g TS) and compost-10%. For areca husk recovery was fiber-50%, biogas-45% (250 ml/g TS) and compost-5%. (C) 2012 Elsevier Inc. All rights reserved.

Fish and shell fish fauna of the retting and nonretting zones of the Kadinamkulam kayal, Kerala

Retting of coconut husk is one of the major problems of pollution in the estuaries (kayals) of Kerala. Retting activity has resulted in the mass destruction of the flora and fauna and has converted sizeable sections of the kayal into virtual cesspools of foul smelling stagnant waters. Levels of hydrogen sulphide, phosphate and BOD, increased while dissolved oxygen and fish and shellfish fauna decreased in the ambient waters. In the Kadinamkulam kayal a total of 37 species of fishes belonging to 26 families, 5 species of prawn and 2 species each of crabs and molluscs were recorded from the no retting zone, whereas only 20 species of fish in dead condition were collected from the rating zone. Prawns, crabs and molluscs were absent at the vetting zone. Majority of the fish fauna in the kayal were marine forms.

Polyphenolic Compounds Liberated during Coir Retting in a Bio-reactor: Separation, Characterisation and Possible Applications

School of environmental studies, Cochin University of Science and Technology

Development of microbial treatment of ret liquor generated in a coir retting bioreactor

School of Environmental Studies, Cochin University of Science and Technology

Retting Of Coconut Husk - A Unique Case Of Water Pollution On The South West Coast Of India

The extensive backwaters of Kerala are the sites for a flourishing cottage industry - the coir industry. This enterprise almost exclusively located along the 590 km coastal belt of Kerala, provides direct employment to over half a million people in the state and produces nearly 90% of the total coir goods in the world. The shallow bays and lagoons of the 30 backwater systems of the state are traditional areas for the retting of coconut husk for the production of the coir fibre. The paper examines the environmental status of the retting grounds in Kerala, in relation to the biotic communities. The study revealed that retting activity has caused large scale organic pollution along with the mass destruction of the flora and fauna, converting sizeable sections of the backwaters into virtual cesspools of foul smelling stagnant waters. High values of hydrogen sulphide, ammonia, BOD5 associated with anoxic conditions and low community diversity of plankton, benthic fauna, fish, shell fish, wood boring and fouling organisms were the outstanding feature of the retting zones.

Purification and biochemical characterization of an alkaline pectin lyase from Fusarium decemcellulare MTCC 2079 suitable for Crotolaria juncea fiber retting

An extracellular pectin lyase secreted by Fusarium decemcellulare MTCC 2079 under solid state fermentation condition has been purified to electrophoretic homogeniety by using ammonium sulfate fractionation, carboxymethyl cellulose and gel filtration (Sephadex G-100) column chromatographies. The purified enzyme showed single protein band corresponding to molecular mass 45 +/- 01 kDa on sodium dodecyl sulfate polyacrylamide gel electrophoresis. The enzyme had maximum activity at pH 9.0 and showed maximum stability in the pH range of 9.0-12.0. The optimum temperature of the purified enzyme was 50 degrees C and it showed maximum stability upto 40 degrees C. The energy of activation for the thermal denaturation (Ea) was 59.06 kJ mol(-1) K-1. The K-m and k(cat) values using citrus pectin as the substrate were 0.125mgml(-1) and 72.9 s(-1) in 100mM sodium carbonate buffer pH 9.0 at 50 degrees C. The biophysical studies on pectin lyase showed that its secondary structure belongs to alpha+beta class of protein with comparatively less of beta-sheets. Purified pectin lyase showed efficient retting of Crotolaria juncea fibers.

Microbial quality of hemp (Cannabis sativa L.) and flax (Linum usitatissimum L.) from plants to thermal insulation

Flax and hemp have traditionally been used mainly for textiles, but recently interest has also been focused on non-textile applications. Microbial quality throughout the whole processing chain of bast fibres has not previously been studied. This study concentrates on the microbial quality and possible microbial risks in the production chain of hemp and flax fibres and fibrous thermal insulations. In order to be able to utilize hemp and flax fibres, the bast fibres must be separated from the rest of the plant. Non-cellulosic components can be removed with various pretreatment processes, which are associated with a certain risk of microbial contamination. In this study enzymatic retting and steam explosion (STEX) were examined as pretreatment processes. On the basis of the results obtained in this study, the microbial contents on stalks of both plants studied increased at the end of the growing season and during the winter. However, by processing and mechanical separation it is possible to produce fibres containing less moulds and bacteria than the whole stem. Enzymatic treatment encouraged the growth of moulds in fibres. Steam explosion reduced the amount of moulds in fibres. Dry thermal treatment used in this study did not markedly reduce the amount of microbes. In this project an emission measurement chamber was developed which was suitable for measurements of emissions from both mat type and loose fill type insulations, and capable of interdisciplinary sampling. In this study, the highest amounts of fungal emissions were in the range of 10^3 10^5 cfu/m^3 from the flax and hemp insulations at 90% RH of air. The fungal emissions from stone wool, glass wool and recycled paper insulations were below 10^2 cfu/m^3 even at 90% RH. Equally low values were obtained from bast fibrous materials in lower humidities (at 30% and 80% RH of air). After drying of moulded insulations at 30% RH, the amounts of emitted moulds were in all cases higher compared to the emissions at 90% RH before drying. The most common fungi in bast fibres were Penicillium and Rhizopus. The widest variety of different fungi was in the untreated hemp and linseed fibres and in the commercial loose-fill flax insulation. Penicillium, Rhizopus and Paecilomyces were the most tolerant to steam explosion. According to the literature, the most common fungi in building materials and indoor air are Penicillium, Aspergillus and Cladosporium, which were all found in some of the bast fibre materials in this study. As organic materials, hemp and flax fibres contain high levels of nutrients for microbial growth. The amount of microbes can be controlled and somewhat decreased by the processing methods presented.

A study of the use of the trimesium salt of glyphosate to desiccate and ret flax and linseed (Linum usitatissimum) and of its effects on the yield of straw, seed and fibre

A replicated field plot experiment was carried out in Northern Ireland in 1996 with flax, cv Ariane, and linseed, cv Flanders, each grown at seed rates of 500, 1000 and 1500 seeds/m(2), in which a comparison was made between netting of the standing crop, following desiccation by the trimesium salt of glyphosate (Touchdown, Zeneca Ltd.), and water or dew retting of the pulled crop. Application at 4 litres/ha on 9 August, 33 days after the mid-point of flowering (MPF), achieved both desiccation and partial retting of the crop within 14 days. Over 16 % clean long fibre was extracted by scutching the stand-netted flax straw, yielding 800 kg/ha fibre, while water retting achieved 20 extraction and 980 kg/ha yield and dew netting 8.5 % and 420 kg/ha respectively. The dew retting was uneven, resulting in high losses during fibre extraction, while water retting for 7 days at 25 degreesC did not achieve complete retting resulting in a high content of woody fragments in the fibre. Fibre yields increased by almost 50 % with the high v. low seed rate. Linseed was less well retted than flax and contained higher levels of impurity in the extracted long fibre which, after retting, yielded 120 to 310 kg/ha at extraction rates of 2.9 % to 7.5 %.

In a second experiment in 1998 flax cvs. Viola and Evelyn were treated with the timesium salt of glyphosate at rates of 2, 4 or 6 litres/ha 10, 20, 30 or 40 days after MPF on 5 July. Viola desiccated satisfactorily at all spray dates with 4 and 6 litres/ha glyphosate. The 20-day treatment desiccated more slowly than the 30-day and the 2 litres/ha rate did not achieve complete desiccation, but the trimesium salt of glyphosate achieved better desiccation at this timing than that found in earlier studies with the original form of glyphosate. Evelyn desiccated more slowly and less evenly than Viola particularly at the 20-day and 40-day timings. Spraying at MPF + 10 days interrupted early development of the seed and fibre significantly reducing yields. Due to slower desiccation the 20-day timing was no better than the 30-day, which was well retted by harvest 44 days after spraying, and gave the highest yield of clean long fibre. The spraying 40 days after MPF was considered too late in the season to be of practical use. It was concluded that retting of standing flax following desiccation with the trimesium salt of glyphosate was more effective than with the earlier formulation and that resting of the standing crop could achieve equivalent or better retting with similar fibre yields to traditional retting methods. The optimum spray timing was found to be about 30 days after MPF with 4 or 6 litres/ha, the lower rate being adequate for glyphosate responsive varieties such as Viola.

Geochemical, Sedimentological And Remote Sensing Studies Of Kayamkulam Estuary, South West Coast Of India- A Gis Approach

In this study, an attempt has been made to find the textural, geochemical, sedimentological characteristics of sediments and water phases of the kayamkulam estuary located in the Southwest coast of Kerala, besides the impact of gas based thermal power plant located at the northern part of the estuary. Estuaries are an important stage in the transport of the solid weathering product of the earth’s crust. These weathered products or sediments are complex mixtures of a number of solid phases that may include clays, silica, organic matter, metal oxides, carbonates, sulfides and a number of minerals. Studies on the aquatic systems revealed the fact that it posses severe ecological impairments due to heavy discharge of sediments from 44 rivers, the continued disposal of pollutants rich materials from industries, sewage channels, agricultural areas and retting yards

Short Isora Fibre Reinforced Natural Rubber Composites

The present study deals with the short isora fibre reinforced natural rubber composites. In recent years there has been a tremendous advancement in the field of science and technology of short fibre reinforced polymer composites. The low density, high strength, high stiffness to weight ratio, excellent durability and design flexibility are the primary reasons for their use in many diversified fields such as air crafts, automobiles, marine industry etc. Compared to the various natural and synthetic fibres used as reinforcement for elastomer composites isora fibre is superior in many aspects. `Isora' is a natural lignocellulosic fibre which is easily available in South India especially in Kerala. The fibre is separated from the bark of the Helicteres isora plant by retting process. This fibre has excellent mechanical properties and is easily amenable to physical and chemical modifications. The study shows that composites with poor interfacial bonding tend to dissipate more energy than that with to interfacial bonding. The mechanical loss also can be related to interfacial bonding. The effect of chemical treatment of isora fibre on damping was also studied. Both in the low and high temperature region which indicates that this composite posseses low damping and hence good interfacial bonding characteristics. Hence these composites are better candidates for high damping applications. Composites with longitudinally oriented fibres showed high storage modulus than transversely oriented ones due to the effective stress transfer between fibre and matrix.

Studies on the effect of pollution, with special reference to benthos, in Cochin backwaters

Considerable number of factories and related establishments forming an industrial complex are located in the upper reaches of the estuary from Varapuzha about 10km from cochin barmouth to Alwaye while lower down are the retting grounds at Vaduthala and nearby places at about 5km from the barmouth. Muncipal wastes from the city population of over 5 lakhs effluents and solid waste from several fish processing factories and other land washings around Willington island reach the estuary move near its lower reaches close to the barmouth. Cochin estuary is the biggest in the state providing water front for the largest number of industries from the small retting grounds of Vaduthala to the huge fertilizer factories of Udyogamandal and receiving the highest quantity of town sewage and land drainage. The estuary contributes itself as nursery ground for shrimps and related fishery as well. Study of this estuary therefore contributes to a typical environment as regards to pollution problems in the tropics and hence the scope of the present investigation

Effect of industrial pollution on the benthic communities of a tropical estuary

Cochin backwaters, a tropical barbuilt estuary is well known for its prawn, molluscan and demersal fisheries. Also it formed the dumping area for sewage,235 retting of husks and discharge of effluents from industries located on either side of it. As a result the fishery is being gradually dwindled year after year due to the lowering of the water quality. The effect of industrial polution on the benthic community of this tropical estuary was worked out. An area extending over 21 km from the mouth of the estuary to upstream of industrial belt was selected. Temporal and spatial variations of 16 environmental parameters at 9 stations along the area were monitored monthly during 1981. Benthic fauna of these 9 stations consisted of amphipods , polychaetes, isopods, tanaidaceans, molluscs and other crustaceans (Decapods, Acetes, Alpheids, Balanus, insect larvae, chironomid larvae, cumacea and some fresh water forms ). Apart from these, sea anemone, flat worms, nematodes, sipunculoids, echinoderms and fishes were also encountered. 75 species belonging to 31 faunal groups were identified. Of these 31 groups, amphipods, polychaedes, isopods, tanaidaceans and molluscs were numerically abundant. Rest of the 26 groups (including 13 riverine forms) were found less significant due to their rare occurrence/low numerical abundance. Polychaetes and molluscs were the only major groups present at all the stations.

Studies On Bods And Dissolved Oxygen In The Kadinamkulam Kayal, Southern Kerala

This paper discusses the salient features associated with the variation in the BODs and dissolved oxygen concentration in the Kadinamkulam Kayal based on fortnightly data from two selected stations from October1987toSeptember1988.The BODs ranged from 5.76 to 24.39 mg/l in the surface water and from 4.96 to 22.60mg!1 in the bottom waterat station-l whereas at station-2, it ranged from 0 to 3.74mg/1 in the surface water and from 0 to 3.40 mg!l in the bottom water. The dissolved oxygen concentration ranged from 0 to 0.72 mglI in the surface water and from 0 to 0.42 mg!l in the bottom waterat station-I, At station-2 it ranged from 2.69 to 6.21mg!1 in the surface waterand from 1.97 to 5.74 mg!1 in the bottom water. The pre-monsoom period showed the highest BODsof 16.68mg!I while the monsoon period showed the lowest of 0.61 mg!I. The dissolved oxygen concentration reached its peak during the monsoon period (5.52 mg/I). Long spells of anoxic condition during the post and pre-monsoon periods was a characteristic feature of the retting zone

Primary Productivity Of The Retiing Zones In The Kadinamkulamestuary, South-West Coastof India

Retting.of coconut husk is one of the major problems of pollution in the estuaries (Kayals) of Kerala. This paper discusses the salient features associated with the variation in gross and net primary productivity values in the Kadinarnkularn Kayal based on lortnightlydala from twosclected stations frorn Octobcr1987 to September 1988.The gross primary productivity value in the surface water ranged from 0.06 to 0.29gC/m3/day at Station Iand from 0.06 to 1.49gC/rn3/dayatstation II. In the bottom wateritrangcdfrorn oto 0.21 gC/m2/ day at station I whereas that at station II from 0.03 to 1.41gC/m3j day. The net productivity in the surface water at station I varied from 0 to 024 gC/m Iday Whereas that atstation II varied from 0.02to 1.44gC/m3Iday.AI the bottomwaterilvaried from ato 0.19gC/m3/ day at station I and from 0.01 to 1.21gC/m3/day at station II. The monsoon period showed the highest mean seasonal value at stations I and II. The total depletion of dissolved oxygen giving rise to anoxic condition coupled with the production of large quantities of hydrogen sulphide was found to be detrimental to the gross and net productivity values in the retting zone