Predicting the thermal inactivation of bacteria in a solid matrix: simulation studies on the relative effects of microbial thermal resistance parameters and process conditions

A combined mathematical model for predicting heat penetration and microbial inactivation in a solid body heated by conduction was tested experimentally by inoculating agar cylinders with Salmonella typhimurium or Enterococcus faecium and heating in a water bath. Regions of growth where bacteria had survived after heating were measured by image analysis and compared with model predictions. Visualisation of the regions of growth was improved by incorporating chromogenic metabolic indicators into the agar. Preliminary tests established that the model performed satisfactorily with both test organisms and with cylinders of different diameter. The model was then used in simulation studies in which the parameters D, z, inoculum size, cylinder diameter and heating temperature were systematically varied. These simulations showed that the biological variables D, z and inoculum size had a relatively small effect on the time needed to eliminate bacteria at the cylinder axis in comparison with the physical variables heating temperature and cylinder diameter, which had a much greater relative effect. (c) 2005 Elsevier B.V All rights reserved.

Simplified procedure to estimate the resistance parameters of transmission lines

An alternative and simplified procedure is described to estimate the longitudinal resistances of transmission lines based on the real-time load profile. This method proposes to estimate the resistance parameters from the synchronized measurements of complex currents and complex voltages at the sending and receiving ends of transmission systems. The synchronized measurements can be in practice obtained using phasor measurement units (PMUs). © 2012 Springer-Verlag Berlin Heidelberg.

Effects of excessive energy intake and supplementation with chromium propionate on insulin resistance parameters in nonlactating dairy cows

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Methods to determine resistance to anthelmintics when continuing larval development occurs

The in vivo faecal egg count reduction test (FECRT) is the most commonly used test to detect anthelmintic resistance (AR) in gastrointestinal nematodes (GIN) of ruminants in pasture based systems. However, there are several variations on the method, some more appropriate than others in specific circumstances. While in some cases labour and time can be saved by just collecting post-drench faecal worm egg counts (FEC) of treatment groups with controls, or pre- and post-drench FEC of a treatment group with no controls, there are circumstances when pre- and post-drench FEC of an untreated control group as well as from the treatment groups are necessary. Computer simulation techniques were used to determine the most appropriate of several methods for calculating AR when there is continuing larval development during the testing period, as often occurs when anthelmintic treatments against genera of GIN with high biotic potential or high re-infection rates, such as Haemonchus contortus of sheep and Cooperia punctata of cattle, are less than 100% efficacious. Three field FECRT experimental designs were investigated: (I) post-drench FEC of treatment and controls groups, (II) pre- and post-drench FEC of a treatment group only and (III) pre- and post-drench FEC of treatment and control groups. To investigate the performance of methods of indicating AR for each of these designs, simulated animal FEC were generated from negative binominal distributions with subsequent sampling from the binomial distributions to account for drench effect, with varying parameters for worm burden, larval development and drench resistance. Calculations of percent reductions and confidence limits were based on those of the Standing Committee for Agriculture (SCA) guidelines. For the two field methods with pre-drench FEC, confidence limits were also determined from cumulative inverse Beta distributions of FEC, for eggs per gram (epg) and the number of eggs counted at detection levels of 50 and 25. Two rules for determining AR: (1) %reduction (%R) < 95% and lower confidence limit <90%; and (2) upper confidence limit <95%, were also assessed. For each combination of worm burden, larval development and drench resistance parameters, 1000 simulations were run to determine the number of times the theoretical percent reduction fell within the estimated confidence limits and the number of times resistance would have been declared. When continuing larval development occurs during the testing period of the FECRT, the simulations showed AR should be calculated from pre- and post-drench worm egg counts of an untreated control group as well as from the treatment group. If the widely used resistance rule 1 is used to assess resistance, rule 2 should also be applied, especially when %R is in the range 90 to 95% and resistance is suspected.

Effects of oat bran and nutrition counseling on the lipid and glucose profile and anthropometric parameters of hypercholesterolemia patients

Background: In order to prevent chronic, non communicable disease, it is essential that lifestyle is modified to include a diet high in fiber. Aim: To assess the effect oat bran (OB) in conjunction with nutrition counseling (NC) have on lipid and glucose profile, anthropometric parameters, quality of diet, and ingestion of ultraprocessed foods (UPF) and additives in hypercholesterolemia sufferers. Method: This was a 90-day, double-blind, placebo-controlled, block-randomized trial undertaken on 132 men and women with LDL-c ≥ 130 mg/dL. The participants were sorted into two groups: OB Group (OBG) and Placebo Group (PLG), and were given NC and 40g of either OB or rice flour, respectively. Lipid and glucose profile were assessed, as were the anthropometric data, quality of diet (Diet Quality Index revised for the Brazilian population - DQI-R) and whether or not UPF or additives were consumed. Results: Both groups showed a significant decrease in anthropometric parameters and blood pressure, as well as a significant reduction in total and LDL cholesterol. There was also an improvement in DQI-R in both groups and a decrease in consumption of UPF. Blood sugar, HOMA-IR and QUICKI values were found to be significantly lower only in the OBG. Conclusion: Our findings in lipid profile and anthropometric parameters signify that NC has a beneficial effect, which is attributable to the improved quality of diet and reduced consumption of UPF. Daily consumption of 40 g of OB was found to be of additional benefit, in decreasing insulin-resistance parameters.

Efeito do uso de salbutamol nas propriedades mecânicas do sistema respiratório de indivíduos saudáveis, tabagistas e portadores de doença pulmonar obstrutiva crônica

A doença pulmonar obstrução crônica (DPOC) é caracterizada pela limitação de fluxo parcialmente reversível, classificada por níveis de obstrução pós-broncodilatador. Há várias evidências de que o FEV1 sozinho não é capaz de mostrar a broncodilatação de pacientes com DPOC, mesmo naqueles que apresentam melhora clínica. A técnica de oscilações forçadas (TOF) tem mostrado alta sensibilidade na detecção precoce de alterações mecânicas na DPOC, contudo o efeito broncodilatador na impedância respiratória de pacientes com DPOC ainda não está esclarecido. Objetiva avaliar a utilidade da TOF nos diferentes estágios de obstrução das vias aéreas; (2) avaliar a resposta da impedância respiratória ao salbutamol em indivíduos saudáveis ao exame espirométrico e pacientes com DPOC em diferentes graus de gravidade. Foram avaliados 25 indivíduos saudáveis sem história de tabagismo, 24 tabagistas e 151 pacientes com DPOC classificados em graus I, II, III e IV. Todos os sujeitos foram avaliados pela TOF seguida da espirometria, antes e após o uso do salbutamol spray. As curvas de resistência e reatância demonstraram alteração em todos os estágios de obstrução das vias aéreas após o uso do salbutamol. O grupo de risco apresentou alterações mecânicas semelhantes ao grupo leve (p=ns). Os parâmetros R0, Rm, Csr,din e Z4Hz apresentam desempenho diagnóstico adequado (AUC > 0,85) em todos os estágios de gravidade da doença. Todos os parâmetros de TOF e espirometria apresentaram diminuição após uso do salbutamol. Os indivíduos saudáveis apresentaram uma pequena diminuição comparada aos subgrupos de DPOC. A variação em termos absolutos da ΔZ4Hz e das derivadas da resistência, ΔR0, ΔRm, ΔS, apresentaram variação significativa (p<0,0001, p<0,003; p<0,04; p<0,0002, respectivamente) com o aumento da obstrução brônquica. Nas derivadas da reatância o ΔXm aumentou com a gravidade da doença (p<0,0002). Por outro lado, a ΔCrs,dyn não demonstrou diferença significativa com a gravidade da DPOC. Em termos percentuais os parâmetros da TOF apresentaram variação expressiva em ΔRm% (p<0,02), ΔS% (p<0,02) e ΔXm% (p<0,004) com o aumento da obstrução nas vias aéreas. Por outro lado, ΔR0%, ΔCrs,dyn% e ΔZ4Hz% não variaram entre os estágios da DPOC. A associação entre a broncodilatação nas vias aéreas e a impedância pulmonar foi fraca entre ΔXm vs ΔFVC (r=0,32, p<0,0001) e ΔZ4Hz% vs ΔFEV1% vs ΔFVC% (r=0.28, p<0,0005; r=0,29, p<0,0003, respectivamente). A TOF é útil na avaliação das alterações mecânicas nos diferentes níveis de obstrução das vias aéreas na DPOC. Demonstramos o benefício da medicação broncodilatadora, quantificando a melhora da ventilação através da TOF. A impedância respiratória diminui em todos os estágios da DPOC, o estágio leve melhorou tanto quanto o estágio muito grave. Isto sugere que a medida da impedância pulmonar não é dependente do volume como ocorre na espirometria e que a broncodilatação ocorre em todas as fases da progressão da DPOC.

Avaliação da função endotelial em mulheres jovens portadoras da síndrome dos ovários policísticos

A síndrome dos ovários policísticos é uma desordem frequente e complexa, com grande variabilidade fenotípica, predominando os sinais de disfunção ovariana. Alterações metabólicas, inflamatórias e vasculares vinculadas à resistência à insulina são muito prevalentes nessa desordem podendo manifestar-se precocemente. O objetivo principal deste estudo foi investigar a presença de alterações microvasculares em mulheres jovens e não obesas portadoras da síndrome dos ovários policísticos, através de videocapilaroscopia periungueal e dosagem dos níveis séricos de endotelina-1. O objetivo secundário foi verificar a existência de associações entre os achados vasculares, níveis séricos de androgênios, parâmetros clínicos, bioquímicos, metabólicos e inflamatórios relacionados ao risco cardiovascular. Em estudo observacional, transverso e controlado avaliamos 12 mulheres com diagnóstico de síndrome dos ovários policísticos, segundo os critérios estabelecidos pelo consenso de Rotterdam e nove voluntárias saudáveis. A idade (22,82,3 X 24,62,7), o índice de massa corporal (22,53,4 X 23,73,1) e a circunferência da cintura (7510,1 X 77,38,1) foram semelhantes nos dois grupos. As portadoras da síndrome apresentavam hiperandrogenismo clínico. Não foram observadas diferenças significativas entre os grupos quando analisados os níveis séricos de estradiol, testosterona total, androstenediona ou o índice de testosterona livre, entretanto a SHBG mostrou-se significativamente mais baixa no grupo de estudo (p=0,011). A glicemia de jejum, insulina, HOMA-IR e o perfil lipídico foram normais e sem diferença entre os grupos. A amostra com síndrome dos ovários policísticos não apresentava intolerância à glicose ou Diabetes Mellitus pelo teste oral de tolerância à glicose. Os níveis séricos dos marcadores inflamatórios (leucócitos, ácido úrico, adiponectina, leptina e proteína c reativa) e do marcador de função endotelial avaliado também foram similares nos dois grupos. A velocidade de deslocamento das hemácias no basal e após oclusão foram significativamente menores nas pacientes de estudo (p=0,02), mas o tempo para atingir a VDHmax e os parâmetros relativos à morfologia e densidade capilar foram semelhantes. Não observamos correlação entre a velocidade de deslocamento das hemácias e níveis plasmáticos de endotelina-1, androgênios ou parâmetros de resistência insulínica. A velocidade de deslocamento das hemácias associou-se positivamente aos níveis plasmáticos de estradiol (r= 0,45, p<0,05) e negativamente aos de colesterol total e LDL colesterol (r= -0,52, p<0,05; r=-0,47, p<0,05, respectivamente). Em conclusão nossos resultados fornecem evidência adicional de dano precoce à função microvascular em mulheres portadoras de síndrome dos ovários policísticos. Através da capilaroscopia periungueal dinâmica, demonstramos que mulheres jovens com moderado hiperandrogenismo, sem obesidade, RI, hipertensão ou dislipidemia, já apresentam disfunção microvascular nutritiva, caracterizada por redução na velocidade de fluxo das hemácias no basal e após oclusão. Estes achados micro-circulatórios não foram acompanhados de elevações nos níveis plasmáticos de endotelina-1.

Spezifität der quantitativen Resistenz von Blättern und Früchten der Tomate (Lycopersicon ssp. L.) gegenüber Phytophthora infestans (Mont.) de Bary.

Ziel der vorliegenden Arbeit war es, einen Beitrag zur Resistenzforschung bei Tomaten gegenüber P. infestans zu leisten, um erste Grundlagen für eine mögliche Züchtungsstrategie auf Basis unterschiedlicher quantitativer Resistenzen zu erarbeiten. Hierzu wurde untersucht, inwieweit unterschiedliche qualitative und quantitative Resistenzen bei Tomatenblättern und -früchten vorliegen, und ob hierfür verantwortliche Mechanismen identifiziert werden können. Zudem wurde untersucht, ob isolatspezifische quantitative Resistenzen identifiziert werden können. Zu diesem Zweck wurde mit einer erweiterten Clusteranalyse, basierend auf einer modifizierten Sanghvi-T2 Distanz, ein statistisches Verfahren entwickelt, welches die Identifikation von quantitativen, isolatspezifischen Resistenzen unter der Berücksichtigung der Variabilität ermöglicht. Des weiteren wurde geprüft, inwieweit zwischen den Resistenzausprägungen auf dem Blatt und den Resistenzausprägungen auf der Frucht ein Zusammenhang besteht und inwieweit die im Labor beobachteten Resistenzen unter Freilandbedingungen eine Rolle spielen. Im Labortest wurde die qualitative und quantitative Blattresistenz von 109 Akzessionen aus elf Lycopersicon und Solanum Arten gegenüber zwölf unterschiedlich aggressiven und teilweise auch unterschiedlich virulenten P. infestans Isolaten untersucht (Kap. 3). Die Früchte von 38 Tomatensorten wurden auf ihre Resistenz gegenüber drei P. infestans Isolaten geprüft. Zusätzlich wurde der Einfluss der Fruchtnachreife auf die Resistenzeigenschaften der Tomatenfrüchte gegenüber P. infestans analysiert (Kap. 4). Insgesamt 40 Sorten wurden auch unter Feldbedingungen auf Blatt- und Fruchtbefall untersucht (Kap. 5). Die frühen Stadien der Infektion von Tomatenblättern mit P. infestans Sporangien wurden mikroskopisch bei acht Tomatensorten mit unterschiedlichen quantitativen Reaktionsprofilen und drei Isolaten untersucht (Kap. 6). Hierzu wurden die Entwicklungsstadien von P. infestans Sporangien nach 24h, 48h und 60h nach der Inokulation auf und im Blatt mit der Calcofluor und der KOH - Anilin Blau Färbung sichtbar gemacht. Das Auftreten und die Lokalisation von H2O2 im Blatt nach 48h und 60h nach der Inokulation in Reaktion auf die Infektion wurde mithilfe einer DAB (3,3′ - Diaminobenzidine) Färbung untersucht. Es wurden einige, z.T. auch wahrscheinlich neue, qualitative Blattresistenzen gegenüber P. infestans gefunden, jedoch war keine der 109 Akzessionen vollständig resistent gegenüber allen Isolaten. Für die quantitative Resistenz von Blättern lagen in vielen Fällen isolatspezifische Unterschiede vor. Die Sorte x Isolat Interaktionen konnten mit Hilfe der erweiterten Clusteranalyse erfolgreich analysiert werden und die Akzessionen in Gruppen mit unterschiedlichen quantitativen Resistenzprofilen bzgl. der Interaktion mit den Isolaten und des Resistenzniveaus eingeteilt werden. Für die Fruchtresistenz konnten keine qualitativen Resistenzen gegenüber den drei getesteten Isolaten gefunden werden. Im Gegensatz dazu unterschieden sich die Tomatensorten in ihrer quantitativen Resistenz und Sorten und Isolate interagierten signifikant. Auch für die Fruchtresistenz konnten Gruppen mit unterschiedlichen quantitativen Reaktionsprofilen gebildet werden. Insgesamt nimmt die Anfälligkeit von Tomatenfrüchten mit zunehmender Reife kontinuierlich und signifikant ab. Unter Laborbedingungen korrelierten nur die Sporulationskapazität der Früchte und der prozentuale Blattbefall. Im Feldversuch über zwei Jahre und mit bis zu 40 Tomatensorten war der Zusammenhang hoch signifikant, jedoch asymptotisch, d.h. bereits bei sehr geringem Blattbefall war der Fruchtbefall sehr hoch. Bei den Tomatenherkünften, die sowohl im Labor als auch im Feld auf ihre Anfälligkeit getestet wurden, erschienen die Blattanfälligkeiten ähnlich, während kein klarer Zusammenhang zwischen der Fruchtanfälligkeit im Feld und im Labor bestand. Die Entwicklung von P. infestans auf der Blattoberfläche war unabhängig von der Sorte. Sowohl beim Eindringen und der Etablierung von P. infestans ins Blatt als auch bei der damit verbunden H2O2 Aktivität im Wirt wurden deutliche isolat- und sortenspezifische Effekte gefunden, die aber nur zum Teil mit den quantitativen Unterschieden der Blattresistenz korrespondierten. Sorten, die bei hoher Resistenz unterschiedliche Reaktionsprofile aufweisen, sind grundsätzlich interessante Kreuzungspartner, um die quantitative Resistenz gegenüber P. infestans zu verbessern. Hier sind vor allem Sorten, die sich auch in ihrer H2O2 Aktivität unterscheiden von Interesse.

Análise de parâmetros de força e resistência dos músculos eretores da espinha lombar durante a realização de exercício isométrico em diferentes níveis de esforço

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Land use management in mountainous areas: combining ground-based and EO (Earth Observation) data to investigate the shallow landsliding susceptibility in the Duron valley (Trento, Italy).

Throughout the alpine domain, shallow landslides represent a serious geologic hazard, often causing severe damages to infrastructures, private properties, natural resources and in the most catastrophic events, threatening human lives. Landslides are a major factor of landscape evolution in mountainous and hilly regions and represent a critical issue for mountainous land management, since they cause loss of pastoral lands. In several alpine contexts, shallow landsliding distribution is strictly connected to the presence and condition of vegetation on the slopes. With the aid of high-resolution satellite images, it's possible to divide automatically the mountainous territory in land cover classes, which contribute with different magnitude to the stability of the slopes. The aim of this research is to combine EO (Earth Observation) land cover maps with ground-based measurements of the land cover properties. In order to achieve this goal, a new procedure has been developed to automatically detect grass mantle degradation patterns from satellite images. Moreover, innovative surveying techniques and instruments are tested to measure in situ the shear strength of grass mantle and the geomechanical and geotechnical properties of these alpine soils. Shallow landsliding distribution is assessed with the aid of physically based models, which use the EO-based map to distribute the resistance parameters across the landscape.

Formulação de pasta de cimento flexível utilizando planejamento experimental

Steam injection is an oil recovery method accomplished by introducing steam directly into the oil well to the reservoir. The steam causes dilation of the casing, which, after reduction in temperature, tends to return to the initial dimensions: causing the formation of cracks in the cement and loss of hydraulic isolation.. In this context, the type of the SBR latex is used to improve the flexibility of the cement matrix by reducing the amount of fatigue failure. To prevent these failures, the mechanical resistance parameters should be carefully adjusted to well conditions. This work aims to study the mechanical behavior of cement slurry systems additivated with SBR latex for cementing oil wells subject to steam injection. Through the central composite factorial design was studied the behavior of the compressive strength by varying the density of the paste between 1.75 g /cm³ (14.6 lb/ Gal) and 1.89 g/cm³ (15,8lb / Gal), curing time between 4 days and 28 days and concentration of SBR Latex between 0 L / m³ and 534.722 L / m³ (0 gpc and 4 gpc). The results showed that increasing the concentration of SBR latex, within the given ranges, there was a decreased compression resistance and elastic modulus by increasing the elastic deformability of the slurry. From the results it can determine best slurries formulation conditions in oil well cementing operations subject to steam injection.

Formulação de pasta de cimento flexível utilizando planejamento experimental

Steam injection is an oil recovery method accomplished by introducing steam directly into the oil well to the reservoir. The steam causes dilation of the casing, which, after reduction in temperature, tends to return to the initial dimensions: causing the formation of cracks in the cement and loss of hydraulic isolation.. In this context, the type of the SBR latex is used to improve the flexibility of the cement matrix by reducing the amount of fatigue failure. To prevent these failures, the mechanical resistance parameters should be carefully adjusted to well conditions. This work aims to study the mechanical behavior of cement slurry systems additivated with SBR latex for cementing oil wells subject to steam injection. Through the central composite factorial design was studied the behavior of the compressive strength by varying the density of the paste between 1.75 g /cm³ (14.6 lb/ Gal) and 1.89 g/cm³ (15,8lb / Gal), curing time between 4 days and 28 days and concentration of SBR Latex between 0 L / m³ and 534.722 L / m³ (0 gpc and 4 gpc). The results showed that increasing the concentration of SBR latex, within the given ranges, there was a decreased compression resistance and elastic modulus by increasing the elastic deformability of the slurry. From the results it can determine best slurries formulation conditions in oil well cementing operations subject to steam injection.

Evaluation of Fracture Parameters by Double-G, Double-K Models and Crack Extension Resistance for High Strength and Ultra High Strength Concrete Beams

This paper presents the advanced analytical methodologies such as Double- G and Double - K models for fracture analysis of concrete specimens made up of high strength concrete (HSC, HSC1) and ultra high strength concrete. Brief details about characterization and experimentation of HSC, HSC1 and UHSC have been provided. Double-G model is based on energy concept and couples the Griffith's brittle fracture theory with the bridging softening property of concrete. The double-K fracture model is based on stress intensity factor approach. Various fracture parameters such as cohesive fracture toughness (4), unstable fracture toughness (K-Ic(c)), unstable fracture toughness (K-Ic(un)) and initiation fracture toughness (K-Ic(ini)) have been evaluated based on linear elastic fracture mechanics and nonlinear fracture mechanics principles. Double-G and double-K method uses the secant compliance at the peak point of measured P-CMOD curves for determining the effective crack length. Bi-linear tension softening model has been employed to account for cohesive stresses ahead of the crack tip. From the studies, it is observed that the fracture parameters obtained by using double - G and double - K models are in good agreement with each other. Crack extension resistance has been estimated by using the fracture parameters obtained through double - K model. It is observed that the values of the crack extension resistance at the critical unstable point are almost equal to the values of the unstable fracture toughness K-Ic(un) of the materials. The computed fracture parameters will be useful for crack growth study, remaining life and residual strength evaluation of concrete structural components.

Effect of electrical parameters on morphology and in-vitro corrosion resistance of plasma electrolytic oxidized films formed on zirconium

The objective of the present work is to study the effect of electrical process Parameters (duty cycle and frequency) on morphological, structural, and in-vitro corrosion characteristics of oxide films formed on zirconium by plasma electrolytic oxidation in an electrolyte system consisting of 5 g/L of trisodium orthophosphate. The oxide films fabricated on zirconium by systematically varying the duty cycle and frequency are characterized for its phase composition, surface morphology, chemical composition, roughness, wettability, surface energy, scratch resistance, corrosion resistance, apatite forming ability and osteoblast cell adhesion. X-ray diffraction pattern of all the oxide films showed the predominance of m-ZrO2 phase. Dense and uniform films with thickness varying from 9 to 15 mu m and roughness in the range of 0.62 to 1.03 mu m are formed. Porosity of oxide films is found to be increased with an increase infrequency. The water contact angle results demonstrated that the oxide films exhibited similar hydrophilicity to zirconium substrate. All oxide films showed improved corrosion resistance, as indicated by far lower corrosion current density and passive corrosion potential compared to the zirconium substrate in simulated body fluid environment, and among the four different combinations of duty cycle and frequency employed in the present study, the oxide film formed at 95% duty cycle and 50 Hz frequency (HDLF film) showed superior pitting corrosion resistance, which can be attributed to its pore free morpholOgy. Scratch test results showed that the HDLF oxide film adhered firmly to the substrate by developing a notable scratch resistance at 19.5 +/- 1.2.N. Besides the best corrosion resistance and scratch retistance, the HDLF film also showed good apatite forming ability and osteo sarcoma cell adhesion on its surface. The HDLF oxide film on zirconium with superior surface characteristics is believed to be useful for various types of implants in the dental and orthopedic fields. (C) 2015 Elsevier B.V. All rights reserved.