A mechanical analysis of asphalt recycled mixtures produced with high recycling rates

In this work four asphalt mixtures were compared in terms of mechanical characteristics. One of the mixtures (control mixture) was used as a reference to the study of three mixtures produced with reclaimed asphalt pavement (RAP). One of the recycled mixtures incorporated 30% of RAP and the other two were produced with 50% of RAP. The effect of using a rejuvenator additive (3% rejuvenator) was also evaluated in one of the mixtures with 50% of RAP.

The Socially Optimal Recycling Rate: Evidence from Japan

This paper estimates the average social cost of municipal waste management as a function of the recycling rate. Social costs include all municipal costs and revenues, costs to recycling households to prepare materials estimated with an original method, external disposal costs, and external recycling benefits. Results suggest average social costs are minimized with recycling rates well below observed and mandated levels in Japan. Cost-minimizing municipalities are estimated to recycle less than the optimal rate. These results are robust to changes in the components of social costs, indicating that Japan and perhaps other developed countries may be setting inefficiently high recycling goals. (C) 2014 Elsevier Inc. All rights reserved.

Waste Stream Investigation from Perspective of Changing Waste Legislation at Green Sand Foundries

The update of the Finnish legislation concerning waste was unavoidable, to comply with the European Union (EU) requirements defined in the EU-Directive on Waste. The new waste law updates were enacted into the Finnish legislation on the 11.03.2011 and targeted for applicability by the 11.03.2012. This thesis investigates the implications of the new amendments to the waste legislation from the perspective of green sand foundries. The investigations are conducted by comparing two of Componenta’s green sand foundries and evaluating their waste streams. Additionally, the impacts of legislation amendments are critiqued on their environmental and economic aspects. The study’s comparison of waste fractions at the two foundries reveals that sand is dominant in absolute tonnage and costs. The increments of waste taxes forces foundries to focus on waste management, recycling and disposing. The new legislation’s promotion of material efficiency, also guides foundries towards the prevention of waste. A potential preventive measure is to regenerate waste sand resulting to cost savings on both raw-materials and waste management. However, the lack of absolute targets for waste prevention or recycling rates discourages the interests towards creating or adopting new technologies and methods for the waste handling.

Waste Management in Commercial Activity: State-of-the-Art and the Potential Innovation in the Urban Areas of Hanoi, Vietnam

As the rapid development of the society as well as the lifestyle, the generation of commercial waste is getting more complicated to control. The situation of packaging waste and food waste – the main fractions of commercial waste in different countries in Europe and Asia is analyzed in order to evaluate and suggest necessary improvements for the existing waste management system in the city of Hanoi, Vietnam. From all waste generation sources of the city, a total amount of approximately 4000 tons of mixed waste is transported to the composting facility and the disposal site, which emits a huge amount of 1,6Mt of GHG emission to the environment. Recycling activity is taking place spontaneously by the informal pickers, leads to the difficulty in managing the whole system and uncertainty of the overall data. With a relative calculation, resulting in only approximately 0,17Mt CO2 equivalent emission, incinerator is suggested to be the solution of the problem with overloaded landfill and raising energy demand within the inhabitants.

The value of a saved tree : The lifecycle of CO2-emissions associated with the combination of printing paper and electricity production of wood in the U.S. and Sweden

The pulp- and paper production is a very energy intensive industry sector. Both Sweden and the U.S. are major pulpandpaper producers. This report examines the energy and the CO2-emission connected with the pulp- and paperindustry for the two countries from a lifecycle perspective.New technologies make it possible to increase the electricity production in the integrated pulp- andpaper mill through black liquor gasification and a combined cycle (BLGCC). That way, the mill canproduce excess electricity, which can be sold and replace electricity produced in power plants. In thisprocess the by-products that are formed at the pulp-making process is used as fuel to produce electricity.In pulp- and paper mills today the technology for generating energy from the by-product in aTomlinson boiler is not as efficient as it could be compared to the BLGCC technology. Scenarios havebeen designed to investigate the results from using the BLGCC technique using a life cycle analysis.Two scenarios are being represented by a 1994 mill in the U.S. and a 1994 mill in Sweden.The scenariosare based on the average energy intensity of pulp- and paper mills as operating in 1994 in the U.S.and Sweden respectively. The two other scenarios are constituted by a »reference mill« in the U.S. andSweden using state-of-the-art technology. We investigate the impact of varying recycling rates and totalenergy use and CO2-emissions from the production of printing and writing paper. To economize withthe wood and that way save trees, we can use the trees that are replaced by recycling in a biomassgasification combined cycle (BIGCC) to produce electricity in a power station. This produces extra electricitywith a lower CO2 intensity than electricity generated by, for example, coal-fired power plants.The lifecycle analysis in this thesis also includes the use of waste treatment in the paper lifecycle. Both Sweden and theU.S. are countries that recycle paper. Still there is a lot of paper waste, this paper is a part of the countries municipalsolid waste (MSW). A lot of the MSW is landfilled, but parts of it are incinerated to extract electricity. The thesis hasdesigned special scenarios for the use of MSW in the lifecycle analysis.This report is studying and comparing two different countries and two different efficiencies on theBLGCC in four different scenarios. This gives a wide survey and points to essential parameters to specificallyreflect on, when making assumptions in a lifecycle analysis. The report shows that there arethree key parameters that have to be carefully considered when making a lifecycle analysis of wood inan energy and CO2-emission perspective in the pulp- and paper mill in the U.S. and in Sweden. First,there is the energy efficiency in the pulp- and paper mill, then the efficiency of the BLGCC and last theCO2 intensity of the electricity displaced by BIGCC or BLGCC generatedelectricity. It also show that with the current technology that we havetoday, it is possible to produce CO2 free paper with a waste paper amountup to 30%. The thesis discusses the system boundaries and the assumptions.Further and more detailed research, including amongst others thesystem boundaries and forestry, is recommended for more specificanswers.

Desenvolvimento e caracterização de compósitos poli(tereftalato de etileno) reciclado (PET reciclado) com flocos de vidro.

The growing concern with the solid residues management, observed in the last decade, due to its huge amount and impact, has motivated the search for recycling processes, where these residues can be reprocessed to generate new products, enlarging the cycle of materials and energy which are present. Among the polymeric residues, there is poly (ethylene terephthalate) (PET). PET is used in food packaging, preferably in the bottling of carbonated beverages. The reintegration of post-consumer PET in half can be considered a productive action mitigation of environmental impacts caused by these wastes and it is done through the preparation of several different products at the origin, i.e. food packaging, with recycling rates increasing to each year. This work focused on the development and characterization mechanical, thermal, thermo-mechanical, dynamic mechanical thermal and morphology of the pure recycled PET and recycled PET composites with glass flakes in the weight fraction of 5%, 10% and 20% processed in a single screw extruder, using the following analytical techniques: thermogravimetry (TG), differential scanning calorimetry (DSC), tensile, Izod impact, Rockwell hardness, Vicat softening temperature, melt flow rate, burn rate, dynamic mechanical thermal analysis (DMTA) and scanning electron microscopy (SEM). The results of thermal analysis and mechanical properties leading to a positive evaluation, because in the thermograms the addition of glass flakes showed increasing behavior in the initial temperatures of thermal decomposition and melting crystalline, Furthermore was observed growing behavior in the mechanical performance of polymer composites, whose morphological structure was observed by SEM, verifying a good distribution of glass flakes, showing difference orientation in the center and in the surface layer of test body of composites with 10 and 20% of glass flakes. The results of DMTA Tg values of the composites obtained from the peak of tan ä showed little reductions due to poor interfacial adhesion between PET and recycled glass flakes.

O desenvolvimento da indústria da reciclagem dos materiais no Brasil: motivação econômica ou benefício ambiental conseguido com a atividade?

A indústria de reciclagem vem se desenvolvendo no Brasil desde o começo dos anos noventa, o que resulta em elevados índices de reciclagem e tecnologia de ponta na reciclagem de alguns materiais. Requisitada como estratégia para a gestão dos resíduos no destino final, a reciclagem possui a particularidade de ser uma atividade econômica bastante rentável. Este artigo analisa os índices da indústria de reciclagem dos materiais no Brasil. Com base nos resultados obtidos através da consulta bibliográfica e dados estatísticos oriundos de fontes primárias e secundárias, conclui-se que a atividade da reciclagem dos materiais no Brasil se presta a satisfazer exclusivamente às demandas econômicas do setor. Neste sentido, a contribuição ambiental da reciclagem perde relevância visto que o crescimento da atividade está condicionado às demandas da cadeia produtiva industrial

Comparative Anylysis of Recyling Programs: A Case Study of Three Universities

Abstract The goal of this study was to conduct a comparative analysis of three university recycling programs. This study looked at several aspects of the programs that included the diversion rates, per capita ratios of materials recycled and disposed, and the average net costs of waste disposal and waste diversion. The universities included in this study were the University of Nebraska-Lincoln, the University of Colorado at Boulder, and the University of Oregon. To gather the information necessary for this analysis, I contacted each of the university’s recycling coordinators. To determine the average net costs of waste disposal and waste diversion I requested both the recycling budget and solid waste budget from each university for the fiscal years of interest which included: 2006-2007, 2007-2008, and 2008-2009. To calculate the diversion rates and per capita ratios, I requested performance records from each university listing the tonnage of materials recycled and disposed for the same years. This study’s findings reported that the average net costs for waste diversion in all three universities were $22-$122 less per ton than costs for waste collection and disposal. This study also indicated that the universities with the highest diversion and recycling rates were the University of Colorado at Boulder and the University of Oregon. The university with the lowest waste generated per capita was the University of Oregon followed by the University of Nebraska-Lincoln.

Evaluating Bucknell's Waste Stream

This thesis examines three questions regarding the content of Bucknell University‟s waste stream and the contributors to campus recycling and solid waste disposal. The first asks, “What does Bucknell‟s waste stream consist of?” To answer this question, I designed a campus-wide waste audit procedure that sampled one dumpster from each of the eleven „activity‟ types on campus in order to better understand Bucknell‟s waste composition. The audit was implemented during the Fall semester of the 2011-2012 school year. The waste from each dumpster was sorted into several recyclable and non-recyclable categories and then weighed individually. Results showed the Bison and Carpenter Shop dumpsters to contain the highest percentage of divertible materials (through recycling and/or composting). When extrapolated, results also showed the Dining Services buildings and Facilities buildings to be the most waste dense in terms of pounds of waste generated per square foot. The Bison also generated the most overall waste by weight. The average composition of all dumpsters revealed that organic waste composed 24% of all waste, 23% was non-recyclable paper, and 20% was non-recyclable plastic. It will be important to move forward using these results to help create effective waste programs that target the appropriate areas of concern. My second question asks, “What influences waste behavior to contribute to this „picture‟ of the waste stream?” To answer this question, I created a survey that was sent out to randomly selected sub-group of the university‟s three constituencies: students, faculty, and staff. The survey sought responses regarding each constituency‟s solid waste disposal and recycling behavior, attitudes toward recycling, and motivating factors for solid waste disposal behaviors across different sectors of the university. Using regression analysis, I found three statistically significant motivating factors that influence solid waste disposal behavior: knowledge and awareness, moral value, and social norms. I further examined how a person‟s characteristics associate to these motivating factors and found that one‟s position on campus proved a significant association. Consistently, faculty and staff were strongly influenced by the aforementioned motivating factors, while students‟ behavior was less influenced by them. This suggests that new waste programs should target students to help increase the influence of these motivators to improve the recycling rate and lower overall solid waste disposal on campus. After making overall conclusions regarding the waste audit and survey, I ask my third question, which inquires, “What actions can Bucknell take to increase recycling rates and decrease solid waste generation?” Bucknell currently features several recycling and waste minimization programs on campus. However, using results from the waste audit and campus survey, we can better understand what are the issues of the waste stream, how do we go about addressing these issues, and who needs to be addressed. I propose several suggestions for projects that future students may take on for summer or thesis research. Suggestions include targeting the appropriate categories of waste that occur most frequently in the waste stream, as well as the building types that have the highest waste density and potential recovery rates. Additionally, certain groups on campus should be targeted more directly than others, namely the student body, which demonstrates the lowest influence by motivators of recycling and waste behavior. Several variables were identified as significant motivators of waste and recycling behavior, and could be used as program tactics to encourage more effective behavior.

The role of automated sorting in the recovery of aluminium alloys waste

Selected papers from the 3rd Edition of the International Conference on Wastes: Solutions, Treatments and Opportunities

Desenvolvimento e caracterização de compósitos poli(tereftalato de etileno) reciclado (PET reciclado) com flocos de vidro.

The growing concern with the solid residues management, observed in the last decade, due to its huge amount and impact, has motivated the search for recycling processes, where these residues can be reprocessed to generate new products, enlarging the cycle of materials and energy which are present. Among the polymeric residues, there is poly (ethylene terephthalate) (PET). PET is used in food packaging, preferably in the bottling of carbonated beverages. The reintegration of post-consumer PET in half can be considered a productive action mitigation of environmental impacts caused by these wastes and it is done through the preparation of several different products at the origin, i.e. food packaging, with recycling rates increasing to each year. This work focused on the development and characterization mechanical, thermal, thermo-mechanical, dynamic mechanical thermal and morphology of the pure recycled PET and recycled PET composites with glass flakes in the weight fraction of 5%, 10% and 20% processed in a single screw extruder, using the following analytical techniques: thermogravimetry (TG), differential scanning calorimetry (DSC), tensile, Izod impact, Rockwell hardness, Vicat softening temperature, melt flow rate, burn rate, dynamic mechanical thermal analysis (DMTA) and scanning electron microscopy (SEM). The results of thermal analysis and mechanical properties leading to a positive evaluation, because in the thermograms the addition of glass flakes showed increasing behavior in the initial temperatures of thermal decomposition and melting crystalline, Furthermore was observed growing behavior in the mechanical performance of polymer composites, whose morphological structure was observed by SEM, verifying a good distribution of glass flakes, showing difference orientation in the center and in the surface layer of test body of composites with 10 and 20% of glass flakes. The results of DMTA Tg values of the composites obtained from the peak of tan ä showed little reductions due to poor interfacial adhesion between PET and recycled glass flakes.

Agonist-induced internalization and recycling of the glucagon-like peptide-1 receptor in transfected fibroblasts and in insulinomas.

Glucagon-like peptide-1 (GLP-1) is the most potent stimulator of glucose-induced insulin secretion and its pancreatic beta-cell receptor is a member of a new subfamily of G-protein-coupled receptors which includes the receptors for vasoactive intestinal polypeptide, secretin and glucagon. Here we studied agonist-induced GLP-1 receptor internalization in receptor-transfected Chinese hamster lung fibroblasts using three different approaches. First, iodinated GLP-1 bound at 4 degrees C to transfected cells was internalized with a t 1/2 of 2-3 min following warming up of the cells to 37 degrees C. Secondly, exposure to GLP-1 induced a shift in the distribution of the receptors from plasma membrane-enriched to endosomes-enriched membrane fractions, as assessed by Western blot detection of the receptors using specific antibodies. Thirdly, continuous exposure of GLP-1 receptor-expressing cells to iodinated GLP-1 led to a linear accumulation of peptide degradation products in the medium following a lag time of 20-30 min, indicating a continuous cycling of the receptor between the plasma membrane and endosomal compartments. Potassium depletion and hypertonicity inhibited transferrin endocytosis, a process known to occur via coated pit formation, as well as GLP-1 receptor endocytosis. In contrast to GLP-1, the antagonist exendin-(9-39) did not lead to receptor endocytosis. Surface re-expression following one round of GLP-1 receptor endocytosis occurred with a half-time of about 15 min. The difference in internalization and surface re-expression rates led to a progressive redistribution of the receptor in intracellular compartments upon continuous exposure to GLP-1. Finally, endogenous GLP-1 receptors expressed by insulinoma cells were also found to be internalized upon agonist binding. Together our data demonstrate that the GLP-1 receptor is internalized upon agonist binding by a route similar to that taken by single transmembrane segment receptors. The characterization of the pathway and kinetics of GLP-1-induced receptor endocytosis will be helpful towards understanding the role of internalization and recycling in the control of signal transduction by this receptor.

Mechanisms of internalization and recycling of the chemokine receptor, CCR5

CCR5 is a G protein-coupled receptor that binds several natural chemokines but it is also a coreceptor for the entry of M tropic strains of HIV-1 into cells. Levels of CCR5 on the cell surface are important for the rate of HIV-1 infection and are determined by a number of factors including the rates of CCR5 internalization and recycling. Here we investigated the involvement of the actin cytoskeleton in the control of ligand-induced internalization and recycling of CCR5. Cytochalasin D, an actin depolymerizing agent, inhibited chemokine-induced internalization of CCR5 and recycling of the receptor in stably transfected CHO cells and in the monocytic cell line, THP-1. CCR5 internalization and recycling were inhibited by Toxin B and C-3 exoenzyme treatment in CHO and THP-1 cells, confirming activation of members of the RhoGTPase family by CCR5. The specific Rho kinase inhibitor Y27632, however, had no effect on CCR5 internalization or recycling. Ligand-induced activation of CCR5 leads to Rho kinase-dependent formation of focal adhesion complexes. These data indicate that CCR5 internalization and recycling are regulated by actin polymerization and activation of small G proteins in a Rho-dependent manner.

Transition metal rates in latosol twice treated with sewage sludge

A reciclagem agrícola do lodo de esgoto tem provocado o acúmulo de metais pesados no solo e na água, podendo atingir níveis tóxicos e causar danos às plantas cultivadas, aos animais e ao homem, por meio da cadeia trófica. Neste intuito foi desenvolvido o presente experimento, em condições de campo, entre 2000 e 2002, onde foram avaliados os efeitos da aplicação de lodo de esgoto por dois anos, sobre a extração de metais de transição (essenciais e não) pelo extrator DTPA em um Latossolo Vermelho distrófico (LVd) de textura média. As concentrações dos elementos metálicos: Mn, Fe, Cd, Ni, Co, Pb e Cr não foram detectados pelo método da absorção atômica na solução obtida com o extrator DTPA. A aplicação de lodo de esgoto causou inicialmente pequena elevação no pH do solo, posteriormente a diminuição do mesmo, e manteve-se próximo ao original. Foi possível concluir que, com a aplicação consecutiva do lodo, os teores extraíveis de Fe e Mn nas amostras de solos aumentaram gradativamente nos dois anos agrícolas, com as doses do lodo de esgoto aplicado, época de amostragens, e foram superiores ao tratamento testemunha. O extrator apresentou capacidade restrita para avaliação da fitodisponibilidade dos metais pesados decorrentes das baixas concentrações nas amostras de solo.