Lap belt angle measurement in adjustable rear seats: procedure development and vehicle survey. Final report.

National Highway Traffic Safety Administration, Washington, D.C.

Study of older child restraint/booster seat fit and NASS injury analysis. Final report.

National Highway Traffic Safety Administration, Washington, D.C.

Booster seat evaluation: belt anchorage location effect and performance in rear-facing seats. Final report.

Mode of access: Internet.

Test and evaluation of head restraints, seat backs, and anchorages in vehicles subjected to rear impact collision. Final report.

National Highway Traffic Safety Administration, Washington, D.C.

Announcement and legislation enactment improve children’s seating position in regional areas

New legislation requires all children 7 years and younger to use child-specific Australian Standards approved restraints suitable to their age and restricts seating young children in the front of cars. Observations of child seating position and restraint use were undertaken in Toowoomba and Rockhampton before the Queensland legislation was announced (T1), after the announcement but before it was enacted (T2) and after it came into force (T3). From T1 to T2, the percentage of children seated in the rear increased (69% to 75%), with a further increase from T2 to T3 (75% to 77%). This pattern was clear when there were one or two children in the car, but not when there were 3 or more. The effect on restraint use was more complex. After the announcement (T2) the percentage of children using adult seatbelts significantly increased regardless of the number of child passengers. However, once the legislation was enacted (T3) there was a significant increase in the percentage of children using child seats/boosters where there was one or two child passengers. Where there were three or more children in the vehicle there was little change in restraint choice between pre (T1) and post (T3) legislation.

Patterns of correlation between vehicle occupant seat pressure and anthropometry

Seat pressure is known as a major factor of seat comfort in vehicles. In passenger vehicles, there is lacking research into the seat comfort of rear seat occupants. As accurate seat pressure measurement requires significant effort, simulation of seat pressure is evolving as a preferred method. However, analytic methods are based on complex finite element modeling and therefore are time consuming and involve high investment. Based on accurate anthropometric measurements of 64 male subjects and outboard rear seat pressure measurements in three different passenger vehicles, this study investigates if a set of parameters derived from seat pressure mapping are sensitive enough to differentiate between different seats and whether they correlate with anthropometry in linear models. In addition to the pressure map analysis, H-Points were measured with a coordinate measurement system based on palpated body landmarks and the range of H-Point locations in the three seats is provided. It was found that for the cushion, cushion contact area and cushion front area/force could be modeled by subject anthropometry,while only seatback contact area could be modeled based on anthropometry for all three vehicles. Major differences were found between the vehicles for other parameters.

Brake system performance requirements of a lightweight electric/hybrid rear wheel drive vehicle

Investigates the braking performance requirements of the UltraCommuter, a lightweight series hybrid electric vehicle currently under development at the University of Queensland. With a predicted vehicle mass of 600 kg and two in-wheel motors each capable of 500 Nm of peak torque, decelerations up to 0.46 g are theoretically possible using purely regenerative braking. With 99% of braking demands less than 0.35 g, essentially all braking can be regenerative. The wheel motors have sufficient peak torque capability to lock the rear wheels in combination with front axle braking, eliminating the need for friction braking at the rear. Emergency braking levels approaching 1 g are achieved by supplementation with front disk brakes. This paper presents equations describing the peak front and rear axle braking forces which occur under straight line braking, including gradients. Conventionally, to guarantee stability, mechanical front/rear proportioning of braking effort ensures that the front axle locks first. In this application, all braking is initially regenerative at the rear, and an adaptive ''by-wire'' proportioning system presented ensures this stability requirement is still satisfied. Front wheel drive and all wheel drive systems are also discussed. Finally, peak and continuous performance measures, not commonly provided for friction brakes, are derived for the UltraCommuter's motor capability and range of operation.

Reducing rear-end crashes with cooperative systems

This paper presents an evaluation of the effectiveness of a cooperative Intelligent Transport System (C-ITS) to reduce rear-end crashes. Two complementary simulation techniques are used to demonstrate the benefits of the C-ITS. A traffic (VEINS) and sensor (SiVIC) simulations use realistic data related to traffic/road in Brisbane’s Pacific Motorway, driver’s reaction time and injury severity to evaluate benefits. The results of our simulations show that C-ITS could reduce rear-end crash risk by providing several seconds of additional warning to drivers.

Measuring in-vehicle child comfort to study barriers to appropriate and correct use of restraints

Traffic crashes are the leading cause of death and injury among children aged between 4-14 years1,2 and premature graduation to adult seat belts2,3 and restraint misuse4 are common and known risk factors. Children are believed to prematurely graduate to adult belts and misuse the seat belt in booster seats if uncomfortable2,5,6. Although research has concentrated on educating parents and designing better restraints to reduce errors in use, comfort of the child in the restraint has not been studied. Currently there is no existing method for studying comfort in children in restraint systems, although self-report survey tools and pressure distribution mapping is commonly used to measure comfort among adult in vehicle seats. This poster presents preliminary results from work aimed at developing an appropriate method to measure comfort of children in vehicle restraint systems. The specific aims are to: 1. Examine the potential of using modified adult self-report/survey and pressure distribution mapping in children 2. Develop a video based, objective measure of comfort in children.

Sale of men's seats for 3 years

Digital image

Opinion of Whitehead Hicks regarding distribution of synagogue seats

Digital image

Book listing seats leased in synagogue

Digital image