An experimental test of rainfall as a control agent of Glycaspis brimblecombei Moore (Hemiptera, Psyllidae) on seedlings of Eucalyptus camaldulensis Dehn (Myrtaceae)

An experimental test of rainfall as a control agent of Glycaspis brimblecombei Moore (Hemiptera, Psyllidae) on seedlings of Eucalyptus camaldulensis Dehn (Myrtaceae). Glycaspis brimblecombei is one the greatest threats to eucalyptus plantations in Brazil. The effects of rainfall to reduce the abundance of lerp of Glycaspis brimblecombei on experimentally infested seedlings of Eucalyptus camaldulensis were assessed. The number of lerps on the adaxial and abaxial surfaces of every leaf of 60 seedlings was recorded, before and after submission to the following treatments: "artificial rain", "leaf wetting" and control. A drastic reduction in lerp abundance per plant was observed after the treatments "leaf wetting" and artificial rain (F = 53.630; p < 0.001), whereas lerp abundance remained roughly constant in the control treatment along the experiment (F = 1.450; p = 0.232). At the end of the experiment, lerp abundance was significantly lower in both the "artificial rain" and "leaf wetting" than in the control treatment. Two days of rainfall simulation were sufficient to decrease more than 50% of the lerp population, with almost 100% of effectiveness after 5 days of experiment. Our results indicate that lerp solubilization and mechanical removal by water are potential tools to the population regulation of G. brimblecombei on E. camaldulensis seedlings.

Dynamic hydrological modeling in drylands with TRMM based rainfall

This paper introduces and evaluates DryMOD, a dynamic water balance model of the key hydrological process in drylands that is based on free, public-domain datasets. The rainfall model of DryMOD makes optimal use of spatially disaggregated Tropical Rainfall Measuring Mission (TRMM) datasets to simulate hourly rainfall intensities at a spatial resolution of 1-km. Regional-scale applications of the model in seasonal catchments in Tunisia and Senegal characterize runoff and soil moisture distribution and dynamics in response to varying rainfall data inputs and soil properties. The results highlight the need for hourly-based rainfall simulation and for correcting TRMM 3B42 rainfall intensities for the fractional cover of rainfall (FCR). Without FCR correction and disaggregation to 1 km, TRMM 3B42 based rainfall intensities are too low to generate surface runoff and to induce substantial changes to soil moisture storage. The outcomes from the sensitivity analysis show that topsoil porosity is the most important soil property for simulation of runoff and soil moisture. Thus, we demonstrate the benefit of hydrological investigations at a scale, for which reliable information on soil profile characteristics exists and which is sufficiently fine to account for the heterogeneities of these. Where such information is available, application of DryMOD can assist in the spatial and temporal planning of water harvesting according to runoff-generating areas and the runoff ratio, as well as in the optimization of agricultural activities based on realistic representation of soil moisture conditions.

Solute transport by surface runoff from low-angle slopes: theory and application

The removal of chemicals in solution by overland how from agricultural land has the potential to be a significant source of chemical loss where chemicals are applied to the soil surface, as in zero tillage and surface-mulched farming systems. Currently, we lack detailed understanding of the transfer mechanism between the soil solution and overland flow, particularly under field conditions. A model of solute transfer from soil solution to overland flow was developed. The model is based on the hypothesis that a solute is initially distributed uniformly throughout the soil pore space in a thin layer at the soil surface. A fundamental assumption of the model is that at the time runoff commences, any solute at the soil surface that could be transported into the soil with the infiltrating water will already have been convected away from the area of potential exchange. Solute remaining at the soil surface is therefore not subject to further infiltration and may be approximated as a layer of tracer on a plane impermeable surface. The model fitted experimental data very well in all but one trial. The model in its present form focuses on the exchange of solute between the soil solution and surface water after the commencement of runoff. Future model development requires the relationship between the mass transfer parameters of the model and the time to runoff: to be defined. This would enable the model to be used for extrapolation beyond the specific experimental results of this study. The close agreement between experimental results and model simulations shows that the simple transfer equation proposed in this study has promise for estimating solute loss to surface runoff. Copyright (C) 2000 John Wiley & Sons, Ltd.

Experimental examination of solute transport by surface runoff from low-angle slopes

The removal of chemicals in solution, by overland flow from agricultural land has the potential to be a significant source of chemical loss from zero-till and surface mulched farming systems. The objective of this study was to determine the magnitude of solute loss by surface runoff from agricultural systems. Previous experiments have enhanced the understanding of the exchange process, but the initial soil conditions together with the tracer application method in these experiments have meant that in some cases the results have limited applicability to field situations. In this study, two different sets of experiments were carried out to determine the magnitude of solute loss by surface runoff. These experiments entailed the surface application of bromide to (1) field scale plots 18 m long by 2 m wide and (2) repacked soil cores 236 mm in diameter; followed by the application of simulated rainfall in both cases. The most substantial finding of the field experiments was that the quantities of solute in surface runoff varied greatly with soil type and structure (0.07-14.9% of the applied bromide). Also, on some soils, large quantities of tracer were measured in the surface runoff even after several hours of infiltration. The experiments on soil cores showed that soil structure plays an important role in the quantity of chemical that may be transported in the surface runoff. These field results showed that, in certain systems, solute movement by overland flow is an important transport mechanism, which should be considered when budgeting for chemical loss. (C) 2000 Elsevier Science B.V. All rights reserved.

Micromorphological study of slumping in a hardsetting seedbed under various wetting conditions

Slumping of hardsetting seedbeds upon wetting has not been extensively studied despite the likelihood that it determines the physical properties after drying. Slumping results from processes similar to those involved in crusting except that overburden pressure can dominate rather than rainfall kinetic energy. Only a few studies have dealt with the morphological description of slumping. To simulate different climatic and management conditions, repacked seedbeds of a hardsetting sandy-loam soil were subjected to a range of wetting conditions, e.g. capillary rise, immersion, and rainfall simulation. Slumping processes were characterized using qualitative and quantitative micromorphological observations of polished blocks and thin sections from resin-impregnated samples. A morphogenetical framework was proposed to help description of the complex associations of processes which can lead to structural collapse (crusting and slumping) on wetting. Three main stages were considered, i.e. aggregate disruption or abrasion, relocation of the released material, and compaction. In the hardsetting material studied here, structural collapse under slow wetting occurred at the bottom of cores due to aggregate coalescence under overburden pressure. Coalescence required aggregate cohesion being reduced by microcracking; therefore, it differed from the coalescence previously described in unstable silty loam soils where microcracking was not necessary for aggregates to coalesce. Macroporosity decreased most strongly under fast wetting due to physical dispersion and aggregate breakdown. Under simulated rainfall, compaction by raindrops could not be distinguish from aggregate breakdown. The role of overburden pressure and of rainfall kinetic energy remains to be stated; new data are required including measurement of total porosity in the initial, wet, and dry states. (C) 2003 Elsevier B.V. All rights reserved.

Runoff and sediment transport in a degraded area

Gully erosion occurs by the combined action of splash, sheetwash and rill-wash (interrill and rill erosion). These erosion processes have a great capacity for both sediment production and sediment transport. The objectives of this experiment were to evaluate hydrological and sediment transport in a degraded area, severely dissected by gullies; to assess the hydraulic flow characteristics and their aggregate transport capacity; and to measure the initial splash erosion rate. In the study area in Guarapuava, State of Paraná, Brazil (lat 25º 24' S; long 51º24' W; 1034 m asl), the soil was classified as Cambissolo Húmico alumínico, with the following particle-size composition: sand 0.116 kg kg-1; silt 0.180 kg kg-1; and clay 0.704 kg kg-1. The approach of this research was based on microcatchments formed in the ground, to study the hydrological response and sediment transport. A total of eight rill systems were simulated with dry and wet soil. An average rainfall of 33.7 ± 4.0 mm was produced for 35 to 54 min by a rainfall simulator. The equipment was installed, and a trough was placed at the end of the rill to collect sediments and water. During the simulation, the following variables were measured: time to runoff, time to ponding, time of recession, flow velocity, depth, ratio of the initial splash and grain size. The rainsplash of dry topsoil was more than twice as high as under moist conditions (5 g m-2 min-1 and 2 g m-2 min-1, respectively). The characteristics of the flow hydraulics indicate transition from laminar to turbulent flow [Re (Reynolds number) 1000-2000]. In addition, it was observed that a flow velocity of 0.12 m s-1 was the threshold for turbulent flow (Re > 2000), especially at the end of the rainfall simulation. The rill flow tended to be subcritical [Fr (Froude Number) < 1.0]. The variation in hydrological attributes (infiltration and runoff) was lower, while the sediment yield was variable. The erosion in the rill systems was characterized as limited transport, although the degraded area generated an average of 394 g m-2 of sediment in each simulation.

NITROGEN LOSS BY EROSION FROM MECHANICALLY TILLED AND UNTILLED SOIL UNDER SUCCESSIVE SIMULATED RAINFALLS

The description of the fate of fertilizer-derived nitrogen (N) in agricultural systems is an essential tool to enhance management practices that maximize nutrient use by crops and minimize losses. Soil erosion causes loss of nutrients such as N, causing negative effects on surface and ground water quality, aside from losses in agricultural productivity by soil depletion. Studies correlating the percentage of fertilizer-derived N (FDN) with soil erosion rates and the factors involved in this process are scarce. The losses of soil and fertilizer-derived N by water erosion in soil under conventional tillage and no tillage under different rainfall intensities were quantified, identifying the intervening factors that increase loss. The experiment was carried out on plots (3.5 × 11 m) with two treatments and three replications, under simulated rainfall. The treatments consisted of soil with and soil without tillage. Three successive rainfalls were applied in intervals of 24 h, at intensities of 30 mm/h, 30 mm/h and 70 mm/h. The applied N fertilizer was isotopically labeled (15N) and incorporated into the soil in a line perpendicular to the plot length. Tillage absence resulted in higher soil losses and higher total nitrogen losses (TN) by erosion induced by the rainfalls. The FDN losses followed another pattern, since FDN contributions were highest from tilled plots, even when soil and TN losses were lowest, i.e., the smaller the amount of eroded sediment, the greater the percentage of FDN associated with these. Rain intensity did not affect the FDN loss, and losses were greatest after less intense rainfalls in both treatments.

Methods for assessment of pre-harvest sprouting in wheat cultivars

The objective of this work was to test methods for pre-harvest sprouting assessment in wheat cultivars. Fourteen wheat cultivars were grown in Londrina and Ponta Grossa municipalities, Paraná state, Brazil. They were sampled at 10 and 17 days after physiological maturity and evaluated using the methods of germination by rainfall simulation (in a greenhouse), in-ear grain sprouting, and grains removed from the ears. The in-ear grain sprouting method allowed the differentiation of cultivars, but showed different resistance levels from the available description of cultivars. The sprouting of grain removed from the ears did not allow a reliable distinction of data on germination in any harvest date or location. The method of rainfall simulation is the most suitable for the assessment of cultivars as to pre-harvest sprouting, regardless of the sampling date and evaluated location.

INFLUENCE OF PRECIPITATION AND SUGARCANE STRAW IN AMINOCYCLOPYRACHLOR AND INDAZIFLAM CONTROL EFFICIENCY

ABSTRACTThe raw sugarcane harvesting system has changed the dynamics of weed tillage for this crop, changing the predominant weed species and providing a barrier between the herbicide and the soil. Thus, this study has aimed to assess the influence of precipitation and sugarcane straw in the aminocyclopyrachlor and indaziflam herbicides control efficiency for the species Ipomoea trilobaand Euphorbia heterophylla. There were two trials, one for aminocyclopyrachlor and one for the indaziflam, both in the greenhouse at the campus of Faculdade Integrado in the Brazilian city of Campo Mourão, PR. Each experiment consisted of eight treatments with four replications. The treatments consisted of the combination of the presence of straw (10 t ha-1), capillary irrigation and rainfall simulation (20 mm). Assessments of control percentage of I.triloba and E.heterophylla were carried out, as well as the number of plants per pot. The aminocyclopyrachlor and indaziflam herbicides applied directly to the soil were efficient in controlling these species. The 20 mm rainfall simulation or daily irrigation on the straw are indispensable to promote the removal of aminocyclopyrachlor and indaziflam from the straw and provide satisfactory control of I.triloba and E.heterophylla.

Systematic winter sea-surface temperature biases in the northern Arabian Sea in HiGEM and the CMIP3 models

Analysis of 20th century simulations of the High resolution Global Environment Model (HiGEM) and the Third Coupled Model Intercomparison Project (CMIP3) models shows that most have a cold sea-surface temperature (SST) bias in the northern Arabian Sea during boreal winter. The association between Arabian Sea SST and the South Asian monsoon has been widely studied in observations and models, with winter cold biases known to be detrimental to rainfall simulation during the subsequent monsoon in coupled general circulation models (GCMs). However, the causes of these SST biases are not well understood. Indeed this is one of the first papers to address causes of the cold biases. The models show anomalously strong north-easterly winter monsoon winds and cold air temperatures in north-west India, Pakistan and beyond. This leads to the anomalous advection of cold, dry air over the Arabian Sea. The cold land region is also associated with an anomalously strong meridional surface temperature gradient during winter, contributing to the enhanced low-level convergence and excessive precipitation over the western equatorial Indian Ocean seen in many models.

Perdas de solo, matéria orgânica e nutrientes por erosão hídrica em uma vertente coberta com diferentes quantidades de palha de cana-de-açúcar em Guariba - SP

A erosão em entressulcos resulta da desagregação causada pelo impacto das gotas de chuva na superfície do solo e pelo transporte superficial das partículas do solo desagregadas, onde se encontram a matéria orgânica e os nutrientes fundamentais para a produção agrícola. O presente trabalho teve como objetivo avaliar as perdas de solo, matéria orgânica e nutrientes em uma vertente localizada em uma área de Latossolo Vermelho-Amarelo distrófico, cultivada com cana-de-açúcar, que é colhida mecanicamente. As parcelas experimentais foram submetidas à ação de uma chuva simulada com intensidade de 60 mm h-1, durante 65 minutos. Foram feitas análises do sedimento erodido para a determinação do volume de solução, das perdas de solo, matéria orgânica e nutrientes. Houve maiores perdas de solo, matéria orgânica e nutrientes nos sedimentos oriundos das parcelas com 0% e 25% de cobertura por palha de cana-de-açúcar. em média, essas perdas foram reduzidas nas parcelas com 75% e 100% de cobertura com palha de cana-de-açúcar. Os resultados permitiram concluir que uma cobertura com palha de cana-de-açúcar acima de 50%, da área colhida, reduz a perda de solo e de matéria orgânica, bem como diminui a concentração de nutrientes no sedimento erodido.

Perdas de solo e nutrientes por erosão num Argissolo com resíduos vegetais de cana-de-açúcar

O presente trabalho teve como objetivo determinar as perdas de solo, matéria orgânica (MO) e nutrientes (P, K, Ca e Mg) por erosão, em área cultivada com cana-de-açúcar, cuja palhada é mantida sobre a superfície do solo, localizada em Catanduva - SP, sob um Argissolo Vermelho--Amarelo. em parcelas experimentais, com 0 (CS0), 50 (CS50) e 100% (CS100) de cobertura sobre a superfície do solo, aplicou-se chuva simulada com intensidade de 60 mm h-1, durante 65 minutos. Análises do sedimento erodido indicaram taxas de enriquecimento da seguinte ordem: 2,7 a 1,9 (MO), 3,8 a 2,7 (P), 1,3 a 1,7 (K), 3,9 a 3,6 (Ca) e 2,9 a 2,6 (Mg) vezes em relação ao solo original para CS0 e CS50, respectivamente. A CS50 propiciou controle significativo da erosão de 69%, mas não reduziu a concentração de MO e nutrientes no sedimento erodido. A CS100 foi significativamente eficiente no controle da erosão (89%) e na redução das concentrações de MO (69%), P (88%), K (23%), Ca (74%) e Mg (75%) no sedimento.

Perdas de nutrientes por erosão e sua distribuição espacial em área sob cana-de-açúcar

O presente trabalho teve como objetivo principal determinar as perdas de nutrientes por erosão em entressulcos, sulcos e global (entressulcos + sulcos, A), em área cultivada com cana-de-açúcar submetida à queima da palhada na sua pré-colheita, na Fazenda Santa Bárbara, localizada em Guariba - SP, sob um Latossolo Vermelho eutroférrico (LVef). Parcelas experimentais foram submetidas à chuva simulada com intensidade de 80 mm h-1, durante 65 minutos. Análises do sedimento erodido indicaram altas taxas de enriquecimento: 1,62 (matéria orgânica, MO); 4,30 (P); 1,17 (K); 1,33 (Ca) e 1,24 (Mg) vezes em relação ao solo original. As perdas de solo e nutrientes, em função do tipo de erosão, obedeceram à seguinte ordem: sulcos > global > entressulcos. Análises geoestatísticas indicaram que as perdas de solo (A), MO, P, K e Ca por erosão apresentaram forte grau de dependência espacial, enquanto as perdas de Mg tiveram moderado grau de dependência espacial. Mapas da distribuição dos padrões de variabilidade espacial das perdas por erosão indicaram que o cultivo de cana-de-açúcar conserva as propriedades químicas e físicas do solo na maior parte da área.

Modelos para estimativa do subfator cobertura-manejo (CiII) relativo à erosão entressulcos

A análise de um modelo de erosão é um crítico passo no desenvolvimento de uma ferramenta de predição da erosão aplicável e válida; isso é crucial para avaliar o desempenho dos modelos existentes para assegurar que as estimativas de um modelo condizem com a realidade. O objetivo do presente trabalho foi avaliar modelos para a predição do subfator cobertura e manejo (CiII) relativo à erosão entressulcos. Um experimento fatorial completo foi conduzido com cinco doses de resíduo de milho (0; 0,05; 0,15; 0,40 e 0,80 kg m-2), quatro declives e duas repetições, sob condições de prévio umedecimento para determinar as taxas de erosão entressulcos (Di) e enxurrada (R). Num primeiro experimento, foi avaliada a erodibilidade entressulcos (Ki) e o subfator cobertura e manejo (CiII), em parcelas experimentais de 0,5 x 0,75 m, em solo recentemente preparado. Num segundo experimento, foram avaliados Di, R, Ki e CiII, também em parcelas de 0,5 x 0,75 m, em solo recém- preparado. Os valores de Di, R, Ki e CiII, obtidos no segundo experimento, foram utilizados na avaliação dos modelos testados. Os modelos CiII = e-2,50 CS/100 e CiII = e -2,238 CS/100 apresentaram boas estimativas para o subfator CiII.