A learning environment for robotic production line simulation

This paper presents a framework for a robotic production line simulation learning environment using Autonomous Ground Vehicles (AGV). An eLearning platform is used as interface with the simulator. The objective is to introduce students to the production robotics area using a familiar tool, an eLearning platform, and a framework that simulates a production line using AGVs. This framework allows students to learn about robotics but also about several areas of industrial management engineering without requiring an extensive prior knowledge on the robotics area. The robotic production line simulation learning environment simulates a production environment using AGVs to transport materials to and from the production line. The simulator allows students to validate the AGV dynamics and provides information about the whole materials supplying system which includes: supply times, route optimization and inventory management. The students are required to address several topics such as: sensors, actuators, controllers and an high level management and optimization software. This simulator was developed with a known open source tool from robotics community: Player/Stage. This tool was extended with several add-ons so that students can be able to interact with a complex simulation environment. These add-ons include an abstraction communication layer that performs events provided by the database server which is programmed by the students. An eLearning platform is used as interface between the students and the simulator. The students can visualize the effects of their instructions/programming in the simulator that they can access via the eLearning platform. The proposed framework aims to allow students from different backgrounds to fully experience robotics in practice by suppressing the huge gap between theory and practice that exists in robotics. Using an eLearning platform eliminates installation problems that can occur from different computers software distribution and makes the simulator accessible by all students at school and at home.

Implementation of a lean six sigma project in a production line

Companies from the motorcycles components branch are dealing with a dynamic environment, resulting from the introduction of new products and the increase of market demand. This dynamic environment requires frequent changes in production lines and requires flexibility in the processes, which can cause reductions in the level of quality and productivity. This paper presents a Lean Six Sigma improvement project performed in a production line of the company's machining sector, in order to eliminate losses that cause low productivity, affecting the fulfillment of the production plan and customer satisfaction. The use of Lean methodology following the DMAIC stages allowed analyzing the factors that influence the line productivity loss. The major problems and causes that contribute to a reduction on productivity and that were identified in this study are the lack of standardization in the setup activities and the excessive stoppages for adjustment of the processes that caused an increase of defects. Control charts, Pareto analysis and cause-and-effect diagrams were used to analyze the problem. On the improvement stage, the changes were based on the reconfiguration of the line layout as well as the modernization of the process. Overall, the project justified an investment in new equipment, the defective product units were reduced by 84% and an increase of 29% of line capacity was noticed.

Determining, Balancing and Controlling of Pitch and White Pitch at Stora Enso Kabel Production Line 4

Työn ensimmäisenä tarkoituksena oli kartoittaa kiinteä-neste ja neste-neste uuttomenetelmillä pihkan ja valkopihkan määrä Stora Enso Kabelin tuotantolinja 4:llä. Työn kannalta oli myöstärkeää saada selvyys saostumien koostumuksesta. Lopullinen päämäärä oli automatisoida fiksatiivin annostelu uuden, jatkuvatoimisen märänpäänanalysaattorin avulla. Mäntyosuuden kasvattaminen hiokemassassa lisää hydrofobisten partikkeleiden lukumäärää, minkä uskotaan lisäävän saostumariskiä. Työtä varten kehitetty neste-neste uuttomenetelmä, jota ei ole liiemmin paperiteollisuudessa käytetty, voi olla hyvä menetelmä lipofiilisten komponenttien määrän arviointiin tietyssä määrässä massa- tai prosessivesinäytettä. Virtaussytometri-menetelmän avulla tutkittiin pihka- tai valkopihkapartikkeleiden määrää ja kokojakaumaa eri prosessinäytteissä. Virtaussytometri-menetelmällä mitattujen valkopihkapartikkeleiden lukumäärän ja päällystetyn hylyn saostimen suodoksen sameuden välille löytyiselvä korrelaatio. Fiksatiivimäärän vaikutusta päällystetyn hylyn saostimen suodoksen sameuteen tutkittiin koeajojaksolla, jossa fiksatiivin annostelua säädettiin käsin. Käytetyt annosmäärät eivät riittäneet sameuden pitämiseen tasaisena matalalla tasolla.

Design of a Condition Monitoring System for a Glass Wool Production Line

Työn tarkoituksena oli suunnitella kunnonvalvontajärjestelmä kahdelle lasivillan tuotantolinjalle. Suunnitteluprosessin lisäksi työssä on esitelty erilaisia kunnonvalvontamenetelmiä. Työn alussa on kerrottu erilaisista kunnonvalvontamenetelmistä, joilla voidaan seurata erilaisten laitteiden ja koneiden toimintakuntoa.Erityisesti työssä on tarkasteltu teollisuudessa yleistyviä kunnonvalvonnan värähtelymittauksia. Työssä suunniteltu kunnonvalvontajärjestelmä perustuu viiteen eri menetelmään, jotka ovat värähtelymittaus, lämpötilanmittaus lämpökameralla, lämpötilanmittaus kannettavalla mittarilla, kuuntelu elektronisella stetoskoopilla ja pyörivien osien kunnontarkkailu stroboskoopilla. Kunnonvalvontajärjestelmän suunnittelu on tehty useassa eri vaiheessa. Ensin työssä on kartoitettu tuotannon kannalta tärkeimmät laitteet ja niiden mahdolliset vikaantumistavat. Seuraavaksi on valittu sopivat kunnonvalvontamenetelmät ja tehty mittaussuunnitelma, jossa on esitetty eri laitteille suoritettavat mittaukset ja mittausten aikavälit.Lopuksi työssä on esitelty muutama esimerkkitapaus kunnonvalvontamenetelmien käytöstä sekä kerrottu mahdollisista tulevaisuuden kehitysmahdollisuuksista.

Enhancing Customer Knowledge and Its Sharing At a Paper Production Line

This study has been made for specific paper production line at an international forest industry company in Finland. The main purpose for the study was a need to examine the current situation of the customer knowledge and its’ sharing at case production line, recognize the problems in it and finally, find out the improvement actions. The study is composed of theoretical and empirical parts. In theoretical part, knowledge management and information sharing in addition to customer knowledge management are presented. Empirical data from case production line was collected by using survey questionnaires. The results are analyzed in discussion and conclusions and finally, study ends with summary which includes recommendations. Based on the study, the amount and quality of customer knowledge and gaining and transferring the customer knowledge were found as the main challenges. The proposed solutions were discovered from moving towards more dynamic operating environment and in the area of customer knowledge management, especially from the communities of creation.

Optimization of NMP extraction in 1, 3-butadiene production line

N-methylpyrrolidone is a powerful solvent for variety of chemical processes due to its vast chemical properties. It has been used in manufacturing processes of polymers, detergents, pharmaceuticals rubber and many more chemical substances. However, it creates large amount of residue in some of these processes which has to be dealt with. Many well known methods such as BASF in rubber producing units have tried to regenerate the solvent at the end of each run, however, there is still discarding of large amount of residue containing NMP, which over time, could cause environmental concerns. In this study, we have tried to optimize regeneration of the NMP extraction from butadiene production. It is shown that at higher temperatures NMP is separated from the residue with close to 90% efficiency, and the solvent residue proved to be the most effective with a 6: 1 ratio.

The implementation of a low-cost production-line inspection system

This article describes an application of computers to a consumer-based production engineering environment. Particular consideration is given to the utilisation of low-cost computer systems for the visual inspection of components on a production line in real time. The process of installation is discussed, from identifying the need for artificial vision and justifying the cost, through to choosing a particular system and designing the physical and program structure.

Monitoring of the dissemination of Salmonella in the chicken Frankfurt-sausage production line of a sausage factory in the state of São Paulo, Brazil

Poultry meat and its derivatives are among the foodstuffs considered by environmental health authorities to present the highest risks to the public. A total of 185 samples were collected in five monthly batches, from different processing stages in a sausage plant that uses mechanically-deboned chicken meat (MDCM) and tested for the presence of Salmonella. Enrichment was carried out in both Kauffman tetrathionate broth and Rappaport-Vassiliadis broth and isolation on Salmonella-Shigella agar and brilliant-green agar. Live Salmonella bacteria were isolated from six samples of the raw meat and from the emulsion, in batches three, four and five, but not from any sample in batches one or two. The six isolated strains were all classified as Salmonella Albany, which has not previously been reported in MDCM. of the two enrichment broths, Rappaport-Vassiliadis gave the better results. The Pattern of contamination suggests a probable common source, given that a new supplier was used in the third, fourth, and fifth months. It was also shown that the industrial cooking was effective in preventing Salmonella surviving in the final product.

Crack origin and detection in thin cristallyne solar cells in a production line

In order to reduce cost and make up for the rising price of silicon, silicon wafers are sliced thinner and wider,eading to weaker wafers and increased breakage rates during fabrication process. In this work we have analysed different cracks origins and their effect on wafer’s mechanical strength. To enhance wafer’s strength some etching methods have been tested. Also, we have analysed wafers from different points of an entire standard production process. Mechanical strength of the wafers has been obtained via the four line bending test and detection of cracks has been tested with Resonance Ultrasonic Vibration (RUV) system, developed by the University of South Florida.

Module optical analyzer: Identification of defects on the production line

The usefulness of the module optical analyzer when identifying module defects on production line is presented in this paper. Two different case studies performed with two different kind of CPV modules are presented to show the use of MOA both in IES-UPM and Daido Steel facilities.

Production-line technqiue,

Mode of access: Internet.

Development of techniques to predict production line efficiency

This industrial based research project was undertaken for British Leyland and arose as a result of poor system efficiency on the Maxi and Marina vehicle body build lines. The major factors in the deterioration of system efficiency were identified as: a) The introduction of a 'Gateline' system of vehicle body build. b) The degeneration of a newly introduced measured daywork payment scheme. By relating the conclusions of past work on payment systems to the situation at Cowley, it was concluded that a combination of poor industrial relations and a lack of managerial control had caused the measured daywork scheme to degenerate into a straightforward payment for time at work. This ellminated the monetary incentive to achieve schedule with the consequence that both inefficiency and operating costs increased. To analyse further the cause of inefficiency, a study of Marina gateline stoppage logs was carried out. This revealed that poor system efficiency on the gateline was caused more by the nature of its design than poor reliability on individual items of' plant. The consideration given to system efficiency at the design stage was found to be negligible, the main obstacles being: a) A lack of understanding pertaining to the influence of certain design factors on the efficiency of a production line. b) The absence of data and techniques to predict system efficiency at the design stage. To remedy this situation, a computer simulation study of' the design factors was carried out from which relationships with system efficiency were established and empirical efficiency equations developed. Sets of tables were compiled from the equations and efficiency data relevant to vehicle body building established from the gateline stoppage logs. Computer simulation, the equations and the tables,when used in conjunction. with good efficiency data, are shown to be accurate methods of predicting production line system.efficiency.

Feed production, swine and slaughterhouse: where is the highest occupational exposure to Aspergillus spp. in this production line?

Purpose - This study intended to characterize fungal contamination in two swine farms, in one feed production unit, and also in one swine slaughterhouse. We aimed to identify where the highest occupational exposure to Aspergillus spp. was detected during the production line.

A deep learning model for controlling the galvanizing process in a production line

In the industry of steelmaking, the process of galvanizing is a treatment which is applied to protect the steel from corrosion. The air knife effect (AKE) occurs when nozzles emit a steam of air on the surfaces of a steel strip to remove excess zinc from it. In our work we formalized the problem to control the AKE and we implemented, with the R&D dept.of MarcegagliaSPA, a DL model able to drive the AKE. We call it controller. It takes as input the tuple : a tuple of the physical conditions of the process line (t,h,s) with the target value of the zinc coating (c); and generates the expected tuple of (pres and dist) to drive the mechanical nozzles towards the (c). According to the requirements we designed the structure of the network. We collected and explored the data set of the historical data of the smart factory. Finally, we designed the loss function as sum of three components: the minimization between the coating addressed by the network and the target value we want to reach; and two weighted minimization components for both pressure and distance. In our solution we construct a second module, named coating net, to predict the coating of zinc resulting from the AKE when the conditions are applied to the prod. line. Its structure is made by a linear and a deep nonlinear “residual” component learned by empirical observations. The predictions made by the coating nets are used as ground truth in the loss function of the controller. By tuning the weights of the different components of the loss function, it is possible to train models with slightly different optimization purposes. In the tests we compared the regularization of different strategies with the standard one in condition of optimal estimation for both; the overall accuracy is ± 3 g/m^2 dal target for all of them. Lastly, we analyze how the controller modeled the current solutions with the new logic: the sub-optimal values of pres and dist can be optimize of 50% and 20%.

Measuring and improving production efficiency of paint filling and packing line

Tutkittu yritys on suomalainen maaleja ja lakkoja kansainvälisesti valmistava ja myyvä toimija. Yrityksessä otettiin vuonna 2010 käyttöön uudet tuotannon ja toimitusketjun tavoitteet ja suunnitelmat ja tämä tutkimus on osa tuota kokonaisvaltaista kehittämissuuntaa. Tutkimuksessa käsitellään tuotannon ja kunnossapidon tehokkuuden parantamis- ja mittaustyökalu OEE:tä ja tuotevaihtoaikojen pienentämiseen tarkoitettua SMED -työkalua. Työn teoriaosuus perustuu lähinnä akateemisiin julkaisuihin, mutta myös haastatteluihin, kirjoihin, internet sivuihin ja yhteen vuosikertomukseen. Empiriaosuudessa OEE:n käyttöönoton ongelmia ja onnistumista tutkittiin toistettavalla käyttäjäkyselyllä. OEE:n potentiaalia ja käyttöönottoa tutkittiin myös tarkastelemalla tuotanto- ja käytettävyysdataa, jota oli kerätty tuotantolinjalta. SMED:iä tutkittiin siihen perustuvan tietokoneohjelman avulla. SMED:iä tutkittiin teoreettisella tasolla, eikä sitä implementoitu vielä käytäntöön. Tutkimustuloksien mukaan OEE ja SMED sopivat hyvin esimerkkiyritykselle ja niissä on paljon potentiaalia. OEE ei ainoastaan paljasta käytettävyyshäviöiden määrää, mutta myös niiden rakenteen. OEE -tulosten avulla yritys voi suunnata rajalliset tuotannon ja kunnossapidon parantamisen resurssit oikeisiin paikkoihin. Työssä käsiteltävä tuotantolinja ei tuottanut mitään 56 % kaikesta suunnitellusta tuotantoajasta huhtikuussa 2016. Linjan pysähdyksistä ajallisesti 44 % johtui vaihto-, aloitus- tai lopetustöistä. Tuloksista voidaan päätellä, että käytettävyyshäviöt ovat vakava ongelma yrityksen tuotannontehokkuudessa ja vaihtotöiden vähentäminen on tärkeä kehityskohde. Vaihtoaikaa voitaisiin vähentää ~15 % yksinkertaisilla ja halvoilla SMED:illä löydetyillä muutoksilla työjärjestyksessä ja työkaluissa. Parannus olisi vielä suurempi kattavimmilla muutoksilla. SMED:in suurin potentiaali ei välttämättä ole vaihtoaikojen lyhentämisessä vaan niiden standardisoinnissa.