Development of a prototype for measuring plantar forces

Studies on the distribution of plantar pressure between the sole of the foot and the ground were developed before the 19th century. Currently, the most often employed plantar pressure measurement systems are Pedar® and FScan®, which have restrictions such as operational difficulty and high cost. In the present study, a device was constructed from two pressure plates capable of measuring plantar forces in discreet areas of the feet at a low cost, using strain-gages attached to sixteen strategic points of the mechanical elements. Sixteen prismatic beams were soldered to each frame, for which the free extremity of each beam represented a specific point of the foot. Two strain gauges were attached to each beam - one near the upper fixed extremity and the other near the lower fixed extremity. Using a Wheatstone bridge electric circuit, the gauges were used to measure the force acting on the extremity of the beam. Precision and accuracy of the prototype was about 10%. In some measurements, accuracy was 2%. The low precision and accuracy were mainly due to the restrictions of the available equipment, which only permitted four measurements at a time. Thus, it was necessary for participants to stand on the plates four separate times, which signified possible changes in the position of the feet on the pressure plates. Despite some limitations, the aim was achieved. The prototype has been used in some studies and represents a contribution to biomechanics, demonstrating the viability of using strain gauges.

Inestabilidad de pórticos planos metálicos de edificación con inclusión de la flexibilidad de las uniones y elementos no prismáticos : un enfoque para la optimización

En esta tesis se aborda el problema de la modelización, análisis y optimización de pórticos metálicos planos de edificación frente a los estados límites último y de servicio. El objetivo general es presentar una técnica secuencial ordenada de optimización discreta para obtener el coste mínimo de pórticos metálicos planos de edificación, teniendo en cuenta las especificaciones del EC-3, incorporando las uniones semirrígidas y elementos no prismáticos en el proceso de diseño. Asimismo se persigue valorar su grado de influencia sobre el diseño final. El horizonte es extraer conclusiones prácticas que puedan ser de utilidad y aplicación simple para el proyecto de estructuras metálicas. La cantidad de publicaciones técnicas y científicas sobre la respuesta estructural de entramados metálicos es inmensa; por ello se ha hecho un esfuerzo intenso en recopilar el estado actual del conocimiento, sobre las líneas y necesidades actuales de investigación. Se ha recabado información sobre los métodos modernos de cálculo y diseño, sobre los factores que influyen sobre la respuesta estructural, sobre técnicas de modelización y de optimización, al amparo de las indicaciones que algunas normativas actuales ofrecen sobre el tema. En esta tesis se ha desarrollado un procedimiento de modelización apoyado en el método de los elementos finitos implementado en el entorno MatLab; se han incluido aspectos claves tales como el comportamiento de segundo orden, la comprobación ante inestabilidad y la búsqueda del óptimo del coste de la estructura frente a estados límites, teniendo en cuenta las especificaciones del EC-3. También se ha modelizado la flexibilidad de las uniones y se ha analizado su influencia en la respuesta de la estructura y en el peso y coste final de la misma. Se han ejecutado algunos ejemplos de aplicación y se ha contrastado la validez del modelo con resultados de algunas estructuras ya analizadas en referencias técnicas conocidas. Se han extraído conclusiones sobre el proceso de modelización y de análisis, sobre la repercusión de la flexibilidad de las uniones en la respuesta de la estructura. El propósito es extraer conclusiones útiles para la etapa de proyecto. Una de las principales aportaciones del trabajo en su enfoque de optimización es la incorporación de una formulación de elementos no prismáticos con uniones semirrígidas en sus extremos. Se ha deducido una matriz de rigidez elástica para dichos elementos. Se ha comprobado su validez para abordar el análisis no lineal; para ello se han comparado los resultados con otros obtenidos tras aplicar otra matriz deducida analíticamente existente en la literatura y también mediante el software comercial SAP2000. Otra de las aportaciones de esta tesis es el desarrollo de un método de optimización del coste de pórticos metálicos planos de edificación en el que se tienen en cuenta aspectos tales como las imperfecciones, la posibilidad de incorporar elementos no prismáticos y la caracterización de las uniones semirrígidas, valorando la influencia de su flexibilidad sobre la respuesta de la estructura. Así, se han realizado estudios paramétricos para valorar la sensibilidad y estabilidad de las soluciones obtenidas, así como rangos de validez de las conclusiones obtenidas. This thesis deals with the problems of modelling, analysis and optimization of plane steel frames with regard to ultimate and serviceability limit states. The objective of this work is to present an organized sequential technique of discrete optimization for achieving the minimum cost of plane steel frames, taking into consideration the EC-3 specifications as well as including effects of the semi-rigid joints and non-prismatic elements in the design process. Likewise, an estimate of their influence on the final design is an aim of this work. The final objective is to draw practical conclusions which can be handful and easily applicable for a steel-structure project. An enormous amount of technical and scientific publications regarding steel frames is currently available, thus making the achievement of a comprehensive and updated knowledge a considerably hard task. In this work, a large variety of information has been gathered and classified, especially that related to current research lines and needs. Thus, the literature collected encompasses references related to state-of-the-art design methods, factors influencing the structural response, modelling and optimization techniques, as well as calculation and updated guidelines of some steel Design Codes about the subject. In this work a modelling procedure based on the finite element implemented within the MatLab programming environment has been performed. Several keys aspects have been included, such as second order behaviour, the safety assessment against structural instability and the search for an optimal cost considering the limit states according to EC-3 specifications. The flexibility of joints has been taken into account in the procedure hereby presented; its effects on the structural response, on the optimum weight and on the final cost have also been analysed. In order to confirm the validity and adequacy of this procedure, some application examples have been carried out. The results obtained were compared with those available from other authors. Several conclusions about the procedure that comprises modelling, analysis and design stages, as well as the effect of the flexibility of connections on the structural response have been drawn. The purpose is to point out some guidelines for the early stages of a project. One of the contributions of this thesis is an attempt for optimizing plane steel frames in which both non-prismatic beam-column-type elements and semi-rigid connections have been considered. Thus, an elastic stiffness matrix has been derived. Its validity has been tested through comparing its accuracy with other analytically-obtained matrices available in the literature, and with results obtained by the commercial software SAP2000. Another achievement of this work is the development of a method for cost optimization of plane steel building frames in which some relevant aspects have been taken in consideration. These encompass geometric imperfections, non-prismatic beam elements and the numerical characterization of semi-rigid connections, evaluating the effect of its flexibility on the structural response. Hence, some parametric analyses have been performed in order to assess the sensitivity, the stability of the outcomes and their range of applicability as well.

Influence of aerodynamic characteristics of H beams on galloping stability

This paper presents the experimental study developed on a prismatic beam with H section, sometimes used in bridges as suspenders, vertical bars or decks. The purpose of this study is to understand the physical behavior of the air around this type of section, in order to reduce the aerodynamic loads, the onset speed of galloping and even to avoid it. To achieve this, a study of the influence of all geometric parameters that define the section has been developed. Previously, the most interesting configurations have been selected using a smoke flow visualization technique in the wind-tunnel, then the corresponding static aerodynamic loads were measured, completed with dynamic tests and, finally, the parameters governing the phenomenon of galloping determined.

Static and Dynamic Experimental Analysis of the Galloping Stability of Porous H-Section Beams

The phenomenon of self-induced vibrations of prismatic beams in a cross-flow has been studied for decades, but it is still of great interest due to their important effects in many different industrial applications. This paper presents the experimental study developed on a prismatic beam with H-section.The aim of this analysis is to add some additional insight into the behaviour of the flow around this type of bodies, in order to reduce galloping and even to avoid it. The influence of some relevant geometrical parameters that define the H-section on the translational galloping behaviour of these beams has been analysed. Wind loads coefficients have been measured through static wind tunnel tests and the Den Hartog criterion applied to elucidate the influence of geometrical parameters on the galloping properties of the bodies under consideration.These results have been completed with surface pressure distribution measurements and, besides, dynamic tests have been also performed to verify the static criterion. Finally, the morphology of the flow past the tested bodies has been visualised by using smoke visualization techniques. Since the rectangular section beam is a limiting case of the H-section configuration, the results here obtained are compared with the ones published in the literature concerning rectangular configurations; the agreement is satisfactory.

A computer formulation for the analysis on continuous non prismatic folded plate structures of arbitrary cross-section

A computer solution to analyze nonprismatic folded plate structures is shown. Arbitrary cross-sections (simple and multiple), continuity over intermediate supports and general loading and longitudinal boundary conditions are dealt with. The folded plates are assumed to be straight and long (beam like structures) and some simplifications are introduced in order to reduce the computational effort. The formulation here presented may be very suitable to be used in the bridge deck analysis.

Conceptual designs of multi-degree of freedom compliant parallel manipulators composed of wire-beam based compliant mechanisms

This paper proposes conceptual designs of multi-degree(s) of freedom (DOF) compliant parallel manipulators (CPMs) including 3-DOF translational CPMs and 6-DOF CPMs using a building block based pseudo-rigid-body-model (PRBM) approach. The proposed multi-DOF CPMs are composed of wire-beam based compliant mechanisms (WBBCMs) as distributed-compliance compliant building blocks (CBBs). Firstly, a comprehensive literature review for the design approaches of compliant mechanisms is conducted, and a building block based PRBM is then presented, which replaces the traditional kinematic sub-chain with an appropriate multi-DOF CBB. In order to obtain the decoupled 3-DOF translational CPMs (XYZ CPMs), two classes of kinematically decoupled 3-PPPR (P: prismatic joint, R: revolute joint) translational parallel mechanisms (TPMs) and 3-PPPRR TPMs are identified based on the type synthesis of rigid-body parallel mechanisms, and WBBCMs as the associated CBBs are further designed. Via replacing the traditional actuated P joint and the traditional passive PPR/PPRR sub-chain in each leg of the 3-DOF TPM with the counterpart CBBs (i.e. WBBCMs), a number of decoupled XYZ CPMs are obtained by appropriate arrangements. In order to obtain the decoupled 6-DOF CPMs, an orthogonally-arranged decoupled 6-PSS (S: spherical joint) parallel mechanism is first identified, and then two example 6-DOF CPMs are proposed by the building block based PRBM method. It is shown that, among these designs, two types of monolithic XYZ CPM designs with extended life have been presented.

CTCombine : rotating and combining CT data with an accurate detector model, to simulate radiotherapy portal imaging at non-zero beam angles

Established Monte Carlo user codes BEAMnrc and DOSXYZnrc permit the accurate and straightforward simulation of radiotherapy experiments and treatments delivered from multiple beam angles. However, when an electronic portal imaging detector (EPID) is included in these simulations, treatment delivery from non-zero beam angles becomes problematic. This study introduces CTCombine, a purpose-built code for rotating selected CT data volumes, converting CT numbers to mass densities, combining the results with model EPIDs and writing output in a form which can easily be read and used by the dose calculation code DOSXYZnrc. The geometric and dosimetric accuracy of CTCombine’s output has been assessed by simulating simple and complex treatments applied to a rotated planar phantom and a rotated humanoid phantom and comparing the resulting virtual EPID images with the images acquired using experimental measurements and independent simulations of equivalent phantoms. It is expected that CTCombine will be useful for Monte Carlo studies of EPID dosimetry as well as other EPID imaging applications.

Simplified numerical models of LiteSteel Beam floor joists with Web openings for the prediction of section moment capacities

This paper is aimed at investigating the effect of web openings on the plastic bending behaviour and section moment capacity of a new cold-formed steel beam known as LiteSteel beam (LSB) using numerical modelling. Different LSB sections with varying circular hole diameter and spacing were considered. A simplified but appropriate numerical modelling technique was developed for the modelling of monosymmetric sections such as LSBs subject to bending, and was used to simulate a series of section moment capacity tests of LSB flexural members with web openings. The buckling and ultimate strength behaviour was investigated in detail and the modeling technique was further improved through a comparison of numerical and experimental results. This paper describes the simplified finite element modeling technique used in this study that includes all the significant behavioural effects affecting the plastic bending behaviour and section moment capacity of LSB sections with web holes. Numerical and test results and associated findings are also presented.