Pressure filtration characteristics of enzymatically hydrolyzed biomass suspensions

Enzymatic hydrolysis of lignocellulosic polymers is likely to become one of the key technologies enabling industrial production of liquid biofuels and chemicals from lignocellulosic biomass. Certain types of enzymes are able to hydrolyze cellulose and hemicellulose polymers to shorter units and finally to sugar monomers. These monomeric sugars are environmentally acceptable carbon sources for the production of liquid biofuels, such as bioethanol, and other chemicals, such as organic acids. Liquid biofuels in particular have been shown to contribute to the reduction of net emissions of greenhouse gases. The solid residue of enzymatic hydrolysis is composed mainly of lignin and partially degraded fibers, while the liquid phase contains the produced sugars. It is usually necessary to separate these two phases at some point after the hydrolysis stage. Pressure filtration is an efficient technique for this separation. Solid-liquid separation of biomass suspensions is difficult, because biomass solids are able to retain high amounts of water, which cannot be readily liberated by mechanical separation techniques. Most importantly, the filter cakes formed from biomaterials are compressible, which ultimately means that the separation may not be much improved by increasing the filtration pressure. The use of filter aids can therefore facilitate the filtration significantly. On the other hand, the upstream process conditions have a major influence on the filtration process. This thesis investigates how enzymatic hydrolysis and related process conditions affect the filtration properties of a cardboard suspension. The experimental work consists of pressure filtration and characterization of hydrolysates. The study provides novel information about both issues, as the relationship between enzymatic hydrolysis conditions and subsequent filtration properties has so far not been considered in academic studies. The results of the work reveal that the final degree of hydrolysis is an important factor in the filtration stage. High hydrolysis yield generally increases the average specific cake resistance. Mixing during the hydrolysis stage resulted in undefined changes in the physical properties of the solid residue, causing a high filtration resistance when the mixing intensity was high. Theoretical processing of the mixing data led to an interesting observation: the average specific cake resistance was observed to be linearly proportional to the mixer shear stress. Another finding worth attention is that the size distributions of the solids did not change very dramatically during enzymatic hydrolysis. There was an observable size reduction during the first couple of hours, but after that the size reduction was minimal. Similarly, the size distribution of the suspended solids remained almost constant when the hydrolyzed suspension was subjected to intensive mixing. It was also found that the average specific cake resistance was successfully reduced by the use of filter aids. This reduction depended on the method of how the filter aids were applied. In order to obtain high filtration capacity, it is recommended to use the body feed mode, i.e. to mix the filter aid with the slurry prior to filtration. Regarding the quality of the filtrate, precoat filtration was observed to produce a clear filtrate with negligible suspended solids content, while the body feed filtrates were turbid, irrespective of which type of filter aid was used.

Development of filter media treatments for liquid filtration

Woven monofilament, multifilament, and spun yarn filter media have long been the standard media in liquid filtration equipment. While the energy for a solid-liquid separation process is determined by the engineering work, it is the interface between the slurry and the equipment - the filter media - that greatly affects the performance characteristics of the unit operation. Those skilled in the art are well aware that a poorly designed filter medium may endanger the whole operation, whereas well-performing filter media can make the operation smooth and economical. As the mineral and pulp producers seek to produce ever finer and more refined fractions of their products, it is becoming increasingly important to be able to dewater slurries with average particle sizes around 1 ¿m using conventional, high-capacity filtration equipment. Furthermore, the surface properties of the media must not allow sticky and adhesive particles to adhere to the media. The aim of this thesis was to test how the dirt-repellency, electrical resistance and highpressure filtration performance of selected woven filter media can be improved by modifying the fabric or yarn with coating, chemical treatment and calendering. The results achieved by chemical surface treatments clearly show that the woven media surface properties can be modified to achieve lower electrical resistance and improved dirt-repellency. The main challenge with the chemical treatments is the abrasion resistance and, while the experimental results indicate that the treatment is sufficiently permanent to resist standard weathering conditions, they may still prove to be inadequately strong in terms of actual use.From the pressure filtration studies in this work, it seems obvious that the conventional woven multifilament fabrics still perform surprisingly well against the coated media in terms of filtrate clarity and cake build-up. Especially in cases where the feed slurry concentration was low and the pressures moderate, the conventional media seemed to outperform the coated media. In the cases where thefeed slurry concentration was high, the tightly woven media performed well against the monofilament reference fabrics, but seemed to do worse than some of the coated media. This result is somewhat surprising in that the high initial specific resistance of the coated media would suggest that the media will blind more easily than the plain woven media. The results indicate, however, that it is actually the woven media that gradually clogs during the coarse of filtration. In conclusion, it seems obvious that there is a pressure limit above which the woven media looses its capacity to keep the solid particles from penetrating the structure. This finding suggests that for extreme pressures the only foreseeable solution is the coated fabrics supported by a strong enough woven fabric to hold thestructure together. Having said that, the high pressure filtration process seems to follow somewhat different laws than the more conventional processes. Based on the results, it may well be that the role of the cloth is most of all to support the cake, and the main performance-determining factor is a long life time. Measuring the pore size distribution with a commercially available porometer gives a fairly accurate picture of the pore size distribution of a fabric, but failsto give insight into which of the pore sizes is the most important in determining the flow through the fabric. Historically air, and sometimes water, permeability measures have been the standard in evaluating media filtration performance including particle retention. Permeability, however, is a function of a multitudeof variables and does not directly allow the estimation of the effective pore size. In this study a new method for estimating the effective pore size and open pore area in a densely woven multifilament fabric was developed. The method combines a simplified equation of the electrical resistance of fabric with the Hagen-Poiseuille flow equation to estimate the effective pore size of a fabric and the total open area of pores. The results are validated by comparison to the measured values of the largest pore size (Bubble point) and the average pore size. The results show good correlation with measured values. However, the measured and estimated values tend to diverge in high weft density fabrics. This phenomenon is thought to be a result of a more tortuous flow path of denser fabrics, and could most probably be cured by using another value for the tortuosity factor.

Washing and Dewatering of Different Starches in Pressure Filters

The main objective of this thesis was togenerate better filtration technologies for effective production of pure starchproducts, and thereby the optimisation of filtration sequences using created models, as well as the synthesis of the theories of different filtration stages, which were suitable for starches. At first, the structure and the characteristics of the different starch grades are introduced and each starch grade is shown to have special characteristics. These are taken as the basis of the understanding of the differences in the behaviour of the different native starch grades and their modifications in pressure filtration. Next, the pressure filtration process is divided into stages, which are filtration, cake washing, compression dewatering and displacement dewatering. Each stage is considered individually in their own chapters. The order of the different suitable combinations of the process stages are studied, as well as the proper durations and pressures of the stages. The principles of the theory of each stageare reviewed, the methods for monitoring the progress of each stage are presented, and finally, the modelling of them is introduced. The experimental results obtained from the different stages of starch filtration tests are given and the suitability of the theories and models to the starch filtration are shown. Finally, the theories and the models are gathered together and shown, that the analysis of the whole starch pressure filtration process can be performed with the software developed.

High pressure compression of filter cakes

The purpose of this thesis was to investigate the compression of filter cakes at high filtration pressures with five different test materials and to compare the energy consumption of high pressure compression with the energy consumption of thermal drying. The secondary target of this study was to investigate the particle deformation of test materials during filtration and compression. Literature part consists of basic theory of filtration and compression and of the basic parameters that influence the filtration process. There is also a brief description about all of the test materials including their properties and their industrial production and processing. Theoretical equations for calculating the energy consumptions of the filtrations at different conditions are also presented. At the beginning of the experiments at experimental part, the basic filtration tests were done with all the five test materials. Filtration tests were made at eight different pressures, from 6 bars up to 100 bars, by using piston press pressure filter. Filtration tests were then repeated by using a cylinder with smaller slurry volume than in the first series of filtration tests. Separate filtration tests were also done for investigating the deformation of solid particles during filtration and for finding the optimal curve for raising the filtration pressure. Energy consumption differences between high pressure filtration and ideal thermal drying process were done partly experimentally and partly by using theoretical calculation equations. By comparing these two water removal methods, the optimal ranges for their use were found considering their energy efficiency. The results of the measurements shows that the filtration rate increased and the moisture content of the filter cakes decreased as the filtration pressure was increased. Also the porosity of the filter cakes mainly decreased when the filtration pressure was increased. Particle deformation during the filtration was observed only with coal particles.

The influence of crystallization conditions on the filtration characteristics of sulphathiazole suspensions

Cooling crystallization is one of the most important purification and separation techniques in the chemical and pharmaceutical industry. The product of the cooling crystallization process is always a suspension that contains both the mother liquor and the product crystals, and therefore the first process step following crystallization is usually solid-liquid separation. The properties of the produced crystals, such as their size and shape, can be affected by modifying the conditions during the crystallization process. The filtration characteristics of solid/liquid suspensions, on the other hand, are strongly influenced by the particle properties, as well as the properties of the liquid phase. It is thus obvious that the effect of the changes made to the crystallization parameters can also be seen in the course of the filtration process. Although the relationship between crystallization and filtration is widely recognized, the number of publications where these unit operations have been considered in the same context seems to be surprisingly small. This thesis explores the influence of different crystallization parameters in an unseeded batch cooling crystallization process on the external appearance of the product crystals and on the pressure filtration characteristics of the obtained product suspensions. Crystallization experiments are performed by crystallizing sulphathiazole (C9H9N3O2S2), which is a wellknown antibiotic agent, from different mixtures of water and n-propanol in an unseeded batch crystallizer. The different crystallization parameters that are studied are the composition of the solvent, the cooling rate during the crystallization experiments carried out by using a constant cooling rate throughout the whole batch, the cooling profile, as well as the mixing intensity during the batch. The obtained crystals are characterized by using an automated image analyzer and the crystals are separated from the solvent through constant pressure batch filtration experiments. Separation characteristics of the suspensions are described by means of average specific cake resistance and average filter cake porosity, and the compressibilities of the cakes are also determined. The results show that fairly large differences can be observed between the size and shape of the crystals, and it is also shown experimentally that the changes in the crystal size and shape have a direct impact on the pressure filtration characteristics of the crystal suspensions. The experimental results are utilized to create a procedure that can be used for estimating the filtration characteristics of solid-liquid suspensions according to the particle size and shape data obtained by image analysis. Multilinear partial least squares regression (N-PLS) models are created between the filtration parameters and the particle size and shape data, and the results presented in this thesis show that relatively obvious correlations can be detected with the obtained models.

Simulation of the cake formation and growth in cake filtration

A computer model was developed to simulate the cake formation and growth in cake filtration at an individual particle level. The model was shown to be able to generate structural information and quantify the cake thickness, average cake solidosity, filtrate volume, filtrate flowrate for constant pressure filtration or pressure drop across the filter unit for constant rate filtration as a function of filtration time. The effects of particle size distribution and key operational variables such as initial filtration flowrate, maximum pressure drop and initial solidosity were examined based on the simulated results. They are qualitatively comparable to those observed in physical experiments. The need for further development in simulation was also discussed. (c) 2006 Elsevier Ltd. All rights reserved.

Upgrading of fast pyrolysis oils by hot filtration

A hot filtration unit downstream of a 1kg/h fluidised bed fast pyrolysis reactor was designed and built. The filter unit operates at 450oC and consists of 1 exchangeable filter candle with reverse pulse cleaning system. Hot filtration experiments up to 7 hours were performed with beech wood as feedstock. It was possible to produce fast pyrolysis oils with a solid content below 0.01 wt%. The additional residence time of the pyrolysis vapours and secondary vapour cracking on the filter cake caused an increase of non-condensable gases at the expense of organic liquid yield. The oils produced with hot filtration showed superior quality properties regarding viscosity than standard pyrolysis oils. The oils were analysed by rotational viscosimetry and gel permeation chromatography before and after accelerated aging. During filtration the separated particulates accumulate on the candle surface and build up the filter cake. The filter cake leads to an increase in pressure drop between the raw gas and the clean gas side of the filter candle. At a certain pressure drop the filter cake has to be removed by reverse pulse cleaning to regenerate the pressure drop. The experiments showed that successful pressure drop recovery was possible during the initial filtration cycles, thereafter further cycles showed minor pressure drop recovery and therefore a steady increase in differential pressure. Filtration with pre-coating the candle to form an additional layer between the filter candle and cake resulted in total removal of the dust cake.

Natriumsilikaatin liuotuslaitoksen kapasiteetin nosto

Tässä työssä tutkittiin natriumsilikaatin (vesilasi) liuotukseen ja suodatukseen vaikuttavia tekijöitä. Työssä pyrittiin optimoimaan natriumsilikaatin liuotus- ja suodatuskapasiteetti J. M. Huber Finland Oy:n Haminan tehtaan liuotuslaitoksella. Kirjallisuusosassa perehdyttiin kiinteän natriumsilikaatin ja natriumsilikaatin vesiliuoksen ominaisuuksiin, sekä käsiteltiin soveltuvin osin liuotuksen ja suodatuksen teoriaa. Kokeellisessa osassa vertailtiin kahden eri valmistajan natriumsilikaatteja toisiinsa, sekä pyrittiin löytämään molemmille laseille optimaalisimmat prosessiparametrit liuotus- ja suodatuskokeiden avulla. Erilaisia prosessiparametreja ja ajotapoja testattiin tehdasmittakaavan koeajoilla todellisilla prosessilaitteilla. Eri natriumsilikaattien vertailu tehtiin tehdasmittakaavan koeajojen sekä laboratorioanalyysien avulla. Koeajojen tulosten perusteella Taavetista toimitettu vesilasi liukenee nopeammin kuin Puolasta toimitettu ostolasi, mutta puolalaisesta lasista liuotettu silikaatti suodattuu helpommin kuin Taavetin lasista liuotettu silikaatti. Liukenemisnopeuden eroon selitettävissä Taavetin lasin suuremmalla ominaispinta-alalla sekä hauraammalla rakenteella. Suodatuseroon ei löytynyt yksiselitteistä syytä, joten sen löytämiseksi vaadittaisiin jatkotutkimuksia. Kokeiden perusteellaparas keino puolalaisen lasin liuotuksen nopeuttamiseen olisi pitää liuotussäiliön lasiylimäärä mahdollisimman korkeana jokaisessa panoksessa ja nopeuttaa liuotussäiliön panostusta lasin ja veden yhtäaikaisella annostelulla. Tulosten perusteella paras keino Taavetin lasista liuotetun silikaatin suodatuksen helpottamiseen olisi laskea liuoksen tavoitetiheyttä nykyisestä arvostaan, jolloin viskositeetti pienenee merkittävästi ja suodatus onnistuu liuotuslaitoksen kapasiteetin kannalta paremmin. Edellä mainituilla ajotavoilla tehtyjen koeajojen perusteella, molemmilla laseilla on mahdollista päästä 150 MT/d tavoitekapasiteettiin, mutta varmin tapa kyseisen kapasiteetin saavuttamiseksi olisi lisätä suodatuskapasiteettia investoimalla toiseen silikaattisuodattimeen.

Pigmenttien suodatus

Työn tavoitteena oli tutkia neljän eri koesuotimen soveltuvuutta pigmenttilietteen kiintoainepitoisuuden nostoon. Työssä käytetyt suotimet olivat Larox PF 0,1, Certus-CU-0047, Crossflow-koesuodin ja Steuerung ET06-linko. Suodinväliaineena Larox PF 0,1-suotimessa ja Crossflow-koesuotimessa käytettiin Tamfelt Oyj:n suodinkankaita. Certus-CU-0047-suotimessa suodinväliaineena toimi keraaminen membraani. Työn kirjallisuusosassa tarkasteltiin partikkelien karakterisointia, suodatuksen teoriaa, kakkusuodatusta, suodinväliaineista suodinkankaita ja membraaneja. Lisäksi tarkasteltiin paperin päällystämiseen käytettyjen pigmenttien ominaisuuksia ja niiden suodatusta. Kokeet suoritettiin Larox PF 0,1, Certus-CU-0047 ja Crossflow-koesuotimella vakiopainesuodatuksena yhdellä paineella. Steuerung ET06-lingon kokeet suoritettiin vakiovirtaussuodatuksena käyttäen kolmea eri virtausnopeutta ja kolmea eri lingon ja ruuvin kierrossuhdetta. Työssä suodatettiin neljää erilaista pigmenttilietettä. Suodoksista otettiin näytteitä niiden sameuden määrittämiseksi. Larox Pf 0,1-suotimella ja Steuerung ET06-dekantterilingolla saatiin nostettua pigmenttilietteen kiintoainepitoisuutta erittäin hyvin. Loput kaksi suodinta eivät sovellu tähän tarkoitukseen ollenkaan. Vakiopainesuodatuksissa suodatusajat muodostuivat kuitenkin liian pitkiksi. Suodoksien kiintoainepitoisuudet olivat suurimmaksi osaltaan pieniä lukuun ottamatta tiettyjä suodinkankaita. Lietteen 2 kiintoainepitoisuuden nostaminen oli kaikilla suotimilla erittäin vaikeaa, muut lietteet suodattuivat kohtuullisen hyvin. Näiden kokeiden perusteella voidaan sanoa, että varsinkin vakiovirtaussuodatus soveltuu hyvin ainakin tiettyjen pigmenttilietteiden kiintoainepitoisuuden nostoon.

Kakun rakenteen vaikutus pesutulokseen

Tässä työssä tutkittiin suodatukseen vaikuttavien tekijöiden vaikutusta suodatuksessa syntyvän kakun ominaisuuksiin sekä kakun ominaisuuksien vaikutusta syrjäytyspesun tehokkuuteen. Lisäksi määritettiin tärkeimmät suodatusparametrit sekä niiden riippuvuudet suodatusolosuhteista. Toissijaisena tavoitteena oli lisäksi tutkia, miten suodatusolosuhteita ja suodatettavan lietteen ominaisuuksia muuttamalla voidaan vaikuttaa suodatusjakson kestoon. Työn kirjallisuusosassa käsiteltiin aluksi yleisesti kiintoaineen erotusta nesteestä. Tämän jälkeen käsiteltiin yleisimmät suodatustekniikat ja tarkasteltiin yksityiskohtaisemmin painesuodatusta ja varsinkin syntyvän kakun rakenteeseen vaikuttavia tekijöitä. Lopuksi käytiin läpi kakulle suodatuksen jälkeen suoritettavat jälkikäsittelymenetelmät ja selvitettiin varsinkin syrjäytyspesun tehokkuuteen vaikuttavia tekijöitä tarkemmin. Kokeellisessa osassa tehtiin koesuodatuksia lietteellä joka sisälsi hienojakoista pigmenttiä. Koesuodatukset tehtiin kahdella eri kankaalla panostoimisella piston press- laboratoriopainesuodattimella johon oli liitetty tiedonkeruuohjelmisto, joka keräsi tiedostoon paineet suodatuskammiossa, kankaan alapuolella ja työsylinterin syöttölinjassa sekä lisäksi männän korkeuden, lietteen lämpötilan ja suodosvaakalukeman. Lietteiden ominaisuuksia seurattiin analysoimalla niiden kiintoainepitoisuuksia, kloridipitoisuuksia, z-potentiaaleja ja partikkelikokojakau-mia siten että jokaisessa suodatuksessa käytetyn lietteen ominaisuudet olivat tiedossa. Suodatusten jälkeen syntyneistä kakuista määritettiin kiintoaine- sekä joissain tapauksissa myös kloridipitoisuudet. Suodatus- ja puristuspaineiden havaittiin vaikuttavan kakkujen huokoisuuksiin ja ominaisvastuksiin selvästi, joskin muutokset olivat melko pieniä. Vaikutus näkyi selvästi myös suodatusten kestoissa ja muutosten havaittiin olevan merkittävän suuruisia. Myös lietteen pH:n havaittiin vaikuttavan merkitsevästi suodatusten kestoihin ja kakkujen ominaisuuksiin. Pesutuloksen ja kakun ominaisuuksien välille löydettiin riippuvuus heikoksi jääneestä pesutuloksesta huolimatta. Myös koesuodatuksissa käytettyjen kankaiden välillä havaittiin selviä eroavaisuuksia.

Uuttoprosessin suunnittelu

Teknologian kehitys ja prosessien tiukempi valvonta ovat alentaneet selluteollisuuden häviöitä tehden prosesseista suljetumpia. Valitettavasti nämä edistysaskeleet teknologiassa ovat lisänneet prosessiin kuulumattomien yhdisteiden määrää kemikaalien talteenottokierrossa. Näistä kemikaaleista haitallisimpia ovat kloridi- ja kaliumyhdisteet, jotka tulevat prosessiin raaka-aineiden ja prosessikemikaalien mukana. Kloridi ja kalium muodostavat emäksisissä liuoksissa epäorgaanisia liukoisia yhdisteitä, jotka rikastuvat lipeäkiertoon. Soodakattilassa kloridien läsnäolo alentaa tuhkan sulamislämpötilaa sekä tarttumispistettä, lisää korroosiota ja saostumien muodostumista kattilan pinnalle. Nämä seuraukset voivat vähentää vuosituotantoa ja nostaa korjauskustannuksia. Kaliumin ja kloridin rikastumista talteenottokiertoon voidaan estää poistamalla ne prosessista. Prosessiin kuulumattomat yhdisteet tulisi poistaa talteenottoprosessista ja säilyttää samalla korkea kemikaalien talteenottoprosentti. Koska kaliumin ja kloridin rikastumiskertoimet soodakattilan tuhkassa ovat korkeita, on tuhkan käsittely tehokasta. Kloridin ja kaliumin poistoon on kehitetty menetelmiä, joilla voidaan vähentää hyödyllisten kemikaalien häviöitä. Näitä menetelmiä ovat uutto, ioninvaihto, elektrodialyysi, jäähdytyskiteytys ja haihdutuskiteytys. Menetelmissä tuhka jaetaan kloridi- ja kaliumpitoiseen osaan ja natriumsulfaattipitoiseen osaan. Kloridi ja kalium poistetaan prosessista ja loput palautetaan lipeäkiertoon. Kloridin ja kaliumin poistoa tuhkasta tutkittiin uuttamalla tuhkaa vedellä. Parhaissa käyttöolosuhteissa natriumsulfaatin liukoisuus veteen on huomattavasti alhaisempi kuin kaliumkloridin liukoisuus veteen. Optimaalinen uuttolämpötila ja tuhka-vesisuhde määritettiin siten, että kloridi- ja kaliumpitoisuudet suodoksessa olivat mahdollisimman korkeat sekä natriumin ja muiden anioneiden pitoisuudet suodoksessa mahdollisimman alhaiset. Saatuja tuloksia käytettiin jatkuvatoimisen uuttoprosessin suunnittelussa.

Höyryn käyttö suodinkakun pesussa ja kuivauksessa

Työssä käsitellään suodinkakkujen kuivapitoisuuksien muuttumista, kun kuivauksessa käytetään paineilman sijasta kylläistä höyryä.

Suodattimessa tapahtuvan kiintoaineen laskeutumisen vaikutus suodinkakun ominaisuuksiin

Laskeutus ja suodatus ovat paljon tutkittuja ja laajassa käytössä olevia mekaanisia erotusmenetelmiä. Laskeutumisen vaikutusta suodatuksen yhteydessä ei kuitenkaan ole tutkittu juurikaan. Tämän työn tavoitteena on selvittää suodattimessa ennen vakiopaine suodatusta tapahtuvan kiintoaineen laskeutumisen vaikutusta suodatuksen tuloksiin. Työn kirjallisuusosuudessa käsitellään työhön liittyvää teoriaa partikkelikokojakaumista, laskeutumisesta, suodatuksesta ja flokkulanttien käytöstä sekä tehdään yhteenvetoa aiemmasta laskeutumista ja suodatusta yhdistävästä tutkimuksesta. Koska käsitellyt aiheet ovat laajoja ja niitä on useita, joudutaan teorian esittämisessä tekemään rajauksia. Työn kokeellisessa osassa tutkitaan suodattimessa tapahtuvan laskeutuksen vaikutusta suodatukseen. Kokeet suoritetaan 20 m-% kalsiumkarbonaattilietteellä. Kokeissa tutkitaan laskeutumisen vaikutusta antamalla lietteen laskeutua suodattimessa tietyn ajan ennen suodatuksen aloitusta. Lisäksi tutkitaan flokkulanttien lisäämisen vaikutusta mahdollisiin ilmiöihin. Koetuloksista nähdään pidemmän laskeutusajan ennen suodatusta alentavan kakun keskimääräistä ominaisvastusta ja vaikutus kasvaa merkittävästi kun lietteeseen on lisätty flokkulanttia. Suodatusta edeltävä laskeutus siis helpottaa varsinaista suodatusta.

Jauhatusparametrien vaikutus jauhatustuotteen partikkelikokoon ja suodattuvuuteen

Tämän diplomityön tarkoituksena on tutkia ensin jauhatusparametrien vaikutus rikastushiekan hienousasteeseen eli miten partikkelikokojakaumaa kuvaavat partikkelikoot muuttuvat. Tämän jälkeen tutkitaan miten rikastushiekan hienousasteen muuttuminen vaikuttaa jauhettujen rikastushiekkalietenäytteiden suodattuvuuteen. Partikkelikokojakauman variaatioista yritetään löytää yhteys suodinkakun ominaisvastuksen ja huokoisuuden välillä. Jauhatus suoritettiin laboratoriomittakaavan helmimyllyllä märkäjauhatuksena. Jauhatusta varten tehtiin kolmitasoinen faktorikoesuunnitelma, jossa muuttujina ovat lasihelmien halkaisija, jauhatusaika ja sekoitinelimen pyörimisnopeus. Suodatus toteutettiin vakiopainesuodatuksena kolmella eri suodatuspaineella Nutsche-suodattimella. Työn tuloksista saatiin selville, että partikkelikokojakauman leveys korreloi suodinkakun ominaisvastuksen kanssa. Kun partikkelikokojakauma leveys muuttui kapeammaksi, saatiin kakun ominaisvastus pienemmäksi ja suodatukseen kulunut aika lyheni. Kapein partikkelikokojakauman leveys saatiin suurimmalla helmen halkaisijalla, pisimmällä jauhatusajalla sekä suurimmalla sekoitusnopeudella.

Remoção conjugada de metais e óleo de água produzida

Petroleum can be associated or not with natural gas, but in both cases water is always present in its formation. The presence of water causes several problems, such as the difficulty of removing the petroleum from the reservoir rock and the formation of waterin-oil and oil-in-water emulsions. The produced water causes environmental problems, which should be solved to reduce the effect of petroleum industry in the environment. The main objective of this work is to remove simultaneously from the produced water the dispersed petroleum and dissolved metals. The process is made possible through the use of anionic surfactants that with its hydrophilic heads interacts with ionized metals and with its lipophilic tails interacts with the oil. The studied metals were: calcium, magnesium, barium, and cadmium. The surfactants used in this research were derived from: soy oil, sunflower oil, coconut oil, and a soap obtained from a mixture of 5wt.% coconut oil and 95wt.% animal fat. It was used a sample of produced water from Terminal de São Sebastião, São Paulo. As the concentration of the studied metals in produced water presented values close to 300 mg/L, it was decided to use this concentration as reference for the development of this research. Molecular absorption and atomic absorption spectroscopy were used to determine petroleum and metals concentrations in the water sample, respectively. A constant pressure filtration system was used to promote the separation of solid and liquid phases. To represent the behavior of the studied systems it was developed an equilibrium model and a mathematical one. The obtained results showed that all used surfactants presented similar behavior with relation to metals extraction, being selected the surfactant derived from soy oil for this purpose. The values of the partition coefficients between the solid and liquid phases " D " for the studied metals varied from 0.2 to 1.1, while the coefficients for equilibrium model " K " varied from 0.0002 and 0.0009. The removal percentile for oil with all metals associated was near 100%, showing the efficiency of the process