Síntese e caracterização de copolímeros à base de poli(metacrilato de metila) e divinilbenzeno com propriedades magnéticas

Nesta dissertação, foram sintetizados copolímeros à base de poli(metacrilato de metila) (PMMA), divinilbenzeno (DVB) com propriedades magnéticas pela técnica de polimerização em suspensão. O material utilizado para conferir propriedade magnética foi o ferro. Foi estudada a influência das variáveis reacionais para a formação de microesferas (ordem de adição das fases orgânica e aquosa e a dispersão do ferro antes e após a pré-polimerização), o efeito da concentração de ferro adicionado na polimerização, a influência da razão molar MMA/DVB na formação do copolímero, o efeito do tipo de agente de suspensão e a velocidade de agitação para a síntese dos copolímeros. Os copolímeros foram caracterizados quanto à morfologia, estabilidade térmica, teor de ferro incorporado, distribuição de tamanho de partículas, propriedades magnéticas, área superficial, volume e tamanho de poros. As análises de propriedades magnéticas mostraram que os materiais obtidos não apresentaram ciclos de histerese, estando assim próximos de um material com propriedades superparamagnéticas, com magnetização de saturação entre 8,0 e 13,0 emu/g. Os copolímeros sintetizados com velocidade de agitação 500 RPM, temperaturade 90 C, tempo de polimerização de 24h, monômeros MMA/DVB 50/50 (% molar); razão volumétrica fase orgânica/fase aquosa 1/3, diluente heptano, grau de diluição 100% apresentaram melhor controle morfológico, melhor magnetização de saturação, tamanho de partículas menores e maior tamanho de poros

Modificação química de amostras de poli(metacrilato de metila) comerciais com aminas funcionalizadas assistidas por micro-ondas

Este trabalho avaliou a reação de amidação sob catálise de DBU/NaCN de amostras comerciais de poli(metacrilato de metila), (PMMA), massa molar 60.000 u.m.a. com as aminas, alilamina, 2-morfolilaminoetano, 1-(3-aminopropil)-imidazol e N,N-dimetil-trimetilenodiamina com ativação por reator de micro-ondas. O estudo com alilamina e 2-morfolilaminoetano se mostrou eficaz, apresentando percentuais de derivatização significativos (27% e 37% , respectivamente). A quantidade de material polimérico obtido na purificação foi de cerca de 36 % para as duas aminas. O estudo evidenciou a importância dos catalisadores DBU/NaCN, pois sem eles a reação não ocorre e quando utilizados isoladamente, o grau de incorporação é muito menor. Já o estudo com as aminas 1-(3-aminopropil)-imidazol e N,N-dimetil-trimetilenodiamina mostrou-se ineficaz devido à dificuldade de purificação dos produtos. Tentativas de purificação por precipitação com metanol e soluções hidrometanólicas de diferentes concentrações mostraram-se ineficazes. Os novos PMMA modificados foram caracterizados por FT-IR, RMN-1H e análise elementar. Foram observadas alterações na taticidade do PMMA em reações ativadas por micro-ondas

Amidação de Poli( metacrilato de metila)

Nesta dissertação foram avaliadas metodologias para reação de amidação de amostras comerciais de poli (metilmetacrilato), PMMA, com alilamina e benzilamina. A reação foi executada em tubo selado sob aquecimento a 90 C por sete dias, sem que nenhuma quantidade mensurável de amida pudesse ser detectada por FTIR e RMN. A reação foi reavaliada sob catalise de DBU, 3,4% molar, sem que nenhum resultado positivo obtido. O emprego de DBU associado ao NaCN como co-catalisador mostrou-se eficaz é o PMMA pode ser derivatizado em 30 %, com alilamina, e 13 % com benzilamina, sob as mesmas condições de temperatura e tempo. A analise elementar e o RMN-1H foram conclusivos na quantificação das reações enquanto o FTIR mostrou-se pouco eficaz devido a sobreposições de bandas. A taticidade das amostras comerciais de PMMA e do material produzido pode ser avaliada por RMN. Experimentos exploratórios efetuados em forno de microondas monomodo sob as mesmas relações molares com aquecimento a 120 C por 30 minutos com 80 W de potencia não foram capazes de promover alterações na matriz polimérica

Desevolvimento de nanocompósitos de poli(metacrilato de metila)/argila processados por mistura no estado fundido

Poly(methyl methacrylate)/clay nanocomposites were prepared by melt mixing using a montmorillonite-rich clay (MMT). The clay in natura was treated with acrylic acid to facilitate the dispersion in the polymer matrix. A masterbatch of PMMA/clay was prepared and combined with the pure PMMA and then subjected to extrusion process using singlescrew and twin-screw extruders followed by injection. Nanocomposites were processed with clay contents of 1, 3, 5 and 8 wt.%. The effect of shear processing on the morphology of the nanocomposites was evaluated by XRD, SEM and TEM. Thermal and mechanical properties of the nanocomposites were investigated through TGA, DSC, HDT, VICAT, tensile and impact tests, to evaluate the effect of the addition of clay to the PMMA matrix. Flammability tests were also conducted to investigate the effect of the addition of clay on the flame retardation properties. SEM images of the nanocomposites indicated the presence of clay agglomerates, which resulted in the reduction of properties such as thermal stability, mechanical strength and impact resistance, and increased the rate of burning for materials processed by both extrusion routes

Estudo morfológico da blenda polimérica poli(metacrilato de metila)/poli(tereftalato de etileno) reciclado (PMMA/PET)

Among the options for plastics modification more convenient, both from a technical-scientific and economic, is the development of polymer blends by processing in the molten state. This work was divide into two stages, with the aim to study the phase morphology of binary blend PMMA / PET blend and this compatibilized by the addition of the poly(methyl methacrylate-co-glycidyl methacrylate-co-ethyl acrylate) copolymer (MMA-GMA-EA). In the first stage is analyzed the morphology of the blend at a preliminary stage where we used the bottle-grade PET in a Haake torque rheometer and the effect of compatibilizer in this blend was evaluated. In the second stage the blend was processed using the recycled PET in a single screw extruder and subsequently injection molding in the shape of specimens for mechanical tests. In both stages we used a transmission electron microscopy (TEM) to observe the morphologies of the samples and an image analyzer to characterize them. In the second stage, as well as analysis by TEM, tensile test, scanning electron microscopy (SEM) and atomic force microscopy (AFM) was performed to correlate the morphology with the mechanical properties. The samples used in morphological analyzes were sliced by cryo-ultramicrotomy technique for the analysis by TEM and the analysis by SEM and AFM, we used the flat face of the block after cut cryogenic. It was found that the size of the dispersed phase decreased with the addition of MMA-GMA-EA in blends prepared in a Haake. In the tensile test, the values of maximum tensile strength and modulus of elasticity is maintained in a range between the value of pure PMMA the pure PET, while the elongation at break was influenced by the composition by weight of the PMMA mixture. The coupling agent corroborated the results presented in the blend PMMA / PETrec / MMA-GMA-EA (80/15/5 %w/w), obtained by TEM, AFM and SEM. It was concluded that the techniques used had a good morphologic correlation, and can be confirmed for final analysis of the morphological characteristics of the blends PMMA / PET

Efeito da adição dos azocorantes DR73 e DB79 nas propriedades do poli(metacrilato de metila)

Currently new polymeric materials have been developed to replace other of traditionally materials classes. The use of dyes allows to expand and to diversify the applications in the polymeric materials development. In this work the behavior and ability of azo dyes Disperse Blue 79 (DB79) and Disperse Red 73 (DR73) on poly(methyl methacrylate) (PMMA) were studied. Two types of mixtures were used in the production of masterbatches: 1) rheometer 2) solution. Processing by extrusion-blow molding of PMMA was carried out in order to evaluate the applications of polymeric films. Thermal analysis were performed by thermogravimetry to evaluate polymer and azo dyes thermal stability. Colorimetric analysis were obtained through monitoring the spectral variations associated with sys/trans/anti azo dyes isomerization process Colorimetric data were treated and evaluated in accordance to the color system RGB and CIEL*ab, by monitoring the color change as function of time. Mechanical properties, characterized by tensile tests, were evaluated and correlated with the presence and content of azo dyes in the samples. Analyses by scanning electronic microscopy (SEM) were performed on the surfaces of samples to check the azo dye dispersion after the mixing process. It was concluded that the production of PMMA/azo dyes is possible and feasible, and the mixtures produced had synergy of properties for use in various applications

Processamento e caracterização de compósitos Poli(METACRILATO DE METILA)/Sílica (PMMA/SiO2)

Currently the search for new materials with properties suitable for specific applications has increased the number of researches that aim to address market needs. The poly (methyl methacrylate) (PMMA) is one of the most important polymers of the family of polyacrylates and polymethacrylates, especially for its unique optical properties and weathering resistance, and exceptional hardness and gloss. The development of polymer composites by the addition of inorganic fillers to the PMMA matrix increases the potential use of this polymer in various fields of application. The most commonly used inorganic fillers are particles of silica (SiO2), modified clays, graphite and carbon nanotubes. The main objective of this work is the development of PMMA/SiO2 composites at different concentrations of SiO2, for new applications as engineering plastics. The composites were produced by extrusion of tubular film, and obtained via solution for application to commercial PMMA plates, and also by injection molding, for improved the abrasion and scratch resistance of PMMA without compromising transparency. The effects of the addition of silica particles in the polymer matrix properties were evaluated by the maximum tensile strength, hardness, abrasion and scratch resistance, in addition to preliminary characterization by torque rheometry and melt flow rate. The results indicated that it is possible to use silica particles in a PMMA matrix, and a higher silica concentration produced an increase of the abrasion and scratch resistance, hardness, and reduced tensile strength

Influência de tratamentos térmicos no comportamento mecânico da blenda poli(metacrilato de metila) / poli(tereftalato de etileno) reciclado

Studies indicate that a variation in the degree of crystallinity of the components of a polymer blend influences the mechanical properties. This variation can be obtained by subjecting the blend to heat treatments that lead to changes in the spherulitic structure. The aim of this work is to analyze the influence of different heat treatments on the variation of the degree of crystallinity and to establish a relationship between this variation and the mechanical behavior of poly(methyl methacrylate)/poly(ethylene terephthalate) recycled (PMMA / PETrec) with and without the use of compatibilizer agent poly(methyl methacrylate-al-glycidyl methacrylate-al-ethyl acrylate) (MMAGMA- EA). All compositions were subjected to two heat treatments. T1 heat treatment the samples were treated at 130 ° C for 30 minutes and cooled in air. In T2, the samples were treated at 230 ° C for 5 minutes and cooled to approximately -10 ° C. The variation of the degree of crystallinity was determined by the proportional relationship between crystallinity and density, with the density measured by pycnometry. The mechanical behavior was verified by tensile tests with and without the presence of notches and pre-cracks, and by method of fracture toughness in plane strain (KIC). We used the scanning electron microscopy (SEM) to analyze the fracture surface of the samples. The compositions subjected to heat treatment T1, in general, showed an increase in the degree of crystallinity in tensile strength and a tendency to decrease in toughness, while compositions undergoing treatment T2 showed that the opposite behavior. Therefore, this work showed that heat treatment can give a polymer blend further diversity of its properties, this being caused by changes in the crystal structure

Processamento e caracterização da blenda poli (metacrilato de metila) (PMMA) elastomerico e poli (tereftalato de etileno) (PET) pós-consumo

This work studied the immiscible blend of elastomeric poly(methyl methacrylate) (PMMA) with poly(ethylene terephthalate) (PET) bottle grade with and without the use of compatibilizer agent, poly(methyl methacrylate-co-glycidyl methacrylate - co-ethyl acrylate) (MGE). The characterizations of torque rheometry, melt flow index measurement (MFI), measuring the density and the degree of cristallinity by pycnometry, tensile testing, method of work essential fracture (EWF), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were performed in pure polymer and blends PMMA/PET. The rheological results showed evidence of signs of chemical reaction between the epoxy group MGE with the end groups of the PET chains and also to the elastomeric phase of PMMA. The increase in the concentration of PET reduced torque and adding MGE increased the torque of the blend of PMMA/PET. The results of the MFI also show that elastomeric PMMA showed lower flow and thus higher viscosity than PET. In the results of picnometry observed that increasing the percentage of PET resulted in an increase in density and degree crystallinity of the blends PMMA/PET. The tensile test showed that increasing the percentage of PET resulted in an increase in ultimate strength and elastic modulus and decrease in elongation at break. However, in the phase inversion, where the blend showed evidence of a co-continuous morphology and also, with 30% PET dispersed phase and compatibilized with 5% MGE, there were significant results elongation at break compared to elastomeric PMMA. The applicability of the method of essential work of fracture was shown to be possible for most formulations. And it was observed that with increasing elastomeric PMMA in the formulations of the blends there was an improvement in specific amounts of essential work of fracture (We) and a decrease in the values of specific non-essential work of fracture (βWp)

Efeito de argilas organofílicas na estrutura e propriedades de nanocompósitos de poli(metacrilato de metila)

Nacomposites of polymers and lamellar clayminerals, has generated high scientific and technological interest, for having mechanical properties and gas barriers differentiated of polymers and conventional composites. In this work, it was developed nanocomposites by single screw extruder and injection, utilizing commercial raw material, with the goal to investigate the quality of new developed materials. It was evaluated the influence of the content and the kind of clay in the structure and in the nanocomposites properties. It was used regular and elastomeric poly (methyl methacrylate) (Acrigel LEP 100 and Acrigel ECP800) and six montmorillonites (Cloisite 10A, 11B, 15A, 20A, 25A e 30B) at the concentration of 1% e 3% in weight. The nanocomposites were characterized by X-ray diffraction (XRD), thermal gravimetric analysis (TGA), transmission electron microscopy (TEM), colorimetric, optical transparency, flexural and tensile tests, Rockwell hardness and esclerometry. It was founded that is possible to obtain intercalated and exfoliated nanocomposites PMMA/MMT, and the top results was obtained in the materials with 1%in clay weight organophilizated with 2M2HT (Cloisite 15A and 20A) presented intercalate and hybrid morphology (exfoliated and flocullated). The ones that was produced with organophilizated clay with 2MHTL8 (Cloisite 30B) had excellent visual quality, but the majority presented hybrid morphology. In the materials processed with organophilizated clay with MT2ETOH (Cloisite 30B), there were color change and loss of transparency. It occurs improvement in a few mechanical properties, mainly in the materials produced with PMMA elastomeric (Acrigel ECP800), being more significant, the increase in the resistance to stripping in those nanocomposites

Estudos preliminares da preparação de fibras ópticas plásticas e híbridos orgânicos-inorgânicos luminescentes a partir de poli(metacrilato de metila) comercial

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Propriedades físicas do Poliestireno e do Poli (metacrilato de metila) modificados com Óleo de Buriti (mauritia flexuosa)

Nos dias atuais, cresce cada vez mais o uso de polímeros no nosso cotidiano. Esse crescimento deve-se essencialmente à sua aplicabilidade com grande eficácia na substituição de materiais clássicos como madeira, metais, vidros e até mesmo papel. Além disso, propriedades especiais de polímeros, como condutividade elétrica, fotoluminescência e difusividade térmica, tem sido objeto de interesse da comunidade cientifica básica e aplicada. Algumas dessas propriedades podem, dependendo da necessidade a qual se destina ser modificadas a partir da inserção de outras substancias em suas matrizes. O interesse cientifico por óleos vegetais vem se tornando cada vez mais frequente, um desses óleos conhecido como Óleo de Buriti (mauritia flexuosa), tem em sua composição um alto teor de acido oleico e pró-vitamina A (conhecida como β-caroteno), tais substancias apresentam propriedades interessantes que já foram reportadas por vários pesquisadores em periódicos científicos. Apresentamos nessa dissertação o estudo de algumas propriedades físicas de amostras de dois polímeros comerciais de uso rotineiro: Poliestireno (OS) e Poli (metacrilato de metila) (PMAM) que foram dopadas com Óleo de Buriti (OB) em diferentes concentrações, a saber, 8.08%, 14.96%, 34.55% e 46.81%. outras concentrações de óleo foram tentadas, mas sem êxito, pois o óleo não conseguiu se fixar na matriz polimérica. Observamos que as amostras incorporaram de forma intersticial o óleo, alterando sua transparência natural e incorporando uma coloração de cor variável entre o amarelo claro ao alaranjado, dependendo da concentração. A partir de medidas ópticas percebemos que os polímeros passaram a apresentar propriedades semelhantes as do óleo como o fenômeno de emissão a partir da excitação por ultravioleta, confirmando assim a sua presença no interior dos plásticos. Caracterizamos os compósitos também através da constante dielétrica e difusividade térmica em função da temperatura. Essas medidas revelaram o comportamento do sistema formado pelo óleo + polímero e identificamos a mudança de estado físico (líquido ↔ sólido) sofrida pelas micro-gotas de óleo dentro da matriz.

Organofilização de uma Mg-bentonita da bacia do Parnaíba-Sul do Maranhão e sua utilização em poli (metacrilato de metila)

Bentonitas são argilas que tem como seu principal constituinte argilominerais do grupo da esmectita, predominantemente montmorillonita. De acordo com o cátion predominante no espaço intercamada da esmectita, a bentonita pode ser classificada como sódica, cálcica ou magnesiana. Essas argilas possuem vasta aplicação industrial, como fluidos de perfuração, pelotização, moldes de fundição, dentre outros. Para algumas aplicações mais específicas e que agregam maior valor ao produto final, como na síntese de nanocompósitos polímero/argila, faz-se necessário à intercalação de íons orgânicos na intercamada do argilomineral. No Brasil, a produção industrial de argilas organofílicas é pequena e voltada para os mercados de tintas, graxas e resinas de poliéster. Empresas do setor de bentonitas, que ainda não estão produzindo esse tipo de material, vêm mostrando crescente interesse nesta aplicação. Dentro desse contexto, este trabalho buscou avaliar o potencial da Bentonita Formosa, uma Mg-bentonita recentemente descrita e relativamente abundante no nordeste do Brasil, na produção de argilas organofílicas e sua aplicação em síntese de nanocompósitos polímero/argila. Para isso, foram realizadas sínteses variando a concentração dos íons surfactantes hexadeciltrimetilamônio (HDTMA⁺) e dodeciltrimetilamônio (DTMA⁺) em 0,7, 1,0 e 1,5 vezes o valor de CEC, com tempo de reação de 12 horas e variação de temperatura de 25 ºC e 80 ºC. A Mg-Bentonita in natura e ativada com carbonato de sódio foi utilizada como material de partida. Tanto o material de partida como as argilas organofílicas obtidas foram caracterizadas por DRX, DTA/TG e IV. As argilas que apresentaram melhores resultados de intercalação foram utilizadas nas proporções de 1%, 3% e 10% para a síntese de nanocompósitos poli(metacrilato de metila) (PMMA)/argila. As análises de DRX confirmaram a intercalação dos íons orgânicos no espaço intercamada da Mg-esmectita com e sem ativação. Com os resultados de IV foi possível observar que a razão de confôrmeros gauche/trans diminui com o aumento do espaçamento basal. Os resultados de DTA/TG confirmaram a estabilidade térmica das argilas organofílicas à temperatura máxima de 200 °C, o que possibilita a utilização desse material em síntese de nanocompósitos polímero/argila obtidos por processo de fusão. A análise de DRX confirmou a intercalação do PMMA no espaço intercamada da Mg-esmectita em todos os nanocompósitos produzidos. Com as análises de DSC foi possível observar o aumento da temperatura de transição vítrea para todos os nanocompósitos, quando comparados com PMMA puro. Com isso, é possível concluir que a Mg-Bentonita pode ser intercalada com íons alquilamônio, sem a necessidade prévia de ativação sódica, formando argilas organofílicas, assim como sua utilização em síntese de nanocompósitos. Essa possibilidade de utilização da Mg-bentonita in natura pode representar uma importante diferença em termos de custos de processo, na comparação com as bentonitas cálcicas existentes no Brasil, ou mesmo as importadas, que precisam ser ativadas durante o beneficiamento. Finalmente, acredita-se que a pesquisa deve avançar com a avaliação das propriedades mecânicas dos nanocompósitos produzidos neste trabalho, visando as diferentes possibilidades de aplicações desses materiais.

Desevolvimento de nanocompósitos de poli(metacrilato de metila)/argila processados por mistura no estado fundido

Poly(methyl methacrylate)/clay nanocomposites were prepared by melt mixing using a montmorillonite-rich clay (MMT). The clay in natura was treated with acrylic acid to facilitate the dispersion in the polymer matrix. A masterbatch of PMMA/clay was prepared and combined with the pure PMMA and then subjected to extrusion process using singlescrew and twin-screw extruders followed by injection. Nanocomposites were processed with clay contents of 1, 3, 5 and 8 wt.%. The effect of shear processing on the morphology of the nanocomposites was evaluated by XRD, SEM and TEM. Thermal and mechanical properties of the nanocomposites were investigated through TGA, DSC, HDT, VICAT, tensile and impact tests, to evaluate the effect of the addition of clay to the PMMA matrix. Flammability tests were also conducted to investigate the effect of the addition of clay on the flame retardation properties. SEM images of the nanocomposites indicated the presence of clay agglomerates, which resulted in the reduction of properties such as thermal stability, mechanical strength and impact resistance, and increased the rate of burning for materials processed by both extrusion routes

Estudo morfológico da blenda polimérica poli(metacrilato de metila)/poli(tereftalato de etileno) reciclado (PMMA/PET)

Among the options for plastics modification more convenient, both from a technical-scientific and economic, is the development of polymer blends by processing in the molten state. This work was divide into two stages, with the aim to study the phase morphology of binary blend PMMA / PET blend and this compatibilized by the addition of the poly(methyl methacrylate-co-glycidyl methacrylate-co-ethyl acrylate) copolymer (MMA-GMA-EA). In the first stage is analyzed the morphology of the blend at a preliminary stage where we used the bottle-grade PET in a Haake torque rheometer and the effect of compatibilizer in this blend was evaluated. In the second stage the blend was processed using the recycled PET in a single screw extruder and subsequently injection molding in the shape of specimens for mechanical tests. In both stages we used a transmission electron microscopy (TEM) to observe the morphologies of the samples and an image analyzer to characterize them. In the second stage, as well as analysis by TEM, tensile test, scanning electron microscopy (SEM) and atomic force microscopy (AFM) was performed to correlate the morphology with the mechanical properties. The samples used in morphological analyzes were sliced by cryo-ultramicrotomy technique for the analysis by TEM and the analysis by SEM and AFM, we used the flat face of the block after cut cryogenic. It was found that the size of the dispersed phase decreased with the addition of MMA-GMA-EA in blends prepared in a Haake. In the tensile test, the values of maximum tensile strength and modulus of elasticity is maintained in a range between the value of pure PMMA the pure PET, while the elongation at break was influenced by the composition by weight of the PMMA mixture. The coupling agent corroborated the results presented in the blend PMMA / PETrec / MMA-GMA-EA (80/15/5 %w/w), obtained by TEM, AFM and SEM. It was concluded that the techniques used had a good morphologic correlation, and can be confirmed for final analysis of the morphological characteristics of the blends PMMA / PET