On tuning the orientation of grains of spray pyrolysed ZnO thin films

Effect of varying spray rate on the structure and optoelectronic properties of spray pyrolysed ZnO film is analysed. ZnO films were characterised using different techniques such as X-ray diffraction (XRD), photoluminescence, electrical resistivity measurement, and optical absorption. The XRD analysis proved that, with the increase in spray rate, orientation of the grains changed from (1 0 1) plane to (0 0 2) plane. The films exhibited luminescence in two regions—one was the ‘near band-edge’ (NBE) (∼380 nm) emission and the other one was the ‘blue-green emission’ (∼503 nm). Intensity of the blue-green emission decreased after orientation of grains shifted to (0 0 2) plane. Scanning electron microscope (SEM) analysis of the films asserts that spray rate has major role in improving the crystallographic properties of the films. Moreover resistivity of the films could be lowered to 2.4×10−2 cm without any doping or post-deposition annealing

Epitaxial growth of biferroic YMnO3(0001) on platinum electrodes

Epitaxial films of the biferroic YMnO3 (YMO) oxide have been grown on platinum-coated SrTiO3(1 1 1) and Al2O3(0 0 0 1) substrates. The platinum electrodes, (1 1 1) oriented, are templates for the epitaxy of the hexagonal phase of YMO with a (0 0 0 1) out-of-plane orientation, which is of interest as this is the polarization direction of YMO. X-ray diffractometry indicates the presence of two crystal domains, 60° rotated in-plane, in the Pt(1 1 1) layers which subsequently are transferred on the upperlaying YMO. Cross-section analysis by high-resolution transmission electron microscopy (HRTEM) of YMnO3/Pt/SrTiO3(1 1 1) shows high-quality epitaxy and sharp interfaces across the structure in the observed region. We present a detailed study of the epitaxial growth of the hexagonal YMO on the electrodes.

Reduced microwave losses of YBa2Cu3O7_thin films on electro-optic LiNbO3 crystals

We report on the growth of epitaxial YBa2Cu3O7 thin films on X-cut LiNbO3 single crystals. The use of double CeO2/YSZ buffer layers allows a single in-plane orientation of YBa2Cu3O7, and results in superior superconducting properties. In particular, surface resistance Rs values of 1.4 m¿ have been measured at 8 GHz and 65 K. The attainment of such low values of Rs constitutes a key step toward the incorporation of high Tc materials as electrodes in photonic and acoustic devices.

Perovskite-based heterostructures integrating ferromagnetic-insulating La0.1Bi0.9MnO3

We report on the growth of thin films and heterostructures of the ferromagnetic-insulating perovskite La0.1Bi0.9MnO3. We show that the La0.1Bi0.9MnO3 perovskite grows single phased, epitaxially, and with a single out-of-plane orientation either on SrTiO3 substrates or onto strained La2/3Sr1/3MnO3 and SrRuO3 ferromagnetic-metallic buffer layers. We discuss the magnetic properties of the La0.1Bi0.9MnO3 films and heterostructures in view of their possible potential as magnetoelectric or spin-dependent tunneling devices.

Reduced microwave losses of YBa2Cu3O7_thin films on electro-optic LiNbO3 crystals

We report on the growth of epitaxial YBa2Cu3O7 thin films on X-cut LiNbO3 single crystals. The use of double CeO2/YSZ buffer layers allows a single in-plane orientation of YBa2Cu3O7, and results in superior superconducting properties. In particular, surface resistance Rs values of 1.4 m¿ have been measured at 8 GHz and 65 K. The attainment of such low values of Rs constitutes a key step toward the incorporation of high Tc materials as electrodes in photonic and acoustic devices.

Targeted cell elimination reveals an auxin-guided biphasic mode of lateral root initiation.

To sustain a lifelong ability to initiate organs, plants retain pools of undifferentiated cells with a preserved proliferation capacity. The root pericycle represents a unique tissue with conditional meristematic activity, and its tight control determines initiation of lateral organs. Here we show that the meristematic activity of the pericycle is constrained by the interaction with the adjacent endodermis. Release of these restraints by elimination of endodermal cells by single-cell ablation triggers the pericycle to re-enter the cell cycle. We found that endodermis removal substitutes for the phytohormone auxin-dependent initiation of the pericycle meristematic activity. However, auxin is indispensable to steer the cell division plane orientation of new organ-defining divisions. We propose a dual, spatiotemporally distinct role for auxin during lateral root initiation. In the endodermis, auxin releases constraints arising from cell-to-cell interactions that compromise the pericycle meristematic activity, whereas, in the pericycle, auxin defines the orientation of the cell division plane to initiate lateral roots.

Preparation of films of a highly aligned lipid cubic phase

We demonstrate a method by which we can produce an oriented film of an inverse bicontinuous cubic phase (QII D) formed by the lipid monoolein (MO). By starting with the lipid as a disordered precursor (the L3 phase) in the presence of butanediol, we can obtain a film of the QII D phase showing a high degree of in-plane orientation by controlled dilution of the sample under shear within a linear flow cell. We demonstrate that the direction of orientation of the film is different from that found in the oriented bulk material that we have reported previously; therefore, we can now reproducibly form QII D samples oriented with either the [110] or the [100] axis aligned in the flow direction depending on the method of preparation. The deposition of MO as a film, via a moving fluid− air interface that leaves a coating of MO in the L3 phase on the capillary wall, leads to a sample in the [110] orientation. This contrasts with the bulk material that we have previously demonstrated to be oriented in the [100] direction, arising from flow producing an oriented bulk slug of material within the capillary tube. The bulk sample contains significant amounts of residual butanediol, which can be estimated from the lattice parameter of the QII D phase obtained. The sample orientation and lattice parameters are determined from synchrotron small-angle X-ray scattering patterns and confirmed by simulations. This has potential applications in the production of template materials and the growth of protein crystals for crystallography as well as deepening our understanding of the mechanisms underlying the behavior of lyotropic liquid-crystal phases.

Surface chemistry of alanine on Cu{111}: Adsorption geometry and temperature dependence

Adsorption of l-alanine on the Cu{111} single crystal surface was investigated as a model system for interactions between small chiral modifier molecules and close-packed metal surfaces. Synchrotron-based X-ray photoelectron spectroscopy (XPS) and near-edge X-ray absorption fine structure (NEXAFS) spectroscopy are used to determine the chemical state, bond coordination and out-of-plane orientation of the molecule on the surface. Alanine adsorbs in its anionic form at room temperature, whilst at low temperature the overlayer consists of anionic and zwitterionic molecules. NEXAFS spectra exhibit a strong angular dependence of the π ⁎ resonance associated with the carboxylate group, which allows determining the tilt angle of this group with respect to the surface plane (48° ± 2°) at room temperature. Low-energy electron diffraction (LEED) shows a p(2√13x2√13)R13° superstructure with only one domain, which breaks the mirror symmetry of the substrate and, thus, induces global chirality to the surface. Temperature-programmed XPS (TP-XPS) and temperature-programmed desorption (TPD) experiments indicate that the zwitterionic form converts into the anionic species (alaninate) at 293 K. The latter desorbs/decomposes between 435 K and 445 K.

Surface chemistry of alanine on Ni{111}

The adsorption of L-alanine on Ni{111} has been studied as a 10 model of enantioselective heterogeneous catalysts. Synchrotron-based X-ray 11 photoelectron spectroscopy and near-edge X-ray absorption fine structure 12 (NEXAFS) spectroscopy were used to determine the chemical state, bond 13 coordination, and out-of-plane orientation of the molecule on the surface. 14 Alanine adsorbs in anionic and zwitterionic forms between 250 and ≈320 K. 15 NEXAFS spectra exhibit a strong angular dependence of the π* resonance 16 associated with the carboxylate group, which is compatible with two distinct 17 orientations with respect to the surface corresponding to the bidentate and 18 tridentate binding modes. Desorption and decomposition begin together at 19 ≈300 K, with decomposition occurring in a multistep process up to ≈450 K. Comparison with previous studies of amino acid 20 adsorption on metal surfaces shows that this is among the lowest decomposition temperatures found so far and lower than typical 21 temperatures used for hydrogenation reactions where modified Ni catalysts are used.

Modeling the growth of LT and TL-oriented fatigue cracks in longitudinally and transversely pre-strained Al 2524-T3 alloy

The aluminum alloy 2524 (Al-Cu-Mg) was developed during the 90s mainly to be employed in aircraft fuselage panels, replacing the standard Al 2024. In the present analysis the fatigue crack growth (FCG) behavior of 2524-T3 was investigated, regarding the influence of three parameters: load ratio, pre strain and crack plane orientation of the material. The pre strain of aluminum alloys is usually performed in order to obtain a more homogeneous precipitates distribution, accompanied by an increase in the yield strength. In this work, it was evaluated the resistance of Al 2524-T3 sheet samples to the fatigue crack growth, having L-T and T-L crack orientations. FCG tests were performed under constant amplitude loading at three distinct positive load ratios. The three material conditions were tested: as received(AR), pre strained longitudinally (SL) and transversally (ST) in relation to rolling direction. In order to describe FCG behavior, two-parameter kinetic equations were compared: a Paris-type potential model and a new exponential equation introduced in a previous work conducted by our research group. It was observed that the exponential model, which takes into account the deviations from linearity presented by da/dN versus AK data, describes more adequately the FCG behavior of Al 224-T3 in relation to load ratio, pre strain effects and crack plane orientation. © 2011 Published by Elsevier Ltd.

Genetic Control of Plant Development by Overriding a Geometric Division Rule

Formative cell divisions are critical for multicellular patterning. In the early plant embryo, such divisions follow from orienting the division plane. A major unanswered question is how division plane orientation is genetically controlled, and in particular whether this relates to cell geometry. We have generated a complete 4D map of early Arabidopsis embryogenesis and used computational analysis to demonstrate that several divisions follow a rule that uses the smallest wall area going through the center of the cell. In other cases, however, cell division clearly deviates from this rule, which invariably leads to asymmetric cell division. By analyzing mutant embryos and through targeted genetic perturbation, we show that response to the hormone auxin triggers a deviation from the ``shortest wall'' rule. Our work demonstrates that a simple default rule couples division orientation to cell geometry in the embryo and that genetic regulation can create patterns by overriding the default rule.

Development of One Meter Long Double-Sided CeO2 Buffered Ni-5at.W Templates by Reel-to-Reel Chemical Solution Deposition Route

High performance long-length coated conductors fabricated using various techniques have attracted a lot of interest recently. In this work, a reel-to-reel design for depositing double-sided coatings on long-length flexible metallic tapes via a chemical solution method is proposed and realized. The major achievement of the design is to combine the dip coating and drying processes in order to overcome the technical difficulties of dealing with the wet films on both sides of the tape. We report the successful application of the design to fabricate a one-meter-long double side coated CeO2/Ni-5at%W template. The CeO2 films on both sides exhibit a dense, crack-free morphology, and a high fraction of cube texture on the surface. Homogeneity studies on global texture over the length also reveal that the average full width at half maximum values of the in-plane and out-of-plane orientation on the CeO2 layer are 7.2 ° and 5.8° with standard deviation of 0.26° and 0.34°, respectively, being indicative of the high quality epitaxial growth of the films prepared in the continuous manner. An all chemical solution derived YBCOLow-TFA/Ce0.9La0.1O2 /Gd2Zr2O7/CeO2 structure is obtained on a short sample, demonstrating the possibility of producing long-length texture templates for coated conductors by this low cost deposition route.

Colossal anisotropy in diluted magnetic topological insulators

We consider dilute magnetic doping in the surface of a three dimensional topological insulator where a two dimensional Dirac electron gas resides. We find that exchange coupling between magnetic atoms and the Dirac electrons has a strong and peculiar effect on both. First, the exchange-induced single ion magnetic anisotropy is very large and favors off-plane orientation. In the case of a ferromagnetically ordered phase, we find a colossal magnetic anisotropy energy, of the order of the critical temperature. Second, a persistent electronic current circulates around the magnetic atom and, in the case of a ferromagnetic phase, around the edges of the surface.

Sviluppo e applicazione di nuovi criteri per la verifica a fatica multiassiale di componenti strutturali in leghe di acciaio e alluminio

La presente Tesi ha per oggetto lo sviluppo e la validazione di nuovi criteri per la verifica a fatica multiassiale di componenti strutturali metallici . In particolare, i nuovi criteri formulati risultano applicabili a componenti metallici, soggetti ad un’ampia gamma di configurazioni di carico: carichi multiassiali variabili nel tempo, in modo ciclico e random, per alto e basso/medio numero di cicli di carico. Tali criteri costituiscono un utile strumento nell’ambito della valutazione della resistenza/vita a fatica di elementi strutturali metallici, essendo di semplice implementazione, e richiedendo tempi di calcolo piuttosto modesti. Nel primo Capitolo vengono presentate le problematiche relative alla fatica multiassiale, introducendo alcuni aspetti teorici utili a descrivere il meccanismo di danneggiamento a fatica (propagazione della fessura e frattura finale) di componenti strutturali metallici soggetti a carichi variabili nel tempo. Vengono poi presentati i diversi approcci disponibili in letteratura per la verifica a fatica multiassiale di tali componenti, con particolare attenzione all'approccio del piano critico. Infine, vengono definite le grandezze ingegneristiche correlate al piano critico, utilizzate nella progettazione a fatica in presenza di carichi multiassiali ciclici per alto e basso/medio numero di cicli di carico. Il secondo Capitolo è dedicato allo sviluppo di un nuovo criterio per la valutazione della resistenza a fatica di elementi strutturali metallici soggetti a carichi multiassiali ciclici e alto numero di cicli. Il criterio risulta basato sull'approccio del piano critico ed è formulato in termini di tensioni. Lo sviluppo del criterio viene affrontato intervenendo in modo significativo su una precedente formulazione proposta da Carpinteri e collaboratori nel 2011. In particolare, il primo intervento riguarda la determinazione della giacitura del piano critico: nuove espressioni dell'angolo che lega la giacitura del piano critico a quella del piano di frattura vengono implementate nell'algoritmo del criterio. Il secondo intervento è relativo alla definizione dell'ampiezza della tensione tangenziale e un nuovo metodo, noto come Prismatic Hull (PH) method (di Araújo e collaboratori), viene implementato nell'algoritmo. L'affidabilità del criterio viene poi verificata impiegando numerosi dati di prove sperimentali disponibili in letteratura. Nel terzo Capitolo viene proposto un criterio di nuova formulazione per la valutazione della vita a fatica di elementi strutturali metallici soggetti a carichi multiassiali ciclici e basso/medio numero di cicli. Il criterio risulta basato sull'approccio del piano critico, ed è formulato in termini di deformazioni. In particolare, la formulazione proposta trae spunto, come impostazione generale, dal criterio di fatica multiassiale in regime di alto numero di cicli discusso nel secondo Capitolo. Poiché in presenza di deformazioni plastiche significative (come quelle caratterizzanti la fatica per basso/medio numero di cicli di carico) è necessario conoscere il valore del coefficiente efficace di Poisson del materiale, vengono impiegate tre differenti strategie. In particolare, tale coefficiente viene calcolato sia per via analitica, che per via numerica, che impiegando un valore costante frequentemente adottato in letteratura. Successivamente, per validarne l'affidabilità vengono impiegati numerosi dati di prove sperimentali disponibili in letteratura; i risultati numerici sono ottenuti al variare del valore del coefficiente efficace di Poisson. Inoltre, al fine di considerare i significativi gradienti tensionali che si verificano in presenza di discontinuità geometriche, come gli intagli, il criterio viene anche esteso al caso dei componenti strutturali intagliati. Il criterio, riformulato implementando il concetto del volume di controllo proposto da Lazzarin e collaboratori, viene utilizzato per stimare la vita a fatica di provini con un severo intaglio a V, realizzati in lega di titanio grado 5. Il quarto Capitolo è rivolto allo sviluppo di un nuovo criterio per la valutazione del danno a fatica di elementi strutturali metallici soggetti a carichi multiassiali random e alto numero di cicli. Il criterio risulta basato sull'approccio del piano critico ed è formulato nel dominio della frequenza. Lo sviluppo del criterio viene affrontato intervenendo in modo significativo su una precedente formulazione proposta da Carpinteri e collaboratori nel 2014. In particolare, l’intervento riguarda la determinazione della giacitura del piano critico, e nuove espressioni dell'angolo che lega la giacitura del piano critico con quella del piano di frattura vengono implementate nell'algoritmo del criterio. Infine, l’affidabilità del criterio viene verificata impiegando numerosi dati di prove sperimentali disponibili in letteratura.