Frequency-adjustable positive sequence detector for power conditioning applications

This paper proposes a novel and simple positive sequence detector (PSD), which is inherently self-adjustable to fundamental frequency deviations by means of a software-based PLL (Phase Locked Loop). Since the proposed positive sequence detector is not based on Fortescue's classical decomposition and no special input filtering is needed, its dynamic response may be as fast as one fundamental cycle. The digital PLL ensures that the positive sequence components can be calculated even under distorted waveform conditions and fundamental frequency deviations. For the purpose of validating the proposed models, the positive sequence detector has been implemented in a PC-based Power Quality Monitor and experimental results illustrate its good performance. The PSD algorithm has also been evaluated in the control loop of a Series Active Filter and simulation results demonstrate its effectiveness in a closed-loop system. Moreover, considering single-phase applications, this paper also proposes a general single-phase PLL and a Fundamental Wave Detector (FWD) immune to frequency variations and waveform distortions. © 2005 IEEE.

Optimization of left turn phase sequence in signalized closed networks. Final report.

Mode of access: Internet.

Effets des recuits ultra-rapides (10^5 K/s) sur la formation des siliciures métalliques en phase solide

La synthèse de siliciures métalliques sous la forme de films ultra-minces demeure un enjeu majeur en technologie CMOS. Le contrôle du budget thermique, afin de limiter la diffusion des dopants, est essentiel. Des techniques de recuit ultra-rapide sont alors couramment utilisées. Dans ce contexte, la technique de nanocalorimétrie est employée afin d'étudier, in situ, la formation en phase solide des siliciures de Ni à des taux de chauffage aussi élevés que 10^5 K/s. Des films de Ni, compris entre 9.3 et 0.3 nm sont déposés sur des calorimètres avec un substrat de a-Si ou de Si(100). Des mesures de diffraction de rayons X, balayées en température à 3 K/s, permettent de comparer les séquences de phase obtenues à bas taux de chauffage sur des échantillons de contrôle et à ultra-haut taux de chauffage sur les calorimètres. En premier lieu, il est apparu que l'emploi de calorimètres de type c-NC, munis d'une couche de 340 nm de Si(100), présente un défi majeur : un signal endothermique anormal vient fausser la mesure à haute température. Des micro-défauts au sein de la membrane de SiNx créent des courts-circuits entre la bande chauffante de Pt du calorimètre et l'échantillon métallique. Ce phénomène diminue avec l'épaisseur de l'échantillon et n'a pas d'effet en dessous de 400 °C tant que les porteurs de charge intrinsèques au Si ne sont pas activés. Il est possible de corriger la mesure de taux de chaleur en fonction de la température avec une incertitude de 12 °C. En ce qui a trait à la formation des siliciures de Ni à ultra-haut taux de chauffage, l'étude montre que la séquence de phase est modifiée. Les phases riches en m étal, Ni2Si et théta, ne sont pas détectées sur Si(100) et la cinétique de formation favorise une amorphisation en phase solide en début de réaction. Les enthalpies de formation pour les couches de Ni inférieures à 10 nm sont globalement plus élevées que dans le cas volumique, jusqu' à 66 %. De plus, les mesures calorimétriques montrent clairement un signal endothermique à haute température, témoignant de la compétition que se livrent la réaction de phase et l'agglomération de la couche. Pour les échantillons recuits a 3 K/s sur Si(100), une épaisseur critique telle que décrite par Zhang et Luo, et proche de 4 nm de Ni, est supposée. Un modèle est proposé, basé sur la difficulté de diffusion des composants entre des grains de plus en plus petits, afin d'expliquer la stabilité accrue des couches de plus en plus fines. Cette stabilité est également observée par nanocalorimétrie à travers le signal endothermique. Ce dernier se décale vers les hautes températures quand l'épaisseur du film diminue. En outre, une 2e épaisseur critique, d'environ 1 nm de Ni, est remarquée. En dessous, une seule phase semble se former au-dessus de 400 °C, supposément du NiSi2.

Synthèse de couches ultra-minces de siliciures sur silicium cristallin et endommagé étudiée par microscopie et profilométrie en profondeur

Les siliciures métalliques constituent un élément crucial des contacts électriques des transistors que l'on retrouve au coeur des circuits intégrés modernes. À mesure qu'on réduit les dimensions de ces derniers apparaissent de graves problèmes de formation, liés par exemple à la limitation des processus par la faible densité de sites de germination. L'objectif de ce projet est d'étudier les mécanismes de synthèse de siliciures métalliques à très petite échelle, en particulier le NiSi, et de déterminer l’effet de l’endommagement du Si par implantation ionique sur la séquence de phase. Nous avons déterminé la séquence de formation des différentes phases du système Ni-Si d’échantillons possédant une couche de Si amorphe sur lesquels étaient déposés 10 nm de Ni. Celle-ci a été obtenue à partir de mesures de diffraction des rayons X résolue en temps et, pour des échantillons trempés à des températures critiques du processus, l’identité des phases et la composition et la microstructure ont été déterminées par mesures de figures de pôle, spectrométrie par rétrodiffusion Rutherford et microscopie électronique en transmission (TEM). Nous avons constaté que pour environ la moitié des échantillons, une réaction survenait spontanément avant le début du recuit thermique, le produit de la réaction étant du Ni2Si hexagonal, une phase instable à température de la pièce, mélangée à du NiSi. Dans de tels échantillons, la température de formation du NiSi, la phase d’intérêt pour la microélectronique, était significativement abaissée.

Energetic electron signatures in an active magnetotail plasma sheet

Particles with energies of tens to hundreds of keV provide a powerful diagnostic of the acceleration processes that characterise the Earth’s magnetosphere, in particular the highly dynamic nightside plasma sheet. Such energetic particles can be detected by the RAPID experiment, onboard the quartet of Cluster spacecraft. We present results from the study of a series of quasi-periodic, intense energetic electron signatures in the magnetotail revealed by RAPID Imaging Electron Spectrometer (IES) observations some 19 Earth radii (RE) downtail, associated with the passage of a highly geoeffective, high-speed solar wind stream. The RAPID-IES signatures – interpreted in combination with magnetic field and lower-energy electron measurements from the FGM and PEACE experiments on Cluster, respectively, and with reference to energetic electron observations from the CEPPAD-IES instrument on Polar – are understood in terms of repeated encounters of the Cluster spacecraft with the tail plasma sheet in response to the resultant tail reconfiguration in each of a series of substorms. We consider the Cluster response for two of these substorms (identified according to the conventional expansion phase onset indicators of particle injection at geosynchronous orbit and Pi2 pulsations at Earth) in terms of two possible tail configurations in which a Near-Earth Neutral Line forms either antisunward or sunward of the Cluster spacecraft. The latter scenario, in which the reconnection X-line is assumed to form sunward of Cluster and subsequently migrate downtail such that the spacecraft become engulfed in a tailward expanding plasma sheet, is shown to be more consistent with the observations.

Reproductive ecology of the freshwater red alga Batrachospermum delicatulum (Batrachospermales, Rhodophyta) in three tropical streams

Batrachospermum delicatulum specimens from three stream segments were analyzed from a tropical region in south-eastern Brazil (20°18′- 20°49′S, 49°13′-49°46′W). Physical and chemical parameters and the spatial placement of thalli were investigated along with the reproductive characteristics of the gametophytic phase. Sequence data of the cox 2-3 spacer region was also utilized to evaluate genetic variation in individuals within and among stream segments. Gametophyte occurred under relatively diverse environmental conditions, whereas thalli abundance was weakly or not correlated to environmental variables within the stream segments. All specimens examined were dioecious. The ratio of male/female plants was relatively low (0.5 to 1.3) and male plants tended to occur as clumps (two or three plants together). High reproductive success was observed, as indicated by the occurrence of 100% fertilized (carposporophytic) female plants. This is similar to previous reports for this and other dioecious species, which is remarkable considering the relatively low proportion of male/female plants. Results support the two hypotheses to explain the high reproductive success in dioecious species. The occurrence of male plants in clumps was evidence for a strict spatial relationship (i.e. male plants located in upstream position of female plants in order to release spermatia, which would be carried by eddies through female plants). In contrast, the occurrence of male and female plants adjacent to each other allowed outcrossing among neighboring plants with intermingled male and female branches, which seemed more applicable to some situations (low turbulence habitats). The cox 2-3 spacer region from the 18 individuals sequenced was 376 bp and the DNA sequence was identical with no base pair substitutions. Likewise, a previous study of another Batrachospermum species showed that the same haplotypes were present in all stream segments from the same drainage basin, even though the stream segments were a considerable distance apart. Short distance dispersal either by small birds or waterway connectivity might explain these findings.

Espacialização de informações na gestão de sistemas de abastecimento de água utilizando sistema de informação geográfica

Avaliar a espacialização de informações na gestão de Sistema de Abastecimento de Água (SAA). Para isso, foram definidos e adotados os dados da pesquisa (Fase 1), sendo dividido em dados de perdas reais, comerciais e Despesas de exploração. Na Fase 2, a base cartográfica da área de estudo e os dados adotados foram armazenados e organizados em Sistema de Informação Geográfica (SIG), utilizando o software ArcGis 9.3, onde foi construído o modelo de dados para a pesquisa, e definida a topologia a ser utilizada para identificação dos dados espacializados, a construção do banco de dados georreferenciado e a criação dos layers. Na fase 3 foi realizado o cálculo do balanço hídrico nas principais unidades dos SAAs estudados sendo determinadas as perdas na adução de água bruta, no tratamento, na reservação, e na distribuição. Na fase 4 foram calculados indicadores para avaliar o desempenho dos SAAs, como: índice de cobertura, índice total de perda real, índice de perda na arrecadação, índice de perda de faturamento, índice de consumo de energia em SAA, índice de despesas com energia elétrica, entre outros. Na fase 5 foi proposta a espacialização e apresentação em SIG dos resultados obtidos nas fases anteriores. Com isso, considerando os dados adotados, foi possível identificar os valores das perdas reais e dos indicadores de desempenho em cada setor do SAA estudado, sendo, por exemplo, o setor 9, o que apresentou maior índice de perda total, chegando a 59,10%, seguido dos setores 4, 8 e 5. A perda mais significante para o sistema foi a perda na distribuição, com o setor 9 apresentando perda de 57%; a perda no tratamento foi de 3,4%, no setor 3; e os setores com maior índice de perda na adução, foram os setores 6 e 8, com 3,5%. Os percentuais de água não faturada, foram maiores nos setores 1 e 5. Os setores 1, 3, 4 e 6 são os que apresentaram maior consumo de energia elétrica por volume de água produzido. Portanto, a espacialização dos dados em SIG facilitou a visualização e análise dos dados adotados na pesquisa.

Diagnostic techniques for EHD and MHD interaction

The impact of plasma technologies is growing both in the academic and in the industrial fields. Nowadays, a great interest is focused in plasma applications in aeronautics and astronautics domains. Plasma actuators based on the Magneto-Hydro-Dynamic (MHD) and Electro- Hydro-Dynamic (EHD) interactions are potentially able to suitably modify the fluid-dynamics characteristics around a flying body without utilizing moving parts. This could lead to the control of an aircraft with negligible response time, more reliability and improvements of the performance. In order to study the aforementioned interactions, a series of experiments and a wide number of diagnostic techniques have been utilized. The EHD interaction, realized by means of a Dielectric Barrier Discharge (DBD) actuator, and its impact on the boundary layer have been evaluated by means of two different experiments. In the first one a three phase multi-electrode flat panel actuator is used. Different external flow velocities (from 1 to 20m/s) and different values of the supplied voltage and frequency have been considered. Moreover a change of the phase sequence has been done to verify the influence of the electric field existing between successive phases. Measurements of the induced speed had shown the effect of the supply voltage and the frequency, and the phase order in the momentum transfer phenomenon. Gains in velocity, inside the boundary layer, of about 5m/s have been obtained. Spectroscopic measurements allowed to determine the rotational and the vibrational temperature of the plasma which lie in the range of 320 ÷ 440°K and of 3000 ÷ 3900°K respectively. A deviation from thermodynamic equilibrium had been found. The second EHD experiment is realized on a single electrode pair DBD actuator driven by nano-pulses superimposed to a DC or an AC bias. This new supply system separates the plasma formation mechanism from the acceleration action on the fluid, leading to an higher degree of the control of the process. Both the voltage and the frequency of the nano-pulses and the amplitude and the waveform of the bias have been varied during the experiment. Plasma jets and vortex behavior had been observed by means of fast Schlieren imaging. This allowed a deeper understanding of the EHD interaction process. A velocity increase in the boundary layer of about 2m/s had been measured. Thrust measurements have been performed by means of a scales and compared with experimental data reported in the literature. For similar voltage amplitudes thrust larger than those of the literature, had been observed. Surface charge measurements led to realize a modified DBD actuator able to obtain similar performances when compared with that of other experiments. However in this case a DC bias replacing the AC bias had been used. MHD interaction experiments had been carried out in a hypersonic wind tunnel in argon with a flow of Mach 6. Before the MHD experiments a thermal, fluid-dynamic and plasma characterization of the hypersonic argon plasma flow have been done. The electron temperature and the electron number density had been determined by means of emission spectroscopy and microwave absorption measurements. A deviation from thermodynamic equilibrium had been observed. The electron number density showed to be frozen at the stagnation region condition in the expansion through the nozzle. MHD experiments have been performed using two axial symmetric test bodies. Similar magnetic configurations were used. Permanent magnets inserted into the test body allowed to generate inside the plasma azimuthal currents around the conical shape of the body. These Faraday currents are responsible of the MHD body force which acts against the flow. The MHD interaction process has been observed by means of fast imaging, pressure and electrical measurements. Images showed bright rings due to the Faraday currents heating and exciting the plasma particles. Pressure measurements showed increases of the pressure in the regions where the MHD interaction is large. The pressure is 10 to 15% larger than when the MHD interaction process is silent. Finally by means of electrostatic probes mounted flush on the test body lateral surface Hall fields of about 500V/m had been measured. These results have been used for the validation of a numerical MHD code.

Strukturen und Phasen des beta-Eukryptits sowie die Sammlung von Beugungsdaten mit axialen q-Scans

Der 'gestopfte Hochquarz' ß-Eukryptit (LiAlSiO4) ist bekannt für seine außergewöhnliche anisotrope Li-Ionenleitfähigkeit und die nahe Null liegende thermische Ausdehnung.Untersucht wurde die temperaturabhängige ß-Eukryptit-Phasenabfolge, insbesondere die modulierte Phase. Deren Satellitenreflexe sind gegenüber den normalen Reflexen erheblich verbreitert, überlappen miteinander sowie mit den dazwischen liegenden 'a-Reflexen' zu Tripletts. Für die Separation der Triplett-Intensitäten waren bisherige Standardverfahren zur Beugungsdatensammlung ungeeignet. Mit 'axialen q-Scans' wurde ein neuartiges Verfahren entwickelt. Intensitäten wurden mit dem neu-entwickelten least squares-Programm GKLS aus 2000 Profilen seriell und automatisch gewonnen und erfolgreich auf Standarddaten skaliert. Die Verwendung verbreiterter Reflexprofile erwies sich als zulässig.Die Verbreiterung wurde auf eine verminderte Fernordnung der Modulation von 11 bis 16 Perioden zurückgeführt (Analyse mit der Gitterfunktion), womit ein ungewöhnliches beugungswinkelabhängiges Verhalten der Reflexbreiten korrespondiert und mit typischen Antiphasendomänendurchmessern (andere Autoren) korreliert.Eine verminderte Si-/ Al-Ordnung wird als ursächlich für geringe Domänengrößen und Fernordnung angesehen, sowie für Eigenschaften wie z.B. a/c-Verhältnisse, Ausdehnungskoeffizienten, Ionenleitfähigkeit, Strukturtyp und Umwandlungstemperaturen. Änderungen des SiO2-Gehaltes, der Temperatur oder der Si- /Al-Ordnung zeitigen für einige Eigenschaften ähnliche Wirkungen.Die gemittelte Struktur der modulierten Phase wurde erstmals zuverlässig bestimmt, die Rolle des Li charakterisiert, Zweifel an der hexagonalen Symmetrie des ß-Eukryptits wurden ausgeräumt und die Bestimmung der modulierten Struktur wurde weitgehend vorbereitet.

Optimization of adaptive traffic signal control with transit signal priority at isolated intersections using parallel genetic algorithms

Optimization of adaptive traffic signal timing is one of the most complex problems in traffic control systems. This dissertation presents a new method that applies the parallel genetic algorithm (PGA) to optimize adaptive traffic signal control in the presence of transit signal priority (TSP). The method can optimize the phase plan, cycle length, and green splits at isolated intersections with consideration for the performance of both the transit and the general vehicles. Unlike the simple genetic algorithm (GA), PGA can provide better and faster solutions needed for real-time optimization of adaptive traffic signal control. ^ An important component in the proposed method involves the development of a microscopic delay estimation model that was designed specifically to optimize adaptive traffic signal with TSP. Macroscopic delay models such as the Highway Capacity Manual (HCM) delay model are unable to accurately consider the effect of phase combination and phase sequence in delay calculations. In addition, because the number of phases and the phase sequence of adaptive traffic signal may vary from cycle to cycle, the phase splits cannot be optimized when the phase sequence is also a decision variable. A "flex-phase" concept was introduced in the proposed microscopic delay estimation model to overcome these limitations. ^ The performance of PGA was first evaluated against the simple GA. The results show that PGA achieved both faster convergence and lower delay for both under- or over-saturated traffic conditions. A VISSIM simulation testbed was then developed to evaluate the performance of the proposed PGA-based adaptive traffic signal control with TSP. The simulation results show that the PGA-based optimizer for adaptive TSP outperformed the fully actuated NEMA control in all test cases. The results also show that the PGA-based optimizer was able to produce TSP timing plans that benefit the transit vehicles while minimizing the impact of TSP on the general vehicles. The VISSIM testbed developed in this research provides a powerful tool to design and evaluate different TSP strategies under both actuated and adaptive signal control. ^

Simulating the aggregation of DNA oligonucleotides

In this work we have studied, by means of Molecular Dynamics simulations, the process of denaturation and self-assembly of short oligonucleotides. Supramolecular ordering of DNA short strands is a promising field which is constantly enriched with new findings. Examples are provided by micellar and fibrils formations and due to the selectivity of DNA bindings, "intelligent" devices have been developed to perform simple logic operations. It is worth to notice that computer simulations of these DNA nanosystems would complement experiments with detailed insight into processes involved in self-assembly. In order to obtain an accurate description of the interactions involved in the complex structure of DNA we used oxDNA, a coarse-grained model developed by Ouldridge. We simulated the melting transition of 4, 6, and 8 base pair sequences. Sequence and length dependence were analyzed, specifically we compared thermodynamic parameters DeltaH, DeltaS and the melting temperature with literature results. Moreover, we have attempted to reproduce liquid crystal ordering of the ultrashort sequence GCCG at relatively high saline concentration, until now only experimentally observed in Bellini's works. We found that our simple model successfully reproduces the experimental phase sequence (isotropic, nematic, columnar) at T= 5 °C as a function of oligonucleotide concentration, and we fully characterized the microscopic structure of the three phases.

Estimation of zero-sequence impedance of undergrounds cables for single-phase fault location in distribution systems with electric arc

This paper focus on the problem of locating single-phase faults in mixed distribution electric systems, with overhead lines and underground cables, using voltage and current measurements at the sending-end and sequence model of the network. Since calculating series impedance for underground cables is not as simple as in the case of overhead lines, the paper proposes a methodology to obtain an estimation of zero-sequence impedance of underground cables starting from previous single-faults occurred in the system, in which an electric arc occurred at the fault location. For this reason, the signal is previously pretreated to eliminate its peaks voltage and the analysis can be done working with a signal as close as a sinus wave as possible

Indicators of therapeutic effect in FIT-06, a Phase II trial of a DNA vaccine, GTU(®)-Multi-HIVB, in untreated HIV-1 infected subjects.

BACKGROUND: Combination highly active antiretroviral therapy (HAART) has significantly decreased HIV-1 related morbidity and mortality globally transforming HIV into a controllable condition. HAART has a number of limitations though, including limited access in resource constrained countries, which have driven the search for simpler, affordable HIV-1 treatment modalities. Therapeutic HIV-1 vaccines aim to provide immunological support to slow disease progression and decrease transmission. We evaluated the safety, immunogenicity and clinical effect of a novel recombinant plasmid DNA therapeutic HIV-1 vaccine, GTU(®)-multi-HIVB, containing 6 different genes derived from an HIV-1 subtype B isolate. METHODS: 63 untreated, healthy, HIV-1 infected, adults between 18 and 40 years were enrolled in a single-blinded, placebo-controlled Phase II trial in South Africa. Subjects were HIV-1 subtype C infected, had never received antiretrovirals, with CD4 ≥ 350 cells/mm(3) and pHIV-RNA ≥ 50 copies/mL at screening. Subjects were allocated to vaccine or placebo groups in a 2:1 ratio either administered intradermally (ID) (0.5mg/dose) or intramuscularly (IM) (1mg/dose) at 0, 4 and 12 weeks boosted at 76 and 80 weeks with 1mg/dose (ID) and 2mg/dose (IM), respectively. Safety was assessed by adverse event monitoring and immunogenicity by HIV-1-specific CD4+ and CD8+ T-cells using intracellular cytokine staining (ICS), pHIV-RNA and CD4 counts. RESULTS: Vaccine was safe and well tolerated with no vaccine related serious adverse events. Significant declines in log pHIV-RNA (p=0.012) and increases in CD4+ T cell counts (p=0.066) were observed in the vaccine group compared to placebo, more pronounced after IM administration and in some HLA haplotypes (B*5703) maintained for 17 months after the final immunisation. CONCLUSIONS: The GTU(®)-multi-HIVB plasmid recombinant DNA therapeutic HIV-1 vaccine is safe, well tolerated and favourably affects pHIV-RNA and CD4 counts in untreated HIV-1 infected individuals after IM administration in subjects with HLA B*57, B*8101 and B*5801 haplotypes.

Estimation of zero-sequence impedance of undergrounds cables for single-phase fault location in distribution systems with electric arc

This paper focus on the problem of locating single-phase faults in mixed distribution electric systems, with overhead lines and underground cables, using voltage and current measurements at the sending-end and sequence model of the network. Since calculating series impedance for underground cables is not as simple as in the case of overhead lines, the paper proposes a methodology to obtain an estimation of zero-sequence impedance of underground cables starting from previous single-faults occurred in the system, in which an electric arc occurred at the fault location. For this reason, the signal is previously pretreated to eliminate its peaks voltage and the analysis can be done working with a signal as close as a sinus wave as possible