CO2 Laser Cutting of Particleboard, HDF and MDF

The purpose of this thesis is to reveal how the laser cutting parameters influence lasercutting of particleboard, HDF and MDF. The literature review introduces the basic principle of CO2 laser, CO2 laser equipment and its usage in cutting of wood-based materials. The experimental part focuses on the discussion and analysis ofthe test data and attempts to draw conclusions on the influence of various parameters, including laser power, focal length of the lens and cutting gas, on the cutting speed and kerf quality. The tested materials include various thicknesses of particleboard, HDF and MDF samples. A TRUMPF TLF2700 HQ laser equipment was used for the experiments. To obtain valid data, the test samples must be completely cut through without any bonding of wood fibre. The maximum cutting speed is linear dependent on the laser power in thecondition that the other parameters are constant. For each thickness of a specific material type, there is a minimum laser power for cutting. Normally, the topand bottom kerf widths increase with the enhancement of laser power. There may be a critical laser power which can generate the minimum cross-sectional kerf width. Lens of larger focal length may achieve higher cutting speed. As the focal length becomes larger, the top kerf width tends to increase while the bottom andcross-sectional kerf widths to the opposite. Of all cutting gases, oxygen can help achieve higher cutting speed. The gas pressure of nitrogen does not seem to have strong influence on the cutting result. Generally, 2 bar air is more preferable for higher cutting speed. For particleboard and MDF samples of larger thickness than 12 mm, 2 bar argon can be used to reach remarkably higher cutting speed than the 5 bar. Generally, the 190.5 mm lens can produce smallest total kerf width. The kerf sides of thicker samples are darker than the thinner ones. The sample darkness tends to be lower as laser power increased. 63.5 mm lens seemed tocause more darkness than other lens. 5 bar cutting gases can produce less dark side kerfs than 2 bar ones. Oxygen normally causes darker kerfs than other gases. No distinct differences were found between nitrogen and argon.

Prospects for the use of municipal tree pruning wastes in particleboard production

The purpose of this study was to evaluate the physical and mechanical properties of particleboard made with pruning wastes from Ipê (Tabebuia serratifolia) and Chapéu-de-Sol (Terminalia catappa) trees. Particleboards were prepared with both wood species, using all the material produced by grinding the pruning wastes. The particleboards had dimensions of 45×45 cm, a thickness of approximately 11.5 mm and an average density of 664 kg/m3. A urea-formaldehyde adhesive was used in the proportion of 12% of the dry particle mass. The particleboards were pressed at a temperature of 130 C for 10 mins. The physical and mechanical properties analyzed were density, moisture content, thickness swelling, percentage of lignin and cellulose, modulus of resilience, modulus of elasticity and tensile strength parallel to the grain, accordingly to the standards NBR 14810 and CS 236-66 (1968). The particleboards were considered to be of medium density. The particle size significantly affected the static bending strength and tensile strength parallel to the grain. Ipê presented better results, demonstrating a potential for the production and use of particleboard made from this species. © The Author(s) 2013.

Particleboard produced with sawmill waste of different wood species

This study aimed to investigate physical performance of particleboards produced with waste from sawmills, containing different wood species, and two adhesives: urea-formaldehyde (UF) based resin and castor-oil (PU) based bi-component polyurethane resin. Panels were produced with nominal density 0.8gcm(-3); pressing temperature 110 degrees C; pressing time 10 min; specific pressure 5 MPa. Water absorption (2 and 24h); thickness swelling (2 and 24h); density; and moisture content were investigated. Results confirmed that the produced panels presented compatible physical properties in comparison with other researches referred in literature, proving the feasibility of inputs employed. Panels produced PU showed better performance than those produced with UF.

Physical and mechanical properties of particleboard bamboo waste bonded with urea formaldehyde and castor oil based adhesive

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Medium density particleboard reinforced with bamboo laminas

The objective of this work was to evaluate the effect of the addition of bamboo laminas of the species Dendrocalamus giganteus to three-layer medium density particleboard (MDP). These laminas were glued onto both the top and the bottom of each panel. With the manufactured panels laminated with bamboo, mechanical tests based on the Brazilian Standard ABNT NBR 14810 were carried out to determine the modulus of rupture (MOR) in static bending and the tensile strength parallel-to-surface. These mechanical tests were realized in particleboards of eucalyptus and in reinforced particleboard, both produced in the laboratory. The modulus of rupture and tensile strength parallel-to-surface of the laminated MDP had values close to those that have been reported. The reinforcements increased the values of these studied properties. Nevertheless, this fact indicated the possibility to produce a stronger MDP using bamboo lamina as surface layers. These results show the possibility of using coatedbamboo MDP for utilization in large spans, for example, in flooring for mezzanines with finish on both sides, and for robust furniture as bookshelves, beds, tables, etc.

Physical characterization of particleboard produced with waste from ethanol and sugar mill

The problem of proper disposal of solid waste generated in different industrial processes is one of worldwide environmental concerns nowadays. Thus, this study aimed to establish a new alternative for the disposal of two agro-industrial residues employing them to produce particleboard for different purposes in building construction. The focus was given to the reuse of the sugarcane bagasse (SB) originated during the processing of Saccharum officinarum for sugar and ethanol production, and bamboo stem leaves of Dendrocalamus giganteus(BB). For this, six particleboards were produced in the following compositions: with 100% SB, 75% SB + 25% BB, 50% SB+50% BB, 40% SB +60 BB, 25% SB+ 75% BB and 100% BB in the total mass of the composites. The particleboards physical characterization followed Brazilian Standard ABNT NBR 14810-3 to density, moisture content and water absorption. Results showed these raw materials are compatible to particleboard production.

Study of the feasibility of mix of species from sawmill waste and limiting for particleboard

This study aims to determine physical properties of particleboard made of sawmill waste, as a mix of several wood species, and two adhesives: urea-formaldehyde, usually employed in industry (even with drawbacks or formaldehyde emission during pressing) and FASTBOND®, water based resin, still poorly referenced in literature. Sixteen panels have been produced, in four experimental conditions, defined by using two adhesives and a 12 mm thick limiter (or not). Variance analysis was adopted to evaluate influence of experimental conditions on physical properties of produced panels, manufactured in nominal dimensions 350x350mm; 10% resin related to particles mass (at 5% moisture); 3.5 MPa compaction pressure, temperature 130°C, in a 10 min cycle. Tests to determine density, moisture content, swelling and water absorption were carried out based on normative parameters of ABNT NBR 14810:2006. Results have been satisfactory to panels produced with urea-formaldehyde but those manufactured with polychloroprene based resin (FASTBOND®) not meet regulatory requirements. Best results have been obtained without limiter.

Propriedades físico-mecânicas de painéis de mdp (medium density particleboard) constituído de bambu e fibra de coco

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Fire-resistance, physical, and mechanical characterization of particleboard containing Oceanic Posidonia waste

In this work, particleboards manufactured with Oceanic Posidonia waste and bonded with cement are investigated. The particleboards are made with 3/1.5/0.5 parts of cement per part of Posidonia waste. The physical properties of bulk density, swelling, surface absorption, and dimensional changes due to relative humidity as well as the mechanical properties of modulus of elasticity, bending strength, surface soundness, perpendicular tensile strength and impact resistance are studied. In terms of the above properties, the best results were obtained for particleboards with high cement content and when the waste “leaves” are treated (crushed) before board fabrication, due to internal changes to the board structure under these conditions. Based on the results of fire tests, the particleboard is non-flammable without any fire-resistant treatment.

Environment-friendly soy flour-based resins without formaldehyde

Glyoxalated soy flour adhesives for wood particleboard added with a much smaller proportion of glyoxalated lignin or tannin and without any addition of either formaldehyde or formaldehyde-based resin are shown to yield results satisfying the relevant standard specifications for interior wood boards. Adhesive resin formulations in which the total content of natural material is either 70 or 80% of the total resin solids content gave good results. The resins comprising 70% by weight of natural material can be used in a much lower proportion on wood chips and can afford pressing times fast enough to be significant under industrial panel pressing conditions. The best formulation of all the ones tried was the one based on glyoxalated precooked soy flour (SG), to which a condensed tannin was added in water solution and a polymeric isocyanate (pMDI), where the proportions of the components SG/T/pMDI was 54/16/30 by weight. (C) 2008 Wiley Periodicals, Inc.

Material compósito - propriedades do aglomerado de gesso e partículas fragmentadas de bambu (phyllostachys edulis)

Neste trabalho estudou-se um compósito de gesso FGD reforçado com fibras vegetais. As fibras utilizadas neste estudo são provenientes de bambu da espécie Phyllostachys edulis e foram trituradas até se obter uma granulometria apropriada à composição de uma pasta de gesso que permitisse a execução de placas de gesso laminado. As placas produzidas foram ensaiadas à flexão e posteriormente submetidas à análise de humidade para aferir a percentagem de água de cristalização nas amostras. Foram ainda produzidos provetes cúbicos com 7cm de aresta para permitira a execução de ensaio à compressão. Foram produzidos dois tipos de pastas, uma sem a adição de partículas de bambu (controlo) e outra com adição de 15% de partículas de bambu.

Levyteollisuuden energia-, kustannus- ja ympäristövaikutukset

Kuluvien vuosien aikana ei ole tehty kattavia tutkimuksia levyteollisuuden sähkönkulutuksista, joten on aika selvittää suurimpien sähkökäyttöjen kulutukset sekä muodostaa tutkittaville tehtaille energiataseet. Tutkittavia tehtaita ovat OSB- ja lastulevytehtaat. Yksittäisten sähkömoottoreiden kulutukset saadaan selville käyttämällä hyväksi teoreettisia lähteitä, kenttä-ja laboratoriotutkimusta. Ympäristölainsäädäntö ja siihen kiinteästi liittyvä lupakäytäntö muodostavat levyteollisuudelle yhden viimeaikojen suurimmista haasteista. Tulevaisuudessa lainsäädäntö tulee vielä entisestäänkin kiristymään. Euroopan ympäristölainsäädäntö perustuu pitkälti yhtenäislupadirektiiviin eli IPPC-direktiiviin. Direktiivin keskeinen osa on ympäristöluvan hankkiminen, koska teollista toimintaa ei voi harjoittaa ilman hyväksyttyä viranomaisen lupaa. Lupa myös velvoittaa toiminnanharjoittajan käyttämään parasta käyttökelpoista tekniikkaa päästöjen kontrolloinnissa. Yhdysvalloissa parhaan käyttökelpoisen tekniikan (BAT) vaatimus on sisälletty ympäristövirasto EPA:n MACT-standardeihin. Levyteollisuuden tehtaista syntyvät päästöt ovat hyvin samankaltaisia. Tehtaista on helposti erotettavissa kaksi suurta päästölähdettä, joita ovat kuivaus ja kuumapuristus. Merkittävimpiä päästöjä ovat haihtuvat orgaaniset yhdisteet, hiukkaset, typen oksidit, hiilimonoksidi ja rikkidioksidit. Työn loppuosa on varattu tuotantojen kustannusvaikutusten ja tunnuslukujen tarkasteluille. Saatavilla tiedoilla on keskeinen rooli tehtaiden jokapäiväisessä toiminnassa. Analysoinnin tarpeeseen vaikuttaa osaltaan nykyisen toimintaympäristön muutosherkkyys ja levymarkkinoiden kireä kilpailutilanne.

Suuren kapasiteetin paloittelusahakonseptin kehittäminen

Asiakkaat vaativat lisää kapasiteettia ja joustavuutta eli levylinjan paloittelusahan tapauksessa pieniä palakokoja. Vaatimukseen on lähdetty vastaamaan tuotekehitysprojektilla, jonka yksi osa-alue on uuden paloittelusahan konseptin kehitys. Konseptin kehityksen lähtökohtana on ajatus terien lukumäärän lisäämisestä, terien suunnan kääntämisestä levypinkan liikesuunnan myötäiseksi, sekä terien pitämisestä paikallaan levypinkan liikkuessa niiden läpi. Tässä työssä konseptin kehitykseen kuuluu purunpoistojärjestelmä, sahattujen hukkapalojen käsittely, murskaus ja poisto, sekä levypinkan siirtomenetelmä sahauskokonaisuuden läpi. Kirjallisuusosassa on paneuduttu puulevyjen ja pyörösahauksen teoriaan. Diplomityössä on tutkittu eri pohjaratkaisujen vaikutusta kapasiteettiin, sekä vaihtoehtoja paloittelusahan eri osa-alueiden ratkaisuiksi. Lisäksi on tutkittu murskauksen tehovaatimusta vertaamalla mitattuja arvoja laskettuihin arvoihin. Tutkimuksen otannan puitteissa todettiin laskettujen arvojen johtavan reiluun moottoreiden ylimitoitukseen.

Propriedades de chapas de aglomerado fabricadas com adesivo tânico de angico-vermelho (Anadenanthera peregrina) e uréia-formadeído

O principal objetivo deste trabalho foi produzir chapas de aglomerado substituindo-se parcial ou totalmente os adesivos à base de uréia-formaldeído por adesivos de taninos extraídos da casca de angico-vermelho (Anadenanthera peregrina) e hidrolisados. As chapas de aglomerado foram fabricadas com partículas de Pinus elliottii e dimensões aproximadas de 40 x 40 x 1 cm, contendo 8% de sólidos de adesivo em relação à massa seca de partículas, sendo 100% de adesivo de uréia-formaldeído puro ou contendo 12,5, 25 e 37,5% de adesivo tânico. Foram produzidas, também, chapas com adesivos tânicos puros, constituindo um total de cinco tratamentos, com três repetições. As chapas foram fabricadas com densidade média de 0,7 g/cm³. As propriedades físicas e mecânicas das chapas foram determinadas em conformidade com a norma ASTM D-1037 (1993). Os resultados dos testes mecânicos foram comparados com os valores mínimos estabelecidos na norma ANSI/A 208.1-1993 (Wood Particleboard), enquanto os resultados dos testes de absorção de água e inchamento em espessura, comparados com os valores máximos estabelecidos na norma DIN 68m761 (1)-1961. A resistência mecânica das chapas de aglomerado produzidas com adesivos contendo taninos de angico-vermelho, com exceção do módulo de elasticidade, ultrapassou os valores mínimos requeridos na norma ANSI/A1-280/93. A absorção de água e o inchamento em espessura, após 2 e 24 h de imersão, de todas as chapas excederam o valor máximo estabelecido. Conclui-se que os adesivos de taninos de angico-vermelho podem substituir parcial ou totalmente o adesivo comercial de uréia-formaldeído, e as suas misturas são indicadas para uso interior, em que a resistência à umidade não é requerida.