985 resultados para Paredes tipo Berlim
Resumo:
Dissertação de natureza científica para obtenção do grau de Mestre em Engenharia Civil
Resumo:
O presente relatório tem como objectivo descrever o trabalho por mim desenvolvido, enquanto estagiário da empresa SONANGIL durante o período de Fevereiro a Agosto de 2009. Durante este período, acompanhei a execução de um parque de estacionamento subterrâneo em Almada, onde se procedeu à escavação de terras e respectivo transporte a vazadouro, execução da contenção periférica tipo “Berlim” e estrutura em betão armado. A intervenção da SONANGIL incidiu apenas na construção de um novo edifício destinado a estacionamento, com ligação a um outro parque já existente. A obra em estudo tem 4 pisos de estacionamento, com uma área em planta de aproximadamente 857 m2 com capacidade para 93 veículos, e um outro edifício já existente, que possui uma área de parqueamento de 540 m2 com capacidade para 59 veículos. Dado que a SONANGIL foi o subempreiteiro designado para a execução dos Projectos de Escavação, Contenção Periférica e Estabilidade, a minha função em obra ao longo dos 6 meses de estágio, consistiu em acompanhar e registar os trabalhos executados pela empresa, bem como, prestar o respectivo apoio técnico na preparação de obra.
Resumo:
Neste trabalho pretende-se estudar a influência das características geotécnicas e geométricas no dimensionamento de cortinas de contenção ancoradas. Para a concretização destes objetivos escolheu-se uma parede tipo Berlim definitivo ancorada, tendo-se abordado o seu processo construtivo e constatado a necessidade de o seguir com rigor. Concluído isto, fez-se uma introdução ao programa de elementos finitos, Phase2, da Rocsciense. A parte mais importante da presente dissertação visa perceber o funcionamento deste tipo de construção e o que mais influencia o seu comportamento. Após se ter admitido um modelo, as características do solo a utilizar, e compreendido de que forma poderia ser utilizado o software mencionado e como proceder à modelação que mais se aproxima de uma situação real, simulou-se o caso de estudo considerado e efetuou-se a sua análise do ponto de vista de deslocamentos horizontais na cortina. Esta primeira análise resultou em deslocamentos que, comparados com os dos casos de estudo referidos na bibliografia, se consideram aceitáveis. Após análise do estudo base, que será designado ao longo do trabalho por estudo base 1 (E1), procedeu-se a uma análise paramétrica, ou seja, realizaram-se vários estudos, onde para cada um deles se fez variar um parâmetro de cada vez. Esses parâmetros são propriedades geotécnicas do solo, características geométricas da parede e características dos elementos de ancoragem. No estudo 2, também designado por E2, utiliza-se uma parede moldada em substituição do muro de Berlim definitivo utilizado no E1. Estes estudos paramétricos vão desde o Estudo 2 (E2) ao Estudo 15 (E15) e todos eles são apresentados em comparação com o estudo base. Por fim, conclui-se que o comportamento entre o muro de Berlim definitivo e a parede moldada são diferentes, sobretudo na distribuição de deslocamentos ao longo da cortina, sendo esta diferença provocada essencialmente pelas diferenças no processo construtivo. Quanto à alteração dos parâmetros em estudo os que mais afetam o comportamento do muro são a variação do módulo de deformabilidade do solo, a presença de um estrato rijo ao nível do fundo da escavação, a variação da inclinação das ancoragens e a força de pré-esforço aplicada.
Resumo:
O presente trabalho visa a fornecer uma contribuição ao estudo dos perfis formados a frio sob altas temperaturas, em conseqüência da deflagração de um incêndio. Especificamente, abordam–se assuntos inerentes ao fenômeno da transferência de calor em paredes do tipo steel frame – dry wall com ou sem isolamento térmico na cavidade. Para tanto, propõem–se modelos computacionais capazes de fornecer, com certa precisão, o valor de temperatura em qualquer ponto do sistema estudado. Dessa forma, é possível, então, traçar configurações de distribuição de temperatura (uniforme ou não–uniforme) na seção transversal dos montantes que constituem o painel, fornecendo subsídios para análise de estabilidade e pós–flambagem dos elementos estruturais em questão. As simulações numéricas de transferência de calor são efetuadas com auxílio dos programas computacionais ABAQUS e SAFIR, ambos baseados no método dos elementos finitos.
Resumo:
Análisis instrumental mediante diferentes técnicas (ATR-IR, DRX, TG, SEM, MO, FRX, etc..) del recubrimiento de la pared interna de dos estructuras negativas (silos)del yacimiento Neolítico-Mesolítico de Cantera Benàmer (Muro d'Alcoi, Alicante).
Resumo:
Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)
Resumo:
Dissertação de Mestrado apresentada ao Instituto Superior de Contabilidade e Administração do Porto para a obtenção do grau de Mestre em Auditoria, sob orientação do Mestre Adalmiro Álvaro Malheiro de Castro Andrade Pereira
Resumo:
The present study aimed to characterize the thermal profile of wood fired oven used by the red ceramic industry in Parelhas, in the Seridó region/RN, aiming to propose structural interventions that can contribute to increasing productivity and product quality, optimize wood consumption and mitigate existing losses during the burning process. The study was conducted at Cerâmica Esperança in the city of Parelhas -RN, Brazil, during the period from August 2012 to September 2013. Four treatments were performed with three replicates, ie, with, a total of 12 experimental units (burnings). In the first stage 4 treatments were performed with three replicates, totaling 12 experimental units (firings). In the second stage 2 treatments were performed with three replications, totaling 6 experimental units (firings). The physical characteristics of the wood were analyzed using standard NBR 11941 and NBR 7190 for basic density and moisture, respectively. The clay was used as a reference parameter for distinguishing treatments. For both the analysis and characterization was carried out using techniques of fluorescence X (XRF) rays, X-ray diffraction (XRD) analysis, particle size analysis (FA). In the first and second stages were monitored: the time during the firing process, the amount of wood used at each firing, the number of parts enfornadas for subsequent determination of the percentages of losses, but also product quality. To characterize the thermal profile of the oven, we measured the temperature at 15 points scored in the surface charge put into the oven. Measurements were taken every 30 minutes from preheat until the end of burning, using a pyrometer laser sight sighting from preheating until the end of burning. In the second step 12 metal cylinders distributed on the oven walls, and the cylinder end walls 8 of the furnace 2 and rollers on each side walls are installed equidistant to 17 cm from the soil and the surface 30 of the wall are installed. The cylinders distributed on the front were placed 50 cm above the furnace, and the base of the oven 20 cm distant from the ground. 10 also thermocouples were installed, and five thermocouples distributed 1.77 cm above the combustion chambers, and one thermocouple on each side, and three thermocouples in front of the oven. We carried out the measurements of the temperatures every 1 hour during the burning two hours in cooling the cylinders with a pyrometer and thermocouples for dattaloger. These were fixed with depth of 30 cm from the wall. After statistical analysis it was found that: the thermal profile of the furnace surface and at different heights was heterogeneous; and the ranges of density and moisture content of wood are within recommended for use as an energy source standards. We conclude that even at low temperatures reached during firing there was a significant production of good quality products, this is due to high concentrations of iron oxide and potassium oxide found in clay, which lowers the melting point of the piece. The average burn time for each step varied 650-2100 minutes wood consumption was on average 20 m3, product quality was on average 16% of first quality, 70% second, third and 5% to 10% loss . The distance between the wire and the surface of the oven was a significant parameter for all treatments, but with different variations, meaning that the wire should not be so generic and unique form, used as a criterion for completion of the burn process. The central part of the furnace was the area that reached higher temperature, and in a unified manner, with the highest concentration of top quality products. The ideal temperature curve, which provided the highest quality of ceramic products was achieved in the central part of the furnace
Resumo:
Remote Communities. Absence of artifacts and minimization of the exacerbated consumption of modernity. The desire which spread beyond what reality can provide. Expressions like this are present in this paper which focus in the social representations of school built by residents who live at the riversides of Môa and Azul Rivers, in Mâncio Lima, Acre State. To do so, we used the methodological contribution of the semi-structured interview, observation of the place while a natural inhabitant of the region, and also photos analyses of local reality. A key feature of the riverside homes is the glued paper on the walls of houses forming a panel set of portraits, pictures, letters and numbers for all appreciated. Regardless of whether or not read, there is admiration for the color of the images, the layout of the letters, and the things of the city awakening the desire to obtain school knowledge. The resident of this Amazon region maintains a close relationship between thinking, acting and feeling living harmonically with nature that connects them to the ideal landscape which is revisited by the graphic material that attracts wondering what exists beyond the shores of the river, beyond the horizon of green forests. It is a life entirely accomplished by the imaginary where exist a framed landscape merged and confused by the real and the supernatural, in which men and gods walk together by the forest, sailing by the rivers and seek a possible aesthetic between the real and ideal. The Theory of Social Representations spread by Serge Moscovici (2005) and Jodelet (2001) guided our gaze on the understanding what the school is and its representation to the riversides, as well to reveal the relation they practice with the knowledge that is spread by the mystification and the knowledge that is practice daily. Based in Bardin s thematic analysis (2004) we tried to raise such contents combining them in five analysis categories
Resumo:
In order to obtain a biofuel similar to mineral diesel, lanthanum-incorporated SBA- 15 nanostructured materials, LaSBA-15(pH), with different Si/La molar ratios (75, 50, 25), were synthesized in a two-steps hydrothermal procedure, with pH-adjusting of the synthesis gel at 6, and were used like catalytic solids in the buriti oil thermal catalytic cracking. These solids were characterized by X-ray fluorescence (XRF), powder X-ray diffraction (XRD), thermogravimetric analysis (TG/DTG), infrared spectroscopy (FTIR), nitrogen porosimetry and ethanol dehydration, aiming to active sites identify. Taken together, the analyses indicated that the synthesis method has employed to obtain materials highly ordered mesostructures with large average pore sizes and high surface area, besides suggested that the lanthanum was incorporated in the SBA-15 both into the framework as well as within the mesopores. Catalytic dehydration of ethanol over the LaSBA-15(pH) products has shown that they have weak Lewis acid and basic functionalities, indicative of the presence of lanthanum oxide in these samples, especially on the La75SBA-15(pH) sample, which has presented the highest selectivity to ethylene. The buriti oil thermal and thermal catalytic cracking, realized from the room temperature to 450 ºC in a simple distillation system, has allowed obtaining two liquid fractions, each consisting of two phases, one aqueous and another organic, organic liquid (OL). The OL obtained from first fractions has shown high acid index, even in the thermal catalytic process. One the other hand, OL coming from second ones, called green diesel (GD), have presented low acid index, particularly that one obtained from the thermal catalytic process realized over LaSBA-15(pH) samples. The acid sites presence in these samples, associated to their large average pore sizes and high surface areas, have allowed them, especially the La75SBA-15(pH), to present deoxygenating activity in the buriti oil thermal catalytic cracking, providing an oxygenates content reduction, particularly carboxylic acids, in the GD. Furthermore, the GD comes from the second liquid fraction obtained in the buriti oil thermal catalytic cracking over this latest solid sample has shown hydrocarbons composition and physic-chemical properties similar to that mineral diesel, beyond sulfur content low
Resumo:
In this work were synthesized and characterized the materials mesoporous SBA-15 and Al- SBA-15, Si / Al = 25, 50 and 75, discovered by researchers at the University of California- Santa Barbara, USA, with pore diameters ranging from 2 to 30 nm and wall thickness from 3.1 to 6.4 nm, making these promising materials in the field of catalysis, particularly for petroleum refining (catalytic cracking), as their mesopores facilitate access of the molecules constituting the oil to active sites, thereby increasing the production of hydrocarbons in the range of light and medium. To verify that the materials used as catalysts were successfully synthesized, they were characterized using techniques of X-ray diffraction (XRD), absorption spectroscopy in the infrared Fourier transform (FT-IR) and adsorption nitrogen (BET). Aiming to check the catalytic activity thereof, a sample of atmospheric residue oil (ATR) from the pole Guamaré-RN was performed the process by means of thermogravimetry and thermal degradation of catalytic residue. Upon the curves, it was observed a reduction in the onset temperature of the decomposition process of catalytic ATR. For the kinetic model proposed by Flynn-Wall yielded some parameters to determine the apparent activation energy of decomposition, being shown the efficiency of mesoporous materials, since there was a decrease in the activation energy for the reactions using catalysts. The ATR was also subjected to pyrolysis process using a pyrolyzer with gas chromatography coupled to a mass spectrometer. Through the chromatograms obtained, there was an increase in the yield of the compounds in the range of gasoline and diesel from the catalytic pyrolysis, with emphasis on Al-SBA-15 (Si / Al = 25), which showed a percentage higher than the other catalysts. These results are due to the fact that the synthesized materials exhibit specific properties for application in the process of pyrolysis of complex molecules and high molecular weight as constituents of the ATR
Resumo:
We report a theoretical investigation of the magnetic phases and hysteresis of exchange biased ferromagnetic (F) nanoelements for three di erent systems: exchange biased nanoparticles, exchange biased narrow ferromagnetic stripes and exchange biased thin ferromagnetic lms. In all cases the focus is on the new e ects produced by suitable patterns of the exchange energy coupling the ferromagnetic nanoelement with a large anisotropy antiferromagnetic (AF) substrate. We investigate the hysteresis of iron and permalloy nanoparticles with a square basis, with lateral dimensions between 45 nm and 120 nm and thickness between 12 nm and 21 nm. Interface bias is aimed at producing large domains in thin lms. Our results show that, contrary to intuition, the interface exchange coupling may generate vortex states along the hysteresis loop. Also, the threshold value of the interface eld strength for vortex nucleation is smaller for iron nanoelements. We investigate the nucleation and depinning of an array of domain walls pinned at interface defects of a vicinal stripe/AF bilayer. The interface exchange eld displays a periodic pattern corresponding to the topology of the AF vicinal substrate. The vicinal AF substrate consists of a sequence of terraces, each with spins from one AF subalattice, alternating one another. As a result the interface eld of neighboring terraces point in opposite direction, leading to the nucleation of a sequence of domain walls in the ferromagnetic stripe. We investigated iron an permalloy micrometric stripes, with width ranging from 100 nm and 300 nm and thickness of 5 nm. We focused in domain wall sequences with same chirality and alternate chirality. We have found that for 100nm terraces the same chiraility sequence is more stable, requiring a larger value of the external eld for depinning. The third system consists of an iron lm with a thickness of 5 nm, exchange coupled to an AF substrate with a periodic distribution of islands where the AF spins have the opposite direction of the spins in the background. This corresponds to a two-sublattice noncompensated AF plane (such as the surface of a (100) FeF2 lm), with monolayer-height islands containing spins of one sublattice on a surface containing spins of the opposite sublattice. The interface eld acting in the ferromagnetic spins over the islands points in the opposite direction of that in the spins over the background. This a model system for the investigation of interface roughness e ects. We have studied the coercicivity an exchange bias hysteresis shift as a function of the distance between the islands and the degree of interface roughness. We have found a relevant reduction of coercivity for nearly compensated interfaces. Also the e ective hysteresis shift is not proportional to the liquid moment of the AF plane. We also developed an analytical model which reproduces qualitatively the results of numerical simulations
Resumo:
Pós-graduação em Odontologia - FOAR
Resumo:
Esta dissertação de mestrado apresenta o projeto e a construção de um robô móvel terrestre denominado LOGBOT, com tração de movimento do tipo diferencial – com duas rodas motoras e uma roda livre para manter a estabilidade de sua estrutura em relação à superfície. O controle do robô dispõe dos modos de telemetria e autônomo. No modo de controle por telemetria (ROV), a comunicação do robô com a estação de controle é feita por radiofreqüência a uma distância de até um quilometro em ambientes externos, e até cem metros em ambientes internos. No modo de controle autônomo (AGV), o robô tem habilidade para navegar em ambientes internos e desconhecidos usando sempre a parede à sua esquerda como referência para a trajetória de seu movimento. A seqüência de movimentos para execução da trajetória é enviada para a estação de controle que realiza análises de desempenho do robô. Para executar suas tarefas no modo autônomo, a programação do robô conta com um agente inteligente reativo, que detecta características do ambiente (obstáculos, final de paredes, etc.) e decide sobre qual atitude deve ser executada pelo robô, com objetivo de contornar os obstáculos e controlar a velocidade de suas rodas. Os problemas de erro odométrico e suas correções com base no uso de informações sensoriais externas são devidamente tratados. Técnicas de controle hierárquico do robô como um todo e controle em malha fechada da velocidade das rodas do robô são usadas. Os resultados mostraram que o robô móvel LOGBOT é capaz de navegar, com estabilidade e precisão, em ambientes internos no formato de um corredor (wall following).
Resumo:
This work presents a fast, easy, standardized and planned method to build family homes in order to collaborate with the decline of housing deficit and, at the same time, meet families who wish to invest in building their own houses, once that our country is experiencing an economical prosperity . This method has been widely used nowadays because it is being deployed in large-scale and in a standardized pattern, reducing decreasing significantly the construction time. The concrete wall, shaped in loco depends on unique processes. For this reason, a well trained staff is required so the constructive process can be executed in a fast pace, showing better results than other construction methods. This project will address all the materials used to build the molded concrete walls in loco, their sequence assembly, application, types, characteristics and performances. At the end, a way used by building companies of locating the concrete will also be given. Although there is no specific Brazilian norm for this type of construction, a study on this topic will soon be released. Therefore, the studies for the execution of this project were based on Brazilian standards prevailing at the time, construction magazines and books that are based on building methods considered more common