980 resultados para PROPORTIONAL COUNTERS
Resumo:
The variation of gas amplification with applied voltage is an important characteristic of a proportional counter. Results of studies on gas amplification for gas fillings of argon quenched with ethane and carbon dioxide are given. The effects of (a) pressure, (b) quenching agent and (c) concentration on A are discussed briefly.
Resumo:
"LADC 148"
Resumo:
Radioactivity induced by a 15-MeV proton beam extracted into air was studied at the beam transport line of the 18-MeV cyclotron at the Bern University Hospital (Inselspital). The produced radioactivity was calculated and measured by means of proportional counters located at the main exhaust of the laboratory. These devices were designed for precise assessment of air contamination for radiation protection purposes. The main produced isotopes were 11C, 13N and 14O. Both measurements and calculations correspond to two different irradiation conditions. In the former, protons were allowed to travel for their full range in air. In the latter, they were stopped at the distance of 1.5 m by a beam dump. Radioactivity was measured continuously in the exhausted air starting from 2 min after the end of irradiation. For this reason, the short-lived 14O isotope gave a negligible contribution to the measured activity. Good agreement was found between the measurements and the calculations within the estimated uncertainties. Currents in the range of 120–370 nA were extracted in air for 10–30 s producing activities of 9–22 MBq of 11C and 13N. The total activities for 11C and 13N per beam current and irradiation time for the former and the latter irradiation conditions were measured to be (3.60 ± 0.48) × 10−3 MBq (nA s)−1 and (2.89 ± 0.37) × 10−3 MBq (nA s)−1, respectively.
Resumo:
La fusión nuclear es, hoy en día, una alternativa energética a la que la comunidad internacional dedica mucho esfuerzo. El objetivo es el de generar entre diez y cincuenta veces más energía que la que consume mediante reacciones de fusión que se producirán en una mezcla de deuterio (D) y tritio (T) en forma de plasma a doscientos millones de grados centígrados. En los futuros reactores nucleares de fusión será necesario producir el tritio utilizado como combustible en el propio reactor termonuclear. Este hecho supone dar un paso más que las actuales máquinas experimentales dedicadas fundamentalmente al estudio de la física del plasma. Así pues, el tritio, en un reactor de fusión, se produce en sus envolturas regeneradoras cuya misión fundamental es la de blindaje neutrónico, producir y recuperar tritio (fuel para la reacción DT del plasma) y por último convertir la energía de los neutrones en calor. Existen diferentes conceptos de envolturas que pueden ser sólidas o líquidas. Las primeras se basan en cerámicas de litio (Li2O, Li4SiO4, Li2TiO3, Li2ZrO3) y multiplicadores neutrónicos de Be, necesarios para conseguir la cantidad adecuada de tritio. Los segundos se basan en el uso de metales líquidos o sales fundidas (Li, LiPb, FLIBE, FLINABE) con multiplicadores neutrónicos de Be o el propio Pb en el caso de LiPb. Los materiales estructurales pasan por aceros ferrítico-martensíticos de baja activación, aleaciones de vanadio o incluso SiCf/SiC. Cada uno de los diferentes conceptos de envoltura tendrá una problemática asociada que se estudiará en el reactor experimental ITER (del inglés, “International Thermonuclear Experimental Reactor”). Sin embargo, ITER no puede responder las cuestiones asociadas al daño de materiales y el efecto de la radiación neutrónica en las diferentes funciones de las envolturas regeneradoras. Como referencia, la primera pared de un reactor de fusión de 4000MW recibiría 30 dpa/año (valores para Fe-56) mientras que en ITER se conseguirían <10 dpa en toda su vida útil. Esta tesis se encuadra en el acuerdo bilateral entre Europa y Japón denominado “Broader Approach Agreement “(BA) (2007-2017) en el cual España juega un papel destacable. Estos proyectos, complementarios con ITER, son el acelerador para pruebas de materiales IFMIF (del inglés, “International Fusion Materials Irradiation Facility”) y el dispositivo de fusión JT-60SA. Así, los efectos de la irradiación de materiales en materiales candidatos para reactores de fusión se estudiarán en IFMIF. El objetivo de esta tesis es el diseño de un módulo de IFMIF para irradiación de envolturas regeneradoras basadas en metales líquidos para reactores de fusión. El módulo se llamará LBVM (del inglés, “Liquid Breeder Validation Module”). La propuesta surge de la necesidad de irradiar materiales funcionales para envolturas regeneradoras líquidas para reactores de fusión debido a que el diseño conceptual de IFMIF no contaba con esta utilidad. Con objeto de analizar la viabilidad de la presente propuesta, se han realizado cálculos neutrónicos para evaluar la idoneidad de llevar a cabo experimentos relacionados con envolturas líquidas en IFMIF. Así, se han considerado diferentes candidatos a materiales funcionales de envolturas regeneradoras: Fe (base de los materiales estructurales), SiC (material candidato para los FCI´s (del inglés, “Flow Channel Inserts”) en una envoltura regeneradora líquida, SiO2 (candidato para recubrimientos antipermeación), CaO (candidato para recubrimientos aislantes), Al2O3 (candidato para recubrimientos antipermeación y aislantes) y AlN (material candidato para recubrimientos aislantes). En cada uno de estos materiales se han calculado los parámetros de irradiación más significativos (dpa, H/dpa y He/dpa) en diferentes posiciones de IFMIF. Estos valores se han comparado con los esperados en la primera pared y en la zona regeneradora de tritio de un reactor de fusión. Para ello se ha elegido un reactor tipo HCLL (del inglés, “Helium Cooled Lithium Lead”) por tratarse de uno de los más prometedores. Además, los valores también se han comparado con los que se obtendrían en un reactor rápido de fisión puesto que la mayoría de las irradiaciones actuales se hacen en reactores de este tipo. Como conclusión al análisis de viabilidad, se puede decir que los materiales funcionales para mantos regeneradores líquidos podrían probarse en la zona de medio flujo de IFMIF donde se obtendrían ratios de H/dpa y He/dpa muy parecidos a los esperados en las zonas más irradiadas de un reactor de fusión. Además, con el objetivo de ajustar todavía más los valores, se propone el uso de un moderador de W (a considerar en algunas campañas de irradiación solamente debido a que su uso hace que los valores de dpa totales disminuyan). Los valores obtenidos para un reactor de fisión refuerzan la idea de la necesidad del LBVM, ya que los valores obtenidos de H/dpa y He/dpa son muy inferiores a los esperados en fusión y, por lo tanto, no representativos. Una vez demostrada la idoneidad de IFMIF para irradiar envolturas regeneradoras líquidas, y del estudio de la problemática asociada a las envolturas líquidas, también incluida en esta tesis, se proponen tres tipos de experimentos diferentes como base de diseño del LBVM. Éstos se orientan en las necesidades de un reactor tipo HCLL aunque a lo largo de la tesis se discute la aplicabilidad para otros reactores e incluso se proponen experimentos adicionales. Así, la capacidad experimental del módulo estaría centrada en el estudio del comportamiento de litio plomo, permeación de tritio, corrosión y compatibilidad de materiales. Para cada uno de los experimentos se propone un esquema experimental, se definen las condiciones necesarias en el módulo y la instrumentación requerida para controlar y diagnosticar las cápsulas experimentales. Para llevar a cabo los experimentos propuestos se propone el LBVM, ubicado en la zona de medio flujo de IFMIF, en su celda caliente, y con capacidad para 16 cápsulas experimentales. Cada cápsula (24-22 mm de diámetro y 80 mm de altura) contendrá la aleación eutéctica LiPb (hasta 50 mm de la altura de la cápsula) en contacto con diferentes muestras de materiales. Ésta irá soportada en el interior de tubos de acero por los que circulará un gas de purga (He), necesario para arrastrar el tritio generado en el eutéctico y permeado a través de las paredes de las cápsulas (continuamente, durante irradiación). Estos tubos, a su vez, se instalarán en una carcasa también de acero que proporcionará soporte y refrigeración tanto a los tubos como a sus cápsulas experimentales interiores. El módulo, en su conjunto, permitirá la extracción de las señales experimentales y el gas de purga. Así, a través de la estación de medida de tritio y el sistema de control, se obtendrán los datos experimentales para su análisis y extracción de conclusiones experimentales. Además del análisis de datos experimentales, algunas de estas señales tendrán una función de seguridad y por tanto jugarán un papel primordial en la operación del módulo. Para el correcto funcionamiento de las cápsulas y poder controlar su temperatura, cada cápsula se equipará con un calentador eléctrico y por tanto el módulo requerirá también ser conectado a la alimentación eléctrica. El diseño del módulo y su lógica de operación se describe en detalle en esta tesis. La justificación técnica de cada una de las partes que componen el módulo se ha realizado con soporte de cálculos de transporte de tritio, termohidráulicos y mecánicos. Una de las principales conclusiones de los cálculos de transporte de tritio es que es perfectamente viable medir el tritio permeado en las cápsulas mediante cámaras de ionización y contadores proporcionales comerciales, con sensibilidades en el orden de 10-9 Bq/m3. Los resultados son aplicables a todos los experimentos, incluso si son cápsulas a bajas temperaturas o si llevan recubrimientos antipermeación. Desde un punto de vista de seguridad, el conocimiento de la cantidad de tritio que está siendo transportada con el gas de purga puede ser usado para detectar de ciertos problemas que puedan estar sucediendo en el módulo como por ejemplo, la rotura de una cápsula. Además, es necesario conocer el balance de tritio de la instalación. Las pérdidas esperadas el refrigerante y la celda caliente de IFMIF se pueden considerar despreciables para condiciones normales de funcionamiento. Los cálculos termohidráulicos se han realizado con el objetivo de optimizar el diseño de las cápsulas experimentales y el LBVM de manera que se pueda cumplir el principal requisito del módulo que es llevar a cabo los experimentos a temperaturas comprendidas entre 300-550ºC. Para ello, se ha dimensionado la refrigeración necesaria del módulo y evaluado la geometría de las cápsulas, tubos experimentales y la zona experimental del contenedor. Como consecuencia de los análisis realizados, se han elegido cápsulas y tubos cilíndricos instalados en compartimentos cilíndricos debido a su buen comportamiento mecánico (las tensiones debidas a la presión de los fluidos se ven reducidas significativamente con una geometría cilíndrica en lugar de prismática) y térmico (uniformidad de temperatura en las paredes de los tubos y cápsulas). Se han obtenido campos de presión, temperatura y velocidad en diferentes zonas críticas del módulo concluyendo que la presente propuesta es factible. Cabe destacar que el uso de códigos fluidodinámicos (e.g. ANSYS-CFX, utilizado en esta tesis) para el diseño de cápsulas experimentales de IFMIF no es directo. La razón de ello es que los modelos de turbulencia tienden a subestimar la temperatura de pared en mini canales de helio sometidos a altos flujos de calor debido al cambio de las propiedades del fluido cerca de la pared. Los diferentes modelos de turbulencia presentes en dicho código han tenido que ser estudiados con detalle y validados con resultados experimentales. El modelo SST (del inglés, “Shear Stress Transport Model”) para turbulencia en transición ha sido identificado como adecuado para simular el comportamiento del helio de refrigeración y la temperatura en las paredes de las cápsulas experimentales. Con la geometría propuesta y los valores principales de refrigeración y purga definidos, se ha analizado el comportamiento mecánico de cada uno de los tubos experimentales que contendrá el módulo. Los resultados de tensiones obtenidos, han sido comparados con los valores máximos recomendados en códigos de diseño estructural como el SDC-IC (del inglés, “Structural Design Criteria for ITER Components”) para así evaluar el grado de protección contra el colapso plástico. La conclusión del estudio muestra que la propuesta es mecánicamente robusta. El LBVM implica el uso de metales líquidos y la generación de tritio además del riesgo asociado a la activación neutrónica. Por ello, se han estudiado los riesgos asociados al uso de metales líquidos y el tritio. Además, se ha incluido una evaluación preliminar de los riesgos radiológicos asociados a la activación de materiales y el calor residual en el módulo después de la irradiación así como un escenario de pérdida de refrigerante. Los riesgos asociados al módulo de naturaleza convencional están asociados al manejo de metales líquidos cuyas reacciones con aire o agua se asocian con emisión de aerosoles y probabilidad de fuego. De entre los riesgos nucleares destacan la generación de gases radiactivos como el tritio u otros radioisótopos volátiles como el Po-210. No se espera que el módulo suponga un impacto medioambiental asociado a posibles escapes. Sin embargo, es necesario un manejo adecuado tanto de las cápsulas experimentales como del módulo contenedor así como de las líneas de purga durante operación. Después de un día de después de la parada, tras un año de irradiación, tendremos una dosis de contacto de 7000 Sv/h en la zona experimental del contenedor, 2300 Sv/h en la cápsula y 25 Sv/h en el LiPb. El uso por lo tanto de manipulación remota está previsto para el manejo del módulo irradiado. Por último, en esta tesis se ha estudiado también las posibilidades existentes para la fabricación del módulo. De entre las técnicas propuestas, destacan la electroerosión, soldaduras por haz de electrones o por soldadura láser. Las bases para el diseño final del LBVM han sido pues establecidas en el marco de este trabajo y han sido incluidas en el diseño intermedio de IFMIF, que será desarrollado en el futuro, como parte del diseño final de la instalación IFMIF. ABSTRACT Nuclear fusion is, today, an alternative energy source to which the international community devotes a great effort. The goal is to generate 10 to 50 times more energy than the input power by means of fusion reactions that occur in deuterium (D) and tritium (T) plasma at two hundred million degrees Celsius. In the future commercial reactors it will be necessary to breed the tritium used as fuel in situ, by the reactor itself. This constitutes a step further from current experimental machines dedicated mainly to the study of the plasma physics. Therefore, tritium, in fusion reactors, will be produced in the so-called breeder blankets whose primary mission is to provide neutron shielding, produce and recover tritium and convert the neutron energy into heat. There are different concepts of breeding blankets that can be separated into two main categories: solids or liquids. The former are based on ceramics containing lithium as Li2O , Li4SiO4 , Li2TiO3 , Li2ZrO3 and Be, used as a neutron multiplier, required to achieve the required amount of tritium. The liquid concepts are based on molten salts or liquid metals as pure Li, LiPb, FLIBE or FLINABE. These blankets use, as neutron multipliers, Be or Pb (in the case of the concepts based on LiPb). Proposed structural materials comprise various options, always with low activation characteristics, as low activation ferritic-martensitic steels, vanadium alloys or even SiCf/SiC. Each concept of breeding blanket has specific challenges that will be studied in the experimental reactor ITER (International Thermonuclear Experimental Reactor). However, ITER cannot answer questions associated to material damage and the effect of neutron radiation in the different breeding blankets functions and performance. As a reference, the first wall of a fusion reactor of 4000 MW will receive about 30 dpa / year (values for Fe-56) , while values expected in ITER would be <10 dpa in its entire lifetime. Consequently, the irradiation effects on candidate materials for fusion reactors will be studied in IFMIF (International Fusion Material Irradiation Facility). This thesis fits in the framework of the bilateral agreement among Europe and Japan which is called “Broader Approach Agreement “(BA) (2007-2017) where Spain plays a key role. These projects, complementary to ITER, are mainly IFMIF and the fusion facility JT-60SA. The purpose of this thesis is the design of an irradiation module to test candidate materials for breeding blankets in IFMIF, the so-called Liquid Breeder Validation Module (LBVM). This proposal is born from the fact that this option was not considered in the conceptual design of the facility. As a first step, in order to study the feasibility of this proposal, neutronic calculations have been performed to estimate irradiation parameters in different materials foreseen for liquid breeding blankets. Various functional materials were considered: Fe (base of structural materials), SiC (candidate material for flow channel inserts, SiO2 (candidate for antipermeation coatings), CaO (candidate for insulating coatings), Al2O3 (candidate for antipermeation and insulating coatings) and AlN (candidate for insulation coating material). For each material, the most significant irradiation parameters have been calculated (dpa, H/dpa and He/dpa) in different positions of IFMIF. These values were compared to those expected in the first wall and breeding zone of a fusion reactor. For this exercise, a HCLL (Helium Cooled Lithium Lead) type was selected as it is one of the most promising options. In addition, estimated values were also compared with those obtained in a fast fission reactor since most of existing irradiations have been made in these installations. The main conclusion of this study is that the medium flux area of IFMIF offers a good irradiation environment to irradiate functional materials for liquid breeding blankets. The obtained ratios of H/dpa and He/dpa are very similar to those expected in the most irradiated areas of a fusion reactor. Moreover, with the aim of bringing the values further close, the use of a W moderator is proposed to be used only in some experimental campaigns (as obviously, the total amount of dpa decreases). The values of ratios obtained for a fission reactor, much lower than in a fusion reactor, reinforce the need of LBVM for IFMIF. Having demonstrated the suitability of IFMIF to irradiate functional materials for liquid breeding blankets, and an analysis of the main problems associated to each type of liquid breeding blanket, also presented in this thesis, three different experiments are proposed as basis for the design of the LBVM. These experiments are dedicated to the needs of a blanket HCLL type although the applicability of the module for other blankets is also discussed. Therefore, the experimental capability of the module is focused on the study of the behavior of the eutectic alloy LiPb, tritium permeation, corrosion and material compatibility. For each of the experiments proposed an experimental scheme is given explaining the different module conditions and defining the required instrumentation to control and monitor the experimental capsules. In order to carry out the proposed experiments, the LBVM is proposed, located in the medium flux area of the IFMIF hot cell, with capability of up to 16 experimental capsules. Each capsule (24-22 mm of diameter, 80 mm high) will contain the eutectic allow LiPb (up to 50 mm of capsule high) in contact with different material specimens. They will be supported inside rigs or steel pipes. Helium will be used as purge gas, to sweep the tritium generated in the eutectic and permeated through the capsule walls (continuously, during irradiation). These tubes, will be installed in a steel container providing support and cooling for the tubes and hence the inner experimental capsules. The experimental data will consist of on line monitoring signals and the analysis of purge gas by the tritium measurement station. In addition to the experimental signals, the module will produce signals having a safety function and therefore playing a major role in the operation of the module. For an adequate operation of the capsules and to control its temperature, each capsule will be equipped with an electrical heater so the module will to be connected to an electrical power supply. The technical justification behind the dimensioning of each of these parts forming the module is presented supported by tritium transport calculations, thermalhydraulic and structural analysis. One of the main conclusions of the tritium transport calculations is that the measure of the permeated tritium is perfectly achievable by commercial ionization chambers and proportional counters with sensitivity of 10-9 Bq/m3. The results are applicable to all experiments, even to low temperature capsules or to the ones using antipermeation coatings. From a safety point of view, the knowledge of the amount of tritium being swept by the purge gas is a clear indicator of certain problems that may be occurring in the module such a capsule rupture. In addition, the tritium balance in the installation should be known. Losses of purge gas permeated into the refrigerant and the hot cell itself through the container have been assessed concluding that they are negligible for normal operation. Thermal hydraulic calculations were performed in order to optimize the design of experimental capsules and LBVM to fulfill one of the main requirements of the module: to perform experiments at uniform temperatures between 300-550ºC. The necessary cooling of the module and the geometry of the capsules, rigs and testing area of the container were dimensioned. As a result of the analyses, cylindrical capsules and rigs in cylindrical compartments were selected because of their good mechanical behavior (stresses due to fluid pressure are reduced significantly with a cylindrical shape rather than prismatic) and thermal (temperature uniformity in the walls of the tubes and capsules). Fields of pressure, temperature and velocity in different critical areas of the module were obtained concluding that the proposal is feasible. It is important to mention that the use of fluid dynamic codes as ANSYS-CFX (used in this thesis) for designing experimental capsules for IFMIF is not direct. The reason for this is that, under strongly heated helium mini channels, turbulence models tend to underestimate the wall temperature because of the change of helium properties near the wall. Therefore, the different code turbulence models had to be studied in detail and validated against experimental results. ANSYS-CFX SST (Shear Stress Transport Model) for transitional turbulence model has been identified among many others as the suitable one for modeling the cooling helium and the temperature on the walls of experimental capsules. Once the geometry and the main purge and cooling parameters have been defined, the mechanical behavior of each experimental tube or rig including capsules is analyzed. Resulting stresses are compared with the maximum values recommended by applicable structural design codes such as the SDC- IC (Structural Design Criteria for ITER Components) in order to assess the degree of protection against plastic collapse. The conclusion shows that the proposal is mechanically robust. The LBVM involves the use of liquid metals, tritium and the risk associated with neutron activation. The risks related with the handling of liquid metals and tritium are studied in this thesis. In addition, the radiological risks associated with the activation of materials in the module and the residual heat after irradiation are evaluated, including a scenario of loss of coolant. Among the identified conventional risks associated with the module highlights the handling of liquid metals which reactions with water or air are accompanied by the emission of aerosols and fire probability. Regarding the nuclear risks, the generation of radioactive gases such as tritium or volatile radioisotopes such as Po-210 is the main hazard to be considered. An environmental impact associated to possible releases is not expected. Nevertheless, an appropriate handling of capsules, experimental tubes, and container including purge lines is required. After one day after shutdown and one year of irradiation, the experimental area of the module will present a contact dose rate of about 7000 Sv/h, 2300 Sv/h in the experimental capsules and 25 Sv/h in the LiPb. Therefore, the use of remote handling is envisaged for the irradiated module. Finally, the different possibilities for the module manufacturing have been studied. Among the proposed techniques highlights the electro discharge machining, brazing, electron beam welding or laser welding. The bases for the final design of the LBVM have been included in the framework of the this work and included in the intermediate design report of IFMIF which will be developed in future, as part of the IFMIF facility final design.
Resumo:
Dissertacao (Mestrado)
Resumo:
Computer resource allocation represents a significant challenge particularly for multiprocessor systems, which consist of shared computing resources to be allocated among co-runner processes and threads. While an efficient resource allocation would result in a highly efficient and stable overall multiprocessor system and individual thread performance, ineffective poor resource allocation causes significant performance bottlenecks even for the system with high computing resources. This thesis proposes a cache aware adaptive closed loop scheduling framework as an efficient resource allocation strategy for the highly dynamic resource management problem, which requires instant estimation of highly uncertain and unpredictable resource patterns. Many different approaches to this highly dynamic resource allocation problem have been developed but neither the dynamic nature nor the time-varying and uncertain characteristics of the resource allocation problem is well considered. These approaches facilitate either static and dynamic optimization methods or advanced scheduling algorithms such as the Proportional Fair (PFair) scheduling algorithm. Some of these approaches, which consider the dynamic nature of multiprocessor systems, apply only a basic closed loop system; hence, they fail to take the time-varying and uncertainty of the system into account. Therefore, further research into the multiprocessor resource allocation is required. Our closed loop cache aware adaptive scheduling framework takes the resource availability and the resource usage patterns into account by measuring time-varying factors such as cache miss counts, stalls and instruction counts. More specifically, the cache usage pattern of the thread is identified using QR recursive least square algorithm (RLS) and cache miss count time series statistics. For the identified cache resource dynamics, our closed loop cache aware adaptive scheduling framework enforces instruction fairness for the threads. Fairness in the context of our research project is defined as a resource allocation equity, which reduces corunner thread dependence in a shared resource environment. In this way, instruction count degradation due to shared cache resource conflicts is overcome. In this respect, our closed loop cache aware adaptive scheduling framework contributes to the research field in two major and three minor aspects. The two major contributions lead to the cache aware scheduling system. The first major contribution is the development of the execution fairness algorithm, which degrades the co-runner cache impact on the thread performance. The second contribution is the development of relevant mathematical models, such as thread execution pattern and cache access pattern models, which in fact formulate the execution fairness algorithm in terms of mathematical quantities. Following the development of the cache aware scheduling system, our adaptive self-tuning control framework is constructed to add an adaptive closed loop aspect to the cache aware scheduling system. This control framework in fact consists of two main components: the parameter estimator, and the controller design module. The first minor contribution is the development of the parameter estimators; the QR Recursive Least Square(RLS) algorithm is applied into our closed loop cache aware adaptive scheduling framework to estimate highly uncertain and time-varying cache resource patterns of threads. The second minor contribution is the designing of a controller design module; the algebraic controller design algorithm, Pole Placement, is utilized to design the relevant controller, which is able to provide desired timevarying control action. The adaptive self-tuning control framework and cache aware scheduling system in fact constitute our final framework, closed loop cache aware adaptive scheduling framework. The third minor contribution is to validate this cache aware adaptive closed loop scheduling framework efficiency in overwhelming the co-runner cache dependency. The timeseries statistical counters are developed for M-Sim Multi-Core Simulator; and the theoretical findings and mathematical formulations are applied as MATLAB m-file software codes. In this way, the overall framework is tested and experiment outcomes are analyzed. According to our experiment outcomes, it is concluded that our closed loop cache aware adaptive scheduling framework successfully drives co-runner cache dependent thread instruction count to co-runner independent instruction count with an error margin up to 25% in case cache is highly utilized. In addition, thread cache access pattern is also estimated with 75% accuracy.
Resumo:
An alternative approach to digital PWM generation using an adder rather than a counter is presented. This offers several advantages. The resolution and gain of the pulse width modulator remain constant regardless of the module clock frequency and PWM output frequency. The PWM resolution also becomes fixed at the register width. Even at high PWM frequencies, the resolution remains high when averaged over a number of PWM cycles. An inherent dithering of the PWM waveform introduced over successive cycles blurs the switching spectra without distorting the modulating waveform. The technique also lends itself to easily generating several phase shifted PWM waveforms suitable for multilevel converter modulation.
Resumo:
Cum ./LSTA_A_8828879_O_XML_IMAGES/LSTA_A_8828879_O_ILM0001.gif rule [Singh (1975)] has been suggested in the literature for finding approximately optimum strata boundaries for proportional allocation, when the stratification is done on the study variable. This paper shows that for the class of density functions arising from the Wang and Aggarwal (1984) representation of the Lorenz Curve (or DBV curves in case of inventory theory), the cum ./LSTA_A_8828879_O_XML_IMAGES/LSTA_A_8828879_O_ILM0002.gif rule in place of giving approximately optimum strata boundaries, yields exactly optimum boundaries. It is also shown that the conjecture of Mahalanobis (1952) “. . .an optimum or nearly optimum solutions will be obtained when the expected contribution of each stratum to the total aggregate value of Y is made equal for all strata” yields exactly optimum strata boundaries for the case considered in the paper.
Resumo:
Approximate closed-form solutions of the non-linear relative equations of motion of an interceptor pursuing a target under the realistic true proportional navigation (RTPN) guidance law are derived using the Adomian decomposition method in this article. In the literature, no study has been reported on derivation of explicit time-series solutions in closed form of the nonlinear dynamic engagement equations under the RTPN guidance. The Adomian method provides an analytical approximation, requiring no linearization or direct integration of the non-linear terms. The complete derivation of the Adomian polynomials for the analysis of the dynamics of engagement under RTPN guidance is presented for deterministic ideal case, and non-ideal dynamics in the loop that comprises autopilot and actuator dynamics and target manoeuvre, as well as, for a stochastic case. Numerical results illustrate the applicability of the method.
Resumo:
A theorem termed the Geometrical Continuity Theorem is enunciated and proven. This theorem throws light on the aspects of the continuity of the proportional portion with the base weir portion. These two portions constitute the profile of a proportional weir. A weir of this type with circular bottom is designed. The theorem is used to establish the continuity at the junction of the proportional and the base weir portions of this weir. The coordinates of the weir profile are obtained by numerical methods and are furnished in tabular form for ready use by designers. The discharge passing through the weir is a linear function of the head. The verification of the assumed linear discharge-head relation is furnished for one of the three weirs with which experiments were conducted. The coefficient of discharge for this typical weir is found to be a constant with a value of 0.59.
Resumo:
Of the many factors that govern the settling phenomenon, the flow velocity in the settling tanks can be controlled favorably by fixing suitably designed weirs at the outlets of the tanks. The velocity at the bottom should not dislodge the particles that have already settled. These requirements might be met with by velocities which are controlled to be constant with respect to the depth of flow, or velocities which reduce linearly with increasing depth or velocities that vary inversely with the depth. To achieve these types of velocity control, new proportional weirs have been designed. Very near to the outlet of the tank, over a small length, the flow was found to be turbulent and noncompliant with the expected type of velocity control. This small length of the disturbance may be provided over and above the theoretical settling length of the tank, for efficient sedimentation.
Resumo:
Seven different shaped modified proportional V-notches were designed and pertinent data for their use are given in tables 1 - 4. It is shown that the indication accuracies of these weirs are more than that of the conventional V-notch. For five of the designed weirs the indication accuracies are more than that of the conventional rectangular weir at lower heads of flow. All these proportional weirs, except the parabolic based weir, have added advantages over the V-notch in regard to fixing and finding the crest level. Experiments with five weirs (four symmetrical and one unsymmetrical) having rectangular bases and one (symmetrical) with a parabolic base show very good agreement with the theory and give consistent values for the coefficient of discharge, Cd, varying between 0.588 and 0.605, within the ranges of the experiments.