Multi-wall carbon nanotube coating of fluorine-doped tin oxide as an electrode surface modifier for polymer solar cells

A controlled layer of multi-wall carbon nanotubes (MWCNT) was grown directly on top of fluorine-doped tin oxide (FTO) glass electrodes as a surface modifier for improving the performance of polymer solar cells. By using low-temperature chemical vapor deposition with short synthesis times, very short MWCNTs were grown, these uniformly decorating the FTO surface. The chemical vapor deposition parameters were carefully refined to balance the tube size and density, while minimizing the decrease in conductivity and light harvesting of the electrode. As created FTO/CNT electrodes were applied to bulk-heterojunction polymer solar cells, both in direct and inverted architecture. Thanks to the inclusion of MWCNT and the consequent nano-structuring of the electrode surface, we observe an increase in external quantum efficiency in the wavelength range from 550 to 650 nm. Overall, polymer solar cells realized with these FTO/CNT electrodes attain power conversion efficiency higher than 2%, outclassing reference cells based on standard FTO electrodes.

Polymer solar cells: design of materials by donor-acceptor approach

A brief overview of our group research activities is given and the concept of donor acceptor is described for the development of conjugated polymers for optoelectronic devices. In particular, a new family of conjugated polymers based on dithienopyrrole has been synthesized to demonstrate the concept of donor-acceptor. The dithienopyrrole was coupled to benzodithiophene via Stille coupling to obtain two low band gap polymers P5a and P5b having -C18H37 and -2-ethylhexyl alkyl chain respectively. Both the polymers exhibit absorption within the solar spectrum with an optical band gap below 2 eV. Atomic force microscopy revealed that both the polymers form smooth film with roughness of 2.4 nm and photoluminescence measurement of polymer/fullerene derivative blend film suggests effective dissociation of exciton.

Epitaxy-Assisted Creation of PCBM Nanocrystals and Its Application in Constructing Optimized Morphology for Bulk-Heterojunction Polymer Solar Cells

PCBM (a C-60 derivative) is so far the most successful electron acceptor for bulk-heterojunction polymer photovoltaic (PV) cells. Here we present a novel method epitaxy-assisted creation of PCBM nanocrystals and their homogeneous distribution in the matrix using freshly cleaved mica sheet as the substrate. The highly matched epitaxy relationship between the unit cell of PCBM crystal and crystallographic (001) surface of mica induces abundant PCBM nuclei, which subsequently develop into nanoscale crystals with homogeneous dispersion in the composite film.

Novel NIR-absorbing conjugated polymers for efficient polymer solar cells: effect of alkyl chain length on device performance

Three low bandgap conjugated polymers, i.e., PDTPBT-C8, PDTPBT-C6 and PDTPBT-C5, which consist of alternating N-alkyl dithieno[3,2-b: 2',3'-d] pyrrole and 2,1,3-benzothiadiazole units and carry 1-octylnonyl, 1-hexylheptyl and 1-pentylhexyl as side chains, respectively, were synthesized. These polymers show strong absorption in the wavelength range of 600-900 nm with enhanced absorption coefficient as the length of alkyl chain decreases. The film morphology of the polymers and 1-(3-methoxycarbonyl) propyl-1-phenyl-[6,6]-C-61 (PCBM) blends is also dependent on the alkyl chain length. As the length decreases, the film becomes more uniform and the domian size decreases from 400-900 nm for PDTPBT-C8 to similar to 50 nm for PDTPBT-C5.

Toward high-performance polymer solar cells: The importance of morphology control

Polymer solar cells have the potential to become a major electrical power generating tool in the 21st century. R&D endeavors are focusing on continuous roll-to-roll printing of polymeric or organic compounds from solution-like newspapers-to produce flexible and lightweight devices at low cost. It is recognized, though, that besides the functional properties of the compounds the organization of structures on the nanometer level-forced and controlled mainly by the processing conditions applied-determines the performance of state-of-the-art polymer solar cells. In such devices the photoactive layer is composed of at least two functional materials that form nanoscale interpenetrating phases with specific functionalities, a so-called bulk heterojunction. In this perspective article, our current knowledge on the main factors determining the morphology formation and evolution is introduced, and gaps of our understanding on nanoscale structure-property relations in the field of high-performance polymer solar cells are addressed. Finally, promising routes toward formation of tailored morphologies are presented.

Spray pyrolysed In2S3 thin films: A potential electron selective layer for large area inverted bulk-heterojunction polymer solar cells

In this paper, we report the results of investigations on the potential of spray pyrolysis technique in depositing electron selective layer over larger area for the fabrication of inverted bulk-heterojunction polymer solar cells. The electron selective layer (In2S3) was deposited using spray pyrolysis technique and the linear heterojunction device thus fabricated exhibited good uniformity in photovoltaic properties throughout the area of the device. An MEH-PPV:PCBM inverted bulk-heterojunction device with In2S3 electron selective layer (active area of 3.25 3.25 cm2) was also fabricated and tested under indoor and outdoor conditions. Fromthe indoor measurements employing a tungsten halogen lamp (50mW/cm2 illumination), an opencircuit voltage of 0.41V and a short-circuit current of 5.6mA were obtained. On the other hand, the outdoor measurements under direct sunlight (74mW/cm2) yielded an open-circuit voltage of 0.46V and a short-circuit current of 9.37mA

Lead sulfide nanocrystal: conducting polymer solar cells

In this paper, we report photovoltaic devices fabricated from lead sulfide nanocrystals and the conducting polymer poly(2-methoxy-5-(2'-ethyl-hexyloxy)-p-phenylene vinylene). This composite material was produced via a new single-pot synthesis which solves many of the issues associated with existing methods. Our devices have white light power conversion efficiencies under AM 1.5 illumination of 0.7% and single wavelength conversion efficiencies of 1.1%. Additionally, they exhibit remarkably good ideality factors (n = 1.15). Our measurements show that these composites have significant potential as soft optoelectronic materials.

Design of Transparent Conducting Electrodes and Surface Relief Gratings for Plasmonic Polymer Solar Cells

As the concept of renewable energy becomes increasingly important in the modern society, a considerable amount of research has been conducted in the field of organic photovoltaics in recent years. Although organic solar cells generally have had lower efficiencies compared to silicon solar cells, they have the potential to be mass produced via solution processing. A common polymer solar cell architecture relies on the usage of P3HT (electron donor) and PCBM (electron acceptor) bulk heterojunction. One of the main issues with this configuration is that in order to compensate for the high exciton recombination rate, the photoactive layer is often made very thin (on the order of 100 $%). This results in low solar cell photocurrents due to low absorption. This thesis investigates a novel method of light trapping by coupling surface plasmons at the electrode interface via surface relief gratings, leading to EM field enhancements and increased photo absorption. Experimental work was first conducted on developing and optimizing a transparent electrode of the form &'()/+,/&'() to replace the traditional ITO electrode since the azopolymer gratings cannot withstand the high temperature processing of ITO films. It was determined that given the right thickness profiles and deposition conditions, the MAM stack can achieve transmittance and conductivity similar to ITO films. Experimental work was also conducted on the fabrication and characterization of surface relief gratings, as well as verification of the surface plasmon generation. Surface relief gratings were fabricated easily and accurately via laser interference lithography on photosensitive azopolymer films. Laser diffraction studies confirmed the grating pitch, which is dependent on the incident angle and wavelength of the writing beam. AFM experiments were conducted to determine the surface morphology of the gratings, before and after metallic film deposition. It was concluded that metallic film deposition does not significantly alter the grating morphologies.

Design of Transparent Conducting Electrodes and Surface Relief Gratings for Plasmonic Polymer Solar Cells

As the concept of renewable energy becomes increasingly important in the modern society, a considerable amount of research has been conducted in the field of organic photovoltaics in recent years. Although organic solar cells generally have had lower efficiencies compared to silicon solar cells, they have the potential to be mass produced via solution processing. A common polymer solar cell architecture relies on the usage of P3HT (electron donor) and PCBM (electron acceptor) bulk heterojunction. One of the main issues with this configuration is that in order to compensate for the high exciton recombination rate, the photoactive layer is often made very thin (on the order of 100 $%). This results in low solar cell photocurrents due to low absorption. This thesis investigates a novel method of light trapping by coupling surface plasmons at the electrode interface via surface relief gratings, leading to EM field enhancements and increased photo absorption. Experimental work was first conducted on developing and optimizing a transparent electrode of the form &'()/+,/&'() to replace the traditional ITO electrode since the azopolymer gratings cannot withstand the high temperature processing of ITO films. It was determined that given the right thickness profiles and deposition conditions, the MAM stack can achieve transmittance and conductivity similar to ITO films. Experimental work was also conducted on the fabrication and characterization of surface relief gratings, as well as verification of the surface plasmon generation. Surface relief gratings were fabricated easily and accurately via laser interference lithography on photosensitive azopolymer films. Laser diffraction studies confirmed the grating pitch, which is dependent on the incident angle and wavelength of the writing beam. AFM experiments were conducted to determine the surface morphology of the gratings, before and after metallic film deposition. It was concluded that metallic film deposition does not significantly alter the grating morphologies.

Morphology and material stability in polymer solar cells

Polymer solar cells are promising in that they are inexpensive to produce, and due to their mechanical flexibility have the potential for use in applications not possible for more traditional types of solar cells. The performance of polymer solar cells depends strongly on the distribution of electron donor and acceptor material in the active layer. Understanding the connection between morphology and performance as well as how to control the morphology, is therefore of great importance. Furthermore, improving the lifetime of polymer solar cells has become at least as important as improving the efficiency.   In this thesis, the relation between morphology and solar cell performance is studied, and the material stability for blend films of the thiophene-quinoxaline copolymer TQ1 and the fullerene derivatives PCBM and PC70BM. Atomic force microscopy (AFM) and scanning transmission X-ray microscopy (STXM) are used to investigate the lateral morphology, secondary ion mass spectrometry (SIMS) to measure the vertical morphology and near-edge X-ray absorption fine structure (NEXAFS) spectroscopy to determine the surface composition. Lateral phase-separated domains are observed whose size is correlated to the solar cell performance, while the observed TQ1 surface enrichment does not affect the performance. Changes to the unoccupied molecular orbitals as a result of illumination in ambient air are observed by NEXAFS spectroscopy for PCBM, but not for TQ1. The NEXAFS spectrum of PCBM in a blend with TQ1 changes more than that of pristine PCBM. Solar cells in which the active layer has been illuminated in air prior to the deposition of the top electrode exhibit greatly reduced electrical performance. The valence band and absorption spectrum of TQ1 is affected by illumination in air, but the effects are not large enough to account for losses in solar cell performance, which are mainly attributed to PCBM degradation at the active layer surface.

The application of SnS nanoparticles to bulk heterojunction solar cells

Tin mono-sulphide (SnS) nanoparticles were synthesized by a facile method. Reactions producing narrow size distribution SnS nanoparticles with the diameter of 5.0-10 nm were carried out in an ethylene glycol solution at 150 degrees C for 24 h. Bulk heterojunction solar cells with the structure of indium tin oxide (ITO)/polyethylenedioxythiophene polystyrenesulphonate (PEDOT PSS)/SnS polymer/Al were fabricated by blending the nanoparticles with a conjugated polymer to form the active layer for the first time. Current density-voltage characterization of the devices showed that due to the addition of SnS nanoparticles to the polymer film, the device performance can be dramatically improved, compared with that of the pristine polymer solar cells. (c) 2009 Published by Elsevier B.V.

Investigation of P3HT PCBM particle-based solar cells

Die Herstellung von Polymer-Solarzellen aus wässriger Phase stellt eine attraktive Alternative zu der konventionellen lösemittelbasierten Formulierung dar. Die Vorteile der aus wässriger Lösung hergestellten Solarzellen liegen besonders in dem umweltschonenden Herstellungsprozess und in der Möglichkeit, druckbare optoelektronische Bauteile zu generieren. Die Prozessierbarkeit von hydrophoben Halbleitern im wässrigen Milieu wird durch die Dispergierung der Materialien, in Form von Nanopartikeln, erreicht. Der Transfer der Halbleiter in eine Dispersion erfolgt über die Lösemittelverdampfungsmethode. Die Idee der Verwendung von partikelbasierte Solarzellen wurde bereits umgesetzt, allerdings blieben eine genaue Charakterisierung der Partikel sowie ein umfassendes Verständnis des gesamten Fabrikationsvorgangs aus. Deshalb besteht das Ziel dieser Arbeit darin, einen detaillierten Einblick in den Herstellungsprozess von partikelbasierten Solarzellen zu erlangen, mögliche Schwächen aufzudecken, diese zu beseitigen, um so zukünftige Anwendungen zu verbessern. Zur Herstellung von Solarzellen aus wässrigen Dispersionen wurde Poly(3-hexylthiophen-2,5-diyl)/[6,6]-Phenyl-C61-Buttersäure-Methylester (P3HT/PCBM) als Donor/Akzeptor-System verwendet. Die Kernpunkte der Untersuchungen richteten sich zum einen die auf Partikelmorphologie und zum anderen auf die Generierung einer geeigneten Partikelschicht. Beide Parameter haben Auswirkungen auf die Solarzelleneffizienz. Die Morphologie wurde sowohl spektroskopisch über Photolumineszenz-Messungen, als auch visuell mittels Elektronenmikroskopie ermittelt. Auf diese Weise konnte die Partikelmorphologie vollständig aufgeklärt werden, wobei Parallelen zu der Struktur von lösemittelbasierten Solarzellen gefunden wurden. Zudem wurde eine Abhängigkeit der Morphologie von der Präparationstemperatur beobachtet, was eine einfache Steuerung der Partikelstruktur ermöglicht. Im Zuge der Partikelschichtausbildung wurden direkte sowie grenzflächenvermittelnde Beschichtungsmethoden herangezogen. Von diesen Techniken hatte sich aber nur die Rotationsbeschichtung als brauchbare Methode erwiesen, Partikel aus der Dispersion in einen homogenen Film zu überführen. Des Weiteren stand die Aufarbeitung der Partikelschicht durch Ethanol-Waschung und thermische Behandlung im Fokus dieser Arbeit. Beide Maßnahmen wirkten sich positiv auf die Effizienz der Solarzellen aus und trugen entscheidend zu einer Verbesserung der Zellen bei. Insgesamt liefern die gewonnen Erkenntnisse einen detaillierten Überblick über die Herausforderungen, welche bei dem Einsatz von wasserbasierten Dispersionen auftreten. Die Anforderungen partikelbasierter Solarzellen konnten offengelegt werden, dadurch gelang die Herstellung einer Solarzelle mit einer Effizienz von 0.53%. Dieses Ergebnis stellt jedoch noch nicht das Optimum dar und lässt noch Möglichkeiten für Verbesserungen offen.

Water-based nanoparticulate solar cells using a diketopyrrolopyrrole donor polymer

Organic photovoltaic devices with either bulk heterojunction (BHJ) or nanoparticulate (NP) active layers have been prepared from a 1:2 blend of (poly{3,6-dithiophene-2-yl-2,5-di(2-octyldodecyl)-pyrrolo[3,4-c]pyrrole-1, 4-dione-alt-naphthalene}) (PDPP-TNT) and the fullerene acceptor, ([6,6]-phenyl C71-butyric acid methyl ester) (PC70BM). Atomic force microscopy (AFM) and scanning electron microscopy (SEM) have been used to investigate the morphology of the active layers of the two approaches. Mild thermal treatment of the NP film is required to promote initial joining of the NPs in order for the devices to function, however the NP structure is retained. Consequently, whereas gross phase segregation of the active layer occurs in the BHJ device spin cast from chloroform, the nanoparticulate approach retains control of the material domain sizes on the length scale of exciton diffusion in the materials. As a result, NP devices are found to generate more than twice the current density of BHJ devices and have a substantially greater overall efficiency. The use of aqueous nanoparticulate dispersions offers a promising approach to control the donor acceptor morphology on the nanoscale with the benefit of environmentally- friendly, solution-based fabrication. © 2014 the Owner Societies.