Effect of physical aging on phenolphthalein polyethersulfone/poly(phenylene sulfide) blend .1. Mechanical properties

The effect of physical aging at 210 degrees C on the mechanical properties of phenolphthalein polyether sulfone (PES-C) and a PES-C/poly(phenylene sulfide) (PPS) blend, with 5% content of PPS, were studied using DMA, tensile experiments, an instrumented impact tester, and SEM observations. The blend shows good mechanical properties in comparison with the corresponding PES-C. The mechanical properties of both materials exhibit characteristics of physical aging, with only the aging rate of the blend relatively slower, which should be attributed to the constraint effect of PPS particles and the good interfacial adhesion. The morphology of the PPS phase in the blend did not change with aging time. The principal role of PPS particles is to induce crazes, which dissipate energy, under applied loading; thus, the blend shows good toughness. On the other hand, the multiple crazing mechanism depends on the molecular mobility or structural state of the matrix. (C) 1996 John Wiley & Sons, Inc.

Synthesis and properties of block copolymers of poly(ether sulphone)s with liquid crystalline polyester units

Block copolymers of poly(ethersulphone) (PES) oligomers with liquid crystalline polyester units were synthesized by the reaction of dihydroxy-terminated poly(ether sulphone) oligomers (number-average molecular weights: 704, 1,158 and 2570) and terephthaloyl bis(4-oxybenzoyl chloride), and their properties were investigated. The results indicated that the copolymer with PES segments of molecular weight of 704 possessed birefringent features when annealed at 360 degrees C, while the copolymer with PES segments of molecular weight of 2,570 became isotropic. Also, the block copolymers had a better chemical resistance and high-temperature stability than PES.

Extreme ultraviolet (EUV) degradation of poly(olefin sulfone)s : towards applications as EUV photoresists

Poly(olefin sulfone)s, formed by the reaction of sulfur dioxide (SO2) and an olefin, are known to be highly susceptible to degradation by radiation and thus have been identified as candidate materials for chain scission-based extreme ultraviolet lithography (EUVL) resist materials. In order to investigate this further, the synthesis and characterisation of two poly(olefin sulfone)s namely poly(1-pentene sulfone) (PPS) and poly(2-methyl-1-pentene sulfone) (PMPS), was achieved and the two materials were evaluated for possible chain scission EUVL resist applications. It was found that both materials possess high sensitivities to EUV photons; however; the rates of outgassing were extremely high. The only observed degradation products were found to be SO2 and the respective olefin suggesting that depolymerisation takes place under irradiation in a vacuum environment. In addition to depolymerisation, a concurrent conversion of SO2 moieties to a sulfide phase was observed using XPS.

Which One Is Preferred: Myers-Saito Cyclization of Ene-Yne-Allene or Garratt-Braverman Cyclization of Conjugated Bisallenic Sulfone? A Theoretical and Experimental Study

A competitive scenario between Myers-Saito (MS) and Garraff-Braverman (GB) cyclization has been created in a molecule. High-level computations indicate a preference for GB over MS cyclization. The activation energies for the rate-determining steps of the GB and MS cyclizations were found to be the same (24.4 kcal/mol) at the B3LYP/6-31G* level of theory; thus, from the kinetic point of view, both reactions are feasible. However, the main biradical intermediate GB2 of the GB reaction is 6.2 kcal/mol lower in energy than the biradical MS2, which is the main intermediate of MS reaction, so GB cyclization is thermodynamically favored over MS cyclization. To verify the prediction by computational techniques, bisenediynyl sulfones 1-4 and bisenediynyl sulfoxide 17 were synthesized. Under basic conditions, these molecules isomerized to a system possessing both the ene-yne-allene and the bisallenic sulfone. The isolation of only one product, identified as the corresponding naphthalene- or benzene-fused sulfone 8-11, indicated the occurrence of GB cyclization as the sole reaction pathway. No product corresponding to the MS cyclization pathway could be isolated. Though the theoretical prediction showed a preference for the GB pathway over the MS pathway, the exclusive preference for GB over MS cyclization is very striking. Further analysis showed that the intramolecular self-quenching nature of the GB pathway may play an important role in the complete preference for this reaction. Apart from the mechanistic studies, these sulfones showed DNA cleavage activity that had an inverse relation with the reactivity order. Our findings are important for the design of artificial DNA-cleaving agents.

SEC-MALDI-TOF mass spectral characterization of a hyperbranched polyether prepared via melt transetherification

An AB(2) monomer, 1-(2-hydroxyethoxy)-3,5-bis-(methoxymethyl)-2,4,6-trimethylbenzene, was synthesized from mesitol and melt-polycondensed in the presence of an acid catalyst via a transetherification process at 145-150 degreesC to yield a soluble, moderately high molecular weight hyperbranched polyether. The degree of branching in the polymer was calculated to be 0.78 by a comparison of its NMR spectrum with that of an appropriately designed model compound. The weight-average molecular weight of the hyperbranched polymer was determined to be 64,600 (weight-average molecular weight/number-average molecular weight = 5.2) by size exclusion chromatography (SEC) in CHCl3, with polystyrene standards. The origin of the broad molecular weight distribution, which could either be intrinsic to such hyperbranched structures or be due to structural heterogeneity, was further probed by the fractionation of the samples by SEC and by the subjection of each fraction to matrix-assisted laser desorption/ionization time-of-flight mass spectral analysis. The mass spectral analysis suggested the presence of two primary types of species: one corresponding to the simple branched structure and the other to macrocyclics. Interestingly, from the relative intensities of the two peaks, it was apparent that cyclization became favorable at higher conversions in the melt transetherification process. (C) 2002 Wiley Periodicals, Inc.

Synthesis, antimicrobial and cytotoxic activities of sulfone linked bis heterocycles

A new class of sulfone linked bis heterocycles viz., pyrrolyl/pyrazolyl arylaminosulfonylmethyl 1,3,4-oxadiazoles, 1,3,4-thiadiazoles, and 1,2,4-triazoles were prepared and tested for antimicrobial activity and cytotoxicity. The chloro-substituted compounds 5c, 8c and 14c showed comparable antibacterial activity to chloramphenicol against Pseudomonasaeruginosa and compound 5c exhibited comparable antifungal activity to ketoconazole against Penicilliumchrysogenum. One of the compounds, vinylsulfonyl oxadiazole showed appreciably cytotoxic activity on A549 lung carcinoma cells with an IC50 at a concentration of 31.7 mu M. (C) 2012 Elsevier Masson SAS. All rights reserved.

Desenvolvimento de membranas de poli(éter imida) sultonada para a permeacão de gases

A busca por membranas com propriedades adequadas a separação de gases em escala industrial tem levado a modificação e sIntese de polImeros de engenharia, com objetivo de obter membranas com propriedades adequadas. Uma das modificaçoes que tem se apresentado promissora é a inserção de grupos sulfônicos em polImeros comerciais. Espera-se que o polImero sulfonado apresente um aumento na permeação de gases polares, em relação a gases apolares, devido a sua estrutura mais polar e flexIvel. Neste contexto, o objetivo do presente trabalho é a sIntese e caracterização de membranas de poli(éter imida) sulfonada para a permeação de gases. Um planejamento experimental foi desenvolvido, em diferentes condiçoes reacionais de temperatura, tempo e excesso de um dos reagentes (ácido acético), para a sIntese de poli(éter imida) sulfonada (SPEI). Através deste planejamento, constatou-se que as variáveis que mais influenciam o grau de sulfonação são a temperatura e o tempo. O polImero com o maior grau de sulfonação, determinado por capacidade de troca iônica (IEC= 92 mEq H+/g), foi utilizado para o preparo da membrana de SPEI, obtida pela técnica de inversão de fase por evaporação do solvente, utilizando-se clorofórmio como solvente. Este filme foi caracterizado a partir das seguintes análises: espectroscopia de infravermelho (FTIR), calorimetria diferencial de varredura (DSC), análise termogravimétrica (TGA) e microscopia eletrônica de varredura (MEV), a fim de avaliar a influência da inserção do grupo sulfônico na matriz polimérica. O espectro de infravermelho de SPEI apresentou bandas relacionadas as vibraçoes assimétricas em 1240 cm-1 (ligação O=S=O), ligação simétrica em 1171 cm-1 (O=S=O) e ligação S-O entre 1010-1024 cm-1. Isto indica a presença de grupos sulfônicos. A análise de DSC foi realizada entre 150-250C. Nesta faixa, não foram observadas alteraçoes na temperatura de transição vItrea (Tg) do polImero modificado (217C). Acredita-se que a decomposição do grupo sulfona aconteça antes da temperatura atingir o Tg do polImero. Esta suposição é confirmada na análise de TGA. As imagens de MEV mostraram que foram obtidos filmes livres de poros e defeitos. A membrana da SPEI foi utilizada no ensaio de permeaçao dos gases 02, N2 e C02, a fim de determinar a permeabilidade e seletividade da membrana. As permeabilidades encontradas para o gas oxigênio foram de 0,76 barrer para a PEI e 0,46 barrer para a SPEI. A seletividade do dióxido de carbono em relaçao ao oxigênio aumentou de 3,5, na membrana de PEI, para 4,83, na membrana de SPEI. Em relaçao ao nitrogênio, as permeabilidades medidas foram 0,064 barrer e 0,043 barrer, para a PEI e para a SPEI, respectivamente, enquanto a seletividade em relaçao ao C02 aumentou de 41,1 para 55,5. Estes resultados indicam que o efeito de sorçao predominou devido ao aumento das interaçöes moleculares, reduzindo assim o volume livre, o que tornou a membrana sulfonada mais compacta, com permeabilidade menor e maior seletividade. Estes resultados corroboram com a premissa de que a sulfonaçao é um processo promissor para o desenvolvimento de membranas mais eficientes.

Analysis of estrogens in environmental waters using polymer monolith in-polyether ether ketone tube solid-phase microextraction combined with high-performance liquid chromatography

A simple, rapid and sensitive on-line method for simultaneous determination of four endocrine disruptors (17 beta-estradiol, estriol, bisphenol A and 17 alpha-ethinylestradiol) in environmental waters was developed by coupling in-tube solid-phase microextraction (SPME) to high-performance liquid chromatography (HPLC) with fluorescence detection (FLD). A poly(acrylamide-vinylpyridine-NAP-methylene bisacrylamide) monolith, synthesized inside a polyether ether ketone (PEEK) tube, was selected as the extraction medium. To achieve optimum extraction performance, several parameters were investigated, including extraction flow-rate, extraction time, and pH value, inorganic salt and organic solvent content of the sample matrix. By simply filtered with nylon membrane filter and adjusting the pH of samples to 6.0 with phosphoric acid, the sample solution then could be directly injected into the device for extraction. Low detection limits (S/N = 3) and quantification limits (S/N = 10) of the proposed method were achieved in the range of 0.006-0.10 ng/mL and 0.02-0.35 ng/mL from spiked lake waters, respectively. The calibration curves of four endocrine disruptors showed good linearity ranging from quantification limits to 50 ng/mL with a linear coefficient R-2 value above 0.9913. Good method reproducibility was also found by intra- and inter-day precisions, yielding the RSDs less than 12 and 9.8%, respectively. Finally, the proposed method was successfully applied to the determination of these compounds in several environmental waters. (c) 2006 Elsevier B.V. All rights reserved.

Preparation and properties of polyether pentaerythritol mono-maleate grafted linear low density polyethylene by reactive extrusion

A reactive type nonionic surfactant, polyether pentaerythritol mono-maleate (PPMM) was synthesized in our laboratory. PPMM was adopted as functionalizing monomer and grafted onto linear low density polyethylene (LLDPE) with a melt reactive extrusion procedure. FT-IR was used to characterize the formation of grafting copolymer and evaluate their degree of grafting. The effects of monomer concentration, reaction temperature and screw run speed on the degree of grafting were studied systematically. Isothermal crystallization kinetics of LLDPE and LLDPE-g-PPMM samples was carried out using DSC.

Novel thin-film composite membranes with improved water flux from sulfonated cardo poly(arylene ether sulfone) bearing pendant amino groups

A new class of polymeric amine, namely, sulfonated cardo poly(arylene ether sulfone) (SPES-NH2) was synthesized and used for the preparation of thin-film composite membrane. The TFC membranes were prepared on a polysulfone supporting film through interfacial polymerization with trimesoyl chloride (TMC) solutions and amine solutions containing SPES-NH2 and m-phenylenediamine (MPDA). The resultant membranes were characterized with water permeation performance, chemical structure, hydrophilicity of active layer and membrane morphology including top surface and cross-section.

Synthesis of Soluble Poly(arylene ether sulfone) Ionomers with Pendant Quaternary Ammonium Groups for Anion Exchange Membranes

A new bisphenol monomer, 2,2'-dimethylaminemetllylene-4,4'-biphenol (DABP), was easily prepared by Mannich reaction of dimethylamine and formaldehyde with 4,4'-biphenol. Novel partially fluorinated poly(arylene ether sulfone)s with pendant quaternary ammonium groups were prepared by copolymerization of DABP, 4,4'-biphenol, and 3,3',4,4'- tetrafluorodiphenylsulfone, followed by reaction with iodomethane. The resulting copolymers PSQNI-x (where x represents the molar fraction of DABP in the feed) with high molecular weight exhibited outstanding solubility in polar aprotic solvents; thus, the flexible and tough membranes of PSQNI-x with varying ionic content could be prepared by casting from the DMAc solution. Novel anion exchange membranes, PSQNOH-x, were obtained by an anion exchange of PSQNI-x with 1 N NaOH.

Synthesis, properties, and gas permeation performance of cardo poly(arylene ether sulfone)s containing phthalimide side groups

Novel bisphenol monomers (1a-d) containing phthalimide groups were synthesized by the reaction of phenolphthalein with ammonia, methylamine, aniline, and 4-tert-butylanilne, respectively. A series of cardo poly (arylene ether sulfone)s was synthesized via aromatic nucleophilic substitution of 1a-d with dichlorodiphenylsulfone, and characterized in terms of thermal, mechanical and gas transport properties to H-2, O-2, N-2, and CO2. The polymers showed high glass transition temperature in the range 230-296 degrees C, good solubility in polar solvents as well as excellent thermal stability with 5% weight loss above 410 degrees C. The most permeable membrane studied showed permeability coefficients of 1.78 barrers to O-2 and 13.80 barrers to CO2, with ideal selectivity. factors of 4.24 for O-2/N-2 pair and 28.75 for CO2/CH4 pair. Furthermore, the structure-property relationship among these cardo poly(arylene ether sulfone)s had been discussed on solubility, thermal stability, mechanical, and gas permeation properties. The results indicated that introducing 4-tert-butylphenyl group improved the gas permeability of polymers evidently.

Cyclic oligomers of phenolphthalein polyarylene ether sulfone (ketone): Preparation through cyclo-depolymerisation of corresponding polymers

Cyclic oligomers of phenolphthalein polyarylene ether sulfone(ketone) were prepared through cyclo-depolymerisation of corresponding polymers using CsF as the catalyst in dipolar aprotic solvent DMAc and DMF, and a family of macrocycles containing from dimer up to at least heptamer were confirmed. by GPC, HPLC and MALDI-TOF-MS. The yields of cyclics get as high as 86.3% and 87.9% respectively.