Características estruturais e fotocatalíticas do compósito oxihidróxido de nióbio/vermiculita

The preparation of nanostructured materials using natural clays as support, has been studied in literature under the same are found in nature and consequently, have a low price. Generally, clays serve as supports for metal oxides by increasing the number of active sites present on the surface and can be applied for various purposes such as adsorption, catalysis and photocatalysis. Some of the materials that are currently highlighted are niobium compounds, in particular, its oxides, by its characteristics such as high acidity, rigidity, water insolubility, oxidative and photocatalytic properties. In this scenario, the study aimed preparing a composite material oxyhydroxide niobium (NbO2OH) / sodium vermiculite clay and evaluate its effectiveness with respect to the natural clay (V0) and NbO2OH. The composite was prepared by precipitation-deposition method and then characterized by X-ray diffraction, infrared spectroscopy (XRD), energy dispersive X-ray (EDS), thermal analysis (TG/DTG), scanning electron microscopy (SEM), N2 adsorption-desorption and investigation of distribution of load. The application of the material NbO2OH/V0 was divided in two steps: first through oxidation and adsorption methods, and second through photocatalytic activity using solar irradiation. Studies of adsorption, oxidation and photocatalytic oxidation monitored the percentage of color removal from the dye methylene blue (MB) by UV-Vis spectroscopy. The XRD showed a decrease in reflection d (001) clay after modification; the FTIR indicated the presence of both the clay when the oxyhydroxide niobium to present bands in 1003 cm-1 related to Si-O stretching bands and 800 cm-1 to the Nb-O stretching. The presence of niobium was also confirmed by EDS indicated that 17 % by mass amount of the metal. Thermal analysis showed thermal stability of the composite at 217 °C and micrographs showed that there was a decrease in particle size. The investigation of the surface charge of NbO2OH/V0 found that the material exhibits a heterogeneous surface with average low and high negative charges. Adsorption tests showed that the composite NbO2OH/V0 higher adsorption capacity to remove 56 % of AM, while the material removed from V0 only 13 % showed no NbO2OH and adsorptive capacity due to the formation of H-aggregates. The percent removal of dye color for the oxidation tests showed little difference from the adsorption, being 18 and 66 % removal of dye color for V0 and NbO2OH/V0 respectively. The NbO2OH/V0 material shows excellent photocatalytic activity managing to remove just 95,5 % in 180 minutes of the color of MB compared to 41,4 % and 82,2 % of V0 the NbO2OH, proving the formation of a new composite with distinct properties of its precursors.

Caracterização por microscopia eletrônica de transmissão do aço SAE5115 microligado ao nióbio para cementação em altas temperaturas

A busca de uma maior competitividade tem levado a indústria a utilizar temperaturas de cementação cada vez mais elevadas. Este aumento na temperatura permite uma significativa diminuição dos tempos de tratamentos, porém pode levar a um aumento generalizado ou anormal do tamanho de grão austenítico bastante deletério as propriedades mecânicas do material. A utilização de elementos formadores de precipitados é uma alternativa para minimizar este problema. Neste trabalho foi estudado um aço SAE 5115 com adição de 0,038% em peso nióbio para ancoramento de grão. Para este estudo foi simulado um tratamento térmico de cementação em temperaturas mais elevadas, como 1000 e 1050°C, por duas horas, partindo-se de duas condições, bruto de laminação e esferoidizado. A técnica de microscopia eletrônica de transmissão (MET) foi empregada para caracterizar os precipitados, bem como avaliar sua contribuição no ancoramento do grão. A caracterização dos precipitados quanto sua composição, morfologia, tamanho e distribuição, foi realizada analisando-se amostras preparadas por extração de réplicas em filme de carbono e por lâminas finas pelo método de polimento plano no “Tripod Polisher”. Sendo que este último, convencionalmente não utilizado em aço, possibilita a obtenção de amostras com extensa área fina para observação no MET, além de facilitar a análise por minimizar o efeito de desvio de feixe em amostras magnéticas. Os resultados das análises comprovam a precipitação de partículas complexas de Nb e que a forma de distribuição, bem como o percentual de tamanho dos precipitados é de suma importância para o ancoramento do grão. Verificou-se uma tendência maior para o aparecimento de grão anormal nas amostras que sofreram o processo de esferoidização.

Desenvolvimento de um aço SAE 5115 microligado ao nióbio para cementação a alta temperatura

Este trabalho busca desenvolver um aço para cementação a alta temperatura através da adição de nióbio como microligante, a fim de que os compostos formados forneçam partículas de segunda fase que atuem como ancoradoras do grão austenítico, já que o processo de crescimento de grão, especialmente anormal, é conseqüência natural das temperaturas envolvidas. A elevação da temperatura tem como objetivo proporcionar um ganho em produtividade pela redução dos tempos de cementação. Procura-se também estabelecer uma comparação do aço proposto a aços de cementação convencionais (DIN 17Cr3 e SAE 5115). Utilizou-se um aço SAE 5115 com 0,034% de nióbio, que foi submetido a diferentes condições de ensaio em laboratório: deformação a frio por compressão livre em três graus de deformação (isento, 25 e 50%); com posterior aquecimento em patamares de temperatura que simulam diferentes níveis de cementação (930 , 950 , 1000 e 1050 C), bem como diferentes tempos de manutenção em temperatura, de tal forma a atingir camadas cementadas hipotéticas em torno de 1,0 mm de profundidade. Encerram-se os testes submetendo o aço estudado a um processo de produção industrial de pinos de pistão, que sofrem deformação a temperatura ambiente e cementação a 950 C por 2,5 h O aço SAE 5115 ao “Nb” mostrou um melhor desempenho no controle dos grãos austeníticos, tanto para os ensaios de simulação realizados em laboratório e comparados ao aço DIN 17Cr3, como frente ao processo de produção de pinos de pistão tendo como comparativo o aço SAE 5115. O modelo teórico de Hudd e outros (que trata os carbonitretos de nióbio como de extensiva solubilidade mútua) e o de Gladman (que define os nitretos de alumínio e de nióbio como mutuamente exclusivos), associados às equações de Wagner (para coalescimento das partículas de segunda fase), bem como à equação de Gladman e Pickering (que determina o raio crítico de partícula para uma distribuição aleatória de partículas), mostraram-se bastante adequados em prever a resposta das partículas precipitadas, partindo-se da composição química do aço, principalmente para as partículas de carbonitreto de nióbio em condições que não envolvessem níveis elevados de deformação.

Caracterização metalúrgica do aço SAE 1141 microligado ao nióbio por simulação física

Este trabalho analisa, através do emprego de simulador físico, os efeitos da adição do nióbio no aço SAE 1141 e seu comportamento como refinador de grão e endurecedor por precipitação, nas altas temperaturas de forjamento e tempos de reaquecimento aplicados industrialmente. Analisa também qual a influência das deformações e velocidades de resfriamento sobre o tamanho de grão austenítico, microestrutura, dureza, cinética da precipitação e propriedades finais. Na definição dos parâmetros de simulação foram observadas rotinas de produção de peças forjadas comercialmente, a literatura técnica, e possíveis alterações que otimizassem as propriedades do aço em estudo. Para tanto foram definidas as temperaturas de forjamento 1100, 1200 e 1250°C, a taxa de deformação de 1/s, as deformações de 30, 50 e 70%, e as velocidades de resfriamento de 36, 60, 100 e 150°C/min. Os resultados indicaram que a velocidade de resfriamento tem papel preponderante na microestrutura final, que variou de um agregado de ferrita e perlita para bainita (às vezes com alguma martensita) a medida em que a velocidade de resfriamento aumenta. A simulação térmica indicou que tamanho de grão austenítico aumenta a medida em que se eleva a temperatura de reaquecimento e que existe apenas um pequeno efeito ancorador de grão do nióbio nesse quesito, quando não estiver presente alguma deformação Foi observado, através da simulação física que, com a presença de deformação, principalmente para as temperaturas menores de reaquecimento, a precipitação induzida por deformação parece ancorar o crescimento dos grãos recristalizados, resultando num tamanho de grão austenítico menor. Esse trabalho constitui parte integrante do projeto de desenvolvimento da tecnologia dos aços microligados, num esforço conjunto do Laboratório de Metalurgia Física – LAMEF, através do Grupo de Desenvolvimento de Aços Microligados, da Universidade Federal do Rio Grande do Sul, em parceria com a Aços Finos Piratini e DANA – Albarus, com o apoio da CAPES.

Sinterização de aço inoxidável reforçado com partículas nanométricas dispersas de carbeto de nióbio - NbC

Metal powder sintering appears to be promising option to achieve new physical and mechanical properties combining raw material with new processing improvements. It interest over many years and continue to gain wide industrial application. Stainless steel is a widely accepted material because high corrosion resistance. However stainless steels have poor sinterability and poor wear resistance due to their low hardness. Metal matrix composite (MMC) combining soft metallic matrix reinforced with carbides or oxides has attracted considerable attention for researchers to improve density and hardness in the bulk material. This thesis focuses on processing 316L stainless steel by addition of 3% wt niobium carbide to control grain growth and improve densification and hardness. The starting powder were water atomized stainless steel manufactured for Höganäs (D 50 = 95.0 μm) and NbC produced in the UFRN and supplied by Aesar Alpha Johnson Matthey Company with medium crystallite size 16.39 nm and 80.35 nm respectively. Samples with addition up to 3% of each NbC were mixed and mechanically milled by 3 routes. The route1 (R1) milled in planetary by 2 hours. The routes 2 (R2) and 3 (R3) milled in a conventional mill by 24 and 48 hours. Each milled samples and pure sample were cold compacted uniaxially in a cylindrical steel die (Ø 5 .0 mm) at 700 MPa, carried out in a vacuum furnace, heated at 1290°C, heating rate 20°C stand by 30 and 60 minutes. The samples containing NbC present higher densities and hardness than those without reinforcement. The results show that nanosized NbC particles precipitate on grain boundary. Thus, promote densification eliminating pores, control grain growth and increase the hardness values

Estudo e desenvolvimento de um capacitor eletrolítico de nióbio

It seeks to find an alternative to the current tantalum electrolytic capacitors in the market due to its high cost. Niobium is a potential substitute, since both belong to the same group of the periodic table and because of this have many similar physical and chemical properties. Niobium has several technologically important applications, and Brazil has the largest reserves, around 96%. There are including niobium in reserves of tantalite and columbite in Rio Grande do Norte. These electrolytic capacitors have high capacitance specifies, ie they can store high energy in small volumes compared to other types of capacitors. This is the main attraction of this type of capacitor because is growing demand in the production of capacitors with capacitance specifies increasingly high, this because of the miniaturization of various devices such as GPS devices, televisions, computers, phones and many others. The production route of the capacitor was made by powder metallurgy. The initial niobium powder supplied by EEL-USP was first characterized by XRD, SEM, XRF and laser particle size, to then be sieved into three particle size, 200, 400 e 635mesh. The powders were then compacted and sintered at 1350, 1450 and 1550°C using two sintering time 30 and 60min. Sintering is one of the most important parts of the process as it affects properties as porosity and surface cleaning of the samples, which greatly affected the quality of the capacitor. The sintered samples then underwent a process of anodic oxidation, which created a thin film of niobium pentóxido over the whole porous surface of the sample, this film is the dielectric capacitor. The oxidation process variables influence the performance of the film and therefore the capacitor. The samples were characterized by electrical measurements of capacitance, loss factor, ESR, relative density, porosity and surface area. After the characterizations was made an annealing in air ate 260ºC for 60min. After this treatment were made again the electrical measurements. The particle size of powders and sintering affected the porosity and in turn the specific area of the samples. The larger de area of the capacitor, greater is the capacitance. The powder showed the highest capacitance was with the smallest particle size. Higher temperatures and times of sintering caused samples with smaller surface area, but on the other hand the cleaning surface impurities was higher for this cases. So a balance must be made between the gain that is achieved with the cleaning of impurities and the loss with the decreased in specific area. The best results were obtained for the temperature of 1450ºC/60min. The influence of annealing on the loss factor and ESR did not follow a well-defined pattern, because their values increased in some cases and decreased in others. The most interesting results due to heat treatment were with respect to capacitance, which showed an increase for all samples after treatment

Comportamento da adição do carbeto de nióbio (nBC) na matriz metálica do aço ferrítico 15kH2mfa

The 15Kh2MFA steel is a kind of Cr-Mo-V family steels and can be used in turbines for energy generation, pressure vessels, nuclear reactors or applications where the range of temperature that the material works is between 250 to 450°C. To improve the properties of these steels increasing the service temperature and the thermal stability is add a second particle phase. These particles can be oxides, carbides, nitrites or even solid solution of some chemical elements. On this way, this work aim to study the effect of addition of 3wt% of niobium carbide in the metallic matrix of 15Kh2MFA steel. Powder metallurgy was the route employed to produce this metallic matrix composite. Two different milling conditions were performed. Condition 1: milling of pure 15Kh2MFA steel and condition 2: milling of 15Kh2MFA steel with addition of niobium carbide. A high energy milling was carried out during 5 hours. Then, these two powders were sintered in a vacuum furnace (10-4torr) at 1150 and 1250°C during 60 minutes. After sintering the samples were normalized at 950°C per 3 minutes followed by air cooling to obtain a desired microstructure. Results show that the addition of niobium carbide helps to mill faster the particles during the milling when compared with that steel without carbide. At the sintering, the niobium carbide helps to sinter increasing the density of the samples reaching a maximum density of 7.86g/cm³, better than the melted steel as received that was 7,81g/cm³. In spite this good densification, after normalizing, the niobium carbide don t contributed to increase the microhardness. The best microhardness obtained to the steel with niobium carbide was 156HV and to pure 15Kh2MFA steel was 212HV. It happened due when the niobium carbide is added to the steel a pearlitic structure was formed, and the steel without niobium carbide submitted to the same conditions reached a bainitic structure

Avaliação cinética e potencial do Nb2O5 obtido a partir de um complexo de nióbio para formação do oleato de metila através da reação de esterificação do ácido oleico

Among the heterogeneous catalysts materials made from niobium show up as an alternative to meet the demand of catalysts for biodiesel production. This study aims to evaluate the potential of a heterogeneous catalyst derived from a complex of niobium in the reaction of methyl esterification of oleic acid. The catalyst was synthesized after calcination at different temperatures of a niobium complex ((NH4)3[NbO(C2O4)3].H2O) generating a niobium oxide nanostructure with a different commercial niobium oxide used to synthesize the complex. The commercial niobium oxide, the complex niobium and niobium catalyst were characterized by thermogravimetry (TG and DTA), surface area analysis (BET), scanning electron microscopy (SEM) and X-ray diffraction (XRD), showing the catalyst has researched morphological and crystallographic indicating a catalytic potential higher than that of commercial niobium oxide characteristics. Factorial with central composite design point, with three factors (calcination temperature, molar ratio of alcohol/oleic acid and mass percentage of catalyst) was performed. Noting that the optimal experimental point was given by the complex calcination temperature of 600°C, a molar ratio alcohol/oleic acid of 3.007/1 and the catalyst mass percentage of 7.998%, with a conversion of 22.44% oleic acid in methyl oleate to 60 min of reaction. We performed a composite linear and quadratic regression to determine an optimal statistical point of the reaction, the temperature of calcination of the complex at 450°C, the molar ratio of alcohol/oleic acid 3.3408/1 and mass percentage of catalyst of 7.6833% . Kinetic modeling to estimate parameters for heterogeneous catalysis it set well the experimental results with a final conversion of 85.01% with 42.38% of catalyst and without catalyst at 240 min reaction was performed. Allowing to evaluate the catalyst catalytic studied has the potential to be used in biodiesel production

Desenvolvimento de um secador spray para obtenção de pós finos de precursores de nióbio

This work presents a spray-dryer designed to oxalate-niobate precursors and suitable for the production of Niobium Carbide. The dryer was intended to produce powders of controlled particle size. First, the precursor is dissolved in water to produce a solution of known concentration and then it is atomized on the spray-dryer to produce the powder. This equipment consists of a 304 stainless steel chamber, 0.48 m x 1.9 m (diameter x length), with a conical shape at the lower portion, which is assembled on a vertical platform. The chamber is heated by three 4 kW electrical resistances. In this process, drying air is heated as it flows inside a serpentine surrounding the chamber, in contrary to more traditional processes in which the hot drying air is used to heat the component. The air enters the chamber at the same temperature of the chamber, thus avoiding adherence of particles on the internal surface. The low speed flow is concurrent, directed from the top to the bottom portion of the chamber. Powders are deposited on a 0.4 m diameter tray, which separates the cylindrical portion from the conical portion of the chamber. The humid air is discharged though a plug placed underneath the collecting tray. A factorial experimental planning was prepared to study the influence of five parameters (concentration, input flow, operation temperature, drying air flow and spray air flow) on the characteristics of the powders produced. Particle size distribution and shape were measured by laser granulometry and scanning electronic microscopy. Then, the powders are submitted to reaction in a CH4 / H2 atmosphere to compare the characteristics of spray-dried powders with powders synthetizided by conventional methods

Caracterização e propriedades catalíticas da zeolita HZSM5 modificada com nióbio

HZSM5 zeolite was modified by exchanging proton by niobium (V). Several samples were obtained with various degrees of exchange. Pore volumes and acidity were measured to characterize these exchanged zeolites. Catalytic properties were evaluated with two reaction tests: m-xylene transformation and n-heptane cracking. The introduction of niobium on HZSM5 zeolite decreases the diffusion coefficient of 2-methyl-pentane and increases the zeolite acidity. The sample containing niobium are initially more active in cracking of n-heptane and m-xylene isomerization than HZSM5 alone.

Estudos sobre a síntese de piperidinas funcionalizadas através de reações pentacomponentes, utilizando compostos de nióbio como catalisadores

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Síntese e caracterização da cerâmica PZT dopada com estrôncio e com nióbio e estrôncio

Pós-graduação em Química - IQ

Estudo do efeito do tempo e do meio de moagem de alta energia para obtenção de pós nanométricos de hidretos de titânio e nióbio

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo sobre o uso de compostos de nióbio em reações multicomponentes de aza-Diels-Alder

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Preparação e caracterização estrutural de complexos quirais de nióbio, utilizando álcoois terpênicos quirais como ligantes

Pós-graduação em Ciência e Tecnologia de Materiais - FC