Permeability, overburden stress and friction coefficients of ODP Hole 190-1173A and 190-1174B

Permeability measured on three samples in a triaxial cell under effective confining pressure from 0.2 to 2.5 MPa ranges from 10**-18 to 10**-19 m**2. Overall, results indicate that permeability decreases with effective confining pressure up to 1.5 MPa; however, measurements at low effective pressure are too dispersed to yield a precise general relationship between permeability and pressure. When the effective pressure is increased from 1.5 to 2.5 MPa, permeability is roughly constant (~1-4 x 10**-19 m**2). Samples deformed in the triaxial cell developed slickenlined fractures, and permeability measurements were performed before and after failure. A permeability increase is observed when the sample fails under low effective confining pressure (0.2 MPa), but not under effective pressure corresponding to the overburden stress. Under isotropic stress conditions, permeability decrease related to fracture closure occurs at a relatively high effective pressure of ~1.5 MPa. Coefficients of friction on the fractures formed in the triaxial cell are ~0.4.

Pore pressure measurements on IODP Exp308 sites

Overpressures measured with pore pressure penetrometers during Integrated Ocean Drilling Program (IODP) Expedition 308 reach 70% and 60% of the hydrostatic effective stress (View the MathML source) in the first 200 meters below sea floor (mbsf) at Sites U1322 and U1324, respectively, in the deepwater Gulf of Mexico, offshore Louisiana. High overpressures are present within low permeability mudstones where there have been multiple, very large, submarine landslides during the Pleistocene. Beneath 200 mbsf at Site U1324, pore pressures drop significantly: there are no submarine landslides in this mixture of mudstone, siltstone, and sandstone. The penetrometer measurements did not reach the in situ pressure at the end of the deployment. We used a soil model to determine that an extrapolation approach based on the inverse of square route of time (View the MathML source) requires much less decay time to achieve a desirable accuracy than an inverse time (1/t) extrapolation. Expedition 308 examined how rapid and asymmetric sedimentation above a permeable aquifer drives lateral fluid flow, extreme pore pressures, and submarine landslides. We interpret that the high overpressures observed are driven by rapid sedimentation of low permeability material from the ancestral Mississippi River. Reduced overpressure at depth at Site U1324 suggests lateral flow (drainage) whereas high overpressure at Site U1322 requires inflow from below: lateral flow in the underlying permeable aquifer provides one mechanism for these observations. High overpressure near the seafloor reduces slope stability and provides a mechanism for the large submarine landslides and low regional gradient (2°) offshore from the Mississippi delta.

Role of compaction versus aggregate disruption on slumping and shrinking of repacked hardsetting seedbeds

Slumping of hardsetting seedbeds upon wetting is likely to determine the shrinking and development of strength on drying. Different processes have been invoked, including aggregate disruption, material relocation, and compaction. To gain a better understanding of the role played by compaction compared with aggregate disruption in seedbed slumping and shrinking, mechanical analysis was combined with previous morphogenetical description. The global structural behavior of repacked seedbeds of a hardsetting sandy loam soil was studied after wetting and again after subsequent drying. Bulk density was measured in 5-mm-depth increments using gamma attenuation, and water content was determined at 10-mm-depth increments. Various wetting conditions were used to simulate a range of climatic and management conditions, including flood irrigation, furrow irrigation of a formed seedbed, drip irrigation, and rainfall. Aggregate coalescence under overburden pressure played the main role in slumping, even though microcracking enhanced coalescence. Most of the slumping occurred at calculated effective stress > 1.1 kPa. Intense aggregate breakdown at the top of seedbeds under fast wetting led to slight slumping because the resulting clogging of the initial interaggregate packing voids was balanced, in part, by the increase in microporosity resulting from aggregate disruption. However, aggregate coalescence induced by overburden pressure developing at the seedbed bottom often resulted in a strong decrease in total porosity. The effect of rainfall kinetic energy on crust bulk density was strong compared with the effect of fast wetting (bulk density increase of about 0.07 Mg m(-3) and 0.03 Mg m(-3), respectively) and could be ascribed to compaction rather than to aggregate breakdown. Shrinking on drying was related to the continuity of the microstructure resulting from wetting rather than to the intensity of slumping. Aggregate breakdown led to more shrinking than did aggregate coalescence.

Micromorphological study of slumping in a hardsetting seedbed under various wetting conditions

Slumping of hardsetting seedbeds upon wetting has not been extensively studied despite the likelihood that it determines the physical properties after drying. Slumping results from processes similar to those involved in crusting except that overburden pressure can dominate rather than rainfall kinetic energy. Only a few studies have dealt with the morphological description of slumping. To simulate different climatic and management conditions, repacked seedbeds of a hardsetting sandy-loam soil were subjected to a range of wetting conditions, e.g. capillary rise, immersion, and rainfall simulation. Slumping processes were characterized using qualitative and quantitative micromorphological observations of polished blocks and thin sections from resin-impregnated samples. A morphogenetical framework was proposed to help description of the complex associations of processes which can lead to structural collapse (crusting and slumping) on wetting. Three main stages were considered, i.e. aggregate disruption or abrasion, relocation of the released material, and compaction. In the hardsetting material studied here, structural collapse under slow wetting occurred at the bottom of cores due to aggregate coalescence under overburden pressure. Coalescence required aggregate cohesion being reduced by microcracking; therefore, it differed from the coalescence previously described in unstable silty loam soils where microcracking was not necessary for aggregates to coalesce. Macroporosity decreased most strongly under fast wetting due to physical dispersion and aggregate breakdown. Under simulated rainfall, compaction by raindrops could not be distinguish from aggregate breakdown. The role of overburden pressure and of rainfall kinetic energy remains to be stated; new data are required including measurement of total porosity in the initial, wet, and dry states. (C) 2003 Elsevier B.V. All rights reserved.

Novo método para estimativa do gradiente de fratura para poços de petróleo

The development of oil wells drilling requires additional cares mainly if the drilling is in offshore ultra deep water with low overburden pressure gradients which cause low fracture gradients and, consequently, difficult the well drilling by the reduction of the operational window. To minimize, in the well planning phases, the difficulties faced by the drilling in those sceneries, indirect models are used to estimate fracture gradient that foresees approximate values for leakoff tests. These models generate curves of geopressures that allow detailed analysis of the pressure behavior for the whole well. Most of these models are based on the Terzaghi equation, just differentiating in the determination of the values of rock tension coefficient. This work proposes an alternative method for prediction of fracture pressure gradient based on a geometric correlation that relates the pressure gradients proportionally for a given depth and extrapolates it for the whole well depth, meaning that theses parameters vary in a fixed proportion. The model is based on the application of analytical proportion segments corresponding to the differential pressure related to the rock tension. The study shows that the proposed analytical proportion segments reaches values of fracture gradient with good agreement with those available for leakoff tests in the field area. The obtained results were compared with twelve different indirect models for fracture pressure gradient prediction based on the compacting effect. For this, a software was developed using Matlab language. The comparison was also made varying the water depth from zero (onshore wellbores) to 1500 meters. The leakoff tests are also used to compare the different methods including the one proposed in this work. The presented work gives good results for error analysis compared to other methods and, due to its simplicity, justify its possible application

Surface "Waves" on Byrd Glacier, Antarctica

Byrd Glacier has one of the largest ice catchment areas in Antarctica, delivers more ice to the Ross Ice Shelf than any other ice stream, and is the fastest of these ice streams. A force balance, combined with a mass balance, demonstrates that stream flow in Byrd Glacier is transitional from sheet flow in East Antarctica to shelf flow in the Ross Ice Shelf. The longitudinal pulling stress, calculated along an ice flowband from the force balance, is linked to variations of ice thickness, to the ratio of the basal water pressure to the ice overburden pressure where Byrd Glacier is grounded, and is reduced by an ice-shelf buttressing stress where Byrd Glacier is floating. Longitudinal tension peaks at pressure-ratio maxima in grounded ice and close to minima in the ratio of the pulling stress to the buttressing stress in floating ice. The longitudinal spacing of these tension peaks is rather uniform and, for grounded ice, the peaks occur at maxima in surface slope that have no clear relation to the bed slope. This implies that the maxima in surface slope constitute a "wave train" that is related to regular variations in ice-bed coupling, not primarily to bed topography. It is unclear whether these surface "waves" are "standing waves" or are migrating either upslope or downslope, possibly causing the grounding line to either retreat or advance. Deciding which is the case will require obtaining bed topography in the map plane, a new map of surface topography, and more sophisticated modeling that includes ice flow linked to subglacial hydrology in the map plane.

Geometrical Force Balance in Glaciology

The analytical force balance traditionally used in glaciology relates gravitational forcing to ice surface slope for sheet flow and to ice basal buoyancy for shelf flow. It is unable to represent stream flow as a transition from sheet flow to shelf flow by having gravitational forcing gradually passing from being driven by surface slope to being driven by basal buoyancy downslope along the length of an ice steam. This is a serious defect, because ice streams discharge up to 90% of ice from ice sheets into the sea. The defect is overcome by using a geometrical force balance that includes basal buoyancy, represented by the ratio of basal water pressure to ice overburden pressure, as a source of gravitational forcing. When combined with the mass balance, the geometrical force balance provides a holistic approach to ice flow in which resistance to gravitational flow must be summed upstream from the calving front of an ice shelf. This is not done in the analytical force balance, and it provides the ice-thinning rate required by gravitational collapse of ice sheets as interior ice is downdrawn by ice streams.

Sliding of Ice Past an Obstacle at Engabreen, Norway

At Engabreen, Norway, an instrumented panel containing a decimetric obstacle was mounted flush With the bed surface beneath 210 m of ice. Simultaneous measurements of normal and shear stresses, ice velocity and temperature were obtained as dirty basal ice flowed past the obstacle. Our measurements were broadly consistent with ice thickness, flow conditions and bedrock topography near the site of the experiment. Ice speed 0.45 m above the bed was about 130 mm d(-1), much less than the surface velocity of 800 mm d(-1) Average normal stress on the panel was 1.0-1.6 MPa, smaller than the expected ice overburden pressure. Normal stress was larger and temperature was lower on the stoss side than on the lee side, in accord with flow dynamics and equilibrium thermodynamics. Annual differences in normal stresses were correlated with changes in sliding speed and ice-flow direction. These temporal variations may have been caused by changes in ice rheology associated with changes in sediment concentration, water content or both. Temperature and normal stress were generally correlated, except when clasts presumably collided with the panel. Temperature gradients in the obstacle indicated that regelation was negligible, consistent with the obstacle size. Melt rate was about 10% of the sliding speed. Despite high sliding speed, no significant ice/bed separation was observed in the lee of the obstacle. Frictional forces between sediment particles in the ice and the panel, estimated from Hallet's (1981) model, indicated that friction accounted for about 5% of the measured bed-parallel force. This value is uncertain, as friction theories are largely untested. Some of these findings agree with sliding theories, others do not.

Index properties, shear strenghts and consolidation characteristics of ODP Hole 164-995A sediments

Geotechnical properties of sediment from Ocean Drilling Program Leg 164 are presented as: (1) normalized shipboard strength ratios from the Cape Fear Diapir, the Blake Ridge Diapir, and the Blake Ridge; and (2) Atterberg limit, vane shear strength, pocket-penetrometer strength, and constant-rate-of-strain consolidation results from Hole 995A, located on the Blake Ridge. This study was conducted to understand the stress history in a region characterized by high sedimentation rates and the presence of gas hydrates. Collectively, the results indicate that sediment from the Blake Ridge exhibits significant underconsolidated behavior, except near the seafloor. At least 10 m of additional overburden was removed by erosion or mass wasting at Hole 993A on the Cape Fear Diapir, compared to nearby sites.

Geotechnical properties at DSDP Leg 66 Holes

Delineating the interrelationships between tectonics, sedimentation, and geotechnical properties is particularly important for areas subjected to the dynamic affects of convergence. DSDP Leg 66 drilling within the Middle America Trench complex provided a unique opportunity to investigate these interrelationships along a transect of eight drill sites beginning on the trench outer slope and traversing the trench, trench inner slope, and upper continental slope. Investigations of other convergent margins suggest that deformation occurs most rapidly along the lower trench inner slope and is reflected by the geotechnical properties (Carson, 1977; Seely, 1977; and von Huene, 1979). This study focuses on the geotechnical properties of Middle America Trench sediments and the possible affects of convergence on these properties.

Physical properties of sediments at DSDP Holes 78-541 and 78-543

Sediment cored within the Barbados subduction complex at Sites 541 and 542 are underconsolidated. Underconsolidation and changes in physical properties of the cored section can be related to excess pore water pressure that equals the lithostatic load at Site 542 and to major thrust faulting observed at Site 541. Apparently, the pore fluids within the subduction complex are absorbing the tectonic shock of underthrusting. Sediment sampled from the reference Site 543 on the adjacent Atlantic Plate are also underconsolidated. However, underconsolidation in Hole 543 is apparently due to the movement of excess nitrogen gas observed deeper in the hole. Excess gas was not observed at Sites 541 and 542.