Fire analysis of car park building structures

The thermal loading of an open car park building structure is going to be analysed, based on different fire scenarios that depend on the type of vehicle (different heat release rate). The compartment is going to be fixed and the thermal effect on beams is going to be analysed, depending on the vehicle position. The result of simple calculation method will be used to determine several temperature-time curves. The simple calculation method (Hasemi method) is also to be compared with the calculations of the Elefir-EN calculation program to analyse the thermal effect of the localized fire on beams.

IMU aided 3D visual odometry for car-like vehicles

We present a method for calculating odome- try in three-dimensions for car-like ground ve- hicles with an Ackerman-like steering model. In our approach we use the information from a single camera to derive the odometry in the plane and fuse it with roll and pitch informa- tion derived from an on-board IMU to extend to three-dimensions, thus providing odometric altitude as well as traditional x and y transla- tion. We have mounted the odometry module on a standard Toyota Prado SUV and present results from a car-park environment as well as from an off-road track.

Concentration levels of heavy metals and polycyclic aromatic hydrocarbons in car parks at Queensland University of Technology

This study investigates the level of pollutants (polycyclic aromatic hydrocarbons (PAHs) and heavy metals) in three car parks at QUT, one at Kelvin Grove campus and two at the Gardens Point campus. In addition, comparisons between site designs were assessed to identify the possible sources of heavy metals and PAHs. The main contributing source for heavy metals was identified to be from vehicle debris and emissions, while the source of PAHs was identified to be from petrol and diesel engine vehicle emissions. The highest concentration of pollutants was typically found for the 63 micro meter dust samples, proposed to be due to increased surface areas and thus available adsorption sites.

Charakterystyka topoklimatyczna fragmentu wybrzeża klifowego w rejonie Białej Góry (Woliński Park Narodowy)

The Meteorological Section at the scientific camp 2009–2010 conducted a series of meteorological measurements in the region of Biała Góra. The exploration area is located about 2 km east of Międzyzdroje, at the research station of the AMU Faculty of Geographical and Geological Sciences. Members of the section made measurements in the six selected points. The location of points had to reflect the specifics of the area (from the beach to the car park at the research station). The section focused on three basic measurements: air temperature (2009–2010), relative humidity (2009–2010) and atmospheric pressure (2009). This article aims to analyse a topoclimate section of cliff coast in the Wolin National Park. The compilation recognised the impact of various land surfaces, sea and altitude on the variability of air temperature and relative humidity. It notes the varied course of the daily meteorological elements analysed, which is directly related to the value of radiation balance dependent upon the intensity of direct solar radiation. In this article, particular emphasis is applied to the analysis of temperature amplitudes and humidity at different measuring points.

How active are people in metropolitan parks? An observational study of park visitation in Australia

BACKGROUND: Parks are generally an under-utilized resource in the community with great potential to enhance levels of physical activity. If parks are to attract more visitors across a broad cross-section of the population and facilitate increased physical activity, research is needed to better understand park visitor characteristics and how visitors spend their time in parks. The Recording and EValuating Activity in a Modified Park (REVAMP) study is a natural experiment monitoring a park upgrade in a low socioeconomic status (SES) neighborhood. This study described the observed baseline characteristics of park visitors (age, sex) and characteristics of visitation (weekday or weekend day, period of the day) and explored how these characteristics were associated with observed park-based physical activity in two metropolitan parks located Melbourne, Australia. METHODS: Direct observations of park visitors were conducted using a modified version of SOPARC (the System for Observing Play and Recreation in Communities) on four weekdays and four weekend days. During weekdays, observations were conducted every hour from 7:30 am-4:30 pm and on weekend days from 8:30 am-4:30 pm. This equated to a total of 1460 scans across the two parks. Chi-square tests examined bivariate associations between park-based physical activity, and socio-demographic and park visitation characteristics. Logistic regression models examined the odds of being observed engaging in moderate- to vigorous-intensity physical activity relative to lying/sitting/standing according to socio-demographic and park visitation characteristics. RESULTS: In total, 4756 park visitors were observed with the majority visiting on weekend days (87 %) and in the afternoon (41 %). Most visitors (62 %) were lying, sitting or standing, with only 29 % observed engaging in moderate-intensity and 9 % in vigorous-intensity physical activity. Park use differed by time of day, sex, age group, and neighborhood SES. Physical activity was lower for women than men (OR 0.76) and higher among visitors in the high SES area (OR 1.52). CONCLUSIONS: Parks offer substantial opportunities for people of all ages to engage in physical activity; however, this study showed that a large proportion of the park visitors observed were engaged in sedentary pursuits. Further research on how park design, amenities and programming can optimize park visitation and park-based physical activity is needed. TRIAL REGISTRATION: Current controlled trial ISRCTN50745547 , registration date 11.1.2014.

Sustainable transport and the impact on the built environment : Future trends and directions

We love the automobile and the independence that it gives us. We are more mobile than we have ever been before in recorded history. In Australia 80% of journeys are by private motor vehicle. But it is becoming increasingly obvious that this era has a very limited lifespan. Fuel prices have skyrocketed recently with no end in sight. In spite of massive amounts of road construction, our cities are becoming increasingly congested. We desperately need to address climate change and the automobile is a major contributor. Carbon trading schemes will put even more upward pressure on fuel prices. At some point in the near future, most of us will need to reconsider our automobile usage whether we like it or not. The time to plan for the future is now. But what will happen to our mobility when access to cheap and available petroleum becomes a thing of the past? Will we start driving electric/hydrogen/ethanol vehicles? Or will we flock to public transport? Will our public transport systems cope with a massive increase in demand? Will thousands of people take to alternatives such as bicycles? If so, where do we put them? How do we change our roads to cope? How do we change our buildings to suit? Will we need recharging stations in our car park for example? Some countries are less reliant on the car than others e.g. Holland and Germany. How can the rest of the world learn from them? This paper discusses many of the likely outcomes of the inevitable shift away from society’s reliance on petroleum and examines the expected impact on the built environment. It also looks at ways in which the built environment can be planned to help ease the transition to a fossil free world. 1.

A preliminary examination of the effects of changes in motorcycle licensing in Queensland

Several sets of changes have been made to motorcycle licensing in Queensland since 2007, with the aim of improving the safety of novice riders. These include a requirement that a motorcycle learner licence applicant must have held a provisional or open car licence for 12 months, and imposing a 3 year limit for learner licence renewal. Additionally, a requirement to hold an RE (250 cc limited) class licence for a period of 12 months prior to progressing to an R class licence was introduced for Q-RIDE. This paper presents analyses of licensing transaction data that examine the effects of the licensing changes on the duration that the learner licence was held, factors affecting this duration and the extent to which the demographic characteristics of learner licence holders changed. The likely safety implications of the observed changes are discussed.

Can compensation be claimed under the standard commercial land and building contract where the property sold has no legally enforceable vehicular access?

This was the question that confronted Wilson J in Jarema Pty Ltd v Michihiko Kato [2004] QSC 451. Facts The plaintiff was the buyer of a commercial property at Bundall. The property comprised a 6 storey office building with a basement car park with 54 car parking spaces. The property was sold for $5 million with the contract being the standard REIQ/QLS form for Commercial Land and Buildings (2nd ed GST reprint). The contract provided for a “due diligence” period. During this period, the buyer’s solicitors discovered that there was no direct access from a public road to the car park entrance. Access to the car park was over a lot of which the Gold Coast City Council was the registered owner under a nomination of trustees, the Council holding the property on trust for car parking and town planning purposes. Due to the absence of a registered easement over the Council’s land, the buyer’s solicitors sought a reduction in the purchase price. The seller would not agree to this. Finally the sale was completed with the buyer reserving its rights to seek compensation.

Turbulent velocity and suspended sediment concentration measurements in an urban environment of the Brisbane River Flood Plain at Gardens Point on 12-13 January 2011

The flood flow in urbanised areas constitutes a major hazard to the population and infrastructure as seen during the summer 2010-2011 floods in Queensland (Australia). Flood flows in urban environments have been studied relatively recently, although no study considered the impact of turbulence in the flow. During the 12-13 January 2011 flood of the Brisbane River, some turbulence measurements were conducted in an inundated urban environment in Gardens Point Road next to Brisbane's central business district (CBD) at relatively high frequency (50 Hz). The properties of the sediment flood deposits were characterised and the acoustic Doppler velocimeter unit was calibrated to obtain both instantaneous velocity components and suspended sediment concentration in the same sampling volume with the same temporal resolution. While the flow motion in Gardens Point Road was subcritical, the water elevations and velocities fluctuated with a distinctive period between 50 and 80 s. The low frequency fluctuations were linked with some local topographic effects: i.e, some local choke induced by an upstream constriction between stairwells caused some slow oscillations with a period close to the natural sloshing period of the car park. The instantaneous velocity data were analysed using a triple decomposition, and the same triple decomposition was applied to the water depth, velocity flux, suspended sediment concentration and suspended sediment flux data. The velocity fluctuation data showed a large energy component in the slow fluctuation range. For the first two tests at z = 0.35 m, the turbulence data suggested some isotropy. At z = 0.083 m, on the other hand, the findings indicated some flow anisotropy. The suspended sediment concentration (SSC) data presented a general trend with increasing SSC for decreasing water depth. During a test (T4), some long -period oscillations were observed with a period about 18 minutes. The cause of these oscillations remains unknown to the authors. The last test (T5) took place in very shallow waters and high suspended sediment concentrations. It is suggested that the flow in the car park was disconnected from the main channel. Overall the flow conditions at the sampling sites corresponded to a specific momentum between 0.2 to 0.4 m2 which would be near the upper end of the scale for safe evacuation of individuals in flooded areas. But the authors do not believe the evacuation of individuals in Gardens Point Road would have been safe because of the intense water surges and flow turbulence. More generally any criterion for safe evacuation solely based upon the flow velocity, water depth or specific momentum cannot account for the hazards caused by the flow turbulence, water depth fluctuations and water surges.

Autonomous movement-driven place recognition calibration for generic multi-sensor robot platforms

In this paper we present a method for autonomously tuning the threshold between learning and recognizing a place in the world, based on both how the rodent brain is thought to process and calibrate multisensory data and the pivoting movement behaviour that rodents perform in doing so. The approach makes no assumptions about the number and type of sensors, the robot platform, or the environment, relying only on the ability of a robot to perform two revolutions on the spot. In addition, it self-assesses the quality of the tuning process in order to identify situations in which tuning may have failed. We demonstrate the autonomous movement-driven threshold tuning on a Pioneer 3DX robot in eight locations spread over an office environment and a building car park, and then evaluate the mapping capability of the system on journeys through these environments. The system is able to pick a place recognition threshold that enables successful environment mapping in six of the eight locations while also autonomously flagging the tuning failure in the remaining two locations. We discuss how the method, in combination with parallel work on autonomous weighting of individual sensors, moves the parameter dependent RatSLAM system significantly closer to sensor, platform and environment agnostic operation.

Mothers influencing mothers : the use of virtual discussion boards and their influence on consumption

Mothers represent a large segment of marketing dollars and traditionally, word of mouth was spread from mother to mother in a face-to-face environment, such as the school car park or mother’s groups. As families have evolved, so too has the traditional mother’s group. Limited academic studies have explored online mothers’ groups and how they impact on consumption. In order to explore the nature of this online influence and how mothers are influenced by other mothers online, a study was conducted through the use of observation and qualitative questioning. The data suggests that trust between mothers is generally high and mothers tend to trust the opinions of other mothers when they recommend a product. This is similar in other reference group contexts, however, mothers are communicating about brands frequently and influencing behaviour. This leads to a number of managerial and theoretical implications discussed in the paper.

Fiber Bragg Grating Sensor Instrumentation for Parking Space Occupancy Management

This work aims at providing an effective parking management system by reducing the drivers' searching time for vacant car-parking space, in turn improving the traffic flow in the car park areas. This is achieved by the use of Fiber Bragg Grating Sensor (FBG) sensor instrumentation in vehicle parking management system. Present work involves embedding an array of FBG sensors underground in the parking space, then determining the strain changes on the FBG sensor due to load applied by the vehicle parked in the parking space, occupancy of the parking space is determined. To validate the FBG sensor parking management system, three most common cases have been considered. This closed loop FBG parking management system can give real-time feed-back to space-guidance display board helping the driver in maneuvering the vehicle to the appropriate parking space. The proposed technique offers optimized usage of parking space for the various segments of cars and also facilitates in a conjoined automated billing system, as compared to conventional method of parking systems.

Fate and transport of volatile organic compounds in glacial till and groundwater at an industrial site in Northern Ireland

Volatile organic compound (VOC) contamination of subsurface geological material and groundwater was discovered on the Nortel Monkstown industrial site, Belfast, Northern Ireland. The objectives of this study were to (1) investigate the characteristics of the geological material and its influences on contaminated groundwater flow across the site using borehole logs and hydrological evaluations, and (2) identify the contaminants and examine their distribution in the subsurface geological material and groundwater using chemical analysis. This report focuses on the eastern car park (ECP) which was a former storage area associated with trichloroethene (TCE) degreasing operations. This is where the greatest amount of volatile organic compounds (VOCs), particularly TCE, were detected. The study site is on a complex deposit of clayey glacial till with discontinuous coarser grained lenses, mainly silts, sands and gravel, which occur at 0.45–7.82 m below ground level (bgl). The lenses overall form an elongated formation that acts as a small unconfined shallow aquifer. There is a continuous low permeable stiff clayey till layer beneath the lenses that performs as an aquitard to the groundwater. Highest concentrations of VOCs, mainly TCE, in the geological material and groundwater are in these coarser lenses at ~4.5–7 m bgl. Highest TCE measurements at 390,000 µg L-1 for groundwater and at 39,000 µg kg-1 at 5.7 m for geological material were in borehole GA19 in the coarse lens zone. It is assumed that TCE gained entrance to the subsurface near this borehole where the clayey till was thin to absent above coarse lenses which provided little retardation to the vertical migration of this dense non-aqueous phase liquid (DNAPL) into the groundwater. However, TCE is present in low concentrations in the geological material overlying the coarse lens zone. Additionally, VOCs appear to be associated with poorly drained layers and in peat

Understanding urban freight activity: key issues for freight planning

Using information gathered from some 30 UK surveys undertaken over the last 15 years, this paper provides planners with an understanding of road-based urban retail freight transport activity. The findings suggest that the average High Street business could expect up to 10 core goods and 7.6 service visits per week, in non-peak trading periods with 25% additional activity during the build up to Christmas. Vans (‘light goods vehicles’) were the dominant mode, responsible for 42% of delivery activity with a mean dwell time of 10 min. Where possible, load consolidation should be encouraged by methods such as Delivery and Servicing Plans and using out-of-town freight consolidation centres to bring in goods over the last mile in shared vehicles. Where this is not possible, loading bay monitoring and control, and preferred lorry routes can help manage the movement of vehicles in and out of dense urban areas. Service vehicle activity is a significant contributor to urban freight movements and often requires vehicles to be parked close to the premises being served. Centrally coordinating elements of service provision (e.g. for cleaning, equipment maintenance, recyclate collection), or providing improved, more flexible parking provision for service vehicles could be as or more beneficial in reducing overall freight impacts than focusing on core goods deliveries. In the case of the latter, ‘pay-as-you-leave’ car park charging systems could encourage short-stay service vehicles to park off-street.

Simulação de sistema de desenfumagem de parques de estacionamento recorrendo ao programa OpenFOAM

Os parques de estacionamento cobertos estão obrigados por legislação a terem sistemas de desenfumagem. Assim, nesta dissertação desenvolve-se um procedimento computacional para a analise e verificação de funcionamento de sistemas de desenfumagem com ventiladores de impulso para parques de estacionamento, recorrendo ao software de mecânica dos fluidos computacional OpenFOAM. Actualmente nos sistemas de desenfumagem de parques de estacionamento estão a ser aplicados ventiladores de impulso. Este tipo de ventiladores não estão contemplados pela legislação em vigor. Assim, para serem utilizados é necessário verificar se estes podem substituir as redes de condutas. A verificação do funcionamento de sistemas de desenfumagem com ventiladores de impulso e efectuada com recurso a programas de simulação de mecânica dos fluidos computacional. O software OpenFOAM não tem tutoriais para ventiladores de impulso. Assim, foi executado um procedimento para validação dos ventiladores de impulso. A validação consistiu em reproduzir-se uma experiência executada por Giesen et al. (2011). Executaram-se várias simulações com diferentes modelos de turbulência, verificando-se que o programa buoyantpimplefoam do software OpenFOAM ao utilizar o modelo de turbulência k -ɛ simulou quase na perfeição os ventiladores de impulso. O desenvolvimento do procedimento computacional foi executado para um parque de estacionamento com uma geometria bastante complexa. O parque de estacionamento foi criado com um software em 3D e posteriormente inserido numa malha j a criada com as dimensões exteriores do parque. Foram estipuladas as condições de fronteira e executou-se uma simulação de seiscentos segundos com parâmetros determinados previamente. O processamento da simulação teve a duração de aproximadamente oito dias. Dos resultados obtidos concluiu-se que o procedimento computacional apresentado simula adequadamente sistemas de desenfumagem em parques de estacionamento.