Oil Retention and Pressure Drop in Horizontal and Vertical Suction Lines with R410A / POE ISO 32

In refrigeration systems a small amount of compressor lubricant is entrained in the refrigerant and circulated through the system, where some is retained in each component. The suction line to the compressor has the largest potential for oil retention. This paper presents results from an experimental apparatus that has been constructed to circulate POE (polyolester) oil and R410A at a controlled mass flux, OCR (oil in circulation ratio), and apparent superheat, and to directly measure the pressure drop and mass of oil retained in horizontal and vertical suction lines. The bulk vapor velocity and overall void fraction are determined from direct mass and temperature measurements. The oil retention, pressure drop, and flow regimes near the minimum ASHRAE recommended mass flux condition are explored. It was found that oil retention begins to increase sharply even above the minimum recommended flux, so conditions near the minimum should be avoided. Two relationships were developed to predict the oil retention in the vertical and horizontal suction lines. The average error from the predictions method was 10.9% for the vertical tube, and 7.9% for the horizontal tube.

Crude oil and agricultural futures: An analysis of correlation dynamics

Correlations between oil and agricultural commodities have varied over previous decades, impacted by renewable fuels policy and turbulent economic conditions. We estimate smooth transition conditional correlation models for 12 agricultural commodities and WTI crude oil. While a structural change in correlations occurred concurrently with the introduction of biofuel policy, oil and food price levels are also key influences. High correlation between biofuel feedstocks and oil is more likely to occur when food and oil price levels are high. Correlation with oil returns is strong for biofuel feedstocks, unlike with other agricultural futures, suggesting limited contagion from energy to food markets.

Synthesis of new vegetable oil-based polymeric materials

A crescente procura de recursos fosseis a que se tem assistido nos ultimos anos, tem resultado num crescimento sem precedentes dos precos, com consequencias imprevisiveis e que levara, no espaco de decadas, ao seu inevitavel esgotamento. A procura de um modelo de desenvolvimento sustentavel, baseado em recursos renovaveis e o grande desafio que se coloca a civilizacao no seculo XXI. A biomassa vegetal, atraves das designadas gBio-refinarias h, e uma alternativa logica para a producao de produtos quimicos e de materiais mas tambem de combustiveis e energia. Os oleos vegetais constituem uma das fracoes da biomassa vegetal, cuja exploracao tem merecido redobrada atencao nos ultimos anos, como fonte de materiais e de combustiveis. Assim, a presente dissertacao tem por objetivo o desenvolvimento de novos materiais polimericos derivados de oleos vegetais, seguindo duas abordagens distintas, nomeadamente a preparacao de polimeros atraves de polimerizacao por etapas e polimerizacao em cadeia (Parte B e C, respetivamente). Em primeiro lugar, foram sintetizados poliesteres alifaticos de cadeia longa a partir de monomeros provenientes do oleo de colza (Capitulo III). A auto-metatese do acido erucico com catalisadores de rutenio, seguida de hidrogenacao da ligacao dupla, originou o acido 1,26-hexacosanodioico, que por sua vez foi convertido em hexacosano-1,26-diol. Subsequentemente, a policondensacao do acido ƒ¿,ƒÖ-dicarboxilico de cadeia longa com o hexacosano-1,26-diol originou o poliester 26,26. O diacido C26 foi tambem polimerizado com outros alcano-diois de cadeia curta, nomeadamente o dodecano-1,12-diol e o butano-1,2-diol, produzindo, respetivamente, os poliesteres 12,26 e 4,26. Estes poliesteres de fontes 100% renovaveis possuem valores de Mn na ordem dos 8-14 kDa e valores de PDI entre 2.1 e 2.7. As propriedades destes poliesteres alifaticos foram avaliadas atraves de varias tecnicas, revelando elevada cristalinidade (com uma estrutura cristalina como a do polietileno) e elevadas temperaturas de fusao (74-104 ‹C), cristalizacao (68-92 ‹C) e degradacao (323-386 ‹C). Em segundo lugar, foram sintetizados polimeros lineares termo-reversiveis a partir de derivados do oleo de ricinio (Capitulo IV). Para tal foram preparados monomeros que incorporam aneis furanicos inseridos atraves do acoplamento tiol-eno, e que posteriormente foram polimerizados pela reacao de Diels-Alder (DA) entre os grupos furano (dieno A) e estruturas complementares do tipo maleimida (dienofilo B). Para as polimerizacoes DA foram consideradas duas abordagens diferentes, nomeadamente (i) o uso de monomeros com dois aneis furanicos terminais em conjunto com uma bismaleimida (sistemas AA+BB) e (ii) a utilizacao de um monomero que incorpora ambos os grupos reativos, furano e maleimida, na sua estrutura (sistema AB). Este estudo demonstrou claramente que ambas as estratégias foram bem sucedidas embora com diferentes resultados em termos da natureza dos produtos obtidos. Estes polímeros lineares apresentam valores relativamente baixos de Tg (-40 to -2 °C) devido à natureza flexível dos grupos separadores das funções reativas, e de Mn (4.5-9.0 kDa) dada a observada tendência de ciclização associada a concentrações baixas de monómero. A aplicação da reação de retro-DA aos polímeros em causa confirmou o seu caráter reversível, ou seja, a possibilidade de promover, em condições controladas, a despolimerização com recuperação dos monómeros de partida. Esta particularidade abre caminhos para materiais macromoleculares originais com aplicações promissoras tais como auto-reparação e reciclabilidade. Em terceiro lugar, sintetizaram-se polímeros não-lineares termo-reversíveis a partir de derivados do óleo de ricínio (Capítulo V). Para tal foram preparados monómeros trifuncionais e posteriormente polimerizados através da reação de DA entre os grupos reativos complementares furano/maleimida. Foram consideradas três abordagens distintas para preparar estes polímeros não-lineares, nomeadamente através da utilização de (i) um monómero bisfurânico em combinação com uma trismaleimida (sistema A2+B3) e (ii) um monómero trisfurânico em conjunto com uma bismaleimida (sistema A3+B2) que originaram materiais ramificados ou reticulados, e ainda (iii) a utilização de monómeros assimetricamente substituídos do tipo A2B ou AB2 capazes de originar estruturas macromoleculares hiper-ramificadas. Todos os sistemas apresentaram valores de Tg perto de 0 °C, o que era de esperar para estes materiais não-lineares. A aplicação da reação de retro-DA comprovou mais uma vez o caráter termo-reversível das polimerizações em causa. Em quarto lugar e último lugar, foram preparados copolímeros de acetato de vinilo (VAc) com monómeros derivados de óleo de girassol (Capítulo VI). Ésteres vinílicos de ácidos gordos (FAVE) foram sintetizados por transvinilação dos ácidos oleico e linoleico com VAc catalisada por um complexo de irídio. Os monómeros vinílicos preparados foram caracterizados e posteriormente homopolimerizados e copolimerizados com VAc através do uso dos grupos vinílicos terminais como função inicial de polimerização. A variação do tipo e quantidade de monómero FAVE e da quantidade de iniciador radicalar originou copolímeros de VAc com valores de Mn na gama de 1.2-3.0 kDa e valores de Tg de -5 a 16 °C. Os copolímeros foram avaliados em testes de cura oxidativa através das insaturações nas suas cadeias alifáticas para formar materiais reticulados, e os resultados sugerem que eles podem ser sistemas efetivos de cura para aplicações como tintas, vernizes e outros tipos de revestimento. Todos os materiais poliméricos preparados ao longo deste trabalho constituem contribuições atrativas para a área dos polímeros oriundos de recursos renováveis e representam uma prova indiscutível de que os óleos vegetais são percursores promissores de materiais macromoleculares com potenciais aplicações.

Using artificial neural networks to generate trading signals for crude oil, copper and gold futures

In this thesis, a feed-forward, back-propagating Artificial Neural Network using the gradient descent algorithm is developed to forecast the directional movement of daily returns for WTI, gold and copper futures. Out-of-sample back-test results vary, with some predictive abilities for copper futures but none for either WTI or gold. The best statistically significant hit rate achieved was 57% for copper with an absolute return Sharpe Ratio of 1.25 and a benchmarked Information Ratio of 2.11.

Effects Of The Piscicides, Mahua Oil Cake And Croton Seed On The Prawn Culture System

The present research programme envisages a comparative study of the effects of two piscicides of plant origin, viz., mahua oil cake, a derivative from the plant fig Iatifolia and croton seed, a product from the plant Croton tiglium. Although some reports on the effects of mahua oil cake and croton seed on fresh water pond culture systems are available, information on their effect on brackishwater culture systems are rather scanty This was the guiding principle for launching the present study It is hoped that the findings will enable aquaculturists to make use of the piscicides in a more rational and efficient way, and will go a long way towards realising the maximum return liom culture systems without hampering the environment. The thesis is presented in seven chapters such as Introduction, Review of literature, Materials and Methods, Results, Discussion, Summary and Bibliography

Assessing the date of the global oil peak: the need to use 2P reserves

Combining geological knowledge with proved plus probable ('2P') oil discovery data indicates that over 60 countries are now past their resource-limited peak of conventional oil production. The data show that the global peak of conventional oil production is close. Many analysts who rely only on proved ('1P') oil reserves data draw a very different conclusion. But proved oil reserves contain no information about the true size of discoveries, being variously under-reported, over-reported and not reported. Reliance on 1P data has led to a number of misconceptions, including the notion that past oil forecasts were incorrect, that oil reserves grow very significantly due to technology gain, and that the global supply of oil is ensured provided sufficient investment is forthcoming to 'turn resources into reserves'. These misconceptions have been widely held, including within academia, governments, some oil companies, and organisations such as the IEA. In addition to conventional oil, the world contains large quantities of non-conventional oil. Most current detailed models show that past the conventional oil peak the non-conventional oils are unlikely to come on-stream fast enough to offset conventional's decline. To determine the extent of future oil supply constraints calculations are required to determine fundamental rate limits for the production of non-conventional oils, as well as oil from gas, coal and biomass, and of oil substitution. Such assessments will need to examine technological readiness and lead-times, as well as rate constraints on investment, pollution, and net-energy return. (C) 2007 Elsevier Ltd. All rights reserved.

An intelligent system to detect drilling problems through drilled cuttings return analysis

Cuttings return analysis is an important tool to detect and prevent problems during the petroleum well drilling process. Several measurements and tools have been developed for drilling problems detection, including mud logging, PWD and downhole torque information. Cuttings flow meters were developed in the past to provide information regarding cuttings return at the shale shakers. Their use, however, significantly impact the operation including rig space issues, interferences in geological analysis besides, additional personel required. This article proposes a non intrusive system to analyze the cuttings concentration at the shale shakers, which can indicate problems during drilling process, such as landslide, the collapse of the well borehole walls. Cuttings images are acquired by a high definition camera installed above the shakers and sent to a computer coupled with a data analysis system which aims the quantification and closure of a cuttings material balance in the well surface system domain. No additional people at the rigsite are required to operate the system. Modern Artificial intelligence techniques are used for pattern recognition and data analysis. Techniques include the Optimum-Path Forest (OPF), Artificial Neural Network using Multilayer Perceptrons (ANN-MLP), Support Vector Machines (SVM) and a Bayesian Classifier (BC). Field test results conducted on offshore floating vessels are presented. Results show the robustness of the proposed system, which can be also integrated with other data to improve the efficiency of drilling problems detection. Copyright 2010, IADC/SPE Drilling Conference and Exhibition.

Reversible polymerization of novel monomers bearing furan and plant oil moieties: a double click exploitation of renewable resources

Monomers based on plant oil derivatives bearing furan heterocycles appended through thiol-ene click chemistry were prepared and, subsequently, polymerized via a second type of click reaction, i. e. the Diels-Alder (DA) polycondensation between furan and maleimide complementary moieties. Two basic approaches were considered for these DA polymerizations, namely (i) the use of monomers with two terminal furan rings in conjunction with bismaleimides (AA + BB systems) and (ii) the use of a protected AB monomer incorporating both furan and maleimide end groups. This study clearly showed that both strategies were successful, albeit with different outcomes, in terms of the nature of the ensuing products. The application of the retro-DA reaction to these polymers confirmed their thermoreversible character, i. e. the clean-cut return to their respective starting monomers, opening the way to original macromolecular materials with interesting applications, like mendability and recyclability.

Survival and movements of Magellanic penguins rehabilitated from oil fouling along the coast of South America, 2000-2010

Oil pollution is a significant conservation concern. We examined data from six institutions along the coast of South America: Emergency Relief Team of the International Fund for Animal Welfare, Fundacion Mundo Marino, Centro de Recuperacao de Animais Marinhos, Natura Patagonia, Associacao R3 Animal, and Mar del Plata Aquarium and data from resightings in Argentina, Brazil, Chile and Falkland/Malvinas Islands. From 2000 to 2010, 2183 oiled Magellanic penguins were rehabilitated as part of the routine activities of these institutions or during emergency responses to eight oil spills in which they were involved; all rehabilitated penguins were flipper banded and released. Since their release, 41 penguins were resighted until 31 December 2011. The results demonstrate that, when combined with other prevention strategies, the rehabilitation of Magellanic penguins is a strategy that contributes to the mitigation of adverse effects of oil spills and chronic pollution to the species. (C) 2012 Elsevier Ltd. All rights reserved.

Determinación del riesgo de incendio en una instalación de secado de alperujo = Determination of the risk of fire in an olive-oil mill waste dryer

For the energy valorization of alperujo, residue of the olive oil two phases extraction process, it is necessary to perform a drying process to reduce moisture content from over 60% to less than 10%. In order to reduce primary energy consumption and get an economic return, usually in this kind of drying facilities Gas Turbine CHP is used as a heat source. There have been recently in Spain some fires in this kind of GT-CHP facilities, which have caused high material losses. In some of these fires it has been suggested that the fire was caused by the output of incandescent alperujo in the flue gasesof the drying system. Therefore, the aim of this study is to determine experimentally and analytically under which operational conditions a process of alperujo self-ignition in the drying process can begin, and determine the actual fire hazard in this type of TG-CHP system. For analytical study, the temperature and initial composition of the combustion gases of the Gas Turbine at the entrance of the drying process was calculated and the gas equilibrium conditions reached in contact with the biomass were calculated and, therefore, the temperature of the biomass during the drying process. Moreover, the layer and dust ignition temperature of alperujo has been experimentally determined, according to EN 50281-2-1: 2000. With these results, the operating conditions of the drying process, in which there are real risk of auto-ignition of alperujo have been established.Para la valorización energética del alperujo, residuo del proceso de extracción en dos fases del aceite de oliva, es necesario realizar un proceso de secado para reducir su contenido de humedad de más del 60% al 10% m/m en b.h. Con el fin de reducir el consumo de energía primaria y obtener una rentabilidad económica, normalmente en este tipo de instalaciones de secado se usa la cogeneración con turbina de gas (TG) como fuente de calor. En España en los últimos años han ocurrido algunos casos de incendio en este tipo de instalaciones de cogeneración, que han supuesto pérdidas materiales muy elevadas. Por esta razón, el objetivo de este trabajo es determinar analítica y experimentalmente las condiciones operativas del secadero bajo las cuales podría comenzar un proceso de autoinflamación del alperujo y determinar el riesgo real de incendio en este tipo de instalaciones. Para el estudio analítico, se ha planteado y validado el modelo matemático que permite calcular la temperatura y la composición de los gases de combustión a la entrada y a la salida del secadero, en función de las curvas características de la TG, de las condiciones atmosféricas, del caudal y del grado de humedad de la biomasa tratada. El modelo permite además calcular la temperatura de bulbo húmedo, que es la máxima temperatura que podría alcanzar la biomasa durante el proceso de secado y determinar la cantidad de biomasa que se puede secar completamente en función del caudal y de las condiciones de entrada de los gases de combustión. Con estos resultados y la temperatura mínima de autoinflamación del alperujo determinada experimentalmente siguiendo la norma EN 50281- 2-1:2000, se demuestra que en un proceso de secado de alperujo en condiciones normales de operación no existe riesgo de autoencendido que pueda dar origen a un incendio.

Return of the Herd: houses at upper left

Pieter Bruegel the Elder; oil on wood

ECONOMIC PROFITABILITY OF THE BAKKEN, NORTH DAKOTA UNCONVENTIONAL OIL PLAYS BASED ON A TYPICAL WELL PERFORMANCE WITH CURRENT MARKET CONDITIONS

Increases in oil prices after the economic recession have been surprising for domestic oil production in the United States since the beginning of 2009. Not only did the conventional oil extraction increase, but unconventional oil production and exploration also improved greatly with the favorable economic conditions. This favorable economy encourages companies to invest in new reservoirs and technological developments. Recently, enhanced drilling techniques including hydraulic fracturing and horizontal drilling have been supporting the domestic economy by way of unconventional shale and tight oil from various U.S. locations. One of the main contributors to this oil boom is the unconventional oil production from the North Dakota Bakken field. Horizontal drilling has increased oil production in the Bakken field, but the economic issues of unconventional oil extraction are still debatable due to volatile oil prices, high decline rates of production, a limited production period, high production costs, and lack of transportation. The economic profitability and viability of the unconventional oil play in the North Dakota Bakken was tested with an economic analysis of average Bakken unconventional well features. Scenario analysis demonstrated that a typical North Dakota Bakken unconventional oil well is profitable and viable as shown by three financial metrics; net present value, internal rate of return, and break-even prices.