An analysis of the relationship between grain size, solute content, and the potency and number density of nucleant particles

To be able to determine the grain size obtained from the addition of a grain refining master alloy, the relationship between grain size (d), solute content (defined by the growth restriction factor Q), and the potency and number density of nucleant particles needs to be understood. A study was undertaken on aluminium alloys where additions of TiB2 and Ti were made to eight wrought aluminum alloys covering a range of alloying elements and compositions. It was found from analysis of the data that d = a/(3)root pct TiB2 + b/Q. From consideration of the experimental data and from further analysis of previously published data, it is shown that the coefficients a and b relate to characteristics of the nucleant particles added by a grain refiner. The term a is related to the maximum density of active TiB2 nucleant particles within the melt, while b is related to their potency. By using the analysis methodology presented in this article, the performance characteristics of different master alloys were defined and the effects of Zr and Si on the poisoning of grain refinement were illustrated.

Aluminium alloys - their physical and mechanical properties: Grain formation in AlSi7Mg0.35 foundry alloy at low superheat

Hypoeutectic AI-Si alloys represent the most widely used alloy system for cast aluminium applications. This system has a unique behaviour with respect to grain formation where an increase in silicon content results in a transition to larger grain sizes after a minimum at an intermediate concentration. As a result of the already large solute content, grain refinement by solute additions is inefficient and nucleant particles from the common aluminium grain refiners are not as effective as in wrought alloys. However, casting conditions, such as a low pouring temperature, that promote the formation of wall crystals tie. crystals nucleated in the thermally undercooled layer at or next to mould walls) are very effective in yielding a small grain size. This paper presents results of an investigation of the effect of low superheat and mould preheat temperature on grain size. It was found that pouring temperature controls the effectiveness of the wall mechanism while mould preheat has little effect until high preheat temperatures at which a large increase in grain size occurs. The observed changes in grain size are explained in terms of the balance between nucleation rate and survival rate of crystal nuclei resulting from changes in superheat and mould temperature.

Using gold nanoparticles in protein crystallography: studies in crystal growth and derivatization

Dissertation for the Master Degree in Structural and Functional Biochemistry

Thickening of phase change materials (PCM) to avoid segregation

Estudi elaborat a partir d’una estada a Çukurova University, Turquia, al juliol del 2006. L’emmagatzematge d’energia tèrmica ha atret interès en aplicacions tèrmiques com l’aigua calenta, la calefacció i l’aire condicionat. Aquests sistemes són útils per corregir la no coincidència entre la oferta i la demanda d’energia. Principalment hi ha dos tipus de sistemes d’emmagatzematge d’energia tèrmica, emmagatzematge amb calor sensible i amb calor latent. L’emmagatzematge amb calor latent és particularment atractiu degut a la seva habilitat de donar una densitat d’emmagatzematge d’energia més alt i la seva característica d’emmagatzemar calor a una temperatura constant corresponent a la temperatura de transició de fase de la substància emmagatzemadora de calor. Les salts hidratades orgàniques tenen certes avantatges com a materials d’emmagatzematge de calor latent sobre els materials orgànics. En canvi, quan les salts hidratades s’utilitzen com a materials de canvi de fase (PCM) apareixen alguns problemes en les aplicacions d’emmagatzematge de calor latent. Aquests són el subrefredament de les salts hidratades quan es congelen degut a les seves dèbils propietats de nucleació, i la separació de fase que hi apareix degut a una fusió incongruent. En aquest estudi, s’estabilitza sal de Glauber (Na2SO4.10H2O) amb diferents concentracions de poliacrilamida i gelatina per prevenir la fusió incongruent. Per prevenir el subrefredament s’utilitza un agent nucleant amb una estructura cristal•lina semblant a la de la sal de Glauber. La capacitat d’emmagatzematge de calor de les mostres de PCM estabilitzades amb diferents concentracions de gels polimèrics es determinen amb DCS i amb el mètode T-history.

Grain refinement of Mg-Al(-Mn) alloys by SiC additions

The addition of SiC particles effectively grain refined a range of Mg-Al alloys. The greatest reductions in grain size were found for the alloys with lower Al contents. The presence of Mg2Si in the microstructure after that SiC addition, and consideration of phase equilibria suggested that the SiC transforms to Al4C3, and this is the actual nucleant. The addition of Mn poisoned the grain refining effect of the SiC addition, probably due to the formation of less potent Al-Mn-carbides. (c) 2006 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.