A dose-response curve for biodosimetry from a 6 MV electron linear accelerator

Biological dosimetry (biodosimetry) is based on the investigation of radiation-induced biological effects (biomarkers), mainly dicentric chromosomes, in order to correlate them with radiation dose. To interpret the dicentric score in terms of absorbed dose, a calibration curve is needed. Each curve should be constructed with respect to basic physical parameters, such as the type of ionizing radiation characterized by low or high linear energy transfer (LET) and dose rate. This study was designed to obtain dose calibration curves by scoring of dicentric chromosomes in peripheral blood lymphocytes irradiated in vitro with a 6 MV electron linear accelerator (Mevatron M, Siemens, USA). Two software programs, CABAS (Chromosomal Aberration Calculation Software) and Dose Estimate, were used to generate the curve. The two software programs are discussed; the results obtained were compared with each other and with other published low LET radiation curves. Both software programs resulted in identical linear and quadratic terms for the curve presented here, which was in good agreement with published curves for similar radiation quality and dose rates.

Dose-response curve to soil applied herbicides and susceptibility evaluation of different amaranthus species using model identity

Greenhouse studies were conducted in 2008-2009 with the objective of adjusting dose-response curves of the main soil-applied herbicides currently used in cotton for the control of Amaranthus viridis, A. hybridus, A. spinosus, A. lividus, as well as comparing susceptibility among different species, using the identity test models. Thirty six individual experiments were simultaneously carried out in greenhouse, in a sandy clay loam soil (21% clay, 2.36% OM) combining increasing doses of the herbicides alachlor, clomazone, diuron, oxyfluorfen, pendimethalin, prometryn, S-metolachlor, and trifluralin applied to each species. Dose-response curves were adjusted for visual weed control at 28 days after herbicide application and doses required for 80% (C80) and 95% (C95) control were calculated. All herbicides, except clomazone and trifluralin, provided efficient control of most Amaranthus species, but substantial differences in susceptibility to herbicides were found. In general, A. lividus was the least sensitive species, whereas A. spinosus demonstrated the highest sensitivity to herbicides. Alachlor, diuron, oxyfluorfen, pendimethalin, S-metolachlor, and prometryn are efficient alternatives to control Amaranthus spp. in a range of doses that are currently lower than those recommended to cotton.

CRASH: a computer simulator of non-linear transient response of structures, basis for car crash simulation. Research report.

National Highway Traffic Safety Administration, Washington, D.C.

Non-linear temperature response of Bragg gratings in doped and un-doped holey polymer optical fibre

We present measurements on the non-linear temperature response of fibre Bragg gratings recorded in pure and trans-4-stilbenemethanol-doped polymethyl methacrylate (PMMA) holey fibres.

Non-linear temperature response of Bragg gratings in doped and un-doped holey polymer optical fibre

We present measurements on the non-linear temperature response of fibre Bragg gratings recorded in pure and trans-4-stilbenemethanol-doped polymethyl methacrylate (PMMA) holey fibres.

Two-Path All-pass Based Half-Band Infinite Impulse Response Decimation Filters and the Effects of Their Non-Linear Phase Response on ECG Signal Acquisition

This paper is based on the novel use of a very high fidelity decimation filter chain for Electrocardiogram (ECG) signal acquisition and data conversion. The multiplier-free and multi-stage structure of the proposed filters lower the power dissipation while minimizing the circuit area which are crucial design constraints to the wireless noninvasive wearable health monitoring products due to the scarce operational resources in their electronic implementation. The decimation ratio of the presented filter is 128, working in tandem with a 1-bit 3rd order Sigma Delta (ΣΔ) modulator which achieves 0.04 dB passband ripples and -74 dB stopband attenuation. The work reported here investigates the non-linear phase effects of the proposed decimation filters on the ECG signal by carrying out a comparative study after phase correction. It concludes that the enhanced phase linearity is not crucial for ECG acquisition and data conversion applications since the signal distortion of the acquired signal, due to phase non-linearity, is insignificant for both original and phase compensated filters. To the best of the authors’ knowledge, being free of signal distortion is essential as this might lead to misdiagnosis as stated in the state of the art. This article demonstrates that with their minimal power consumption and minimal signal distortion features, the proposed decimation filters can effectively be employed in biosignal data processing units.

Évaluation de la fréquence des micronoyaux et du potentiel clastogène et/ou aneugène du benzo-a-pyrène suite à une exposition in vitro des lymphocytes humains

Le benzo-a-pyrène (BaP) est un cancérogène reconnu pour l'homme, contaminant présent dans notre environnement. Il cause des dommages à l'ADN que nous avons mesurés dans les lymphocytes exposés à de faibles concentrations de BaP, provenant de 20 jeunes volontaires non fumeurs et en santé. Suite à l’exposition, la fréquence des micronoyaux (MN) augmente significativement et décrit une courbe dose-réponse non linéaire, suggérant le déclenchement du processus de détoxification et la réparation de l’ADN. Des différences entre les individus et entre les sexes sont présentes dans la réponse génotoxique produite par le BaP. Le test des aberrations chromosomiques montre que le pourcentage de chromosomes cassés augmente significativement dans les cellules exposées au BaP. Combinés avec l'augmentation de la fréquence des MN, nos résultats confirment l'effet clastogène du BaP déjà rapporté dans la littérature. L’hybridation in situ en fluorescence (FISH) des MN avec une sonde pancentromérique est aussi utilisée pour établir leur mécanisme de formation. La FISH révèle que la majorité des MN formés après une exposition au BaP contient un centromère et plus, ce qui est significativement différent de la condition non exposée. Plus précisément, dans nos conditions expérimentales, les MN induits par le BaP contiennent surtout trois centromères et plus, indiquant également la présence d'un effet aneugène. L'effet clastogène du BaP est relié à son rôle d'initiateur dans la cancérogenèse, alors que l'effet aneugène le relierait à l'étape de progression. Ces résultats sont importants puisque l'exposition aux composés de la classe du BaP est de longue durée (cigarette, air pollué).

EGFR inhibitors erlotinib and lapatinib ameliorate epidermal blistering in pemphigus vulgaris in a non-linear, V-shaped relationship.

Novel insights into intra-cellular signalling involved in pemphigus vulgaris (PV), an autoimmune blistering disease of skin and mucous membranes, are now revealing new therapeutic approaches such as the chemical inhibition of PV-associated signals in conjunction with standard immunosuppressive therapy. However, extensive inhibition of signalling molecules that are required for normal tissue function and integrity may hamper this approach. Using a neonatal PV mouse model, we demonstrate that epidermal blistering can be prevented in a dose-dependent manner by clinically approved EGFR inhibitors erlotinib and lapatinib, but only up to approximately 50% of normal EGFR activity. At lower EGFR activity, blisters again aggravated and were highly exacerbated in mice with a conditional deletion of EGFR. Statistical analysis of the relation between EGFR activity and the extent of skin blistering revealed the best fit with a non-linear, V-shaped curve with a median break point at 52% EGFR activity (P = 0.0005). Moreover, lapatinib (a dual EGFR/ErbB2 inhibitor) but not erlotinib significantly reduced blistering in the oral cavity, suggesting that signalling mechanisms differ between PV predilection sites. Our results demonstrate that future clinical trials evaluating EGFR/ErbB2 inhibitors in PV patients must select treatment doses that retain a specific level of signal molecule activity. These findings may also be of relevance for cancer patients treated with EGFR inhibitors, for whom skin lesions due to extensive EGFR inhibition represent a major threat.

Statnote 19: non-linear regression: fitting an exponential curve to data

Non-linear relationships are common in microbiological research and often necessitate the use of the statistical techniques of non-linear regression or curve fitting. In some circumstances, the investigator may wish to fit an exponential model to the data, i.e., to test the hypothesis that a quantity Y either increases or decays exponentially with increasing X. This type of model is straight forward to fit as taking logarithms of the Y variable linearises the relationship which can then be treated by the methods of linear regression.

Methacholine Dose-Response Slopes from Maximal Bronchial Challenge Tests in Asthmatic Children: Methodological Aspects

To determine whether the slope of a maximal bronchial challenge test (in which FEV1 falls by over 50%) could be extrapolated from a standard bronchial challenge test (in which FEV1 falls up to 20%), 14 asthmatic children performed a single maximal bronchial challenge test with methacholin(dose range: 0.097–30.08 umol) by the dosimeter method. Maximal dose-response curves were included according to the following criteria: (1) at least one more dose beyond a FEV1 ù 20%; and (2) a MFEV1 ù 50%. PD20 FEV1 was calculated, and the slopes of the early part of the dose-response curve (standard dose-response slopes) and of the entire curve (maximal dose-response slopes) were calculated by two methods: the two-point slope (DRR) and the least squares method (LSS) in % FEV1 × umol−1. Maximal dose-response slopes were compared with the corresponding standard dose-response slopes by a paired Student’s t test after logarithmic transformation of the data; the goodness of fit of the LSS was also determined. Maximal dose-response slopes were significantly different (p < 0.0001) from those calculated on the early part of the curve: DRR20% (91.2 ± 2.7 FEV1% z umol−1)was 2.88 times higher than DRR50% (31.6 ± 3.4 DFEV1% z umol−1), and the LSS20% (89.1 ± 2.8% FEV1 z umol−1) was 3.10 times higher than LSS 50% (28.8 ± 1.5%FEV1 z umol−1). The goodness of fit of LSS 50% was significant in all cases, whereas LSS 20% failed to be significant in one. These results suggest that maximal dose-response slopes cannot be predicted from the data of standard bronchial challenge tests.

Évaluation de la cytogénotoxicité humaine induite par l’exposition à de faibles doses de benzo-a-pyrène, à l’aide de biomarqueurs précoces

Le benzo-a-pyrène (BaP) est un hydrocarbure aromatique polycyclique (HAP) cancérogène pour l’homme, qui contamine toutes les sphères de notre environnement. Son métabolite, le BaP-7,8-diol-9,10-époxyde (BPDE) est considéré comme son cancérogène ultime. Le BPDE se lie à l’ADN, formant des adduits qui doivent être réparés et qui seraient responsables des dommages à l’ADN et de la cancérogenèse induite par le BaP. Les adduits BPDE-ADN et les dommages à l’ADN (bris simple-brin [BSB] à l’ADN, aberrations chromosomiques [AC], échanges entre chromatides-sœurs [ÉCS] et micronoyaux [MN]) ont été mesurés dans les lymphocytes humains exposés à de faibles concentrations de BaP, provenant de jeunes volontaires non-fumeurs et en santé. Suite à l’exposition au BaP, le niveau d’adduits BPDE-ADN et la fréquence des AC et des MN augmentent significativement, puis diminuent aux concentrations les plus élevées de BaP testées, suggérant une induction du métabolisme de phase II du BaP. Lors de la mesure des ÉCS, nous obtenons une courbe dose-réponse linéaire, indiquant la production d’un autre type de lésions devant être réparées par le système de réparation par recombinaison homologue. Ces lésions pourraient être des bris à l’ADN ou des bases oxydées (8-OH-dG), ce qui est suggéré par l’analyse des corrélations existant entre nos biomarqueurs. Par ailleurs, la comparaison de la courbe dose-réponse des hommes et des femmes montre que des différences existent entre les sexes. Ainsi, les ÉCS, les AC et les MN sont significativement augmentés chez les hommes à la plus faible concentration de BaP, alors que chez les femmes cette augmentation, quoique présente, est non significative. Des différences interindividuelles sont également observées et sont plus importantes pour les adduits BPDE-ADN, les MN et les AC, alors que pour les ÉCS elles sont minimes. Les analyses statistiques effectuées ont permis d’établir que quatre facteurs (niveau d’exposition au BaP, adduits BPDE-ADN, fréquence des AC et nombre de MN par cellule micronucléée) expliquent jusqu’à 59 % de la variabilité observée dans le test des ÉCS, alors qu’aucun facteur significatif n’a pu être identifié dans le test des AC et des MN. L’analyse du mécanisme de formation de nos biomarqueurs précoces permet de suggérer que les bris à l’ADN et les bases oxydées devraient être classées comme biomarqueurs de dose biologique efficace, au sein des biomarqueurs d’exposition, dans le continuum exposition-maladie du BaP, étant donné qu’ils causent la formation des biomarqueurs de génotoxicité (ÉCS, AC et MN). Par ailleurs, le test des AC et des MN ont permis de confirmer l’action clastogénique du BaP en plus de mettre en évidence des effets aneugènes affectant surtout la ségrégation des chromosomes lors de la division cellulaire. Ces effets aneugènes, reliés à l’étape de progression dans la cancérogenèse, pourraient être particulièrement importants puisque l’exposition au BaP et aux HAP est chronique et dure plusieurs années, voire des décennies. La compréhension des mécanismes régissant la formation des biomarqueurs étudiés dans cette étude, ainsi que des relations existant entre eux, peut être appliquée à de nombreux contaminants connus et émergents de notre environnement et contribuer à en évaluer le mode d’action.

Design and Synthesis of Donor-Acceptor Low Band Gap Copolymers for Photoconductive and Non-linear Optical Applications

The main focus of the present study was to develop ideal low band gap D-A copolymers for photoconducting and non-linear optical applications. This chapter summarizes the overall research work done. Designed copolymers were synthesized via direct arylation or Suzuki coupling reactions. Copolymers were characterized by theoretical and experimental methods. The suitability of these copolymers in photoconducting and optical limiting devices has been investigated.The results suggest that the copolymers investigated in the present study have a good non-linear optical response and are comparable to or even better than the D-A copolymers reported in the literature and hence could be chosen as ideal candidates with potential applications for non-linear optics. The results also show that the structures of the polymers have great impact on NLO properties. Copolymers studied here exhibits good optical limiting property at 532 nm wavelength due to two-photon absorption (TPA) process. The results revealed that the two copolymers, (P(EDOT-BTSe) and P(PH-TZ)) exhibited strong two-photon absorption and superior optical power limiting properties, which are much better than that of others.

Non-Linear Dielectric Properties of PLMN-PT Relaxor Ferroelectrics

Recent investigations on the non-linear (NL) dielectric properties of relaxor ferroelectrics systems, not only as ceramic bodies, but also, in thin films, have showed a significant technological and scientific interest. The most common practical applications of relaxors include multilayer capacitors and actuators. In this work, non-linear dielectric properties of hot-pressed (1-x)[Pb1 -(3/2) yLayMg1/3Nb2/3O3]-xPbTiO3 (PLMN-PT) ferroelectric ceramics were investigated. The NL properties were obtained by using the measurements of the dielectric permittivity of the material as a function of the AC electric field with variable amplitude in the frequency and temperature range of 100 Hz-1 MHz and 50-450 K, respectively. An anomalous behavior of the non-linear dielectric response was observed when submitted to high electric fields levels. The obtained results were analyzed concerning one of the models for the dielectric response of relaxors ferroelectrics materials currently discussed in the literature.

Copper and human health: biochemistry, genetics, and strategies for modeling dose-response relationships

Copper (Cu) and its alloys are used extensively in domestic and industrial applications. Cu is also an essential element in mammalian nutrition. Since both copper deficiency and copper excess produce adverse health effects, the dose-response curve is U-shaped, although the precise form has not yet been well characterized. Many animal and human studies were conducted on copper to provide a rich database from which data suitable for modeling the dose-response relationship for copper may be extracted. Possible dose-response modeling strategies are considered in this review, including those based on the benchmark dose and categorical regression. The usefulness of biologically based dose-response modeling techniques in understanding copper toxicity was difficult to assess at this time since the mechanisms underlying copper-induced toxicity have yet to be fully elucidated. A dose-response modeling strategy for copper toxicity was proposed associated with both deficiency and excess. This modeling strategy was applied to multiple studies of copper-induced toxicity, standardized with respect to severity of adverse health outcomes and selected on the basis of criteria reflecting the quality and relevance of individual studies. The use of a comprehensive database on copper-induced toxicity is essential for dose-response modeling since there is insufficient information in any single study to adequately characterize copper dose-response relationships. The dose-response modeling strategy envisioned here is designed to determine whether the existing toxicity data for copper excess or deficiency may be effectively utilized in defining the limits of the homeostatic range in humans and other species. By considering alternative techniques for determining a point of departure and low-dose extrapolation (including categorical regression, the benchmark dose, and identification of observed no-effect levels) this strategy will identify which techniques are most suitable for this purpose. This analysis also serves to identify areas in which additional data are needed to better define the characteristics of dose-response relationships for copper-induced toxicity in relation to excess or deficiency.

Non-linear analysis of the thermo-electro-mechanical behaviour of shear deformable FGM plates with piezoelectric actuators

This paper investigates the non-linear bending behaviour of functionally graded plates that are bonded with piezoelectric actuator layers and subjected to transverse loads and a temperature gradient based on Reddy's higher-order shear deformation plate theory. The von Karman-type geometric non-linearity, piezoelectric and thermal effects are included in mathematical formulations. The temperature change is due to a steady-state heat conduction through the plate thickness. The material properties are assumed to be graded in the thickness direction according to a power-law distribution in terms of the volume fractions of the constituents. The plate is clamped at two opposite edges, while the remaining edges can be free, simply supported or clamped. Differential quadrature approximation in the X-axis is employed to convert the partial differential governing equations and the associated boundary conditions into a set of ordinary differential equations. By choosing the appropriate functions as the displacement and stress functions on each nodal line and then applying the Galerkin procedure, a system of non-linear algebraic equations is obtained, from which the non-linear bending response of the plate is determined through a Picard iteration scheme. Numerical results for zirconia/aluminium rectangular plates are given in dimensionless graphical form. The effects of the applied actuator voltage, the volume fraction exponent, the temperature gradient, as well as the characteristics of the boundary conditions are also studied in detail. Copyright (C) 2004 John Wiley Sons, Ltd.