The CMS experiment at the CERN LHC

The Compact Muon Solenoid (CMS) detector is described. The detector operates at the Large Hadron Collider (LHC) at CERN. It was conceived to study proton-proton (and lead-lead) collisions at a centre-of-mass energy of 14 TeV (5.5 TeV nucleon-nucleon) and at luminosities up to 10(34)cm(-2)s(-1) (10(27)cm(-2)s(-1)). At the core of the CMS detector sits a high-magnetic-field and large-bore superconducting solenoid surrounding an all-silicon pixel and strip tracker, a lead-tungstate scintillating-crystals electromagnetic calorimeter, and a brass-scintillator sampling hadron calorimeter. The iron yoke of the flux-return is instrumented with four stations of muon detectors covering most of the 4 pi solid angle. Forward sampling calorimeters extend the pseudo-rapidity coverage to high values (vertical bar eta vertical bar <= 5) assuring very good hermeticity. The overall dimensions of the CMS detector are a length of 21.6 m, a diameter of 14.6 m and a total weight of 12500 t.

Test of a Modular Fault Current Limiter for 220 V Line Using YBCO Coated Conductor Tapes With Shunt Protection

A modular superconducting fault current limiter (SFCL) consisting of 16 elements was constructed and tested in a 220 V line for a fault current between 1 kA to 7.4 kA. The elements are made up of second generation (2G) YBCO-coated conductor tapes with stainless steel reinforcement. For each element four tapes were electrically connected in parallel with effective length of 0.4 m per element, totaling 16 elements connected in series. The evaluation of SFCL performance was carried out under DC and AC tests. The DC test was performed through pulsed current tests and its recovery characteristics under load current were analysed by changing the shunt resistor value. The AC test performed using a 3 MVA/220 V/60 Hz transformer has shown the current limiting ratio achieved a factor higher than 10 during fault of up to five cycles without conductor degradation. The measurement of the voltage for each element during the AC test showed that in this modular SFCL the quench is homogeneous and the transition occurs similarly in all the elements.

Modular high-current generator for electromagnetic forming with energy recovery

A 10 kJ electromagnetic forming (EMF) modulator with energy recovery based on two resonant power modules, each containing a 4.5 kV/30-kA silicon controlled rectifier, a 1.11-mF capacitor bank and an energy recovery circuit, working in parallel to allow a maximum actuator discharge current amplitude and rate of 50 kA and 2 kA/mu s was successfully developed and tested. It can be plugged in standard single phase 230 V/16 A mains socket and the circuit is able to recover up to 32% of its initial energy, reducing the charging time of conventional EMF systems by up to 68%.

Multilevel high-voltage pulse generation based on a new modular solid-state switch

This paper describes a modular solid-state switching cell derived from the Marx generator concept to be used in topologies for generating multilevel unipolar and bipolar high-voltage (HV) pulses into resistive loads. The switching modular cell comprises two ON/OFF semiconductors, a diode, and a capacitor. This cell can be stacked, being the capacitors charged in series and their voltages balanced in parallel. To balance each capacitor voltage without needing any parameter measurement, a vector decision diode algorithm is used in each cell to drive the two switches. Simulation and experimental results, for generating multilevel unipolar and bipolar HV pulses into resistive loads are presented.

Major: Electronics and Communication Engineering

Today, information technology is strategically important to the goals and aspirations of the business enterprises, government and high-level education institutions – university. Universities are facing new challenges with the emerging global economy characterized by the importance of providing faster communication services and improving the productivity and effectiveness of individuals. New challenges such as provides an information network that supports the demands and diversification of university issues. A new network architecture, which is a set of design principles for build a network, is one of the pillar bases. It is the cornerstone that enables the university’s faculty, researchers, students, administrators, and staff to discover, learn, reach out, and serve society. This thesis focuses on the network architecture definitions and fundamental components. Three most important characteristics of high-quality architecture are that: it’s open network architecture; it’s service-oriented characteristics and is an IP network based on packets. There are four important components in the architecture, which are: Services and Network Management, Network Control, Core Switching and Edge Access. The theoretical contribution of this study is a reference model Architecture of University Campus Network that can be followed or adapted to build a robust yet flexible network that respond next generation requirements. The results found are relevant to provide an important complete reference guide to the process of building campus network which nowadays play a very important role. Respectively, the research gives university networks a structured modular model that is reliable, robust and can easily grow.

Robots and robotic systems for the electronics and telecommunication industry

Tämä diplomityö tutkii elektroniikka- ja telekommunikaatioteollisuutta sekä siihen läheisesti liittyviä robotteja ja robottijärjestelmiä. Tavoitteena on määrittää E&T-teollisuuden prosesseihin soveltuvien robottien testausmenetelmä. Tavoitteena on myös selvittää kahden ABB:n robotin soveltuvuutta E&T-teollisuuden tarpeisiin. Muutamia systemaattisia valmistusjärjestelmien suunnitteluun soveltuvia menetelmiä ja apuvälineitä on myös käsitelty. Alussa työ keskittyy elektroniikka- ja telekommunikaatioteollisuuden nykytilan tutkimiseen sekä siellä vallitsevien ja ennustettujen trendien kartoitukseen. Kohdat “Collaborative manufacturing” ja E&T-teollisuuden valmistusjärjestelmille asettamat vaatimukset käydään yksityiskohtaisesti läpi. Tutkimuksen pääkohteina ovat robotit, erityisesti ABB:n IRB 140 ja IRB 340 sekä robottien testausmenetelmän määrittäminen. Työssä käydään läpi IRB 340:llä suoritetut testit, jotka tehtiin sekä konenäköjärjestelmää apuna käyttäen että ilman. Myös TTKK:lla suoritetut robottitestit on käyty läpi. Robottien testituloksia on analysoitu ja vertailtu muihin robotteihin. Testausmenetelmät perustuvat ISO 9283 standardiin. Viimeinen osa työstä esittelee robottijärjestelmien systemaattiseen suunnitteluun soveltuvia menetelmiä ja apuvälineitä. Esillä ovat mm. Modular function deployment (MFD) ja The system design method (SDM).

Distributed ControlArchitecture of Power Electronics Building-Block-Based Frequency Converters

The increasing power demand and emerging applications drive the design of electrical power converters into modularization. Despite the wide use of modularized power stage structures, the control schemes that are used are often traditional, in other words, centralized. The flexibility and re-usability of these controllers are typically poor. With a dedicated distributed control scheme, the flexibility and re-usability of the system parts, building blocks, can be increased. Only a few distributed control schemes have been introduced for this purpose, but their breakthrough has not yet taken place. A demand for the further development offlexible control schemes for building-block-based applications clearly exists. The control topology, communication, synchronization, and functionality allocationaspects of building-block-based converters are studied in this doctoral thesis. A distributed control scheme that can be easily adapted to building-block-based power converter designs is developed. The example applications are a parallel and series connection of building blocks. The building block that is used in the implementations of both the applications is a commercial off-the-shelf two-level three-phase frequency converter with a custom-designed controller card. The major challenge with the parallel connection of power stages is the synchronization of the building blocks. The effect of synchronization accuracy on the system performance is studied. The functionality allocation and control scheme design are challenging in the seriesconnected multilevel converters, mainly because of the large number of modules. Various multilevel modulation schemes are analyzed with respect to the implementation, and this information is used to develop a flexible control scheme for modular multilevel inverters.

Vidibus: a low-cost, modular bus system for real-time video processing

The advantages of standard bus systems have been appreciated for many years. The ability to connect only those modules required to perform a given task has both technical and commercial advantages over a system with a fixed architecture which cannot be easily expanded or updated. Although such bus standards have proliferated in the microprocessor field, a general purpose low-cost standard for digital video processing has yet to gain acceptance. The paper describes the likely requirements of such a system, and discusses three currently available commercial systems. A new bus specification known as Vidibus, developed to fulfil these requirements, is presented. Results from applications already implemented using this real-time bus system are also given.

Test of a Modular Fault Current Limiter for 220 V Line Using YBCO Coated Conductor Tapes With Shunt Protection

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Desarrollo de un sistema hardware modular que implemente los instrumentos de un laboratorio de electrónica

El poder disponer de la instrumentación y los equipos electrónicos resulta vital en el diseño de circuitos analógicos. Permiten realizar las pruebas necesarias y el estudio para el buen funcionamiento de estos circuitos. Los equipos se pueden diferenciar en instrumentos de excitación, los que proporcionan las señales al circuito, y en instrumentos de medida, los que miden las señales generadas por el circuito. Estos equipos sirven de gran ayuda pero a su vez tienen un precio elevado lo que impide en muchos casos disponer de ellos. Por esta principal desventaja, se hace necesario conseguir un dispositivo de bajo coste que sustituya de alguna manera a los equipos reales. Si el instrumento es de medida, este sistema de bajo coste puede ser implementado mediante un equipo hardware encargado de adquirir los datos y una aplicación ejecutándose en un ordenador donde analizarlos y presentarlos en la pantalla. En el caso de que el instrumento sea de excitación, el único cometido del sistema hardware es el de proporcionar las señales cuya configuración ha enviado el ordenador. En un equipo real, es el propio equipo el que debe realizar todas esas acciones: adquisición, procesamiento y presentación de los datos. Además, la dificultad de realizar modificaciones o ampliaciones de las funcionalidades en un instrumento tradicional con respecto a una aplicación de queda patente. Debido a que un instrumento tradicional es un sistema cerrado y uno cuya configuración o procesamiento de datos es hecho por una aplicación, algunas de las modificaciones serían realizables modificando simplemente el software del programa de control, por lo que el coste de las modificaciones sería menor. En este proyecto se pretende implementar un sistema hardware que tenga las características y realice las funciones del equipamiento real que se pueda encontrar en un laboratorio de electrónica. También el desarrollo de una aplicación encargada del control y el análisis de las señales adquiridas, cuya interfaz gráfica se asemeje a la de los equipos reales para facilitar su uso. ABSTRACT. The instrumentation and electronic equipment are vital for the design of analogue circuits. They enable to perform the necessary testing and study for the proper functioning of these circuits. The devices can be classified into the following categories: excitation instruments, which transmit the signals to the circuit, and measuring instruments, those in charge of measuring the signals produced by the circuit. This equipment is considerably helpful, however, its high price often makes it hardly accessible. For this reason, low price equipment is needed in order to replace real devices. If the instrument is measuring, this low cost system can be implemented by hardware equipment to acquire the data and running on a computer where analyzing and present on the screen application. In case of an excitation the instrument, the only task of the hardware system is to provide signals which sent the computer configuration. In a real instrument, is the instrument itself that must perform all these actions: acquisition, processing and presentation of data. Moreover, the difficulty of making changes or additions to the features in traditional devices with respect to an application running on a computer is evident. This is due to the fact that a traditional instrument is a closed system and its configuration or data processing is made by an application. Therefore, certain changes can be made just by modifying the control program software. Consequently, the cost of these modifications is lower. This project aims to implement a hardware system with the same features and functions of any real device, available in an electronics laboratory. Besides, it aims to develop an application for the monitoring and analysis of acquired signals. This application is provided with a graphic interface resembling those of real devices in order to facilitate its use.

A simulation environment for bio-inspired heterogeneous chained modular robots

This paper presents a new simulation environment aimed at heterogeneous chained modular robots. This simulator allows testing the feasibility of the design, checking how modules are going to perform in the field and verifying hardware, electronics and communication designs before the prototype is built, saving time and resources. The paper shows how the simulator is built and how it can be set up to adapt to new designs. It also gives some examples of its use showing different heterogeneous modular robots running in different environments.

Control point design using modular logic,

Mode of access: Internet.

A design and implementation methodology for high variety electronics assembly systems

Small indigenous manufacturers of electronic equipment are coming under increasingly severe pressure to adopt a strong defensive position against large multinational and Far Eastern companies. A common response to this threat has been for these firms to adopt a 'market driven' business strategy based on quality and customer service, rather than a 'technology led' strategy which uses technical specification and price to compete. To successfully implement this type of strategy there is a need for production systems to be redesigned to suit the new demands of marketing. Increased range and fast response require economy of scope rather t ban economy or scale while the organisation's culture must promote quality and process consciousness. This paper describes the 'Modular Assembly Cascade' concept which addresses these needs by applying the principles of flexible manufacturing (FMS) and just in time (,JlT) to electronics assembly. A methodology for executing the concept is also outlined. This is called DRAMA (Design Houtirw !'or· Adopting Modular Assembly).

Modular system design and control for flexible assembly

Flexible Assembly Systems (FASs) are normally associated with the automatic, or robotic, assembly of products, supported by automated material handling systems. However, manual assembly operations are still prevalent within many industries, where the complexity and variety of products prohibit the development of suitable automated assembly equipment. This article presents a generic model for incorporating flexibility into the design and control of assembly operations concerned with high variety/low volume manufacture, drawing on the principles for Flexible Manufacturing Systems (FMS) and Just-in-Time (JIT) delivery. It is based on work being undertaken in an electronics company where the assembly operations have been overhauled and restructured in response to a need for greater flexibility, shorter cycle times and reduced inventory levels. The principles employed are in themselves not original. However, the way they have been combined and tailored has created a total manufacturing control system which represents a new concept for responding to demands placed on market driven firms operating in an uncertain environment.