Design of a state observer using decay rate LMI constraints for fault detection in mechanical systems

Nowadays, one of the most important concerns for many companies is to maintain the operation of their systems without sudden equipment break down. Because of this, new techniques for fault detection and location in mechanical systems subject to dynamic loads have been developed. This paper studies of the influence of the decay rate in the design of state observers using LMI for fault detection in mechanical systems. This influence is analyzed by the performance index proposed by Huh and Stein for the condition of a state observer. An example is presented to illustrate the methodology discussed.

Monitoramento da Integridade Estrutural de Sistemas Mecânicos via Observador de Estado Modal

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

A Luenberger state observer for stator resistance estimation in sensorless induction motor drives

The primary objective of this paper is to elimination of the problem of sensitivity to parameter variation of induction motor drive. The proposed sensorless strategy is based on an algorithm permitting a better simultaneous estimation of the rotor speed and the stator resistance including an adaptive mechanism based on the lyaponov theory. To study the reliability and the robustness of the sensorless technique to abnormal operations, some simulation tests have been performed under several cases. The proposed sensorless vector control scheme showed a good performance behavior in the transient and steady states, with an excellent disturbance rejection of the load torque. © 2013 Praise Worthy Prize S.r.l. - All rights reserved.

Variable structure controller and observer applied to induction machine

This work will propose the control of an induction machine in field coordinates with imposed stator current based on theory of variable structure control and sliding mode. We describe the model of an induction machine in field coordinates with imposed stator current and we show the design of variable structure control and sliding mode to get a desirable dynamic performance of that plant. To estimate the inaccessible states we will use a state observer (estimator) based on field coordinates induction machine. We will present the results of simulations in any operation condition (start, speed reversal and load) and with parameters variation of the machine compared to a PI control scheme.

Aktiivisten magneettilaakereiden tilasäädön mallinnus ja simulointi

Aktiivisten magneettilaakereiden avulla on mahdollista kannatella ferromagneettisia kappaleita, kuten sähkökoneiden roottoreita, ilman fyysistä kontaktia. Magneettilaakerit tarjoavat monia etuja, kuten esimerkiksi kitkattomuuden, verrattuina perinteisiin mekaanisiin laakereihin. Nämä edut vielä korostuvat suurnopeuskäytöissä, jotka ovat magneettilaakereiden pääasiallisia käyttökohteita. Tässä työssä esitellään magneettilaakereihin liittyvät erusteoriat ja niiden sovellustavat. Tämän jälkeen tarkastellaanmagneettilaakereiden kanssa käytettäviä säätöratkaisuja ja esitetään niille soveltuvat viritysmenetelmät. Teorioiden pohjalta rakennetaan täydellinen magneettilaakerijärjestelmän simulointimalli säätöratkaisuineen ja suoritetaan järjestelmän toimintaa kuvaavia simulointeja. Simuloinneissa saadut tulokset pyritään vielä varmentamaan suorittamalla mittauksia koelaitteistolla ja vertaamalla saatuja tuloksia keskenään.

Contact Sensing: A Sequential Decision Approach to Sensing Manipulation Contact

This paper describes a new statistical, model-based approach to building a contact state observer. The observer uses measurements of the contact force and position, and prior information about the task encoded in a graph, to determine the current location of the robot in the task configuration space. Each node represents what the measurements will look like in a small region of configuration space by storing a predictive, statistical, measurement model. This approach assumes that the measurements are statistically block independent conditioned on knowledge of the model, which is a fairly good model of the actual process. Arcs in the graph represent possible transitions between models. Beam Viterbi search is used to match measurement history against possible paths through the model graph in order to estimate the most likely path for the robot. The resulting approach provides a new decision process that can be use as an observer for event driven manipulation programming. The decision procedure is significantly more robust than simple threshold decisions because the measurement history is used to make decisions. The approach can be used to enhance the capabilities of autonomous assembly machines and in quality control applications.

Sistema híbrido para detecção e diagnóstico de falhas em sistemas dinâmicos

The industries are getting more and more rigorous, when security is in question, no matter is to avoid financial damages due to accidents and low productivity, or when it s related to the environment protection. It was thinking about great world accidents around the world involving aircrafts and industrial process (nuclear, petrochemical and so on) that we decided to invest in systems that could detect fault and diagnosis (FDD) them. The FDD systems can avoid eventual fault helping man on the maintenance and exchange of defective equipments. Nowadays, the issues that involve detection, isolation, diagnose and the controlling of tolerance fault are gathering strength in the academic and industrial environment. It is based on this fact, in this work, we discuss the importance of techniques that can assist in the development of systems for Fault Detection and Diagnosis (FDD) and propose a hybrid method for FDD in dynamic systems. We present a brief history to contextualize the techniques used in working environments. The detection of fault in the proposed system is based on state observers in conjunction with other statistical techniques. The principal idea is to use the observer himself, in addition to serving as an analytical redundancy, in allowing the creation of a residue. This residue is used in FDD. A signature database assists in the identification of system faults, which based on the signatures derived from trend analysis of the residue signal and its difference, performs the classification of the faults based purely on a decision tree. This FDD system is tested and validated in two plants: a simulated plant with coupled tanks and didactic plant with industrial instrumentation. All collected results of those tests will be discussed

Analise de desempenho de observadores de estado robustos na localizacao de falhas

The state observers can reconstruct and monitor unmeasurable states. A new concept of fault detection and isolation using state observers is presented. The method selects the parameters from components that may fail during the process and constructs optimized robust observers. To isolate component failures via robust observation, a bank of detection observers is organized, in which each observer is only sensitive to one specified component failure while robust to all other component failures. This paper analyzes the performance of transient and steady-state behavior of the state observer.

Utilização de modelos de falhas e observadores de estado em estruturas reticuladas

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Controle de movimentos de pacientes paraplégicos utilizando modelos fuzzy T-S

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Métodos de identificação e redução de modelos para atenuação de vibrações em estruturas inteligentes

Pós-graduação em Engenharia Mecânica - FEIS

Método híbrido para detecção e diagnóstico de falhas baseado em resíduos

The detection and diagnosis of faults, ie., find out how , where and why failures occur is an important area of study since man came to be replaced by machines. However, no technique studied to date can solve definitively the problem. Differences in dynamic systems, whether linear, nonlinear, variant or invariant in time, with physical or analytical redundancy, hamper research in order to obtain a unique solution . In this paper, a technique for fault detection and diagnosis (FDD) will be presented in dynamic systems using state observers in conjunction with other tools in order to create a hybrid FDD. A modified state observer is used to create a residue that allows also the detection and diagnosis of faults. A bank of faults signatures will be created using statistical tools and finally an approach using mean squared error ( MSE ) will assist in the study of the behavior of fault diagnosis even in the presence of noise . This methodology is then applied to an educational plant with coupled tanks and other with industrial instrumentation to validate the system.

Observer-based state-feedback versus H-infinity output feedback control solved by LMI approach for applications in smart structures

This paper aims with the use of linear matrix inequalities approach (LMIs) for application in active vibration control problems in smart strutures. A robust controller for active damping in a panel was designed with piezoelectrical actuators in optimal locations for illustration of the main proposal. It was considered, in the simulations of the closed-loop, a model identified by eigensystem realization algorithm (ERA) and reduced by modal decomposition. We tested two differents techniques to solve the problem. The first one uses LMI approach by state-feedback based in an observer design, considering several simultaneous constraints as: a decay rate, limited input on the actuators, bounded output peak (output energy) and robustness to parametic uncertainties. The results demonstrated the vibration attenuation in the structure by controlling only the first modes and the increased damping in the bandwidth of interest. However, it is possible to occur spillover effects, because the design has not been done considering the dynamic uncertainties related with high frequencies modes. In this sense, the second technique uses the classical H. output feedback control, also solved by LMI approach, considering robustness to residual dynamic to overcome the problem found in the first test. The results are compared and discussed. The responses shown the robust performance of the system and the good reduction of the vibration level, without increase mass.

Self-ratings and observer-ratings of social skill: a manipulation of state social anxiety in anxious and non-anxious children

The role of state and trait anxiety on observer ratings of social skill and negatively biased self-perception of social skill was examined. Participants were aged between 7 and 13 years (mean=9.65; sd=1.77; N=102), 47 had a current anxiety diagnosis and 55 were non-anxious controls. Participants were randomly allocated to a high or low anxiety condition and asked to complete social tasks. Task instructions were adjusted across conditions to manipulate participants’ state anxiety. Observers rated anxious participants as having poorer social skills than non-anxious controls but there was no evidence that anxious participants exhibited a negative self-perception bias, relative to controls. However, as participants’ ratings of state anxiety increased, their perception of their performance became more negatively biased. The results suggest that anxious children may exhibit real impairments in social skill and that high levels of state anxiety can lead to biased judgements of social skills in anxious and non-anxious children.

Spectral behavior of some modal soil profiles from São Paulo State, Brazil

Remote sensing has a high potential for environmental evaluation. However, a necessity exists for a better understanding of the relations between the soil attributes and spectral data. The objective of this work was to analyze the spectral behavior of some soil profiles from the region of Piracicaba, São Paulo State, using a laboratory spectroradiometer (400 to 2500 nm). The relations between the reflected electromagnetic energy and the soil physical, chemical and mineralogical attributes were analyzed, verifying the spectral variations of soil samples in depth along the profiles with their classification and discrimination. Sandy soil reflected more, presenting a spectral curve with an ascendant form, opposite to clayey soils. The 1900 nm band discriminated soil with 2:1 mineralogy from the 1:1 and oxidic soils. It was possible to detect the presence of kaolinite, gibbsite, hematite and goethite in the soils through the descriptive aspects of curves, absorption features and reflectance intensity. A relation exists between the weathering stage and spectral data. The evaluation of the superficial and subsuperficial horizon samples allowed characterizing and discriminating the analytical variability of the profile, helping to soil distinguishing and classification.