The incorporation of construction and demolition wastes as recycled mixed aggregates in non-structural concrete precast pieces

Concern for the environment has lately heightened awareness about the need for recycling in the construction industry. However, some standards, such as the Spanish standard, only accept the recycling of aggregates derived from concrete, which limits the extensive use of construction and demolition waste, which are produced in much bigger volumes. The aim of this work was to explore the possibility of using recycled mixed aggregates (RMA) in the preparation of precast non-structural concretes. To that end different percentages of natural aggregate were replaced by RMA in non-structural elements (25, 50, 75 and 100%). Contents of cement, water, and the dosages commonly used by companies were unchanged by the introduction of RMA. The characterization of the prepared elements has been done using the specific tests for each type of non-structural element (terrazzo for indoor use, hollow tiles, kerbstones and paving blocks): compression and flexural strength, water absorption, dimensional tolerances, abrasion and slipping resistance. The paving blocks, kerbstones, and hollow tiles prepared were tested for 360 days. The stability of the tested properties confirmed the possibility of using these wastes on an industrial scale satisfying the standard requirements. However, the surface of terrazzo with RMA is not as good as that prepared with natural aggregate.

Limiting properties in the characterisation of mixed recycled aggregates for use in the manufacture of concrete

El objetivo principal de este trabajo de investigación es estudiar las propiedades del árido reciclado mixto para la fabricación de hormigón reciclado en aplicaciones no estructurales. Se ha realizado la caracterización completa de 35 muestras de áridos reciclados mixtos gruesos de distinta calidad, procedentes de 13 plantas de tratamiento diferentes de la geografía española. Se han estudiado las correlaciones que existen entre las diferentes propiedades, en particular, con la absorción de agua, el contenido de sulfatos y la composición. Se propone una clasificación de los áridos reciclados y se limita de forma indicativa el contenido de yeso para que una muestra de árido reciclado mixto cumpla con la limitación del 0,8% de los sulfatos solubles en ácido de la Instrucción EHE-08. Recycling of construction and demolition waste (CDW) has become a widespread concern in Spain for the last years, as a way to preserve natural resources and achieve a better control of waste disposal sites.Specific applications which make use of mixed recycled aggregates are of great importance, as this types of aggregates constitute the majority of the total production. Structural and non-structural concrete is one of the possible applications, being this the main goal of our study. This paper presents a study on the physical and chemical characteristics of mixed recycled aggregates which have been obtained from different CDW treatment plants of Spain. Correlations between the different properties were investigated in order to find criterions of acceptance for recycled aggregates to be used in concrete. The comparison between the properties offers the possibility of pre-selecting a great quantity of mixed recycled aggregates, these being suitable for either structural and non-structural concrete. The determination of water absorption and the gypsum content are good indicators in order to evaluate the quality of the mixed recycled aggregates for its application in the production of concrete.

Il calcestruzzo con aggregati di riciclo: sviluppi ed applicazioni nel panorama nazionale ed internazionale.

Il calcestruzzo è uno dei materiali più utilizzati nell’edilizia, ma il meno sostenibile. Per la sua produzione vengono sfruttate elevate quantità di risorse naturali non rinnovabili con un impatto ambientale non trascurabile, sia per le sostanze emesse in atmosfera, sia per le macerie derivate post utilizzo. L’ingresso nel XXI secolo ha segnato definitivamente l’affermazione del concetto di sviluppo sostenibile nei riguardi di tutti i processi produttivi dei beni, che devono essere necessariamente strutturati secondo una logica di risparmio energetico e di controllo della produzione di scorie e rifiuti, prevedendone un loro riutilizzo in altri settori, o un loro smaltimento senza provocare danni all’ambiente. Anche l’industria del cemento e del calcestruzzo è chiamata a svolgere il proprio ruolo per contribuire ad un miglior bilancio ecologico globale, indirizzando la ricerca verso possibilità d’impiego di materiali “innovativi”, che siano in grado di sostituire parzialmente o totalmente l’uso di materie prime non rinnovabili, tenendo conto dell’enorme richiesta futura di infrastrutture, soprattutto nei paesi in via di sviluppo. Negli ultimi anni si sta sempre più affermando il potenziale del riciclo dei materiali ottenuti dalla demolizione di edifici (C&DW – Construction and Demolition Waste), questo dovuto anche a politiche di gestione dei rifiuti che incentivano il risparmio, il riutilizzo, il riciclo e la valorizzazione dei beni. I calcestruzzi con aggregati di riciclo sono generalmente suddivisi in due macrogruppi: quelli ottenuti da aggregati di riciclo di solo calcestruzzo (RCA – Recycled Coarse Aggregate) e quelli da aggregati da demolizione totale (MRA – Mixed Recycled Aggregate) che però contengono molte impurità. Come anche uno può subito pensare gli aggregati riciclati hanno delle proprietà diverse da quelli naturali, questi contengono oltre l’aggregato naturale anche il legante coeso, polveri di laterizio, vetro, ceramica, plastica eccet., i quali offrono una miscela ricca di cloruri, solfati, silice amorfa ed altri componenti dannosi per la nuova miscela di calcestruzzo. In presenza di questi prodotti, gli aggregati non solo non soddisfano i requisiti chimici, ma influiscono negativamente anche sulle proprietà fisico-meccaniche del calcestruzzo. Per questo vedremmo in questa tesi tramite un accurata analisi degli aggregati, e del loro “contributo” per il corretto comportamento del calcestruzzo, leggendo criticamente come le normative regolano i requisiti che gli aggregati debbono soddisfare, vedendo le varie possibilità di riutilizzo dei materiali di riciclo da demolizione. La tesi mira all'incentivo dei materiali da riciclo, come scelta sostenibile per il futuro dell'edilizia. E' stato calcolato che la produzione totale di macerie da demolizione nel mondo, non supera il 20% in massa degli aggregati che vengono utilizzati per la produzione del calcestruzzo nei paesi sviluppati. Dai vari studi è stato valutato in media che col solo 20% di riciclato sostituito, le caratteristiche del calcestruzzo indurito cambiano di poco dal normale miscelato con aggregati naturali; ovviamente se gli aggregati da riciclo sono stati selezionati e sottoposti ai vari test delle norme europee standardizzate. Quindi uno può subito pensare in linea teorica, tralasciando i costi di gestione, trasporto eccet. , che basta utilizzare per ogni metro cubo di calcestruzzo 20% di riciclato, per rispondere allo smaltimento dei rifiuti da C&D; abbassando cosi i costi degli inerti naturali, sempre parlando di economie di scala. Questo è in linea teorica, ma riflette un dato rilevante. Nel presente lavoro si partirà da una veloce lettura sul comportamento del calcestruzzo, su i suoi principali costituenti, concentrandoci sugli aggregati, analizzandone le sue proprietà fisico-meccaniche, quali la granulometria, la resistenza meccanica e la rigidezza, valutando l’importanza dei legami coesivi tra aggregato alla pasta cementizia. Verranno inoltre analizzate le azioni deleterie che possono instaurarsi tra aggregato di riciclo e pasta cementizia. Dopo aver visto le varie politiche sulla gestione dei rifiuti, la legislazione passata e presente sull’uso dei materiali riciclati, si analizzeranno vari studi sulle proprietà fisico-meccaniche dei calcestruzzi con aggregati di riciclo seguiti da università e poli di ricerca internazionali. Se gli aggregati di riciclo sono selezionati con metodo, in presenza di piani di gestione regionale e/o nazionale, è possibile soddisfare le prestazioni richieste del calcestruzzo, nel rispetto delle politiche di sostenibilità economico-ambientali. Può essere il calcestruzzo riciclato una scelta non solo sostenibile, ma anche economica per il settore edile? Si può avere un calcestruzzo riciclato ad alte prestazioni? Quali sono le politiche da mettere in atto per un mercato di produzione sostenibile del riciclato? Questo e molto altro verrà approfondito nelle pagine seguenti di questa tesi.

Estudio de hormigones reciclados no estructurales fabricados con árido reciclado mixto : propiedades mecánicas y expansión debida al contenido de sulfatos

El objetivo principal de este trabajo de investigación es estudiar las posibilidades de utilización del árido reciclado mixto para un hormigón reciclado en aplicaciones no estructurales, justificando mediante la experimentación la validez para esta aplicación, tanto del árido reciclado como del hormigón reciclado. Esta tesis se centró en los aspectos más restrictivos y limitativos en la utilización de los áridos mixtos en hormigón reciclado, basándose tanto en la normativa internacional existente como en los resultados obtenidos en los estudios bibliográficos consultados. La primera tarea realizada fue la caracterización completa de las propiedades del árido reciclado mixto, recogiendo especialmente los siguientes aspectos: granulometría, contenido de finos, absorción y densidades, composición del árido reciclado, índice de lajas, coeficiente de Los Ángeles, partículas ligeras y contenido de sulfatos. De este estudio de los áridos reciclados, se han destacado relaciones entre las propiedades. Las diferentes correlaciones permiten proponer criterios de calidad de un árido reciclado mixto para un hormigón reciclado. Se ha elegido un árido reciclado mixto entre los estudiados, de características límite admisibles, para obtener resultados conservadores sobre el hormigón reciclado fabricado con él. En una segunda etapa, se ha realizado un estudio de dosificación completo del hormigón reciclado, evaluando la consistencia del hormigón en estado fresco y la resistencia a compresión del hormigón en estado endurecido y se ha comparado con las mismas propiedades de un hormigón convencional. Se ha analizado la capacidad de absorción del árido conseguida con los métodos de presaturación empleados y en función de su estado de humedad, para poder evaluar las relaciones agua/cemento totales y efectivas del hormigón. Se ha estudiado el efecto de estos dos parámetros tanto en la consistencia como en la resistencia del hormigón reciclado. Finalmente, se ha estudiado el hormigón fabricado con un 50% y 100% de una partida de árido reciclado mixto de calidad admisible y se han ensayado las siguientes propiedades: consistencia, resistencia a compresión, resistencia a tracción indirecta, módulo de elasticidad dinámico, cambios de longitud, porosidad abierta y microscopía. Para analizar el efecto de los sulfatos, se han añadido artificialmente cantidades de yeso controladas en el hormigón reciclado. Se fabricaron hormigones con dos tipos de cemento, un cemento CEM I 42,5 R con elevado contenido de C3A, que debería dar lugar a expansiones mayores y un cemento con adiciones puzolánicas CEM II A-P 42,5 R, que atenuaría el comportamiento expansivo en el hormigón. Los resultados finales indican que la utilización del árido reciclado mixto en proporciones de hasta un 50%, permiten cubrir la gama de resistencias más exigentes dentro del hormigón no estructural. El contenido de sulfatos puede variar desde un 0,8% hasta un 1,9%, según el tipo de cemento y la proporción de sustitución del árido natural por árido reciclado mixto. Tanto en el caso del árido reciclado como en el hormigón, se ha realizado un estudio comparativo entre el conjunto de datos recopilados en la bibliografía y los obtenidos en este estudio experimental. En varias propiedades del hormigón reciclado, se han comparado los resultados con las fórmulas de la Instrucción EHE-08, para establecer unos coeficientes de corrección a aplicar a un hormigón reciclado con fines no estructurales. The main objective of this investigation work is to study the possibilities of using recycled mixed aggregate for a recycled concrete in non structural applications, justifying by means of experimentation both the validity of the recycled aggregate and recycled concrete. This thesis focused on the most restrictive and limiting aspects in the mixed aggregate use in recycled concrete, on the basis of the international standards as well on the results obtained in the bibliographic studies consulted. The first task achieved was the complete charcaterization of the mixed recycled aggregate properties, specially the following aspects: grain size analysis, fines content, absorption and densities, recycled aggregate composition, flakiness index, Los Angeles coefficient, lightweight particles and sulphate content. From this study, correlations between the properties were highlighted. The different correlations make possible to propose quality criterions for recycled mixed aggregate in concrete. Among the recycled aggregates studied, one of acceptable characteristics but near the limits established, was chosen to obtain conservative results in the recycled concrete made with it. In a second step, a complete recycled concrete mix design was made, to evaluate concrete consistency in the fresh state and concrete compressive strength in the hardened state and its properties were compared to those of a control concrete. The aggregate absorption capacity was analized with the presaturation methods achieved and in function of its state of humidity, to evaluate the total and effective water/cement ratios. The effect of these two parameters, both in consistency and compressive strength of recycled concrete, was studied. Finally, the concrete made with 50% and 100% of the elected recycled mixed aggregate was studied and the following concrete properties were tested: consistency, compressive strength, tensile strength, dynamic modulus of elasticity, length changes, water absorption under vacuum and microscopy. To analize the effect of sulphate content, some controlled quantities of gypsum were artificially added to the recycled concrete. Concretes with two types of cement were made, a cement CEM I 42,5 R with a high content of C3A, that would lead to major expansions and a cement with puzzolanic additions CEM II A-P 42,5 R that would lower the expansive behaviour of concrete. The final results indicate that the use of mixed recycled aggregate in proportions up to 50% make possible to cover the overall demanding strengths within the non structural concrete. Sulphates content can range between 0,8% and 1,9%, in function of the type of cement and the proportion of natural aggregate replacement by mixed recycled one. Both in the case of recycled aggregate and concrete, a comparative study was made between the data coming from the bibliography and those obtained in the experimental study. In several recycled concrete properties, the results were compared to the formulas of Spanish Instruction of Structural Concrete (Instruction EHE-08), to establish some correction coefficients to apply for a non structural recycled concrete.

On the classification of mixed construction and demolition waste aggregate by porosity and its impact on the mechanical performance of concrete

The properties of recycled aggregate produced from mixed (masonry and concrete) construction and demolition (C&D) waste are highly variable, and this restricts the use of such aggregate in structural concrete production. The development of classification techniques capable of reducing this variability is instrumental for quality control purposes and the production of high quality C&D aggregate. This paper investigates how the classification of C&D mixed coarse aggregate according to porosity influences the mechanical performance of concrete. Concretes using a variety of C&D aggregate porosity classes and different water/cement ratios were produced and the mechanical properties measured. For concretes produced with constant volume fractions of water, cement, natural sand and coarse aggregate from recycled mixed C&D waste, the compressive strength and Young modulus are direct exponential functions of the aggregate porosity. Sink and float technique is a simple laboratory density separation tool that facilitates the separation of cement particles with lower porosity, a difficult task when done only by visual sorting. For this experiment, separation using a 2.2 kg/dmA(3) suspension produced recycled aggregate (porosity less than 17%) which yielded good performance in concrete production. Industrial gravity separators may lead to the production of high quality recycled aggregate from mixed C&D waste for structural concrete applications.

The influence of curing conditions on the mechanical performance of concrete made with recycled concrete waste

Research on the use of Construction and Demolition Waste (CDW) as recycled aggregate (in particular crushed concrete) for the production of new concrete has by now established the feasibility of this environmentally-friendly use of otherwise harmful waste. However, contrary to conventional concrete (CC), no large applications of concrete made with recycled concrete have been made and there is still a lack of knowledge in some areas of production and performance of recycled aggregate concrete (RAC). One issue concerns curing conditions: these greatly affect the performance of concrete made on site and some potential users of RAC wonder how RAC is affected by far-from-ideal curing conditions. This paper shows the main results of experiments to determine the influence of different curing conditions on the mechanical performance of concrete made with coarse recycled aggregate from crushed concrete. The properties analyzed include compressive strength, splitting tensile strength, modulus of elasticity, and abrasion resistance. The general conclusion in terms of mechanical performance is that RAC is affected by curing conditions roughly in the same way as CC. (C) 2011 Elsevier Ltd. All rights reserved.

The effect of superplasticizers on the mechanical performance of concrete made with fine recycled concrete aggregates

It is considered that using crushed recycled concrete as aggregate for concrete production is a viable alternative to dumping and would help to conserve abiotic resources. This use has fundamentally been based on the coarse fraction because the fine fraction is likely to degrade the performance of the resulting concrete. This paper presents results from a research work undertaken at Institut Superior Tecnico (IST), Lisbon, Portugal, in which the effects of incorporating two types of superplasticizer on the mechanical performance of concrete containing fine recycled aggregate were evaluated. The purpose was to see if the addition of superplasticizer would offset the detrimental effects associated with the use of fine recycled concrete aggregate. The experimental programme is described and the results of tests for splitting tensile strength, modulus of elasticity and abrasion resistance are presented. The relative performance of concrete made with recycled aggregate was found to decrease. However, the same concrete with admixtures in general exhibited a better mechanical performance than the reference mixes without admixtures or with a less active superplasticizer. Therefore, it is argued that the mechanical performance of concrete made with fine recycled concrete aggregates can be as good as that of conventional concrete, if superplasticizers are used to reduce the water-cement ratio of the former concrete.

Rheological behaviour of concrete made with fine recycled concrete aggregates - Influence of the superplasticizer

This paper evaluates the influence of two superplasticizers (SP) on the rheological behaviour of concrete made with fine recycled concrete aggregates (FRCA). Three families of concrete were tested: family CO made without SP, family Cl made with a regular superplasticizer and family C2 made with a high-performance superplasticizer. Five replacement ratios of natural sand by FRCA were tested: 0%, 10%, 30%, 50% and 100%. The coarse aggregates were natural gravels. Three criteria were established to design the concrete mixes' composition: keep the same particle size distribution curves, adjust the water/cement ratio to obtain a similar slump and no pre-saturation of the FRCA. All mixes had the same cement and SP content. The results show that the incorporation of FRCA significantly increased the shrinkage and creep deformation. The FRCA's effect was influenced by the curing age. The reference concrete made with natural sand stabilizes the creep deformation faster than the mixes made with FRCA. The incorporation of superplasticizer increased the shrinkage at early ages and decreased the shrinkage at 91 days of age. The regular superplasticizer did not improve the creep deformation while the high-performance superplasticizer highly improved this property. The incorporation of FRCA jeopardized the SP's effectiveness. This study demonstrated that to use FRCA and superplasticizer for concrete production it is necessary to take into account the different rheological behaviour of these mixes. (C) 2015 Elsevier Ltd. All rights reserved.

Performance estimation for concretes made with recycled aggregates of construction and demolition waste of some Brazilian cities

The aim of this paper is to verify the influence of composition variability of recycled aggregates (RA) of construction and demolition wastes (CDW) on the performance of concretes. Performance was evaluated building mathematical models for compressive strength, modulus of elasticity and drying shrinkage. To obtain such models, an experimental program comprising 50 concrete mixtures was carried out. Specimens were casted, tested and results for compressive strength, modulus of elasticity and drying shrinkage were statistically analyzed. Models inputs are CDW composition observed at seven Brazilian cities. Results confirm that using RA from CDW for concrete building is quite feasible, independently of its composition, once compressive strength and modulus of elasticity still reached considerable values. We concluded the variability presented by recycled aggregates of CDW does not compromise their use for concrete building. However, this information must be used with caution, and experimental tests should always be performed to certify concrete properties.

Development of sustainable, innovative and energy-efficient concrete, based on the integration of all-waste materials: SUS-CON panels for building applications

The building sector requires the worldwide production of 4 billion tonnes of cement annually, consuming more than 40% of global energy and accounting for about 8% of the total CO2 emissions. The SUS-CON project aimed at integrating waste materials in the production cycle of concrete, for both ready-mixed and pre-cast applications, resulting in an innovative light-weight, ecocompatible and cost-effective construction material, made by all-waste materials and characterized by enhanced thermal insulation performance and low embodied energy and CO2. Alkali activated “cementless” binders, which have recently emerged as eco-friendly construction materials, were used in conjunction with lightweight recycled aggregates to produce sustainable concrete for a range of applications. This paper presents some results from the development of a concrete made with a geopolymeric binder (alkali activated fly ash) and aggregate from recycled mixed plastic. Mix optimisation was achieved through an extensive investigation on production parameters for binder and aggregate. The mix recipe was developed for achieving the required fresh and hardened properties. The optimised mix gave compressive strength of about 7 MPa, flexural strength of about 1.3 MPa and a thermal conductivity of 0.34 W/mK. Fresh and hardened properties were deemed suitable for the industrial production of precast products. Precast panels were designed and produced for the construction of demonstration buildings. Mock-ups of about 2.5 x 2.5 x 2.5 m were built at a demo park in Spain both with SUS-CON and Portland cement concrete, monitoring internal and external temperatures. Field results indicate that the SUS-CON mock-ups have better insulation. During the warmest period of the day, the measured temperature in the SUS-CON mock-ups was lower.

Delta-9-tetrahydrocannabinol accumulation, metabolism and cell-type-specific adverse effects in aggregating brain cell cultures.

Despite the widespread use of Cannabis as recreational drug or as medicine, little is known about its toxicity. The accumulation, metabolism and toxicity of THC were analyzed 10 days after a single treatment, and after repeated exposures during 10 days. Mixed-cell aggregate cultures of fetal rat telencephalon were used as in vitro model, as well as aggregates enriched either in neurons or in glial cells. It was found that THC accumulated preferentially in neurons, and that glia-neuron interactions decreased THC accumulation. The quantification of 11-OH-THC and of THC-COOH showed that brain aggregates were capable of THC metabolism. No cell-type difference was found for the metabolite 11-OH-THC, whereas the THC-COOH content was higher in mixed-cell cultures. No cell death was found at THC concentrations of 2 microM in single treatment and of 1 microM and 2 microM in repeated treatments. Neurons, and particularly GABAergic neurons, were most sensitive to THC. Only the GABAergic marker was affected after the single treatment, whereas the GABAergic, cholinergic and astrocytic markers were decreased after the repeated treatments. JWH 015, a CB2 receptor agonist, showed effects similar to THC, whereas ACEA, a CB1 receptor agonist, had no effect. The expression of the cytokine IL-6 was upregulated 48 h after the single treatment with 5 microM of THC or JWH 015, whereas the expression of TNF-alpha remained unchanged. These results suggest that the adverse effects of THC were related either to THC accumulation or to cannabinoid receptor activation and associated with IL-6 upregulation.

Involvement of glial cells in the neurotoxicity of parathion and chlorpyrifos.

An in vitro model, the aggregating brain cell culture of fetal rat telencephalon, has been used to investigate the influence of glial cells on the neurotoxicity of two organophosphorus pesticides (OPs), chlorpyrifos and parathion. Mixed-cell aggregate cultures were treated continuously for 10 days between DIV 5 and 15. Parathion induced astrogliosis at concentration at which MAP-2 immunostaining, found here to be more sensitive than neuron-specific enzyme activities, was not affected. In contrast, chlorpyrifos induced a comparatively weak gliotic reaction, and only at concentrations at which neurons were already affected. After similar treatments, increased neurotoxicity of parathion and chlorpyrifos was found in aggregate cultures deprived of glial cells. These results suggest that glial cells provide neuroprotection against OPs toxicity. To address the question of the difference in toxicity between parathion and chlorpyrifos, the toxic effects of their leaving groups, p-nitrophenol and trichloropyridinol, were studied in mixed-cell aggregates. General cytotoxicity was more pronounced for trichloropyridinol and both compounds had similar toxic effects on neuron-specific enzyme activities. In contrast, trichloropyridinol induced a much stronger decrease in glutamine synthetase activity, the enzymatic marker of astrocytes. Trichloropyridinol may exert a toxic effect on astrocytes, compromising their neuroprotective function, thus exacerbating the neurotoxicity of chlorpyrifos. This is in line with the suggestion that glial cells may contribute to OPs neurotoxicity, and with the view that OPs may exert their neurotoxic effects through different mechanisms.

Desempenho de argamassas produzidas com agregados reciclados oriundos do resíduo de construção e demolição da Grande Natal-RN

The construction industry is responsible for generating a lot of waste because of their activities. Consequently, it is noticeable the occurrence of environmental problems in terms of its disposal in inappropriate places. Faced with this problem, some studies have been conducted with the aim of developing technologies and alternatives for recycling construction and demolition waste (CDW), motivated by the scarcity of natural resources and reduction of environmental problems generated. The research aims to characterize the recycled aggregates derived from construction and demolition waste (CDW) produced in the Greater Natal-RN and analyze the performance of mortar coating produced with recycled aggregates. The study includes the chemical , physical and microstructural characterization of recycled aggregates , as well as conducting microscopic analysis and laboratory tests in the fresh state (consistency index , water retention , bulk density and content of entrained air ) and in the hardened state ( compressive strength , tensile strength in bending , water absorption by immersion and capillary , mass density and void ratio ) for mortars produced from different levels of substitution of aggregates ( 0, 20 %, 40 %, 60 %, 80 % and 100 %). The results were satisfactory, providing mortars produced with recycled aggregates, smaller mass density and dynamic modulus values as well as an increase in the rates of absorption and porosity. The tensile strength in bending and compression for TP1 (1:2:8) trait were lower for mortars produced with recycled aggregates and the best result was 20% for replacement. For the TP2 (1:8) mapping, there was an increase in resistance to traction and compression and the best result was for 100% replacement of natural aggregates by recycled. The experiments led to the conclusion that the technical and economic point of view that the mortars produced with recycled aggregates can be used in construction, only if there is an effective control in production processes of recycled aggregate and at the dosage of mortars