Tensoes Residuais na Soldagem, Aspectos Basicos

The purpose of this paper is to analyze the basic aspects of the residual stresses in welding. Concepts about macro and micro residual stresses in metals are considered in welding. In a simple welding model is shown how shrinkage macro stress results and how this can contribute to understand the distribution of residual stresses in common type of welded joint. Further, comments are made concerning the effects of additional mechanical and metallurgical phenomena, distortion in weldments and dimensional discrepancies.

Importance of considering a material micro-failure criterion in the numerical modelling of the shot peening process applied to parabolic leaf springs

Shot peening is a cold-working mechanical process in which a shot stream is propelled against a component surface. Its purpose is to introduce compressive residual stresses on component surfaces for increasing the fatigue resistance. This process is widely applied in springs due to the cyclical loads requirements. This paper presents a numerical modelling of shot peening process using the finite element method. The results are compared with experimental measurements of the residual stresses, obtained by the X-rays diffraction technique, in leaf springs submitted to this process. Furthermore, the results are compared with empirical and numerical correlations developed by other authors.

Residual stresses in TiN, DLC and MoS(2) coated surfaces with regard to their tribological fracture behaviour

Thin hard coatings on components and tools are used increasingly due to the rapid development in deposition techniques, tribological performance and application skills. The residual stresses in a coated surface are crucial for its tribological performance. Compressive residual stresses in PVD deposited TiN and DLC coatings were measured to be in the range of 0.03-4 GPa on steel substrate and 0.1-1.3 GPa on silicon. MoS(2) coatings had tensional stresses in the range of 0.8-1.3 on steel and 0.16 GPa compressive stresses on silicon. The fracture pattern of coatings deposited on steel substrate were analysed both in bend testing and scratch testing. A micro-scale finite element method (FEM) modelling and stress simulation of a 2 mu m TiN-coated steel surface was carried out and showed a reduction of the generated tensile buckling stresses in front of the sliding tip when compressive residual stresses of 1 GPa were included in the model. However, this reduction is not similarly observed in the scratch groove behind the tip, possibly due to sliding contact-induced stress relaxation. Scratch and bending tests allowed calculation of the fracture toughness of the three coated surfaces, based on both empirical crack pattern observations and FEM stress calculation, which resulted in highest values for TiN coating followed by MoS(2) and DLC coatings, being K(C) = 4-11, about 2, and 1-2 MPa M(1/2), respectively. Higher compressive residual stresses in the coating and higher elastic modulus of the coating correlated to increased fracture toughness of the coated surface. (C) 2009 Elsevier B.V. All rights reserved.

Effect of rolling on the residual stresses and magnetic properties of a 0.5% Si electrical steel

Cold-rolled (0-19% of reduction) 0.5% Si electrical steel sheets were studied in detail, including macro and micro residual stress measurements, crystallographic texture, dc-hysteresis curves and iron losses. Even for the smallest deformation, losses increase significantly, with large increase of the hysteresis losses, whereas the anomalous losses reduce slightly. The residual microstresses are similar to 150-350 MPa, whereas residual macrostresses are compressive, similar to 50 MPa. The large increase of the hysteresis losses is attributed to the residual microstresses. The dislocation density estimated by X-ray diffraction is in reasonable agreement with that predicted from the Sablik et al. model for effect of plastic deformation on hysteresis. The intensity of the texture fibers {1 1 1}< u v w > and < 110 >//RD (RD = rolling direction) increases with the reduction. (C) 2008 Elsevier B.V. All rights reserved.

Biochemical responses of the ethylene-insensitive Never ripe tomato mutant subjected to cadmium and sodium stresses

In order to further address the known interaction between ethylene and components of the oxidative system, we have used the ethylene-insensitive Never ripe (Nr) tomato (Solanum lycopersicum L) mutant, which blocks ethylene responses. The mutant was compared to the control Micro-Tom (MT) cultivar subjected to two stressful situations: 100 mM NaCl and 0.5 mM CdCl(2). Leaf chlorophyll, lipid peroxidation and antioxidant enzyme activities in roots, leaves and fruits, and Na and Cd accumulation in tissues were determined. Although we verified a similar growth pattern and Na and Cd accumulation for MT and Nr, the mutant exhibited reduced leaf chlorophyll degradation following stress. In roots and leaves, the patterns of catalase (CAT), glutathione reductase (GR), ascorbate peroxidase (APX), guaiacol peroxidase (GPOX), superoxide dismutase (SOD) enzyme activity as well as malondialdehyde (MDA) and hydrogen peroxide (H(2)O(2)) production under the stressful conditions tested were very similar between MT and Nr mutant. However, Nr fruits showed increased H(2)O(2) production, reduced and enhanced APX activity in NaCl and CdCl(2), respectively, and enhanced GPOX in NaCl. Moreover, through non-denaturing PAGE, a similar reduction of SOD I band intensity in both, control MT and Nr mutant, treated with NaCl was observed. In leaves and fruits, a similar SOD activity pattern was observed for all periods, genotypes and treatments. Overall the results indicate that the ethylene signaling associated with NR receptor can modulate the biochemical pathways of oxidative stress in a tissue dependent manner, and that this signaling may be different following Na and Cd exposure. (C) 2011 Elsevier B.V. All rights reserved.

The isolation of antioxidant enzymes from mature tomato (cv. Micro-Tom) plants

The activity of catalase (CAT), guaiacol peroxidase (GPOX), ascorbate peroxidase (APX), glutathione reductase (GR), and the isoenzymes of superoxide dismutase (SOD) were determined in the organs of tomato (Lycopersicon esculentum) cultivar Micro-Tom after 104 days of development. The total activities of CAT, GPOX, and GR were higher in the stem than in others tissues, whereas the stem exhibited the lowest APX activity. Activity staining analysis following gel electrophoresis revealed the existence of four SOD isoenzymes in leaves, three in fruits, but only two in the roots and stems. This characterization is essential for an investigation into the effect of abiotic and biotic stresses on the oxidative stress responses by this plant model system.

Dibenzofuran degradation by Sphingomonas wittichii RW1 under environmental stresses

Sphingomonas wittichii is a gram-negative Alpha-proteobacterium, capable of degrading xenobiotic compounds such as dibenzofuran (DBF), dibenzo-p-dioxin, carbazole, 2-hydroxybiphenyl or nitro diphenyl ether herbicides. The metabolism of strain RW1 has been the subject of previous studies and a number of genes involved in DBF degradation have been characterized. It is known that RW1 posseses a unique initial DBF dioxygenase (encoded by the dxnAl gene) that catalyzes the first step in the degradation pathway. None of the organisms known to be able to degrade DBF have a similar dioxygenase, the closest match being the DBF dioxygenase from Rhodococcus sp. with an overall amino acid similarity of 45%. Genes participating in the conversion of the metabolite salicylate via the ortho-cleavage pathway to TCA cycle intermediates were identified as well. Apart from this scarce information, however, there is a lack of global knowledge on the genes that are involved in DBF degradation by strain RW1 and the influence of environmental stresses on DBF-dependent global gene expression. A global analysis is necessary, because it may help to better understand the behaviour of the strain under field conditions and suggest improvements for the current bioaugmentation practice. Chapter 2 describes the results of whole-genome analysis to characterize the genes involved in DBF degradation by RW1. Micro-array analysis allowed us to detect differences in gene transcription when strain RW1 was exposed to DBF. This was complemented by ultra-high throughput sequencing of mutants no longer capable of growing on salicylate and DBF. Some of the genes of the ortho-cleavage pathway were induced 2 to 4 times in the presence of DBF, as well as the initial DBF dioxygenase. However two gene clusters, named 4925 and 5102 were induced up to 19 times in response to DBF induction. The cluster 4925 is putatively participating in a meta-cleavage pathway while the cluster 5102 might be part of a gentisate pathway. The three pathways, ortho-cleavage, meta-cleavage and gentisate pathway seem to be active in parallel when strain RW1 is exposed to DBF, presenting evidence for a redundancy of genes for DBF degradation in the genome of RW1. Chapter 3 focuses on exploiting genetic tools to construct bioreporters representative for DBF degradation in RW1. A set of basic tools for genetic manipulation in Sphingomonas wittichii RW1 was tested and optimized. Both plasmids and mini-transposons were evaluated for their ability to be maintained in RW1 with or without antibiotic selection pressure, and for their ability to lead to fluorescent protein expression in strain RW1 from a constitutive promoter. Putative promoter regions of three of the previously found DBF-induced genes (Swit_4925, Swit_5102 and Swit_4897-dxnAl) were then used to construct eg/^-bioreporters in RW1. Chapter 4 describes the use of the constructed RW1-based bioreporter strains for examining the expression of the DBF degradation pathway genes under microcosm conditions. The bioreporter strains were first exposed to different carbon sources in liquid culture to calibrate the egfp induction. Contrary to our expectations from micro-array analysis only the construct with the promoter from gene cluster 4925 responded to DBF, whereas the other two constructs did not show specific induction with DBF. The response from the bioreporters was subsequently tested for sensitivity to water stress, given that this could have an important impact in soils. Exposure to liquid cultures with decreasing water potential, achieved by NaCl or PEG addition to the growth media, showed that eGFP expression in RW1 from the promoter regions 4925 and 5102 was not directly influenced by water stress, but only through an overall reduction in growth rate. In contrast, expression of eGFP from the dxnAl or an uspA promoter was also directly dependent on the extent of water stress. The RW1 with the 4925 construct was subsequently used in soil microcosms to evaluate DBF bioavailability to the cells in presence or absence of native microbiota or other contaminated material. We found that RW1 could grow on DBF added to soil, but bioreporter expression suggested that competition with native microbiota for DBF intermediates may limit its ability to proliferate to a maximum. Chapter 5 describes the results from the experiments carried out to more specifically detect genes of RW1 that might be implicated in water stress resistance. Hereto we created transposon mutagenesis libraries in RW1, either with a classical mini-Tn5 or with a variant that would express egfp when the transposon would insert in a gene induced under water stress. Classical mutant libraries were screened by replica plating under high and low water stress conditions (achieved by adding NaCl to the agar medium). In addition, we screened for smaller microcolonies formed by mutants in agarose beads that could be analized with flow cytometry. A number of mutants impaired to grow on NaCl-supplemented media were recovered and the transposon insertion sites sequenced. In a second procedure we screened by flow cytometry for mutants with a higher eGFP production after exposure to growth medium with higher NaCl concentrations. Mutants from both libraries rarely overlapped. Discovered gene functions of the transposon insertions pointed to compatible solute synthesis (glutamate and proline), cell membrane synthesis and modification of cell membrane composition. The results obtained in the present study give us a more complete picture of the mechanisms of DBF degradation by S. wittichii RW1, how it reacts to different DBF availability and how the DBF catabolic activity may be affected by the conditions found in contaminated environments. - Sphingomonas wittichii est une alpha-protéobactérie gram-négative, capable de dégrader des composés xénobiotiques tels que le dibenzofurane (DBF), la dibenzo-p-dioxine, le carbazole, le 2-hydroxybiphényle ou les herbicides dérivés du nitro-diphényléther. Le métabolisme de la souche RW1 a fait l'objet d'études antérieures et un certain nombre de gènes impliqués dans la dégradation du DBF ont été caractérisés. Il est connu que RW1 possède une unique dioxygénase DBF initiale (codée par le gène dxnAl) qui catalyse la première étape de la voie de dégradation. Aucun des organismes connus pour être capables de dégrader le DBF n'a de dioxygénase similaire. L'enzyme la plus proche étant la DBF dioxygénase de Rhodococcus sp. avec 45% d'acides aminés conservés. Les gènes qui participent à la transformation du salicylate en métabolites intermédiaires du cycle de Krebs par la voie ort/io-cleavage ont aussi été identifiés. Outre ces informations lacunaires, il y a un manque de connaissances sur l'ensemble des gènes impliqués dans la dégradation du DBF par la souche RW1 ainsi que l'effet des stress environnementaux sur l'expression génétique globale, en présence du DBF. Une analyse globale est nécessaire, car elle peut aider à mieux comprendre le comportement de la souche dans les conditions de terrain et de proposer des améliorations pour l'utilisation de la bio-augmentation comme technique de bio-remédiation. Le chapitre 2 décrit les résultats de l'analyse du génome pour caractériser les gènes impliqués dans la dégradation du DBF par RW1. Une analyse de micro-arrays nous a permis de détecter des différences dans la transcription des gènes lorsque la souche RW1 a été exposée au DBF. L'analyse a été complétée par le criblage à ultra-haut débit de mutants qui n'étaient plus capables de croître avec le salicylate ou le DBF comme seule source de carbone. Certains des gènes de la voie ortho-cleavage, dont la DBF dioxygénase initiale, ont xî été induits 2 à 4 fois, en présence du DBF. Cependant, deux groupes de gènes, nommés 4925 et 5102 ont été induits jusqu'à 19 fois en réponse au DBF. Le cluster 4925 participe probablement dans une voie de meta-cleavage tandis que le cluster 5102 pourrait faire partie d'une voie du gentisate. Les trois voies, ortho-cleavage, meta-cleavage et la voie du gentisate semblent être activées en parallèle lorsque la souche RW1 est exposée au DBF, ce qui représente une redondance de voies pour la dégradation du DBF dans le génome de RW1. Le chapitre 3 se concentre sur l'exploitation des outils génétiques pour la construction de biorapporteurs de la dégradation du DBF par RW1. Un ensemble d'outils de base pour la manipulation génétique dans Sphingomonas wittichii RW1 a été testé et optimisé. Deux plasmides et mini-transposons ont été évalués pour leur capacité à être maintenu dans RW1 avec ou sans pression de sélection par des antibiotiques, et pour leur capacité à exprimer la protéine fluorescente verte (eGFP) dans la souche RW1. Les trois promoteurs des gènes Swit_4925, Swit_5102 et Swit_4897 (dxnAl), induits en réponse au DBF, ont ensuite été utilisés pour construire des biorapporteurs dans RW1. Le chapitre 4 décrit l'utilisation des souches biorapportrices construites pour l'analyse de l'expression des gènes de la voie de dégradation du DBF dans des microcosmes avec différents types de sols. Les souches biorapportrices ont d'abord été exposées à différentes sources de carbone en cultures liquides afin de calibrer l'induction de la eGFP. La construction avec le promoteur du gène 4925 a permis une réponse au DBF. Mais contrairement à nos attentes, basées sur les résultats de l'analyse des micro-arrays, les deux autres constructions n'ont pas montré d'induction spécifique au DBF. La réponse des biorapporteurs a ensuite été testée pour la sensibilité au stress hydrique, étant donné que cela pourrait avoir un impact important dans les microcosmes. La diminution du potentiel hydrique en culture liquide est obtenue par addition de NaCl ou de PEG au milieu de croissance. Nous avons montré que l'expression de la eGFP contrôlée par les promoteurs 4925 et 5102 n'était pas directement influencée par le stress hydrique, mais seulement par une réduction globale des taux de croissance. En revanche, l'expression de la eGFP dépendante des promoteurs dxnAl et uspA était aussi directement dépendante de l'ampleur du stress hydrique. La souche avec la construction 4925 a été utilisée par la suite dans des microcosmes avec différents types de sols pour évaluer la biodisponibilité du DBF en présence ou absence des microbes indigènes et d'autres composés contaminants. Nous avons constaté que RW1 pouvait se développer si le DBF a été ajouté au sol, mais l'expression de la eGFP par le biorapporteur suggère que la compétition avec la microbiota indigène pour les métabolites intermédiaires du DBF peut limiter sa capacité à proliférer de manière optimale. Le chapitre 5 décrit les résultats des expériences réalisées afin de détecter spécifiquement les gènes de RW1 qui pourraient être impliquées dans la résistance au stress hydrique. Ici on a crée des bibliothèques de mutants de RW1 par transposon, soit avec un mini-Tn5 classique ou avec une variante qui exprime la eGFP lorsque le transposon s'insère dans un gène induit par le stress hydrique. Les bibliothèques de mutants ont été criblées par la méthode classique de repiquage sur boîtes, dans des conditions de stress hydrique élevé (obtenu par l'addition de NaCl dans les boîtes). En outre, nous avons criblé des micro¬colonies dans des billes d'agarose qui ont pu être analysées par cytométrie de flux. Un certain nombre de mutants déficients à croître sur des milieux supplémentés avec du NaCl ont été isolés et les sites d'insertion du transposon séquencés. Dans une deuxième procédure nous avons criblé par cytométrie de flux des mutants avec une production de eGFP supérieure, après exposition à un milieu de croissance avec une concentration élevée de NaCl. Les mutants obtenus dans les deux bibliothèques n'étaient pas similaires. Les fonctions des gènes où se trouvent les insertions de transposons sont impliqués dans la synthèse de solutés compatibles (glutamate et de la proline), dans la synthèse de la membrane cellulaire et dans la modification de la composition de la membrane cellulaire. Les résultats obtenus dans la présente étude nous donnent une image plus complète des mécanismes de dégradation du DBF par S. wittichii RW1, comment cette souche réagit à la disponibilité du DBF et comment l'activité catabolique peut être affectée par les conditions rencontrées dans des environnements contaminés.

A Practical Micro Mechanical Model Based Local Approach Methodology for the Analysis of Ductile Fracture of Welded T-Joints

This thesis concentrates on developing a practical local approach methodology based on micro mechanical models for the analysis of ductile fracture of welded joints. Two major problems involved in the local approach, namely the dilational constitutive relation reflecting the softening behaviour of material, and the failure criterion associated with the constitutive equation, have been studied in detail. Firstly, considerable efforts were made on the numerical integration and computer implementation for the non trivial dilational Gurson Tvergaard model. Considering the weaknesses of the widely used Euler forward integration algorithms, a family of generalized mid point algorithms is proposed for the Gurson Tvergaard model. Correspondingly, based on the decomposition of stresses into hydrostatic and deviatoric parts, an explicit seven parameter expression for the consistent tangent moduli of the algorithms is presented. This explicit formula avoids any matrix inversion during numerical iteration and thus greatly facilitates the computer implementation of the algorithms and increase the efficiency of the code. The accuracy of the proposed algorithms and other conventional algorithms has been assessed in a systematic manner in order to highlight the best algorithm for this study. The accurate and efficient performance of present finite element implementation of the proposed algorithms has been demonstrated by various numerical examples. It has been found that the true mid point algorithm (a = 0.5) is the most accurate one when the deviatoric strain increment is radial to the yield surface and it is very important to use the consistent tangent moduli in the Newton iteration procedure. Secondly, an assessment of the consistency of current local failure criteria for ductile fracture, the critical void growth criterion, the constant critical void volume fraction criterion and Thomason's plastic limit load failure criterion, has been made. Significant differences in the predictions of ductility by the three criteria were found. By assuming the void grows spherically and using the void volume fraction from the Gurson Tvergaard model to calculate the current void matrix geometry, Thomason's failure criterion has been modified and a new failure criterion for the Gurson Tvergaard model is presented. Comparison with Koplik and Needleman's finite element results shows that the new failure criterion is fairly accurate indeed. A novel feature of the new failure criterion is that a mechanism for void coalescence is incorporated into the constitutive model. Hence the material failure is a natural result of the development of macroscopic plastic flow and the microscopic internal necking mechanism. By the new failure criterion, the critical void volume fraction is not a material constant and the initial void volume fraction and/or void nucleation parameters essentially control the material failure. This feature is very desirable and makes the numerical calibration of void nucleation parameters(s) possible and physically sound. Thirdly, a local approach methodology based on the above two major contributions has been built up in ABAQUS via the user material subroutine UMAT and applied to welded T joints. By using the void nucleation parameters calibrated from simple smooth and notched specimens, it was found that the fracture behaviour of the welded T joints can be well predicted using present methodology. This application has shown how the damage parameters of both base material and heat affected zone (HAZ) material can be obtained in a step by step manner and how useful and capable the local approach methodology is in the analysis of fracture behaviour and crack development as well as structural integrity assessment of practical problems where non homogeneous materials are involved. Finally, a procedure for the possible engineering application of the present methodology is suggested and discussed.

Influence of optimized lubrication-cooling and minimum quantity lubrication on the cutting forces, on the geometric quality of the surfaces and on the micro-structural integrity of hardened steel parts

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Zirconia-based dental crown to support a removable partial denture: a three-dimensional finite element analysis using contact elements and micro-CT data

Veneer fracture is the most common complication in zirconia-based restorations. The aim of this study was to evaluate the mechanical behavior of a zirconia-based crown in a lower canine tooth supporting removable partial denture (RPD) prosthesis, varying the bond quality of the veneer/coping interface. Microtomography (μCT) data of an extracted left lower canine were used to build the finite element model (M) varying the core material (gold core - MAu; zirconia core - MZi) and the quality of the veneer/core interface (complete bonded - MZi; incomplete bonded - MZi-NL). The incomplete bonding condition was only applied for zirconia coping by using contact elements (Target/Contact) with 0.3 frictional coefficients. Stress fields were obtained using Ansys Workbench 10.0. The loading condition (L = 1 N) was vertically applied at the base of the RPD prosthesis metallic support towards the dental apex. Maximum principal (σmax) and von Mises equivalent (σvM) stresses were obtained. The σmax (MPa) for the bonded condition was similar between gold and zirconia cores (MAu, 0.42; MZi, 0.40). The incomplete bonded condition (MZi-NL) raised σmax in the veneer up to 800% (3.23 MPa) in contrast to the bonded condition. The peak of σvM increased up to 270% in the MZi-NL. The incomplete bond condition increasing the stress in the veneer/zirconia interface.

Laser Shock Micro-Forming as an Emerging Technique for Microsystems Shaping and Adjustment

Continuous and long-pulse lasers have been extensively used for the forming of metal sheets for macroscopic mechanical applications. However, for the manufacturing of Micro-Mechanical Systems (MMS), the applicability of such type of lasers is limited by the long relaxation time of the thermal fields responsible for the forming phenomena. As a consequence, the final sheet deformation state is attained only after a certain time, what makes the generated internal residual stress fields more dependent on ambient conditions and might difficult the subsequent assembly process. The use of short pulse (ns) lasers provides a suitable parameter matching for the laser forming of an important range of sheet components used in MEMS. The short interaction time scale required for the predominantly mechanic (shock) induction of deformation residual stresses allows the successful processing of components in a medium range of miniaturization (particularly important according to its frequent use in such systems). In the present paper, Laser Shock Micro-Forming (LSμF) is presented as an emerging technique for Microsystems parts shaping and adjustment along with a discussion on its physical foundations and practical implementation possibilities developed by the authors.

Time-Resolved Micro PIV in the Pivoting Area of the Triflo Mechanical Heart Valve

The Lapeyre-Triflo FURTIVA valve aims at combining the favorable hemodynamics of bioprosthetic heart valves with the durability of mechanical heart valves (MHVs). The pivoting region of MHVs is hemodynamically of special interest as it may be a region of high shear stresses, combined with areas of flow stagnation. Here, platelets can be activated and may form a thrombus which in the most severe case can compromise leaflet mobility. In this study we set up an experiment to replicate the pulsatile flow in the aortic root and to study the flow in the pivoting region under physiological hemodynamic conditions (CO = 4.5 L/min / CO = 3.0 L/min, f = 60 BPM). It was found that the flow velocity in the pivoting region could reach values close to that of the bulk flow during systole. At the onset of diastole the three valve leaflets closed in a very synchronous manner within an average closing time of 55 ms which is much slower than what has been measured for traditional bileaflet MHVs. Hot spots for elevated viscous shear stresses were found at the flanges of the housing and the tips of the leaflet ears. Systolic VSS was maximal during mid-systole and reached levels of up to 40 Pa.

The study of thermal stresses in a single long elastic fiber embedded in an infinite matrix

This work considered the micro-mechanical behavior of a long fiber embedded in an infinite matrix. Using the theory of elasticity, the idea of boundary layer and some simplifying assumptions, an approximate analytical solution was obtained for the normal and shear stresses along the fiber. The analytical solution to the problem was found for the case when the length of the embedded fiber is much greater than its radius, and the Young's modulus of the matrix was much less than that of the fiber. The analytical solution was then compared with a numerical solution based on Finite Element Analysis (FEA) using ANSYS. The numerical results showed the same qualitative behavior of the analytical solution, serving as a validation tool against lack of experimental results. In general this work provides a simple method to determine the thermal stresses along the fiber embedded in a matrix, which is the foundation for a better understanding of the interaction between the fiber and matrix in the case of the classical problem of thermal-stresses.

Ihwg-μnir: A Miniaturised Near-infrared Gas Sensor Based On Substrate-integrated Hollow Waveguides Coupled To A Micro-nir-spectrophotometer.

A miniaturised gas analyser is described and evaluated based on the use of a substrate-integrated hollow waveguide (iHWG) coupled to a microsized near-infrared spectrophotometer comprising a linear variable filter and an array of InGaAs detectors. This gas sensing system was applied to analyse surrogate samples of natural fuel gas containing methane, ethane, propane and butane, quantified by using multivariate regression models based on partial least square (PLS) algorithms and Savitzky-Golay 1(st) derivative data preprocessing. The external validation of the obtained models reveals root mean square errors of prediction of 0.37, 0.36, 0.67 and 0.37% (v/v), for methane, ethane, propane and butane, respectively. The developed sensing system provides particularly rapid response times upon composition changes of the gaseous sample (approximately 2 s) due the minute volume of the iHWG-based measurement cell. The sensing system developed in this study is fully portable with a hand-held sized analyser footprint, and thus ideally suited for field analysis. Last but not least, the obtained results corroborate the potential of NIR-iHWG analysers for monitoring the quality of natural gas and petrochemical gaseous products.

Estudo por espectroscopia micro-Raman dos mecanismos de separação de fase em vidros fosfatos de metais de transição

Glass-ceramics are prepared by controlled separation of crystal phases in glasses, leading to uniform and dense grain structures. On the other hand, chemical leaching of soluble crystal phases yields porous glass-ceramics with important applications. Here, glass/ceramic interfaces of niobo-, vanado- and titano-phosphate glasses were studied by micro-Raman spectroscopy, whose spatial resolution revealed the multiphase structures. Phase-separation mechanisms were also determined by this technique, revealing that interface composition remained unchanged as the crystallization front advanced for niobo- and vanadophosphate glasses (interface-controlled crystallization). For titanophosphate glasses, phase composition changed continuously with time up to the equilibrium composition, indicating a spinodal-type phase separation.