Phytochemical characterization of essential oil from Ocimum selloi

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Yield and phytochemical characterization of essential oil from Ocimum selloi B. obtained by hydrodistillation and supercritical fluid extraction

The yield and chemical composition of essential oils from leaves of Ocimum selloi B. submitted to organic and mineral fertilization, obtained by hydrodistillation and supercritical fluid extraction (SFE) were compared. Essential oil was extracted in a Clevenger-type apparatus for 2 h 30 min and analyzed by GC-MS (Shimadzu, QP 5050-DB-5 capillary column - 30 m × 0.25 mm × 0.25 μm). Carrier gas was helium (1.7 ml/min); split ratio: 1:30. Temperature program: 50°C, rising to 180°C at 5°C/min, 180°C, rising to 280°C at 10°C/min. Injector temperature: 240°C and detector temperature: 230°C. Identifications of chemical compounds were made by matching their mass spectra and Kovat's indices (IK) values with known compounds reported in the literature. An Applied Separations-apparatus (Speed SFE, model 7071, Allentown, PA, EUA) was used for SFE extractions. They were conducted at pressure 200 bar and temperature 30°C (20 min in static mode and 40 min in dynamic mode). The supercritical CO2 flow rate was (6.8±0.7)×10-5 kg-CO2/s. The essential oil collected was immersed in ethylene glycol bath (5°C). The yield of essential oils obtained by SFE was larger than hydrodistillation in both fertilization treatments (279 and 333% for organic and mineral fertilizations, respectively). There were no differences between the fertilization treatments. The amount of the volatile components showed by GC-MS chromatogram was highest in the essential oil obtained by hydrodistillation than SFE. The main volatile constituents of the essential oils were trans-anethole (Hydrodistillation: organic - 52.4%; mineral - 55.0%/ SFE: Hydrodistillation - 62.8%; mineral - 66.8%) and methyl-chavicol (Hydrodistillation: organic - 37.3%; mineral - 38.3%/ SFE: organic - 8.4%; mineral - 4.3%). A reduction of methyl-chavicol relative proportion of essential oil obtained by SFE was observed. Cys-anethole, α-copaene, trans-cariofilene, germacrene-D, β-selinene, biciclogermacrene and spathulenol were expressed only in hydrodistillation. The extraction of essential oil by SFE presented larger yield of essential oil than hydrodistillation technique, presenting, however, these essential oils, different phytochemical profiles.

Composição química e toxicidade de óleos essenciais para o pulgão-verde Schizaphis graminum (Rondani, 1852)

Este trabalho teve como objetivo identificar e quantificar os constituintes dos óleos essenciais de Illicum verum, Ageratum conyzoides, Piper hispidinervum e Ocotea odorifera, bem como avaliar a toxicidade para o pulgão-verde Schizaphis graminum. A qualificação dos constituintes foi realizada por meio de um cromatógrafo gasoso + espectrômetro de massas, e a quantificação, por um cromatógrafo gasoso + detector de ionização de chama, ambos com uma coluna DB5. O método de hidrodestilação promoveu um rendimento (p/p) de 3,81% para I. verum, 0,46% para A. conyzoides, 2,85% para P. hispidinervum e 0,68% para O. odorífera. Já os componentes majoritários foram: precoceno (87,0%) e (E)-cariofileno (7,1%) para A. conyzoides; (E)-anetol (90,4%), limoneno (2,6%) e metil-chavicol (1,3%) para I. verum; metil-eugenol (81,2%) e safrol (10,6%) para Ocotea odorífera; e safrol (82,5%) e α-terpinoleno (13,4%) para P. hispidinervum. Pelos testes de toxicidade aguda (24 horas) com folhas de sorgo ou papel-filtro contaminados, verificou-se que o óleo de A. conyzoides foi o mais tóxico para o pulgão, com CL50 de 7,13 e 7,08 µL óleo/cm2 respectivamente, seguido por O. odorifera com CL50 de 11,80 e 103,00 µL óleo/cm2 respectivamente; I. verum de 51,80 µL óleo/cm2 em ambos os substratos; e o menos tóxico foi o óleo essencial de P. hispidinervum, com CL50 de 62,50 e 143,00 µL óleo/cm2, respectivamente. Dessa maneira, sugere-se que o uso dos óleos essenciais pode representar uma nova ferramenta em programas de manejo integrado de pragas.

Effect Of Daily Use Of An Enzymatic Denture Cleanser On Candida Albicans Biofilms Formed On Polyamide And Poly(methyl Methacrylate) Resins: An In Vitro Study.

Candida biofilms on denture surfaces are substantially reduced after a single immersion in denture cleanser. However, whether this effect is maintained when dentures are immersed in cleanser daily is unclear. The purpose of this study was to evaluate the effect of the daily use of enzymatic cleanser on Candida albicans biofilms on denture base materials. The surfaces of polyamide and poly(methyl methacrylate) resin specimens (n=54) were standardized and divided into 12 groups (n=9 per group), according to study factors (material type, treatment type, and periods of treatment). Candida albicans biofilms were allowed to form over 72 hours, after which the specimens were treated with enzymatic cleanser once daily for 1, 4, or 7 days. Thereafter, residual biofilm was ultrasonically removed and analyzed for viable cells (colony forming units/mm(2)) and enzymatic activity (phospholipase, aspartyl-protease, and hemolysin). Factors that interfered with the response variables were analyzed by 3-way ANOVA with the Holm-Sidak multiple comparison method (α=.05). Polyamide resin presented more viable cells of Candida albicans (P<.001) for both the evaluated treatment types and periods. Although enzymatic cleansing significantly (P<.001) reduced viable cells, daily use did not maintain this reduction (P<.001). Phospholipase activity significantly increased with time (P<.001) for both materials and treatments. However, poly(methyl methacrylate) based resin (P<.001) and enzymatic cleansing treatment (P<.001) contributed to lower phospholipase activity. Aspartyl-protease and hemolysin activities were not influenced by study factors (P>.05). Although daily use of an enzymatic cleanser reduced the number of viable cells and phospholipase activity, this treatment was not effective against residual biofilm over time.

The Effect Of Poly(methyl Methacrylate) Surface Treatments On The Adhesion Of Silicone-based Resilient Denture Liners.

Different surface treatment protocols of poly(methyl methacrylate) have been proposed to improve the adhesion of silicone-based resilient denture liners to poly(methyl methacrylate) surfaces. The purpose of this study was to evaluate the effect of different poly(methyl methacrylate) surface treatments on the adhesion of silicone-based resilient denture liners. Poly(methyl methacrylate) specimens were prepared and divided into 4 treatment groups: no treatment (control), methyl methacrylate for 180 seconds, acetone for 30 seconds, and ethyl acetate for 60 seconds. Poly(methyl methacrylate) disks (30.0 × 5.0 mm; n = 10) were evaluated regarding surface roughness and surface free energy. To evaluate tensile bond strength, the resilient material was applied between 2 treated poly(methyl methacrylate) bars (60.0 × 5.0 × 5.0 mm; n = 20 for each group) to form a 2-mm-thick layer. Data were analyzed by 1-way ANOVA and the Tukey honestly significant difference tests (α = .05). A Pearson correlation test verified the influence of surface properties on tensile bond strength. Failure type was assessed, and the poly(methyl methacrylate) surface treatment modifications were visualized with scanning electron microscopy. The surface roughness was increased (P < .05) by methyl methacrylate treatment. For the acetone and ethyl acetate groups, the surface free energy decreased (P < .05). The tensile bond strength was higher for the methyl methacrylate and ethyl acetate groups (P < .05). No correlation was found regarding surface properties and tensile bond strength. Specimens treated with acetone and methyl methacrylate presented a cleaner surface, whereas the ethyl acetate treatment produced a porous topography. The methyl methacrylate and ethyl acetate surface treatment protocols improved the adhesion of a silicone-based resilient denture liner to poly(methyl methacrylate).

Hydrolysis of methyl benzoate from Piper arboreum by Naupactus bipes beetle

A new natural product was isolated from Piper arboreum (Piperaceae) leaves, the methyl 3-geranyl-4-hydroxybenzoate (1). The metabolism of P. arboreum leaves by Naupactus bipes beetle (Germar, 1824 - Coleoptera: Curculionidae) led to the hydrolysis of 1 to 3-geranyl-4-hydroxybenzoic acid (2). The structures of both compounds were determined based on spectroscopic analysis (¹H and 13C NMR, MS, and IR).

Clean preparation of methyl esters in one-step oxidative esterification of primary alcohols catalyzed by supported gold nanoparticles

Methyl esters were prepared by the clean, one-step catalytic esterification of primary alcohols using molecular oxygen as a green oxidant and a newly developed SiO(2)-supported gold nanoparticle catalyst. The catalyst was highly active and selective in a broad range of pressure and temperature. At 3 atm O(2) and 130 degrees C benzyl alcohol was converted to methyl benzoate with 100% conversion and 100% selectivity in 4 h of reaction. This catalytic process is much ""greener"" than the conventional reaction routes because it avoids the use of stoichiometric environmentally unfriendly oxidants, usually required for alcohol oxidation, and the use of strong acids or excess of reactants or constant removal of products required to shift the equilibrium to the desired esterification product.

1-Furoyl-3-methyl-3-phenylthiourea

The title compound, C13H12N2O2S, crystallizes with two independent molecules in the asymmetric unit. The two molecules differ in the conformation of the thiocarbonyl and carbonyl groups, and show the typical geometric parameters of substituted thiourea derivatives. The crystal structure is mainly stabilized by intermolecular N-H center dot center dot center dot O hydrogen bonding.

3-Nitrobenzoic acid-3-methyl-4-nitropyridine 1-oxide (1/1)

The title adduct, C(7)H(5)NO(4)center dot C(6)H(6)N(2)O(3), forms part of an ongoing study of the design of non-centrosymmetric systems based on 3-methy-4-nitropyridine 1-oxide. The components of the adduct are linked by intermolecular O-H center dot center dot center dot O hydrogen bonds. The rings of the two components are nearly planar, with a dihedral angle of 11.9 (2)degrees between the planes. The supramolecular structure shows that molecules of the title complex are linked into sheets by a combination of strong O-H center dot center dot center dot O and weak C-H center dot center dot center dot O hydrogen bonds.

5-Methyl-2,4-bis(methylsulfanyl)tricyclo[6.2.1.0(2,7)]undeca-4,9-diene-3,6-dione

The structure analysis of the title compound, C(14)H(16)O(2)S(2), shows the SMe and H atoms of the bond linking the six-membered rings to be syn and also to be syn to the bridgehead -CH(2)- group. Each of the five-membered rings adopts an envelope conformation at the bridgehead -CH(2)- group. The dione-substituted ring adopts a folded conformation about the 1,4-C center dot center dot center dot C vector, with the ketone groups lying to one side. The cyclohexene ring adopts a boat conformation.

4-Methyl-3-(2-phenoxyacetyl)-5-phenyl-1,3,4-oxadiazinan-2-one

The 1,3,4-oxadiazinane ring in the title compound, C(18)H(18)N(2)O(4), is in a twisted boat conformation. The two carbonyl groups are orientated towards the same side of the molecule. The dihedral angle between the planes of the benzene rings is 76.6 (3)degrees. Molecules are sustained in the three-dimensional structure by a combination of C-H center dot center dot center dot O, C-H center dot center dot center dot pi and pi-pi [shortest centroid-centroid distance = 3.672 (6) angstrom] interactions.

(5R)-3-(2-Chloroacetyl)-4-methyl-5phenyl-1,3,4-oxadiazinan-2-one

The 1,3,4-oxadiazinan-2-one ring in the title compound, C(12)H(13)ClN(2)O(3), is in a distorted half-chair conformation. The phenyl and chloroacetyl groups occupy axial and equatorial positions, respectively, and lie to the opposite side of the molecule to the N-bound methyl substituent. Molecules are consolidated in the crystal structure by C-H center dot center dot center dot O interactions.

1-Methyl-3-phenylsulfonyl-2-piperidone

The piperidone ring in the title compound, C12H15NO3S, has a slightly distorted half-chair conformation with the methyl, carbonyl and phenylsulfonyl ring substituents occupying equatorial, equatorial and axial positions, respectively. Molecules are connected into centrosymmetric dimers via C-H center dot center dot center dot O interactions and these associate into layers via C-H center dot center dot center dot O-S contacts. Further C-H center dot center dot center dot O interactions involving both the carbonyl and sulfonyl O atoms consolidate the crystal packing by providing connections between the layers.

2-Bromo-2-methyl-N-p-tolylpropanamide

In the title molecule, C(11)H(14)BrNO, there is twist between the mean plane of the amide group and the benzene ring [C(=O)-N-C...;C torsion angle = -31.2 (5)degrees]. In the crystal, intermolecular N-H...O and weak C-H...O hydrogen bonds link molecules into chains along [100]. The methyl group H atoms are disordered over two sets of sites with equal occupancy.

2-Bromo-2-methyl-N-(4-nitrophenyl)propanamide

The title compound, C(10)H(11)BrN(2)O(3), exhibits a small twist between the amide residue and benzene ring [the C-N-C-C torsion angle = 12.7 (4)degrees]. The crystal structure is stabilized by weak N-H center dot center dot center dot O, C-H center dot center dot center dot Br and C-H center dot center dot center dot O interactions. These lead to supramolecular layers in the bc plane.