Degradation in seawater of structural adhesives for hybrid fibre-metal laminated materials

The adhesives used for applications in marine environments are subject to particular chemical conditions, which are mainly characterised by an elevated chlorine ion content and intermittent wetting/drying cycles, among others.These conditions can limit the use of adhesives due to the degradation processes that they experience. In this work, the chemical degradation of two different polymers, polyurethane and vinylester, was studied in natural seawater under immersion for different periods of time.The diffusion coefficients and concentration profiles of water throughout the thickness of the adhesiveswere obtained.Microstructural changes in the polymer due to the action of water were observed by SEM, and the chemical degradation of the polymer was monitored with the Fourier transform infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC). The degradation of the mechanical properties of the adhesive was determined by creep tests withMixed Cantilever Beam (MCB) specimens at different temperatures. After 180 days of immersion of the specimens, it was concluded that the J-integral value (depending on the strain) implies a loss of stiffness of 51% and a decrease in the failure load of 59% for the adhesive tested.

Lamellenwerkzeuge mit konturfolgender Kuehlung für Spritzguss- und Schaeumwerkzeuge

Die Verkürzung der Zeit von der Produktidee bis zur Markteinführung wird für Unternehmen in nahezu allen Branchen zunehmend zum Wettbewerbsfaktor. Fertigungsverfahren, bei denen kein Material abgetragen sondern aufgebaut wird, können in diesem Zusammenhang ein Alternative zur konventionellen Fertigung darstellen. Ein generatives Verfahren, welches besonders zur schnellen Fertigung von Prototypwerkzeugen mit Kantenlängen größer 300 mm geeignet ist, ist das Metal Laminated Tooling (MELATO®). Bei diesem Verfahren werden komplex geformte Werkzeuge aus Stahlblechzuschnitten zusammengesetzt und in Abhängigkeit vom Anwendungsgebiet kraft- oder stoffschlüssig verbunden. Das Fraunhofer-Institut für Werkstoff- und Strahltechnik (IWS) in Dresden arbeitet gemeinsam mit industriellen Partnern aus den Gebieten Werkzeug- und Anlagenbau sowie Softwareentwicklung und Sensorik an einer Automatisierungslösung für das Schneiden, Paketieren und Fügen von Blechzuschnitten. Damit soll die Fertigungszeit großer Werkzeuge von derzeit etwa 12 Wochen auf eine Woche verkürzt werden. Neben der Anwendung im Bereich der Präge- oder Tiefziehwerkzeuge ist das Verfahren prädestiniert für die Herstellung von Spritzgusswerkzeugen mit konturfolgenden Kühlkanälen. Die Darstellung der Prozesskette, möglicher Verbindungstechnologien und realisierte Anwendungen sind Gegenstand des vorliegenden Beitrages.

Robust control applied to metal spraying for rapid tooling

The spray forming process is a novel method of rapidly manufacturing tools and dies for stamping and injection operations. The process sprays molten tool steel from a set of arc spray guns onto a ceramic former to build up a thick steel shell. The volumetric contraction that occurs as the steel cools is offset by a volumetric expansion taking place within the sprayed steel, which allows the dimensional accurate tools to be produced. To ensure that the required phase transformation takes place, the temperature of the steel is regulated during spraying. The sprayed metal acts both as a source of mass and a source of heat and by adjusting the rate at which metal is sprayed; the surface temperature profile over the surface of the steel can be controlled. The temperature profile is measured using a thermal imaging camera and regulated by adjusting the rate at which the guns spray the steel. Because the temperature is regulated by adjusting the feed rate to an actuator that is moving over the surface, this is an example of mobile control, which is a class of distributed parameter control. The dynamic system has been controlled using a PI controller before. The paper describes the application of H∞ tracking type controller as the desire was for the average temperature to follow a desired profile. A study on the controllability of the underlying system was aimed at.

Dynamic-response of a laminated plate with friction damping

Bulk forming of sheet metal

Ever increasing demands on functional integration of high strength light weight products leads to the development of a new class of manufacturing processes. The application of bulk forming processes to sheet or plate semi-finished products, sometimes in combination with conventional sheet forming processes creates new products with the requested properties. The paper defines this new class of sheet-bulk metal forming processes, gives an overview of the existing processes belonging to this class, highlights the tooling aspects as well as the resulting product properties and presents a short summary of the relevant work that has been done towards modeling and simulation. © 2012 CIRP.

Application of bending under tension test to determine the effect of tool radius and the contact pressure on the coefficient of friction in sheet metal forming

To quantify the frictional behaviour in sheet forming operations, several laboratory experiments which simulate the real forming conditions are performed. The Bending Under Tension Test is one such experiment which is often used to represent the frictional flow of sheet material around a die or a punch radius. Different mathematical representations are used to determine the coefficient of friction in the Bending Under Tension Test. In general the change in the strip thickness in passing over the die radius is neglected and the radius of curvature to thickness ratio is assumed to be constant in these equations. However, the effect of roller radius, sheet thickness and the surface pressure are also omitted in some of these equations. This work quantitatively determined the effect of roller radius and the tooling pressure on the coefficient of friction. The Bending Under Tension Test was performed using rollers with different radii and also lubricants with different properties. The tool radii were found to have a direct influence in the contact pressure. The effect of roller radius on friction was considerable and it was observed that there is a clear relationship between the contact pressure and the coefficient of friction.

Acoustic condition monitoring for cold metal forming

One of the most important objectives of cold metal forming research is to develop techniques that enable better manufacturing efficiencies. Within this monitoring of tooling condition is vital to providing high quality manufacturing. The objective of this research is to determine the signature derived from Acoustic Emission (AE) sensors, in order to establish the current condition of a machine tool, as applied to bolt-making. From here we aim to develop and implement an on-line condition monitoring tool for the cold forming process. A review of the literature has shown that much research into AE has been successfully applied in metal cutting operations; such as milling, drilling and turning, but little research has been done related to metal forming. This appears to be due to the complexity of obtaining consistent signals using Acoustic Emission systems, because the presence of noise in many forms. This paper will detail many of the AE signals acquired and analysed through our research. The extensive results indicate this form of condition monitoring is not suitable for metal forming in its current configuration. Further tests are proposed to enable such research to move forward, so a condition monitoring system can be established.

Investigation on the forming behaviour of metal/polymer laminates

A metal/polymer laminate is a new light weight sheet material suitable to replace conventional steel or aluminium sheet in future car designs. In this study the effect of material composition and process conditions on the forming behaviour of metal/polymer laminates in sheet metal forming was investigated by experimental, analytical and numerical methods.

Modelling of tooling wear in trim dies for AHSS

Using Advanced High Strength Steels (AHSS) in forming and cutting dies generates higher loads in tools. Tool wear is an issue when applying AHSS. This study investigates the effect of process parameters such as clearance, material properties and punch/die bluntness on contact pressure values and tool wear. Some desirable process parameters that minimise wear have been found.

Characterising material and process variation effects on springback robustness for a semi-cylindrical sheet metal forming process

Variation in the incoming sheet material and fluctuations in the press setup is unavoidable in many stamping plants. The effect of these variations can have a large influence on the quality of the final stamping, in particular, unpredictable springback of the sheet when the tooling is removed. While stochastic simulation techniques have been developed to simulate this problem, there has been little research that connects the influence of the noise sources to springback. This paper characterises the effect of material and process variation on the robustness of springback for a semi-cylindrical channel forming operation, which shares a similar cross-section profile as many automotive structural components. The study was conducted using the specialised sheet metal forming package AutoForm^TM Sigma, for which a series of stochastic simulations were performed with each of the noise sources incrementally introduced. The effective stress and effective strain scatter in a critical location of the part was examined and a response window, which indicates the respective process robustness, was defined. The incremental introduction of the noise sources allows the change in size of the stressstrain response window to be tracked. The results showed that changes to process variation parameters, such as BHP and friction coefficient, directly affect the strain component of the stressstrain response window by altering the magnitude of external work applied to forming system. Material variation, on the other hand, directly affected the stress component of the response window. A relationship between the effective stressstrain response window and the variation in springback was also established.

Analytical solutions and finite element modelling of deep drawing process for cylindrical metal cups

Analytical modelling of deep drawing process is of value in preliminary process design to illustrate the influence of major variables including friction and strain hardening on punch loads, cup dimensions and process limits. In this study, analytical models including theoretical solution and a series of finite element models are developed to account for the influences of process parameters including friction coefficient, tooling geometry and material properties on deep drawing of metal cups. The accuracy of both the theoretical and finite element solutions is satisfactory compared with those from experimental work.