Estudo experimental e teórico das propriedades magnéticas e supercondutoras dos compostos borocarbetos da série Y(Ni 1-x Mn x) 2 B2 C com x = 0,0, 0,01, 0,025, 0,05, 0,10 e 0,15

Apresentamos neste trabalho os resultados de um estudo experimental e teórico dos compostos borocarbetos supercondutores da série Y(Ni1-xMnx)2B2C com x = 0; 0,01; 0,025; 0,05; 0,10; 0,15. A principal motivação para este trabalho foi investigar a estrutura eletrônica e a possível formação do momento magnético sobre os átomos de impureza de Mn nos compostos Y(Ni1- xMnx)2B2C. O aparecimento do momento magnético localizado no sítio da impureza possibilitou estudar a influência do Mn sobre o mecanismo de quebra de pares supercondutores e sobre as propriedades magnéticas do composto. Os borocarbetos são compostos de estrutura cristalina tetragonal de corpo centrado e altamente anisotrópicos (c/a~3). São intermetálicos de alta temperatura crítica supercondutora Tc, com forte acoplamento elétron-fonon. Em alguns casos podem apresentar ordem magnética, supercondutividade e também coexistência ou competição energética entre ambos. As medidas de transporte eletrônico, em função da temperatura, foram feitas utilizando-se um detector síncroton baseado na técnica de quatro pontos operando na faixa de 4,2K até 300K. Essas medidas possibilitaram o estudo das propriedades relacionadas ao transporte eletrônico na fase supercondutora. Na fase normal, extraiu-se a dependência em energia da função espectral de fonons α² F (ω) para alguns compostos da série estudada. As medidas magnéticas em função da temperatura e do campo magnético foram feitas utilizando-se um SQUID (Superconducting Quantun Interference Device – Quantun Design Model MPMS XL). Tais medidas permitiram a caracterização das propriedades magnéticas de nossas amostras. Em particular determinou-se o valor, em regime de saturação, do momento magnético associado ao sítio cristalino do Mn. Foram determinadas também as correntes críticas supercondutoras usando o Modelo de estado crítico de Bean e a variação da temperatura crítica supercondutora (Tc) com a mudança do campo externo aplicado. As medidas magnéticas permitiram a obtenção do diagrama que relaciona o campo crítico inferior (HC1) e a temperatura, variando-se a concentração do átomo dopante de manganês. Foi feito um esforço teórico no sentido de interpretar os resultados experimentais. Para isso foram usados três modelos: O modelo de estado crítico de Bean já citado acima e um modelo baseado na fórmula de Ziman usando uma aproximação para a função espectral de fonons para descrever a resistividade no regime de alta temperatura. Além disto, usou-se o modelo de duas sub-redes para a descrição do momento magnético das impurezas de Mn, em função da concentração, na série Y(Ni ) ( 2 ω α F 1-xMnx)2B2C.

Efeito da moagem de alta energia na microestrutura e nas propriedades magnéticas do compósito wc-10%p.Co

This work a studied the high energy milling effect in microstructure and magnetic properties of the WC-10wt.%Co composite. The composite powders were prepared by mechanical mixed and milled at 2 hours, 100 hours, 200 hours and 300 hours in planetary milling. After this process the composite were compacted in stainless steel die with cylindrical county of 10 mm of diameter, at pressure 200 Mpa and sintered in a resistive furnace in argon atmosphere at 1400 oC for 5 min. The sintered composite were cutted, inlaid, sandpapered, and polished. The microestrutural parameters of the composite was analyzed by X-ray diffraction, scanning electronic microscopy, optical microscopy, hardness, magnetic propriety and Rietveld method analyze. The results shows, with milling time increase the particle size decrease, it possibility minor temperature of sintering. The increase of milling time caused allotropic transformation in cobalt phase and cold welding between particles. The cold welding caused the formation of the particle composite. The X-ray diffraction pattern of composite powders shows the WC peaks intensity decrease with the milling time increase. The X-ray diffraction pattern of the composite sintered samples shows the other phases. The magnetic measurements detected a significant increase in the coercitive field and a decrease in the saturation magnetization with milling time increase. The increase coercitive field it was also verified with decrease grain size with milling time increase. For the composite powders the increase coercitive field it was verified with particle size reduction and saturation magnetization variation is relate with the variation of free cobalt. The Rietveld method analyze shows at milling time increase the mean crystalline size of WC, and Co-cfc phases in composite sintered sample are higher than in composite powders. The mean crystallite size of Co-hc phase in composite powders is higher than in composite sintered sample. The mean lattice strains of WC, Co-hc and Co-cfc phases in composite powders are higher than in composite sintered samples. The cells parameters of the composite powder decrease at milling time increase this effect came from the particle size reduction at milling time increase. In sintered composite the cells parameters is constant with milling time increase

Propriedades magnéticas quase-estáticas de filmes ferromagnéticos amorfos de FeCuNbSiB

Today, one of the topics that attracts interest of the scientific community is the understanding of magnetic properties of magnetic systems with reduced dimensions, in particular, ferromagnetic thin films. In this case, the comprehension and control of these properties, as well as the development of routes to obtain them, are crucial issues in many aspects of current and future technologies for storage and transmission of information in the electro-electronic industry. There are several materials that exhibit soft magnetic properties, and we highlight the amorphous alloys and that ones obtained by partial crystallization, so-called nanocrystalline materials. The production of these alloys as magnetic ribbons is very common in scientific and technological area, but there are just a few works related to the production of these alloys as thin films. In this work, we studied the quasi-static magnetic properties of ferromagnetic thin films based on FeCuNbSiB in a wide range of thicknesses, from 20 to 500 nm, produced by sputtering. In particular, after the structural characterization performed via X-ray diffraction, the magnetic properties of the sets of samples were investigated using experimental magnetization curve, obtained using a vibrating sample magnetometer, as well as through theoretical curves obtained by theoretical modeling and numerical computation. The modeling process is based on the Stoner Wohlfarth model applied to three dimensions, and adds some energy terms, using as reference experimental results of magnetization. In this case, from the comparison between theoretical and experimental results and the analysis of the constant anisotropy behavior as a function of film thickness, we aim to obtain further information on the magnetization process of the samples, to identify routes for the production of thin films and develop a theoretical to films to use it, in the future, in the obtainment of the theoretical curves of some magnetic measurements, such as magnetoimpedance and magnetoresistance

Síntese análise das propriedades magnéticas da ferrita de NiMg e características de absorção de radiação

It was synthesized different Ni1-xMgxFe2O4 (0,2 ≤ x ≤ 0,7) compositions by use of citrate precursor method. Initially, the precursory citrates of iron, nickel and magnesium were mixed and homogenized. The stoichiometric compositions were calcined from 350°C to 1200°C at ambient atmosphere or in argon atmosphere. The calcined powders were characterized by XRD, TGA/DTG, FTIR, magnetic measures and reflectivity using the wave guide method. I was observed pure magnetic phase formation between 350°C and 500°C, with formation of ferrite and hematite after 600°C at ambient atmosphere. The calcined powder at argon atmosphere formed pure ferromagnetic phase at 1100°C and 1200°C. The Rietveld analyses calculated the cations level occupation and the crystallite size. The analyses obtained nanometric crystals (11-66 nm), that at 900°C/3h presents micrometric sizes (0,45 - 0,70 Om). The better magnetization results were 54 Am2/Kg for x= 0,2 composition, calcined at 350°C/3h and 30 min, and 55,6 Am2/Kg for x= 0,2 1200°C, calcined in argon. The hysteresis shows characteristics of soft magnetic material. Two magnetization processes were considered, superparamagnetism at low temperature and the magnetic domains formation at high temperatures. The materials presented absorption less or equal the 50 % in ranges specific frequency. As for the 2,0 and 3,0 thickness (in 11,0 - 11,8 GHz), the reflectivity of the x= 0,3, 0,5 and 0,4 compositions, all calcined at 900°C/3h showed agreement with MS and O. Various factors contribute for the final radiation absortion effect, such as, the particle size, the magnetization and the polymer characteristics in the MARE composition. The samples that presented better magnetization does not obtaining high radiation absorption. It is not clear the interrelaction between the magnetization and the radiation absorption in the strip of frequencies studied (8,2 - 12,4 GHz)

Estudo das características magnéticas e absorvedoras das ferritas de nizn, niznmn, mnzn, nimg, nicuzn e nicuznmg obtidas via método do citrato precursor

Were synthesized systems Ni0,5Zn0,5Fe2O4, i0,2Zn0,5Mn0,3Fe2O4, Mn0,5Zn0,5Fe2O4, Ni0,5Mg0,5Fe2O4, Ni0,2Cu0,3Zn0,5Fe2O4 and Ni0,2Cu0,3Zn0,5Mg0,08Fe2O4, the precursors citrate method. The decomposition of the precursors was studied by thermogravimetric analysis and spectroscopy in the infrared region, the temperature of 350°C/3h. The evolution of the phases formed after calcinations at 350, 500, 900 and 1100ºC/3h was accompanied by X-ray diffraction using the Rietveld refinement to better identify the structures formed. The materials were also analyzed by scanning electron microscopy, magnetic measurements and analysis of the reflectivity of the material. The samples calcined at different temperatures showed an increase of crystallinity with increasing calcination temperature, verifying that for some compositions at temperatures above 500°C precipitates of second phase such as hematite and CuO. The compositions of manganese present in the structure diffusion processes slower due to the ionic radius of manganese is greater than for other ions substitutes, a fact that delays the stabilization of spinel structure and promotes the precipitation of second phase. The compositions presented with copper precipitation CuO phase at a temperature of 900 and 1100ºC/3h This occurs according to the literature because the concentration of copper in the structure is greater than 0.25 mol%. The magnetic measurements revealed features of a soft ferrimagnetic material, resulting in better magnetic properties for the NiZn ferrite and NiCuZnMg at high temperatures. The reflectivity measurements showed greater absorption of electromagnetic radiation in the microwave band for the samples calcined at 1100ºC/3h, which has higher crystallite size and consequently the formation of multi-domain, increasing the magnetization of the material. The results of absorption agreed with the magnetic measurements, indicating among the ferrites studied, those of NiZn and NiCuZnMg as better absorbing the incident radiation.

Síntese e caracterização de ferritas de níquel dopadas com cobalto e efeito da substituição nas suas propriedades magnéticas

The ferrite composition Ni1 - xCoxFe2O4 (0 ≤ x ≤ 0.75) were obtained by the method of microwave assisted synthesis and had their structural and magnetic properties evaluated due to the effect of the substitution of Ni by Co. The compounds were prepared: according to the concept of chemical propellants and heated in the microwave oven with power 7000kw. The synthesized material was characterized by absorption spectroscopy in the infrared (FTIR), Xray diffraction (XRD) using the Rietveld refinement, specific surface area (BET) , scanning electron microscopy (SEM) with aid of energy dispersive analysis (EDS) and magnetic measurements (MAV). The results obtained from these techniques confirmed the feasibility of the method of synthesis employed to obtain the desired spinel structure, the ferrite, nickel ferrite as for nickel doped with cobalt. The results from XRD refinement ally showed the formation of secondary phases concerning stages α - Fe2O3, FeO, (FeCo)O e Ni0. On the other hand, there is an increase in crystallite size with the increase of cobalt in systems, resulting in an increased crystallinity. The results showed that the BET systems showed a reduction in specific surface area with the increase of cobalt and from the SEM, the formation of irregular porous blocks and that the concentration of cobalt decreased the agglomerative state of the system. The magnetic ferrites studied showed different characteristics according to the amount of dopant used, ranging from a very soft magnetic material (easy magnetization and demagnetization ) - for the system without cobalt - a magnetic material with a little stiffer behavior - for systems containing cobalt. The values of the coercive field increased with the increasing growth of cobalt, and the values of saturation magnetization and remanence increased up to x = 0,25 and then reduced. The different magnetic characteristics presented by the systems according to the amount of dopant used, allows the use of these materials as intermediates magnetic

Fases magnéticas em compostos Er'Co IND. x''Mn IND. 1-x''O IND> 3+ou - δ'

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Propriedades estruturais, ópticas e magnéticas de filmes de GaMnN

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Nanopartículas magnéticas de 'FE''CO'@'AU': preparação, caracterização e funcionalização com complexo de 'RU'(II) luminescente

Pós-graduação em Química - IQ

Efeito da moagem de alta energia na microestrutura e nas propriedades magnéticas do compósito wc-10%p.Co

This work a studied the high energy milling effect in microstructure and magnetic properties of the WC-10wt.%Co composite. The composite powders were prepared by mechanical mixed and milled at 2 hours, 100 hours, 200 hours and 300 hours in planetary milling. After this process the composite were compacted in stainless steel die with cylindrical county of 10 mm of diameter, at pressure 200 Mpa and sintered in a resistive furnace in argon atmosphere at 1400 oC for 5 min. The sintered composite were cutted, inlaid, sandpapered, and polished. The microestrutural parameters of the composite was analyzed by X-ray diffraction, scanning electronic microscopy, optical microscopy, hardness, magnetic propriety and Rietveld method analyze. The results shows, with milling time increase the particle size decrease, it possibility minor temperature of sintering. The increase of milling time caused allotropic transformation in cobalt phase and cold welding between particles. The cold welding caused the formation of the particle composite. The X-ray diffraction pattern of composite powders shows the WC peaks intensity decrease with the milling time increase. The X-ray diffraction pattern of the composite sintered samples shows the other phases. The magnetic measurements detected a significant increase in the coercitive field and a decrease in the saturation magnetization with milling time increase. The increase coercitive field it was also verified with decrease grain size with milling time increase. For the composite powders the increase coercitive field it was verified with particle size reduction and saturation magnetization variation is relate with the variation of free cobalt. The Rietveld method analyze shows at milling time increase the mean crystalline size of WC, and Co-cfc phases in composite sintered sample are higher than in composite powders. The mean crystallite size of Co-hc phase in composite powders is higher than in composite sintered sample. The mean lattice strains of WC, Co-hc and Co-cfc phases in composite powders are higher than in composite sintered samples. The cells parameters of the composite powder decrease at milling time increase this effect came from the particle size reduction at milling time increase. In sintered composite the cells parameters is constant with milling time increase

Propiedades magnetoelásticas de aleaciones feromagnéticas con memoria de forma

Las aleaciones metamagnéticas pertenecen a las aleaciones ferromagnéticas con memoria de forma (FSMA). Estas aleaciones presentan los efectos de memoria de forma de las propias FSMA y otras características como la magnetorresistencia, los efectos magnetocalóricos y magnetocalóricos inversos que las hacen de gran interés para diversas aplicaciones. Estos efectos se debe a la caída de la imanación entre la fase austenita ferromagnética y la martensita durante la transición estructural. El carácter magnético de la fase austenita es conocido debido a varios experimentos que se han llevado a cabo, pero en el caso de la fase martensita está aún sin concretar habiendo varias opciones posibles. Es de vital importancia conocer el comportamiento magnético de la fase martensita para aplicaciones futuras de las aleaciones metamagnéticas. En este trabajo se ha estudiado la aleación Ni50Mn36In14 (T2B) la cual ha sido sometida a medidas magnéticas con el fin de acercarnos más al conocimiento del carácter magnético de estas aleaciones y concretar la temperatura de Curie mediante un estudio de los exponentes críticos de los “Arrott Plot generalizados”. Mediante el estudio de los exponentes críticos se obtienen estos resultados: Austenita: β=0.2 y γ=1.5. TCA=300.7 K Martensita: β=0.2 y γ=1.5. TCM=202 K II

Studies on magnetocaloric and magnetic coupling effects

O presente trabalho apresenta novas metodologias desenvolvidas para a análise das propriedades magnéticas e magnetocalóricas de materiais, sustentadas em considerações teóricas a partir de modelos, nomeadamente a teoria de transições de fase de Landau, o modelo de campo médio molecular e a teoria de fenómeno crítico. São propostos novos métodos de escala, permitindo a interpretação de dados de magnetização de materiais numa perspectiva de campo médio molecular ou teoria de fenómeno crítico. É apresentado um método de estimar a magnetização espontânea de um material ferromagnético a partir de relações entropia/magnetização estabelecidas pelo modelo de campo médio molecular. A termodinâmica das transições de fase magnéticas de primeira ordem é estudada usando a teoria de Landau e de campo médio molecular (modelo de Bean-Rodbell), avaliando os efeitos de fenómenos fora de equilíbrio e de condições de mistura de fase em estimativas do efeito magnetocalórico a partir de medidas magnéticas. Efeitos de desordem, interpretados como uma distribuição na interacção magnética entre iões, estabelecem os efeitos de distribuições químicas/estruturais nas propriedades magnéticas e magnetocalóricas de materiais com transições de fase de segunda e de primeira ordem. O uso das metodologias apresentadas na interpretação das propriedades magnéticas de variados materiais ferromagnéticos permitiu obter: 1) uma análise quantitativa da variação de spin por ião Gadolínio devido à transição estrutural do composto Gd5Si2Ge2, 2) a descrição da configuração de cluster magnético de iões Mn na fase ferromagnética em manganites da família La-Sr e La-Ca, 3) a determinação dos expoentes críticos β e δ do Níquel por métodos de escala, 4) a descrição do efeito da pressão nas propriedades magnéticas e magnetocalóricas do composto LaFe11.5Si1.5 através do modelo de Bean-Rodbell, 5) uma estimativa da desordem em manganites ferromagnéticas com transições de segunda e primeira ordem, 6) uma descrição de campo médio das propriedades magnéticas da liga Fe23Cu77, 7) o estudo de efeitos de separação de fase na família de compostos La0.70-xErxSr0.30MnO3 e 8) a determinação realista da variação de entropia magnética na família de compostos de efeito magnetocalórico colossal Mn1-x-yFexCryAs.

Systematic studies on 3d-3d and 3d-4f multimetallic complexes with interesting magnetic and/or luminescent properties

324 p.

Estágios iniciais da eletrodeposição de cobalto e níquel acompanhados por EC-STM e EC-AGFM

Neste trabalho foram eletrodepositados filmes ultrafinos de cobalto e níquel sobre substrato de Au/mica. Os estágios iniciais da deposição foram acompanhados in-situ pelo uso das técnicas de EC-STM (microscopia de varredura por tunelamento – modo eletroquímico) e EC-AGFM (magnetome tria de força de gradiente de campo alternado – modo eletroquímico), que se constitui em uma nova técnica para avaliação de propriedades magnéticas de filmes ultrafinos eletrodepositados. Como resultado, foi obtido o comportamento eletroquímico do eletrodo de Au/mica em meios contendo cobalto ou níquel, acrescidos ou não, dos aditivos: sacarina e tiouréia e a caracterização magnética dos filmes formados. Os dados obtidos por EC-STM revelaram a estrutura dos filmes de cobalto e níquel em baixa espessura (algumas monocamadas). A deposição de cobalto inicia com uma bicamada e o crescimento continua quase camada por camada. Para o caso do níquel o modo de crescimento está associado ao potencial aplicado: filmes crescidos em –1,1VMSE apresentaram nucleação instantânea, enquanto para –1,2VMSE foi observada nucleação progressiva. Pela análise dos dados obtidos por EC-AGFM, foi possível relacionar a estrutura dos filmes as suas propriedades magnéticas. Foi encontrada anisotropia magnética perpendicular somente para os filmes de cobalto em torno de 1,3ML de espessura. O efeito dos aditivos sacarina e tiouréia nas medidas magnéticas também foi estudado.

Estudo da viabilização do uso da mistura híbrida ferrocarbonila / ferrita de NI0,5Zn0,5Fe2o4 como material absorvedor de radiação eletromagnética

Were synthesized ferrites of NiZn on systems Ni0,5Zn0,5Fe2O4, the precursors citrate method. The decomposition of the precursors was studied by thermogravimetric analysis and spectroscopy in the infrared region, the temperature of 350°C/3h. The evolution of the phases formed after calcinations at 350ºC/3h, 600, 1000 and 1100ºC/2h was accompanied by X-ray diffraction using the Rietveld refinement method for better identification os structures formed. Was observed for samples calcined at different temperatures increased crystallinity with increasing calcination temperature, being observed for the samples calcined at 900 and 1100 º C/2h was the precipitation of a secondary phase, the phase hematite. The ferrocarbonila of industrial origin was analyzed by X-ray diffraction and Rietveld for the identification of its structure. The carbonyl iron was added NiZn ferrite calcined at 350ºC/3h, 600, 900, 1000 and 1100ºC/2h to the formation of hybrid mixtures. They were then analyzed by Xray diffraction and Rietveld. The NiZn ferrite and ferrocarbonila as well as the hybrid mixtures were subjected to analysis of scanning electron microscopy, magnetic measurements and reflectivity. The magnetic measurements indicated that the ferrite, the ferrocarbonila, as well as hybrid mixtures showed characteristics of soft magnetic material. The addition of ferrocarbonila in all compositions showed an increase in the results of magnetic measurements and reflectivity. Best result was observed in the increase of the magnetization for the hybrid mixture of Ferrocarbonila / ferrite of NiZn calcined at 600ºC/2h. The mixture Ferrocarbonila / ferrite calcined 1000°C/2h presented better absorption of electromagnetic radiation in the microwave