Mechanical properties and energy absorption of ceramic particulate and resin-impregnation reinforced aluminium foams

The mechanical properties of aluminium foams can be improved by matrix reinforcement and resin-impregnation methods. In the present study, aluminium foams were reinforced by both ceramic particulate reinforcing of the aluminium matrix and resin-impregnating pores. The mechanical properties and the energy absorption of the reinforced aluminium foams were investigated by dynamic and quasi-static compression. Results indicated that the ceramic particle additions of CBN, SiC and B4C in aluminium foams increase the peak stress, elastic modulus and energy absorption of the aluminium foams, under both conditions of dynamic and quasi-static compression. Moreover, the aluminium foams with and without ceramic particle additions exhibited obvious strain rate sensitivity during dynamic compression. Furthermore, the resin-impregnation improves the mechanic properties and energy absorption of aluminium foams significantly. However, aluminium foams with resin-impregnation showed negligible strain rate sensitivity under dynamic compression. It is reported that both the ceramic particle addition and resin-impregnation can be effective techniques to improve the mechanical and the energy absorption properties of aluminium foams.

Impact and energy absorption of road safety barriers by coupled SPH/FEM

Road safety barriers are used to minimise the severity of road accidents and protect lives and property. There are several types of barrier in use today. This paper reports the initial phase of research carried out to study the impact response of portable water-filled barrier (PWFB) which has the potential to absorb impact energy and hence provide crash mitigation under low to moderate speeds. Current research on the impact and energy absorption capacity of water-filled road safety barriers is limited due to the complexity of fluid-structure interaction under dynamic impact. In this paper, a novel fluid-structure interaction method is developed based on the combination of Smooth Particle Hydrodynamics (SPH) and Finite Element Method (FEM). The sloshing phenomenon of water inside a PWFB is investigated to explore the energy absorption capacity of water under dynamic impact. It was found that water plays an important role in energy absorption. The coupling analysis developed in this paper will provide a platform to further the research in optimising the behaviour of the PWFB. The effect of the amount of water on its energy absorption capacity is investigated and the results have practical applications in the design of PWFBs.

Impact and energy absorption of portable water-filled road safety barrier system fitted with foam

Portable water-filled barriers (PWFBs) are roadside appurtenances that are used to prevent errant vehicles from penetrating into temporary construction zones on roadways. A numerical model of the composite PWFB, consisting of a plastic shell, steel frame, water and foam was developed and validated against results from full scale experimental tests. This model can be extended to larger scale impact cases, specifically ones that include actual vehicle models. The cost-benefit of having a validated numerical model is significant and this allows the road barrier designer to conduct extensive tests via numerical simulations prior to standard impact tests Effects of foam cladding as additional energy absorption material in the PWFB was investigated. Different types of foam were treated and it was found that XPS foam was the most suitable foam type. Results from this study will aid PWFB designers in developing new generation of roadside structures which will provide enhanced road safety.

Energy absorption behaviours of CSM-based GFRC plates with hemispherical features

In the present study, the mechanical behaviour of CSM (chopped strand mat)-based GFRC (glass fibre-reinforced composite) plates with single and multiple hemispheres under compressive loads has been investigated both experimentally and numerically. The basic stress-strain behaviours arc identified with quasi-static tests on two-ply coupon laminates and short cylinders, and these are followed up with compressive tests in a UTM (universal testing machine) on single- and multiple-hemisphere plates. The ability of an explicit LS-DYNA solver in predicting the complex material behaviour of composite hemispheres, including failure, is demonstrated. The relevance and scalability of the present class of structural components as `force-multipliers' and `energy-multipliers' have been justified by virtue of findings that as the number of hemispheres in a panel increased from one to four, peak load and average absorbed energy rose by factors of approximately four and six, respectively. The performance of a composite hemisphere has been compared to similar-sized steel and aluminium hemispheres, and the former is found to be of distinctly higher specific energy than the steel specimen. A simulation-based study has also been carried out on a composite 2 x 2-hemisphere panel under impact loads and its behaviour approaching that of an ideal energy absorber has been predicted. In summary, the present investigation has established the efficacy of composite plates with hemispherical force multipliers as potential energy-absorbing countermeasures and the suitability of CAE (computer-aided engineering) for their design.

Tailoring energy absorption capacity of CNT forests through application of electric field

This study examines the effect of electric field on energy absorption capacity of carbon nanotube forests (CNTFs), comprising of vertically aligned multiwalled carbon nanotubes, under both quasistatic (strain rate, (epsilon) over dot = 10(-3) s(-1)) and dynamic ((epsilon) over dot = similar to 10(3) s(-1)) loading conditions. Under quasistatic condition, the CNTFs were cyclically loaded and unloaded while electric field was applied along the length of carbon nanotube (CNT) either throughout the loading cycle or explicitly during either the loading or the unloading segment. The energy absorbed per cycle by CNTF increased monotonically with electric field when the field was applied only during the loading segment: A 7 fold increase in the energy absorption capacity was registered at an electric field of 1 kV/m whereas no significant change in it was noted for other schemes of electro-mechanical loading. The energy absorption capacity of CNTF under dynamic loading condition also increased monotonically with electric field; however, relative to the quasistatic condition, less pronounced effect was observed. This intriguing strain rate dependent effect of electric field on energy absorption capacity of CNTF is explained in terms of electric field induced strengthening of CNTF, originating from the time dependent electric field induced polarization of CNT. (C) 2015 Elsevier Ltd. All rights reserved.

The plastic collapse and energy absorption capacity of egg-box panels

The plastic collapse response of aluminium egg-box panels subjected to out-of-plane compression has been measured and modelled. It is observed that the collapse strength and energy absorption are sensitive to the level of in-plane constraint, with collapse dictated either by plastic buckling or by a travelling plastic knuckle mechanism. Drop weight tests have been performed at speeds of up to 6 m s-1, and an elevation in strength with impact velocity is noted. A 3D finite element shell model is needed in order to reproduce the observed behaviours. Additional calculations using an axisymmetric finite element model give the correct collapse modes but are less accurate than the more sophisticated 3D model. The finite element simulations suggest that the observed velocity dependence of strength is primarily due to strain-rate sensitivity of the aluminium sheet, with material inertia playing a negligible role. Finally, it is shown that the energy absorption capacity of the egg-box material is comparable to that of metallic foams. © 2003 Elsevier Ltd. All rights reserved.

Investigation into channel angular extrusion and the UREAD energy absorption technique

.

Compressive properties and energy absorption of hollow sphere aluminium

Manufactured cellular aluminums have been developed for a wide range of automotive applications where weight savings, improved safety, crashworthiness and comfort are required. The plateau deformation behavior of cellular aluminums under compressive loading makes this new class of lightweight materials suitable for energy absorption and comes close to ideal impact absorbers. In the present study, aluminum hollow hemispheres were firstly processed by pressing. Hollow sphere aluminum samples with a body-centered cubic (BCC) packing were then fabricated by bonding together single hollow spheres, which were prepared by adhering together hollow hemispheres. Hollow sphere aluminum samples with various kinds of sphere wall thicknesses of 0.1 mm, 0.3 mm and 0.5 mm but the same outside diameter of 4 mm were investigated by compressive tests. The effects of the sphere wall thickness on the mechanical properties and energy absorption characteristics were investigated.

Compressive behavior and energy absorption of constructed cellular aluminum

The defoThe deformation behaviors and energy absorption characteristics of constructed cellular aluminums were investigated by compressive tests. Constructed cellular aluminum specimens with two kinds of thickness in the cold-pressed panel and various numbers of layers bonded together have been tested. The plateau stress and the energy absorption have been measured and furthermore, the deformation behaviors have been evaluated. Results indicate that superior mechanical properties with constructed cellular aluminums can be achieved when the distribution of material at cell level is properly selected. Excellent energy absorption per unit mass can be obtained by only changing the thickness of the original aluminum sheet.nnation behaviors and energy absorption characteristics of constructed cellular aluminums were investigated by compressive tests. Constructed cellular aluminum specimens with two kinds of thickness in the cold-pressed panel and various numbers of layers bonded together have been tested. The plateau stress and the energy absorption have been measured and furthennore, the defonnation behaviors have been evaluated. Results indicate that superior mechanical properties with constructed cellular aluminums can be achieved when the distribution of material at cell level is properly selected. Excellent energy absorption per unit mass can be obtained by only changing the thickness of the original aluminum sheet.

Strain rate effects on the energy absorption of rapidly manufactured composite tubes

Quasi-static and intermediate rate axial crush tests were conducted on tubular specimens of Carbon/Epoxy (Toray T700/G83C) and Glass/Polypropylene (Twintex). The quasi-static tests were conducted at 10 mm/min (1.67 x 10¯⁴ m/s); five different crush initiators were used. Tests at intermediate rates were performed at speeds of 0.25, 0.5, 0.75, 1, 2, and 4m/s. Modes of failure and specific energy absorption (SEA) values were studied. The highest SEA measured was 86 kJ/kg. This value was observed using Carbon/Epoxy samples at quasi static rates with a 45° chamfer initiator. The highest energy absorption for Twintex tubes was observed to be 57.56 kJ/kg during 45° chamfer initiated tests at 0.25 m/s. Compared with steel and aluminium, SEA values of 15 and 30 kJ/kg, respectively, the benefits of using composite materials in crash structures become apparent.