Wastewater Treatment and Deinking Sludge Utilization Possibilities for Energy and Material Recovery in the Leningrad Region

Operation of pulp and paper mills generates waste including wastewater treatment sludge and deinking sludge. Both sludge types are generated in large amounts and are mainly disposed of in landfills in the Leningrad Region resulting in environmental degradation. The thesis was aimed at seeking new sustainable ways of sludge utilization. Two paper mills operating in the Leningrad Region and landfilling their sludge were identified: “SCA Hygiene Products Russia” and “Knauf”. The former generates 150 t/day of deinking sludge, the latter – 145 t/day of secondary sludge. Chemical analyses of deinking sludge were performed to assess applicability of sludge in construction materials production processes. Higher heating value on dry basis of both sludge types was determined to evaluate energy potential of sludge generated in the Leningrad Region. Total energy output from sludge incineration was calculated. Deinking sludge could be utilized in the production process of “LSR-Cement” or “Slantsy Cement Plant Cesla” factories, and “Pobeda” and “Nikolsky” brick mills without exceeding current sludge management costs.

Industrial ecology applied to ELV management. Material and energy recovery from ASR

This PhD thesis reports on car fluff management, recycling and recovery. Car fluff is the residual waste produced by car recycling operations, particularly from hulk shredding. Car fluff is known also as Automotive Shredder Residue (ASR) and it is made of plastics, rubbers, textiles, metals and other materials, and it is very heterogeneous both in its composition and in its particle size. In fact, fines may amount to about 50%, making difficult to sort out recyclable materials or exploit ASR heat value by energy recovery. This 3 years long study started with the definition of the Italian End-of-Life Vehicles (ELVs) recycling state of the art. A national recycling trial revealed Italian recycling rate to be around 81% in 2008, while European Community recycling target are set to 85% by 2015. Consequently, according to Industrial Ecology framework, a life cycle assessment (LCA) has been conducted revealing that sorting and recycling polymers and metals contained in car fluff, followed by recovering residual energy, is the route which has the best environmental perspective. This results led the second year investigation that involved pyrolysis trials on pretreated ASR fractions aimed at investigating which processes could be suitable for an industrial scale ASR treatment plant. Sieving followed by floatation reported good result in thermochemical conversion of polymers with polyolefins giving excellent conversion rate. This factor triggered ecodesign considerations. Ecodesign, together with LCA, is one of the Industrial Ecology pillars and it consists of design for recycling and design for disassembly, both aimed at the improvement of car components dismantling speed and the substitution of non recyclable material. Finally, during the last year, innovative plants and technologies for metals recovery from car fluff have been visited and tested worldwide in order to design a new car fluff treatment plant aimed at ASR energy and material recovery.

Teräohjaimet jakopyörösahoissa

Diplomityön tavoitteena oli tutkia pyöröterän kehältä ohjauksen soveltuvuutta kaksiakselisiin jakosahoihin. Tavoitteena oli tuottaa uutta tietoa sahalaitoksen tuotantoprosessin koneiden suunnitteluun sahakonetekniikan edelleen kehittämiseksi. Työ voi myös palvella sahalaitoksia yhtenä työkaluna koneiden valinnassa tuotantoprosessin tehostamiseksi. Diplomityössä on tutkittu tekniikkaa suomalaisen sahakonevalmistajan, Veisto Oy:n näkökulmasta mutta työn tulokset ovat tarkoitettu yleisesti sovellettaviksi. Diplomityön kirjallisuusosa koostuu teräohjainjärjestelmän etujen ja haittojen kartoituksesta puuraaka-aineen käyttösuhteen, käytettävyyden, tuotantonopeuksien, kunnossapidon ja käytön näkökannoilta tarkasteltuna. Lisäksi työhön on liitetty aiheeseen kiinteästi liittyvä kirjallisuuteen ja valmistajilta saatuihin tietoihin perustuva katsaus tämän hetken pyöröterätekniikkaan. Työssä analysoidaan myös kevättalvella 2002 Itä-Kanadassa suoritettujen sahauskokeiden tuloksia. Kokeissa tutkittiin kehältä ohjatuille terille muutetun jakosahayksikön suorituskykyä ja käytettävyyttä. Tutkittava kone oli Veisto Oy:n valmistama muuttuva-asetteinen pelkkahakkuri -VDA -jakosaha, tyypiltään HewSaw R200 MSA SE.

Competence Development and Capacity Building of Sawmill Enterprises in Kenya – A Human Resources Development Approach

The Kenyan forestry and sawmilling industry have been subject to a changing environment since 1999 when the industrial forest plantations were closed down. This has lowered raw material supply and it has affected and reduced the sawmill operations and the viability of the sawmill enterprises. The capacity of the 276 registered sawmills is not sufficient to fulfill sawn timber demand in Kenya. This is because of the technological degradation and lack of a qualified labor force, which were caused because of non-existent sawmilling education and further training in Kenya. Lack of competent sawmill workers has led to low raw material recovery, under utilization of resources and loss of employment. The objective of the work was to suggest models, methods and approaches for the competence and capacity development of the Kenyan sawmilling industry, sawmills and their workers. A nationwide field survey, interviews, questionnaire and literature review was used for data collection to find out the sawmills’ competence development areas and to suggest models and methods for their capacity building. The sampling frame included 22 sawmills that represented 72,5% of all the registered sawmills in Kenya. The results confirmed that the sawmills’ technological level was backwards, productivity low, raw material recovery unacceptable and workers’ professional education low. The future challenges will be how to establish the sawmills’ capacity building and workers’ competence development. Sawmilling industry development requires various actions through new development models and approaches. Activities should be started for technological development and workers’ competence development. This requires re-starting of vocational training in sawmilling and the establishment of more effective co-operation between the sawmills and their stakeholder groups. In competence development the Enterprise Competence Management Model of Nurminen (2007) can be used, whereas the best training model and approach would be a practically oriented learning at work model in which the short courses, technical assistance and extension services would be the key functions.

Pinnoiteteollisuudessa syntyvien maalijätteiden hyötykäyttö ja uudet liiketoimintamahdollisuudet

Tämän diplomityön tavoite on kartoittaa maalien ja lakkojen valmistuksessa syntyvien sivuvirtojen hyötykäyttöä ja hyötykäyttöpotentiaalia nykyisellään. Työn tarkoitus on toimia esiselvityksenä pinnoiteteollisuuden sivuvirtojen hyötykäyttöön liittyvien liiketoimintamahdollisuuksien syvemmälle analyysille. Teollisuuden sivuvirtoihin liittyvää tietoa kerätään tilastoista ja olemassa olevista raporteista sekä haastattelemalla teollisuus- ja palveluyritysten edustajia sekä alan asiantuntijoita. Sivuvirtojen teknisten hyötykäyttömahdollisuuksien ja liiketoiminnallisten mahdollisuuksien tarkastelua varten järjestetään työpajoja asiantuntijoille Apila Group Oy Ab:n asiantuntijaverkostossa. Neljässä haastatellussa tuotantolaitoksissa syntyi vuonna 2008 yhteensä 6 662 tonnia kiinteää jätettä ja lietteitä. 68 % näistä sivuvirroista hyötykäytettiin energiana tai polttoaineen valmistuksessa. Materiaalina sivuvirtoja hyötykäytettiin 16 % sivuvirroista, pääasiassa pahvia, paperia, metalleja sekä tynnyreitä ja kontteja. Myös merkittävä osa liuottimista otettiin talteen uudelleenhyödyntämistä varten. Tässä diplomityössä hyötykäyttömahdollisuuksien tarkempaa tarkastelua varten valittiin tavanomaisiksi jätteiksi luokiteltuja maalisivuvirtoja, joita haastatelluissa tuotantolaitoksissa syntyi noin 1 500 tonnia. Maalisivuvirtojen tärkeimmät materiaaliominaisuudet liittyvät niiden sisältämiin täyte- ja sideaineisiin, jotka muodostavat merkittävän osan maalien koostumuksesta. Selvityksen mukaan nämä ominaisuudet voidaan ottaa hyötykäyttöön erilaisissa yhdistelmämateriaaleissa, esimerkiksi ekstruusiopuristetuissa tai ahtopuristetuissa muovikuitukomposiiteissa. Komposiittien raaka-aineena käytetään jo erilaisia sivuvirtoja ja lisäksi erilaisten komposiittien markkinoiden ennustetaan kasvavan. Tämä voi tarjota mahdollisuuksia uusille palvelu-, t&k- tai tuotteistusliiketoiminnoille. Kuivilla maalijätteillä on myös hyvä lämpöarvo, jolloin energiahyötykäytön ja palamisjäännöksen materiaalihyötykäytön yhdistäminen mm. keramiikka- tai sementtiteollisuudessa voi tarjota mahdollisuuksia uusille liiketoiminnoille.

Kierrätyspolttoainemarkkinat Euroopassa

Työn tavoitteena oli selvittää Saksan, Ruotsin ja Suomen kierrätyspolttoaineen valmistusta ja käyttöä sekä kierrätyspolttoainemarkkinoita. Kierrätyspolttoaineiden käyttöä ja valmistusta sekä kierrätyspolttoainemarkkinoita säädellään tarkastelumaissa EU-lainsäädännöllä ja kansallisilla lainsäädännöillä jätteistä, jätteenpoltosta ja materiaalikierrätyksestä sekä CEN/TC 343-toimikunnan standardeilla kiinteille kierrätyspolttoaineille. Työn johtopäätöksenä on, että kierrätyspolttoainemarkkinat ovat tarkastelumaissa hyvin ulkoapäin ohjautuvat ja markkinaehtoista tasapainoa ei ehdi syntyä. Tarkastelumaiden markkinat ovat erilaiset, Saksassa kierrätyspolttoaineiden käyttö ja valmistus on pitkälle kehittynyttä, tiheää ja monipuolista, Ruotsissa yhteisen termistön puuttuminen kertoo alan hajanaisuudesta. Saksassa ja Ruotsissa kierrätyspolttoainemarkkinoiden kasvamiseen ovat vaikuttaneet kaatopaikkakiellot. Suomessa tähän asti pelkkään rinnakkaispolttoon perustuneet kierrätyspolttoainemarkkinat ovat vasta vakiintumassa. Kierrätyspolttoainemarkkinat tulevat kansainvälistymään ja kilpailu materiaalista tulee kovenemaan. Standardien käyttöönotto tulee olemaan helpointa Suomessa, jossa kierrätyspolttoaineen standardisoinnista on kokemusta. Suomen olisi syytä ottaa jäte- ja energiahuollon ratkaisuissa huomioon eri toimintojen aiheuttamat talous- ja ympäristövaikutukset.

Toimintaohjeistus HSY:n jätteenpolton materiaalivirtojen hallintaan

Vantaan Energia rakentaa ympäristövaatimukset täyttävän jätevoimalan Itä-Vantaan Långmossebergeniin. Jätevoimalassa tullaan käyttämään polttoaineena kierrätykseen kelpaamatonta syntypaikkalajiteltua yhdyskuntajätettä sekä maakaasua. Helsingin seudun ympäristöpalvelut -kuntayhtymä HSY tulee toimittamaan noin 80 % vuosittaisesta jätepolttoaineesta. Tässä työssä on esitetty toimintamalli HSY:n jätteenpolton materiaalivirtojen hallitsemiseksi. Toimintamallin tarkoituksena on antaa ohjeistus jätteiden materiaalivirtojen käsittelymenetelmistä ennen jätteenpolttolaitosta. Lisäksi toimintamallin tarkoituksena on saada vähennettyä pohjakuonan määrää. Toimintamalli sisältää ohjeistuksen kotitalouksien sekajätteen, pienjäteasemien sekajätteen, sekalaisen rakennus- ja purkujätteen sekä kaupan- ja teollisuuden jätteiden käsittelytavoista. Jätevirtojen koostumusta on selvitetty kirjallisuudesta löytyvien tietojen perusteella ja tietoja on täydennetty kesällä 2013 suoritetun lajittelututkimuksen tiedoilla. Tutkimuksen tuloksista selvisi, että pienjäteasemien sekajätteiden lajittelua tehostamalla HSY:llä pystytään tekemään merkittäviä taloudellisia säästöjä. Tutkimuksessa selvisi, että kipsilevy olisi kannattavinta kerätä omalle lavalleen pienjäteasemilla. Sekalaisen rakennus- ja purkujätteen osalta todettiin, että sitä ei kannata ohjata suoraan jätevoimalalle poltettavaksi, eikä sitä voida sijoittaa käsittelemättömänä kaatopaikalle vuoden 2020 jälkeen. Tästä syystä työssä on ehdotettu, että sekalainen rakennus- ja purkujäte ohjattaisiin lajittelulaitokselle käsiteltäväksi ennen sen loppusijoittamista. Tutkimuksen tulosten perusteella voidaan myös todeta, että toimintamallia noudattamalla, pohjakuonan määrää on mahdollista vähentää lähes puolella alkuperäisestä arviosta.

Deinking sludge utilization possibilities: technical, economic, and environmental assessments

This report introduces the ENPI project called “EMIR - Exploitation of Municipal and Industrial Residues” which was executed in a co-operation between Lappeenranta University of Technology (LUT), Saint Petersburg State University of Economics (SPbSUE), Saint Petersburg State Technical University of Plant Polymers (SPbSTUPP) and industrial partners from both Leningrad Region (LR), Russia and Finland. The main targets of the research were to identify the possibilities for deinking sludge management scenarios in co-operation with partner companies, to compare the sustainability of the alternatives, and to provide recommendations for the companies in the Leningrad Region on how to best manage deinking sludge. During the literature review, 24 deinking sludge utilization possibilities were identified, the majority falling under material recovery. Furthermore, 11 potential utilizers of deinking sludge were found within the search area determined by the transportation cost. Each potential utilizer was directly contacted in order to establish cooperation for deinking sludge utilization. Finally, four companies, namely, “Finnsementti” – a cement plant in Finland (S1), “St.Gobian Weber” – a light-weight aggregate plant in Finland (S2), “LSR-Cement” – a cement plant in LR (S3), and “Rockwool” – a stone wool plant in LR (S4) were seen as the most promising partners and were included in the economic and environmental assessments. Economic assessment using cost-benefit analysis (CBA) indicated that substitution of heavy fuel oil with dry deinking sludge in S2 was the most feasible option with a benefit/cost ratio (BCR) of 3.6 when all the sludge was utilized. At the same time, the use of 15% of the total sludge amount (the amount that could potentially be treated in the scenario) resulted in a BCR of only 0.16. The use of dry deinking sludge in the production of cement (S3) is a slightly more feasible option with a BCR of 1.1. The use of sludge in stone wool production is feasible only when all the deinking sludge is used and burned in an existing incineration plant. The least economically feasible utilization possibility is the use of sludge in cement production in Finland (S1) due to the high gate fee charged. Environmental assessment was performed applying internationally recognized life cycle assessment (LCA) methodologies: ISO 14040 and ISO 14044. The results of a consequential LCA stated that only S1 and S2 lead to a reduction of all environmental impacts within the impact categories chosen compared to the baseline scenario where deinking sludge is landfilled. Considering S1, the largest reduction of 13% was achieved for the global warming potential (GWP), whereas for S2, the largest decrease of abiotic depletion potential (ADP) was by 1.7%, the eutrophication potential (EP) by 1.8%, and a GWP of 2.1% was documented. In S3, the most notable increase of ADP and acidification potential (AP) by 2.6 and 1.5% was indicated, while the GWP was reduced by 12%, the largest out of all the impact categories. In S4, ADP and AP increased by 2.3 and 2.1% respectively, whereas ODP was reduced by 25%. During LCA, it was noticed that substitution of fuels causes a greater reduction of environmental impact (S1 and S2) than substitution of raw materials (S3 and S4). Despite a number of economically and environmentally acceptable deinking sludge utilization methods being assessed in the research, evaluation of bottlenecks and communications with companies’ representatives uncovered the fact that the availability of the raw materials consumed, and the risks associated with technological problems resulting from the sludge utilization, limited the willingness of industrial partners to start deinking sludge utilization. The research results are of high value for decision-makers at already existing paper mills since the result provide insights regarding alternatives to the deinking sludge utilization possibilities already applied. Thus, the research results support the maximum economic and environmental value recovery from waste paper utilization.

Mass balance of pilot-scale pretreatment of sugarcane bagasse by steam explosion followed by alkaline delignification

Five pilot-scale steam explosion pretreatments of sugarcane bagasse followed by alkaline delignification were explored. The solubilised lignin was precipitated with 98% sulphuric acid. Most of the pentosan (82.6%), and the acetyl group fractions were solubilised during pretreatment, while 90.2% of cellulose and 87.0% lignin were recovered in the solid fraction. Approximately 91% of the lignin and 72.5% of the pentosans contained in the steam-exploded solids were solubilised by delignification, resulting in a pulp with almost 90% of cellulose. The acidification of the black liquors allowed recovery of 48.3% of the lignin contained in the raw material. Around 14% of lignin, 22% of cellulose and 26% of pentosans were lost during the process. In order to increase material recovery, major changes, such as introduction of efficient condensers and the reduction in the number of washing steps, should be done in the process setup. (C) 2012 Elsevier Ltd. All rights reserved.

Twelve factors influencing sustainable recycling of municipal solid waste in developing countries

Sustainable management of solid waste is a global concern, as exemplified by the United Nations Millennium Development Goals (MDG) that 191 member states support. The seventh MDG indirectly advocates for municipal solid waste management (MSWM) by aiming to ensure environmental sustainability into countries’ policies and programs and reverse negative environmental impact. Proper MSWM will likely result in relieving poverty, reducing child mortality, improving maternal health, and preventing disease, which are MDG goals one, four, five, and six, respectively (UNMDG, 2005). Solid waste production is increasing worldwide as the global society strives to obtain a decent quality of life. Several means exist in which the amount of solid waste going to a landfill can be reduced, such as incineration with energy production, composting of organic wastes, and material recovery through recycling, which are all considered sustainable methods by which to manage MSW. In the developing world, composting is already a widely-accepted method to reduce waste fated for the landfill, and incineration for energy recovery can be a costly capital investment for most communities. Therefore, this research focuses on recycling as a solution to the municipal solid waste production problem while considering the three dimensions of sustainability environment, society, and economy. First, twenty-three developing country case studies were quantitatively and qualitatively examined for aspects of municipal solid waste management. The municipal solid waste (MSW) generation and recovery rates, as well as the composition were compiled and assessed. The average MSW generation rate was 0.77 kg/person/day, with recovery rates varying from 5 – 40%. The waste streams of nineteen of these case studies consisted of 0 – 70% recyclable material and 17 – 80% organic material. All twenty-three case studies were analyzed qualitatively by identifying any barriers or incentives to recycling, which justified the creation of twelve factors influencing sustainable municipal solid waste management (MSWM) in developing countries. The presence of regulations, enforcement of laws, and use of incentive schemes constitutes the first factor, Government Policy. Cost of MSWM operations, the budget allocated to MSWM by local to national governments, as well as the stability and reliability of funds comprise the Government Finances factor influencing recycling in the third world. Many case studies indicated that understanding features of a waste stream such as the generation and recovery rates and composition is the first measure in determining proper management solutions, which forms the third factor Waste Characterization. The presence and efficiency of waste collection and segregation by scavengers, municipalities, or private contractors was commonly addressed by the case studies, which justified Waste Collection and Segregation as the fourth factor. Having knowledge of MSWM and an understanding of the linkages between human behavior, waste handling, and health/sanitation/environment comprise the Household Education factor. Individuals’ income influencing waste handling behavior (e.g., reuse, recycling, and illegal dumping), presence of waste collection/disposal fees, and willingness to pay by residents were seen as one of the biggest incentives to recycling, which justified them being combined into the Household Economics factor. The MSWM Administration factor was formed following several references to the presence and effectiveness of private and/or public management of waste through collection, recovery, and disposal influencing recycling activity. Although the MSWM Personnel Education factor was only recognized by six of the twenty-two case studies, the lack of trained laborers and skilled professionals in MSWM positions was a barrier to sustainable MSWM in every case but one. The presence and effectiveness of a comprehensive, integrative, long-term MSWM strategy was highly encouraged by every case study that addressed the tenth factor, MSWM Plan. Although seemingly a subset of private MSWM administration, the existence and profitability of market systems relying on recycled-material throughput, involvement of small businesses, middlemen, and large industries/exporters is deserving of the factor Local Recycled-Material Market. Availability and effective use of technology and/or human workforce and the safety considerations of each were recurrent barriers and incentives to recycling to warrant the Technological and Human Resources factor. The Land Availability factor takes into consideration land attributes such as terrain, ownership, and development which can often times dictate MSWM. Understanding the relationships among the twelve factors influencing recycling in developing countries, made apparent the collaborative nature required of sustainable MSWM. Factors requiring the greatest collaborative inputs include waste collection and segregation, MSWM plan, and local recycled-material market. Aligning each factor to the societal, environmental, and economic dimensions of sustainability revealed the motives behind the institutions contributing to each factor. A correlation between stakeholder involvement and sustainability existed, as supported by the fact that the only three factors driven by all three dimensions of sustainability were the same three that required the greatest collaboration with other factors. With increasing urbanization, advocating for improved health for all through the MDG, and changing consumption patterns resulting in increasing and more complex waste streams, the utilization of the collaboration web offered by this research is ever needed in the developing world. Through its use, the institutions associated with each of the twelve factors can achieve a better understanding of the collaboration necessary and beneficial for more sustainable MSWM.

A copper-containing oxytelluride as a promising thermoelectric material for waste heat recovery

The new thermoelectric material BiOCuTe exhibits an electrical conductivity of 224 S cm-1 and a Seebeck coefficient of +186 μV K-1 at 373 K, together with an extremely low lattice thermal conductivity of ∼ 0.5 W m-1 K-1. This results in a ZT of 0.42 at 373 K, which increases to 0.66 at the maximum temperature investigated, 673 K.

Recovery and preliminary purification of Americium obtained from waste material /

"Contract AT (29-1)-1106."

Mesenchymal Stromal Cells From Adipose Tissue Attached To Suture Material Enhance The Closure Of Enterocutaneous Fistulas In A Rat Model.

Surgical treatment for enterocutaneous fistulas (EF) frequently fails. Cell therapy may represent a new approach to treatment. Mesenchymal stromal cells (MSCs) have high proliferative and differentiation capacity. This study aimed to investigate whether MSCs could adhere to suture filament (SF), promoting better EF healing. MSCs, 1 × 10(6), from adipose tissue (ATMSCs) were adhered to a Polyvicryl SF by adding a specific fibrin glue formulation. Adhesion was confirmed by confocal and scanning electron microscopy (SEM). A cecal fistula was created in 22 Wistar rats by incising the cecum and suturing the opening to the surgical wound subcutaneously with four separate stitches. The animals were randomly allocated to three groups: control (CG)-five animals, EF performed; injection (IG)-eight animals 1 × 10(6) ATMSCs injected around EF borders; and suture filament (SG): nine animals, sutured with 1 × 10(6) ATMSCs attached to the filaments with fibrin glue. Fistulas were photographed on the operation day and every 3 days until the 21st day and analyzed by two observers using ImageJ Software. Confocal and SEM results demonstrated ATMSCs adhered to SF (ATMSCs-SF). The average reduction size of the fistula area at 21st day was greater for the SG group (90.34%, P < 0.05) than the IG (71.80%) and CG (46.54%) groups. ATMSCs adhered to SF maintain viability and proliferative capacity. EF submitted to ATMSCs-SF procedure showed greater recovery and healing. This approach might be a new and effective tool for EF treatment.

Recovery and upgrading bovine rumen protein by extrusion: effect of lipid content on protein disulphide cross-linking, solubility and molecular weight

Bovine rumen protein with two levels of residual lipids (1.9 per cent or 3.8 per cent) was subjected to thermoplastic extrusion under different temperatures and moisture contents. Protein solubility in different buffers, disulphide cross-linking and molecular weight distribution were determined on the extrudates. After extrusion, samples with 1.9 per cent residual lipids content had a higher concentration of protein insoluble by undetermined forces, irrespective of feed moisture and processing temperature used. Lipid content of 3.8 per cent in the feed material resulted in more protein participating in the extrudate network through non-covalent interactions (hydrophobic and electrostatic) and disulphide bonds. A small dependency of the extrusion process on moisture and temperature and a marked dependency on lipid content, especially phospholipid, was observed, Electrophoresis under non-reducing conditions showed that protein extrusion with low feed moisture promoted high molecular breakdown inside the barrel, probably due to intense shear force, and further protein aggregation at the die end