Influence of Mg content on the microstructure and solid solution chemistry of Al-7%Si-Mg casting alloys during solution treatment

The solution treatment stage of the T6 heat-treatment of Al-7%Si-Mg foundry alloys influences microstructural features such as Mg2Si dissolution, and eutectic silicon spheroidisation and coarsening. Microstructural and microanalytical studies have been conducted across a range of Sr-modified Al-7%Si alloys, with an Fe content of 0.12% and Mg contents ranging from 0.3-0.7wt%. Qualitative and quantitative metallography have shown that, in addition to the above changes, solution treatment also results in changes to the relative proportions of iron-containing intermetallic particles and that these changes are composition-dependent. While solution treatment causes a substantial transformation of pi phase to beta phase in low Mg alloys (0.3-0.4%), this change is not readily apparent at higher Mg levels (0.6-0.7%). The pi to beta transformation is accompanied by a release of Mg into the aluminum matrix over and above that which arises from the rapid dissolution of Mg2Si. Since the level of matrix Mg retained after quenching controls an alloy's subsequent precipitation hardening response, a proper understanding of this phase transformation is crucial if tensile properties are to be maximised.

Effects of magnesium intake deficiency on bone metabolism and bone tissue around osseointegrated implants

Objectives: This study evaluated the effect of magnesium dietary deficiency on bone metabolism and bone tissue around implants with established osseointegration. Materials and methods: For this, 30 rats received an implant in the right tibial metaphysis. After 60 days for healing of the implants, the animals were divided into groups according to the diet received Control group (CTL) received a standard diet with adequate magnesium content, while test group (Mg) received the same diet except for a 90% reduction of magnesium. The animals were sacrificed after 90 days for evaluation of calcium, magnesium, osteocalcin and parathyroid hormone (PTH) serum levels and the deoxypyridinoline (DPD) level in the urine. The effect of magnesium deficiency on skeletal bone tissue was evaluated by densitometry of the lumbar vertebrae, while the effect of bone tissue around titanium implants was evaluated by radiographic measurement of cortical bone thickness and bone density. The effect on biomechanical characteristics was verified by implant removal torque testing. Results: Magnesium dietary deficiency resulted in a decrease of the magnesium serum level and an increase of PTH and DPD levels (P <= 0.05). The Mg group also presented a loss of systemic bone mass decreased cortical bone thickness and lower values of removal torque of the implants (P <= 0.01). Conclusions: The present study concluded that magnesium-deficient diet had a negative influence on bone metabolism as well as on the bone tissue around the implants.

Effects of magnesium intake deficiency on bone metabolism and bone tissue around osseointegrated implants

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Magnesium levels in nutrient solution and common bean (Phaseolus vulgaris L cv Carioca) development. Evaluation of the growth relations and assimilate partitioning

The effect of magnesium levels in nutrient solution upon relation between shoot and root, leaf weight ratio and assimilate partitioning of common bean (Phaseolus vulgaris L. cv Carioca) was studied. Bean plants (3 per pot) were grown in 6 l pots containing Hoagland & Arnon n. 2 solution modified to obtain 2.4, 24.3, 48.6, 72.9 and 97.2 ppm of magnesium. The experimental design was a completely randomized factorial replicated 3 times with 5 levels of magnesium and 5 samplings wich were done forthnightly. Therefore, it may be suggested that the 48.6 ppm of magnesium level proposed by Hoagland & Amen (1950) is the best choice for the common bean, according to the conditions of this experiment. Magnesium concentrations over 48.6 ppm didn't show significant alterations of the evaluated parameters. Nutrient solution with 2.4 ppm of magnesium content provides higher efficiency to the common bean plants during almost all its cycle, except the final of the reproductive phase. These results suggest that magnesium concentration increased to 48.6 ppm, in the cycle final perhaps could increase the productivity.

The influence of calcium and magnesium on the growth of the lichens Parmelia saxatilis and Xanthoria parietina on slate substrates

In South Gwynedd, Wales, U.K., the calcicole lichen Xanthoria parietina occurs not only on alkaline substrates at inland sites but also on siliceous rock at coastal martimie sites while the calcifuge species Parmelia saxatilis occurs only at inland sites and on slate rocks. Samples of maritime and inland slate did not differ significantly in their calcium or magnesium content. Thalli of X. parietina on pieces of slate did not survive when transplanted from maritime rocks to a site inland. Thalli of maritime X. parietina and P. saxatilis on slate were then transplanted to a site inland and were treated at intervals during 1 year either with calcium carbonate applied as a thick paste or a 0.25 mM solution of calcium chloride. Treatment of X. parietina with calcium carbonate enabled the thalli to survive and grow. However, addition of calcium carbonate to P. saxatilis resulted in low growth rates and fragmentation of the centres of the thalli. The calcium chloride solution had no statistically significant effects on the growth of either species. In addition, thalli of both species were treated with calcium or magnesium carbonates or wetted with an alkaline buffer at intervals over 12-14 months. Thalli of X. parietina survived and grew rapidly when treated with either carbonate but the growth of the buffer-treated thalli gradually declined over the experimental period. Thalli of P. saxatilis fragmented and disappeared after 8-10 months after treatment with either carbonate but normal growth occurred in the buffer treatment. Xanthoria parietina may occur on siliceous maritime rocks at the site because of the presence of calcium or magnesium in sea spray combined with the spray’s alkaline pH. By contrast, P. saxatilis may be confined to siliceous rocks inland because the thalli grow poorly in the presence of calcium and magnesium.

The effect of dissolved magnesium on diffusion creep in calcite

We experimentally tested a series of synthetic calcite marbles with varying amounts of dissolved magnesium in a standard triaxial deformation machine at 300 MPa confining pressure, temperatures between 700 and 850°C, stresses between 2 and 100 MPa, and strain rates between 10−7 and 10−3 s−1. The samples were fabricated by hot isostatic pressing of a mixture of calcite and dolomite at 850°C and 300 MPa. The fabrication protocol resulted in a homogeneous, fine-grained high-magnesian calcite aggregate with minimal porosity and with magnesium contents between 0.07 and 0.17 mol% MgCO3. At stresses below 40 MPa the samples deformed with linear viscosity that depended inversely on grain size to the 3.26±0.51 power, suggesting that the mechanisms of deformation were some combination of grain boundary diffusion and grain boundary sliding. Because small grain sizes tended to occur in the high-magnesium calcite, the strength also appeared to vary inversely with magnesium content. However, the strength at constant grain size does not depend on the amount of dissolved magnesium, and thus, the impurity effect seems to be indirect. At stresses higher than 40 MPa, the aggregates become non-linearly viscous, a regime we interpret to be dislocation creep. The transition between the two regimes depends on grain size, as expected. The activation energy for diffusion creep is 200±30 kJ/mol and is quite similar to previous measurements in natural and synthetic marbles deformed at similar conditions with no added magnesium.

Spectroscopic monitoring during laser welding of aluminium alloy

The mechanical properties of aluminium alloys are strongly influenced by the alloying elements and their concentration. In the case of aluminium alloy EN AW-6060 the main alloying elements are magnesium and silicon. The first goal of this thesis was to determine stability, repeatability and sensitivity as figures of merit of the in-situ melt identification technique. In this study the emissions from the laser welding process were monitored with a spectrometer. With the information produced by the spectrometer, quantitative analysis was conducted to determine the figures of merit. The quantitative analysis concentrated on magnesium and aluminium emissions and their relation. The results showed that the stability of absolute intensities was low, but the normalized magnesium emissions were quite stable. The repeatability of monitoring magnesium emissions was high (about 90 %). Sensitivity of the in-situ melt identification technique was also high. As small as 0.5 % change in magnesium content was detected by the spectrometer. The second goal of this study was to determine the loss of mass during deep penetration laser welding. The amount of magnesium in the material was measured before and after laser welding to determine the loss of magnesium. This study was conducted for aluminium alloy with nominal magnesium content of 0-10 % and for standard material EN AW-6060 that was welded with filler wire AlMg5. It was found that while the magnesium concentration in the material changed, the loss of magnesium remained fairly even. Also by feeding filler wire, the behaviour was similar. Thirdly, the reason why silicon had not been detected in the emission spectrum needed to be explained. Literature research showed that the amount of energy required for silicon to excite is considerably higher compared to magnesium. The energy input in the used welding process is insufficient to excite the silicon atoms.

Sorption of oxadiazon in soils cultivated in the brazilian cerrado

The objective of this study was to evaluate oxadiazon sorption in different soils of the Brazilian Cerrado, highlighting the correlations of lethal doses of this herbicide capable of inhibiting 50% of the dry matter accumulation of the bio-indicator (LD50) among the chemical characteristics of the soil and its direct and indirect effects. The experiment was carried out in a greenhouse in a randomized block design and four repetitions. Each experimental unit consisted of a pot with increasing rates of oxadiazon and oat (Avena sativa), as the bio-indicator species. For sorption evaluation, washed sand and 22 soils (substrates) from Cerrado Brazilian's Alliaceae cultivated areas were used. LD50 and sorption ratio (SR) = [(LD50soil - LD50sand)/LD50sand] to the substrates were determined. Pearson correlation analysis was performed between the chemical characteristics of the substrates and the LD50 of oxadiazon. A path analysis was quantified, to deploy only the significant correlations estimated in direct and indirect effects of the characters on LD50, which is a basic variable. A more pronounced LD50 (528.09 g ha-1) for the Cerrado soil sample resulted in higher SR (> 53.00), while in the washed sand substrate, LD50 corresponded only to 9.74 g ha-1 of the oxadiazon (available in soil). It was concluded that oxadiazon sorption is influenced by the chemical characteristics of the soils, highlighting the correlation with pH (CaCl2), magnesium content, aluminum, organic matter, organic carbon, and aluminum saturation.

Influencia de doses de potássio nos teores de macronutrientes em plantas e sementes de alface

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influence of biosolids rate on chemical properties of an oxisol in São Paulo, Brazil

Organic residues may cause major health and environmental problems. This is the case in our study area, where more than 10 billion L per year of residential and industrial waste are produced. Land application of biosolids can be an economical solution by recycling waste and can provide valuable fertilizer if used correctly. The aim of this work was to study the effect of biosolids on the chemical properties of an Oxisol. The experiment was located at Ilha Solteira northwest of São Paulo State, Brazil. The soil was cropped to Sorghum bicolor.The field experimental design consisted of random blocks with six treatments and four replications of each treatment. Biosolids were surface applied to four treatments at rates of 5, 10, 20, and 40 Mg ha(-1) on a dry matter basis; in addition, a treatment with mineral fertilizer and a control were included. One year after biosolids application, soil samples were taken at 0-10, 10-20, and 20-40 cm. Organic matter content (Walkley-Black) and pH (CaCl2) were routinely determined. Cation exchange capacity, exchangeable bases (Ca, Mg, K), and P were determined by exchange resin extraction. No significant differences in any of the analyzed properties were found below the 20 cm depth. Extractable phosphorus (P) and potassium (K) increased with increasing biosolids rate in the top 20 cm, whereas calcium (Ca) and (Ma) magnesium content were not significantly influenced by biosolids. Soil pH decreased with increasing biosolids application. The sewage sludge application did not influence the sorghum production in the first year of culture, under unfavorable soil moisture conditions, but it influenced the dry matter.

Correção da sodicidade de dois solos irrigados em resposta à aplicação de gesso agrícola

The chemical and physical degradation of the soils by salinity and sodicity problems constitutes a serious obstacle in productive irrigated areas in arid and semi-add regions. In order to eval mate the effect of gypsum on electrical conductivity, pH, exchangeable sodium percentage, sodium, calcium and magnesium content in saturation extract and exchangeable sodium of two saline-sodic soils: one from irrigated Perimeter Engenheiro Arco Verde in the municipality of Condado and another from irrigated Perimeter of São Gonçalo, in the municipality of Sousa both in the Paraiba State Brazil, an experiment was carried out in green house of the Departamento de Solos e Engenharia Rural, Centro de Ciências Agrárias, Universidade Federal da Paraíba, Areia, Brazil, in a factorial design 2 × 5 referring the two soils and five gypsum levels equivalent to 0; 3.2; 6.3; 9.4 and 12.5 g kg-1 to each soil. The gypsum application exercised positive effects on reduction of salinity and sodicity. The values of electrical conductivity, exchangeable sodium percentage, pH and contents of soluble and exchangeable sodium in relation to data of the soils before application of treatments with gypsum in both the soils were found to decrease.

Atributos físicos e químicos do solo e desenvolvimento de laranja-pera em função de doses de cinza de bagaço de cana-de-açúcar

Pós-graduação em Agronomia (Produção Vegetal) - FCAV

Caracterização mineralógica, química e solubilização do potássio de glauconita modificada

Demand for potassium in Brazil is large and is constantly increasing, but only about 5% of all consumed potassium is produced in the country. This low domestic production implies high rate of potassium imports, leaving the country vulnerable in the event of any difficulty to import this product and currency fluctuations. The modified glauconite is a rock that has a high potential for potassium exploration, found in Minas Gerais state, its extraction is relatively cheap and the prospected rock volume is high. The difficulty for its use as a direct source of potassium is in its low solubility. Thus, the objective of this study was to perform a chemical and mineralogical characterization of the modified glauconite and evaluate the effectiveness of techniques and treatments in the potassium solubilization contained in the rock. For this study, it was used characterization techniques such as X-ray diffraction, scanning electron microscopy, diffraction by Synchrotron Light and chemical analysis of high and low power of potassium extraction. Also granulometric testing and thermal treatments with different forms of calcination were carried out. Overall, it was found that the modified glauconite is a compound of minerals, of the mica groups K-feldspar and quartz and calcination substantially alter the crystal structure of these minerals, increasing the potassium availability. While the natural solubility of glauconite modified be very low, rock calcination added with high fluxes of calcium and low magnesium content at 1200 °C led to potassium solubility increase in order of 100 times compared to that observed in the glauconite natural modified.