New bacterial cellulose nanocomposites prepared by in situ radical polymerization of methacrylate monomers

Bacterial cellulose/polymethacrylate nanocomposites have received attention in numerous areas of study and in a variety of applications. The attractive properties of methacrylate polymers and bacterial cellulose, BC, allow the synthesis of new nanocomposites with distinct characteristics. In this study, BC/poly(glycidylmethacrylate) (BC/PGMA) and BC/poly(ethyleneglycol)methacrylate (BC/PPEGMA) nanocomposites were prepared through in situ free radical polymerization of GMA and PEGMA, respectively. Ammonium persulphate (APS) was used as an initiator and N,N’methylenebisacrilamide (MBA) was used as a crosslinker in BC/PGMA. Chemical composition, morphology, thermal stability, water absorption, mechanic and surface properties were determined through specific characterization techniques. The optimal polymerization was obtained at (1:2) for BC/PGMA, (1:2:0.2) ratio for BC/GMA/MBA and (1:20) for BC/PPEGMA, with 0.5% of initiator at 60 ºC during 6 h. A maximum of 67% and 87% of incorporation percentage was obtained, respectively, for the nanocomposites BC/PGMA/MBA and BC/PPEGMA. BC/PGMA nanocomposites exhibited an increase of roughness and compactation of the three-dimensional structure, an improvement in the thermal and mechanical properties, and a decrease in their swelling ability and crystallinity. On the other hand, BC/PPEGMA showed a decrease of stiffness of three-dimensional structure, improvement in thermal and mechanical properties, an increase in their swelling ability and a decrease the crystallinity. Both BC/polymethacrylate nanocomposites exhibited a basic surface character. The acid treatment showed to be a suitable strategy to modifiy BC/PGMA nanocomposites through epoxide ring-opening reaction mechanism. Nanocomposites became more compact, smooth and with more water retention ability. A decrease in the thermal and mechanical proprieties was observed. The new nanocomposites acquired properties useful to biomedical applications or/and removal of heavy metals due to the presence of functional groups.

Influence of the base and diluent methacrylate monomers on the polymerization stress and its determinants

The aim of this study was to evaluate the effect of the association between bisphenol-A diglycidyl dimethacrylate (BisGMA) or its ethoxylated version (BisEMA) with diluents derived from the ethylene glycol dimethacrylate (EGDMA), with increasing number of ethylene glycol units (1: EGDMA, 2: DEGDMA, 3: TEGDMA, or 4: TETGDMA), or trimethylol propane trimethacrylate (TMPTMA) or 1,10-decanediol dimethacrylate (D3MA) on polymerization stress, volumetric shrinkage, degree of conversion, maximum rate of polymerization (Rpmax), and elastic modulus of experimental composites. BisGMA containing formulations presented lower shrinkage and stress but higher modulus and Rpmax than those containing BisEMA. TMPTMA presented the lowest stress among all diluents, as a result of lower conversion. EGDMA, DEGDMA, TEGDMA, and TETGDMA presented similar polymerization stress which was higher than the stress presented by D3MA and TMPTMA. D3MA presented similar conversion when copolymerized with both base monomers. The other diluents presented higher conversion when associated with BisEMA. EGDMA showed similar shrinkage compared with DEGDMA and higher than the other diluents. The lower conversion achieved by TMPTMA did not jeopardize its elastic modulus, similar to the other diluents. Despite the similar conversion presented by D3MA in comparison with EGDMA and DEGDMA, its lower elastic modulus may limit its use. Rather than proposing new materials, this study provides a systematic evaluation of off the shelf monomers and their effects on stress development, as highlighted by the analysis of conversion, shrinkage and modulus, to aid the optimization of commercially available materials. (c) 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012

Monte Carlo simulation for the modification of polymer via grafting

Monte Carlo method has been applied to investigate the kinetic of grafting reaction in free radical copolymerization. The simulation is quits in agreement with that of theoretical and experimental results. It proves that the Monte Carlo simulation is an effective method for investigating the grafting reaction of free radical copolymerization. (C) 2000 Elsevier Science Ltd. All rights reserved.

Cinnamate ester containing liquid crystalline side chain polymers

The synthesis of methacrylate esters of 4-cyanophenyl-(4-(ω-hydroxyalkyloxy)) cinnamates, with spacer lengths of 2 and 6 methylene units and the synthesis of the corresponding acrylate ester with a spacer of 2 methylene units are described. The methacrylate monomers were polymerized by free radical polymerization, both as homopolymers and as copolymers with the analogous benzoate monomer of spacer length 6. The acrylate ester could not be polymerized successfully under the same reaction conditions. Polymers were characterized by NMR spectroscopy, gel permeation chromatography, differential scanning calorimetry, and thermo-optic observations. Of the monomers prepared, only the cinnamate with a hexamethylene spacer shows a mesophase, seen on supercooling of the melt. All of the polymers prepared were liquid crystalline, with smectic behavior predominating in the polymethacrylates with the longer spacer group. A narrow nematic region is seen just below the clearing temperature with a range of 3–9°C, nematic character is increased in the copolymer series with the degree of incorporation of the cinnamate monomer with the spacer group of length 2.

Anisotrope Kolloide aus flüssigkristallinen Polymeren

In dieser Arbeit wird die Synthese, Charakterisierung und Manipulation anisotroper Kolloide aus flüssigkristallinen Polymeren beschrieben. Um Kolloide verschiedener Größe und aus verschiedenen Polymeren zu erhalten, wurden verschiedene Techniken verwendet. Einerseits wurden Kolloide aus nematischen und smektischen Polymeren mit Durchmessern meist im Bereich von 0,5 bis 3,5 Mikrometern hergestellt. Dazu wurden 16 verschiedene Acrylat- und Methacrylatmonomere synthetisiert und mittels Dispersionspolymerisation polymerisiert. Durch Variation der Polymerisationsbedingungen wurden Kolloide verschiedener Größe und Polydispersität erhalten. Durch Saatpolymerisation konnten zudem die Kugelgrößen bei gleichbleibend geringer Polydispersität erhöht werden. Polarisationsmikroskopie zeigt, dass die meisten Kolloide mit einer Größe zwischen ca. 2 bis 4 Mikrometern eine bipolare Direktorkonfiguration haben. Einige dieser Kolloide wurden mit einer optischen Pinzette mit zirkular polarisiertem Licht eingefangen und rotiert. Zum anderen wurden verschiedene flüssigkristalline Polymere (Polysiloxane, Hauptkettenpolymere und Polyacrylate) durch den Miniemulsionsprozess in Kolloide mit Durchmessern im Bereich von ca. 50 bis 300 nm überführt. Durch Variation der Emulgator- und Polymermenge sowie der Art des Emulgators konnte die Kugelgröße beeinflusst werden. Für die Polysiloxankolloide erfolgte die Aufklärung ihrer inneren Struktur mittels TEM und Kryo-TEM, da durch das Silizium im Polymerrückgrat ohne zusätzliches Anfärben ein Kontrast vorhanden ist. Die TEM-Aufnahmen zeigen deutlich die smektische Schichtstruktur innerhalb der Kolloide aus „verdünnten“ Copolysiloxanen und sind somit der erste direkte Beweis für die Mikrophasenseparation zwischen den Mesogenen und Polysiloxanketten, die bisher basierend auf Röntgenmessungen nur indirekt vorhergesagt wurde. Für die Copolysiloxane mit 2-Ring-Mesogenen wurden zwiebelartige Strukturen und für die Copolysiloxane mit 3-Ring-Mesogenen parallele Schichtstrukturen gefunden. Im ersten Fall folgt die smektische Schichtstruktur der Kugelsymmetrie des Kolloids, im zweiten Fall dominiert die Tendenz der smektischen Schichten, sich parallel anzuordnen.

Alpha, Omega end group functionalization of RAFT polymers based on pentafluorophenyl esters and methane thiosulfonates

While polymers with different functional groups along the backbone have intensively been investigated, there is still a challenge in orthogonal functionalization of the end groups. Such well-defined systems are interesting for the preparation of multiblock (co) polymers or polymer networks, for bio-conjugation or as model systems for examining the end group separation of isolated polymer chains. rnHere, Reversible Addition Fragmentation Chain Transfer (RAFT) polymerization was employed as method to investigate improved techniques for an a, w end group functionalization. RAFT produces polymers terminated in an R group and a dithioester-Z group, where R and Z stem from a suitable chain transfer agent (CTA). rnFor alpha end group functionalization, a CTA with an activated pentafluorophenyl (PFP) ester R group was designed and used for the polymerization of various methacrylate monomers, N-isopropylacrylamide and styrene yielding polymers with a PFP ester as a end group. This allowed the introduction of inert propyl amides, of light responsive diazo compounds, of the dyes NBD, Texas Red, or Oregon Green, of the hormone thyroxin and allowed the formation of multiblocks or peptide conjugates. rnFor w end group functionalization, problems of other techniques were overcome through an aminolysis of the dithioester in the presence of a functional methane thiosulfonate (MTS), yielding functional disulfides. These disulfides were stable under ambient conditions and could be cleaved on demand. Using MTS chemistry, terminal methyl disulfides (enabling self-assembly on planar gold surfaces and ligand substitution on gold and semiconductor nanoparticles), butynyl disulfide end groups (allowing the “clicking” of the polymers onto azide functionalized surfaces and the selective removal through reduction), the bio-target biotin, and the fluorescent dye Texas Red were introduced into polymers. rnThe alpha PFP amidation could be performed under mild conditions, without substantial loss of DTE. This way, a step-wise synthesis produced polymers with two functional end groups in very high yields. rnAs examples, polymers with an anchor group for both gold nanoparticles (AuNP) and CdSe / ZnS semi-conductor nanoparticles (QD) and with a fluorescent dye end group were synthesized. They allowed a NP decoration and enabled an energy transfer from QD to dye or from dye to AuNP. Water-soluble polymers were prepared with two different bio-target end groups, each capable of selectively recognizing and binding a certain protein. The immobilization of protein-polymer-protein layers on planar gold surfaces was monitored by surface plasmon resonance.Introducing two different fluorescent dye end groups enabled an energy transfer between the end groups of isolated polymer chains and created the possibility to monitor the behavior of single polymer chains during a chain collapse. rnThe versatility of the synthetic technique is very promising for applications beyond this work.

Poly(lactide): from hyperbranched copolyesters to new block copolymers with functional methacrylates

The prologue of this thesis (Chapter 1.0) gives a general overview on lactone based poly(ester) chemistry with a focus on advanced synthetic strategies for ring-opening polymerization, including the emerging field of organo catalysis. This section is followed by a presentation of the state-of the art regarding the two central fields of the thesis: (i) polyfunctional and branched poly(ester)s in Chapter 1.1 as well as (ii) the development of new poly(ester) based block copolymers with functional methacrylates (Chapter 1.2). Chapter 2 deals with the synthesis of new, non-linear poly(ester) structures. In Chapter 2.1, the synthesis of poly(lactide)-based multiarm stars, prepared via a grafting-from method, is described. The hyperbranched poly(ether)-poly(ol) poly(glycerol) is employed as a hydrophilic core molecule. The resulting star block copolymers exhibit potential as phase transfer agents and can stabilize hydrophilic dyes in a hydrophobic environment. In Chapter 2.2, this approach is expanded to poly(glycolide) multiarm star polymers. The problem of the poor solubility of linear poly(glycolide)s in common organic solvents combined with an improvement of the thermal properties has been approached by the reduction of the total chain length. In Chapter 2.3, the first successful synthesis of hyperbranched poly(lactide)s is presented. The ring-opening, multibranching copolymerization of lactide with the “inimer” 5HDON (a hydroxyl-functional lactone monomer) was carefully examined. Besides a precise molecular characterization involving the determination of the degree of branching, we were able to put forward a reaction model for the formation of branching during polymerization. Several innovative approaches to amphiphilic poly(ester)/poly(methacrylate)-based block copolymers are presented in the third part of the thesis (Chapter 3). Block copolymer build-up especially relies on the combination of ring-opening and living radical polymerization. Atom transfer radical polymerization has been successfully combined with lactide ring-opening, using a “double headed” initiator. This strategy allowed for the realization of poly(lactide)-block-poly(2-hydroxyethyl methacrylate) copolymers, which represent promising materials for tissue engineering scaffolds with anti-fouling properties (Chapter 3.1). The two-step/one-pot approach forgoes the use of protecting groups for HEMA by a careful selection of the reaction conditions. A series of potentially biocompatible and partially biodegradable homo- and block copolymers is described in Chapter 3.2. In order to create a block copolymer with a comparably strong hydrophilic character, a new acetal-protected glycerol monomethacrylate monomer (cis-1,3- benzylidene glycerol methacrylate/BGMA) was designed. The hydrophobic poly(BGMA) could be readily transformed into the hydrophilic and water-soluble poly(iso-glycerol methacrylate) (PIGMA) by mild acidic hydrolysis. Block copolymers of PIGMA and poly(lactide) exhibited interesting spherical aggregates in aqueous environment which could be significantly influenced by variation of the poly(lactide)s stereo-structure. In Chapter 3.3, pH-sensitive poly(ethylene glycol)-b-PBGMA copolymers are described. At slightly acidic pH values (pH 4/37°C), they decompose due to a polarity change of the BGMA block caused by progressing acetal cleavage. This stimuli-responsive behavior renders the system highly attractive for the targeted delivery of anti-cancer drugs. In Chapter 3.4, which was realized in cooperation, the concept of biocompatible, amphiphilic poly(lactide) based polymer drug conjugates, was pursued. This was accomplished in the form of fluorescently labeled poly(HPMA)-b-poly(lactide) copolymers. Fluorescence correlation spectroscopy (FCS) of partially biodegradable block copolymer aggregates exhibited fast cellular uptake by human cervix adenocarcinoma cells without showing toxic effects in the examined concentration range (Chapter 4.1). The current state of further projects which will be pursued in future studies is addressed in Chapter 4. This covers the synthesis of biocompatible star block copolymers (Chapter 4.2) and the development of new methacrylate monomers for biomedical applications (Chapters 4.3 and 4.4). Finally, the further investigation of hydroxyl-functional lactones and carbonates which are promising candidates for the synthesis of new hydrophilic linear or hyperbranched biopolymers, is addressed in Chapter 4.5.

Recouvrements à base de dextrane pour applications médicales

L’ingénierie des biomatériaux a connu un essor prodigieux ces dernières décennies passant de matériaux simples à des structures plus complexes, particulièrement dans le domaine cardiovasculaire. Cette évolution découle de la nécessité des biomatériaux de permettre la synergie de différentes propriétés, dépendantes de leurs fonctions, qui ne sont pas forcément toutes compatibles. Historiquement, les premiers matériaux utilisés dans la conception de dispositifs médicaux étaient ceux présentant le meilleur compromis entre les propriétés physico-chimiques, mécaniques et biologiques que nécessitait leur application. Cependant, il se peut qu’un tel dispositif possède les bonnes propriétés physico-chimiques ou mécaniques, mais que sa biocompatibilité soit insuffisante induisant ainsi des complications cliniques. Afin d’améliorer ces propriétés biologiques tout en conservant les propriétés de volume du matériau, une solution est d’en modifier la surface. L’utilisation d’un revêtement permet alors de moduler la réponse biologique à l’interface biomatériau-hôte et de diminuer les effets indésirables. Ces revêtements sont optimisés selon deux critères principaux : la réponse biologique et la réponse mécanique. Pour la réponse biologique, les deux approches principales sont de mettre au point des revêtements proactifs qui engendrent l’adhérence, la prolifération ou la migration cellulaire, ou passifs, qui, principalement, sont inertes et empêchent l’adhérence de composés biologiques. Dans certains cas, il est intéressant de pouvoir favoriser certaines cellules et d’en limiter d’autres, par exemple pour lutter contre la resténose, principalement due à la prolifération incontrôlée de cellules musculaires lisses qui conduit à une nouvelle obstruction de l’artère, suite à la pose d’un stent. La recherche sur les revêtements de stents vise, alors, à limiter la prolifération de ces cellules tout en facilitant la ré-endothélialisation, c’est-à-dire en permettant l’adhérence et la prolifération de cellules endothéliales. Dans d’autres cas, il est intéressant d’obtenir des surfaces limitant toute adhérence cellulaire, comme pour l’utilisation de cathéter. Selon leur fonction, les cathéters doivent empêcher l’adhérence cellulaire, en particulier celle des bactéries provoquant des infections, et être hémocompatibles, principalement dans le domaine vasculaire. Il a été démontré lors d’études précédentes qu’un copolymère à base de dextrane et de poly(méthacrylate de butyle) (PBMA) répondait aux problématiques liées à la resténose et qu’il possédait, de plus, une bonne élasticité, propriété mécanique importante due à la déformation que subit le stent lors de son déploiement. L’approche de ce projet était d’utiliser ce copolymère comme revêtement de stents et d’en améliorer l’adhérence à la surface en formant des liens covalents avec la surface. Pour ce faire, cela nécessitait l’activation de la partie dextrane du copolymère afin de pouvoir le greffer à la surface aminée. Il était important de vérifier pour chaque étape l’influence des modifications effectuées sur les propriétés biologiques et mécaniques des matériaux obtenus, mais aussi d’un point de vue de la chimie, l’influence que cette modification pouvait induire sur la réaction de copolymérisation. Dans un premier temps, seul le dextrane est considéré et est modifié par oxydation et carboxyméthylation puis greffé à des surfaces fluorocarbonées aminées. L’analyse physico-chimique des polymères de dextrane modifiés et de leur greffage permet de choisir une voie de modification préférentielle qui n’empêchera pas ultérieurement la copolymérisation. La carboxyméthylation permet ainsi d’obtenir un meilleur recouvrement de la surface tout en conservant la structure polysaccharidique du dextrane. Le greffage du dextrane carboxyméthylé (CMD) est ensuite optimisé selon différents degrés de modification, tenant compte aussi de l’influence que ces modifications peuvent induire sur les propriétés biologiques. Finalement, les CMD précédemment étudiés, avec des propriétés biologiques définies, sont copolymérisés avec des monomères de méthacrylate de butyle (BMA). Les copolymères ainsi obtenus ont été ensuite caractérisés par des analyses physico-chimiques, biologiques et mécaniques. Des essais préliminaires ont montrés que les films de copolymères étaient anti-adhérents vis-à-vis des cellules, ce qui a permis de trouver de nouvelles applications au projet. Les propriétés élastiques et anti-adhérentes présentées par les films de copolymères CMD-co-PBMA, les rendent particulièrement intéressants pour des applications comme revêtements de cathéters.

A thermal expulsion approach to homogeneous large-volume methacrylate monolith preparation; enabling large-scale rapid purification of biomolecules

Numerous efforts have been dedicated to the synthesis of large-volume methacrylate monoliths for large-scale biomolecules purification but most were obstructed by the enormous release of exotherms during preparation, thereby introducing structural heterogeneity in the monolith pore system. A significant radial temperature gradient develops along the monolith thickness, reaching a terminal temperature that supersedes the maximum temperature required for structurally homogenous monoliths preparation. The enormous heat build-up is perceived to encompass the heat associated with initiator decomposition and the heat released from free radical-monomer and monomer-monomer interactions. The heat resulting from the initiator decomposition was expelled along with some gaseous fumes before commencing polymerization in a gradual addition fashion. Characteristics of 80 mL monolith prepared using this technique was compared with that of a similar monolith synthesized in a bulk polymerization mode. An extra similarity in the radial temperature profiles was observed for the monolith synthesized via the heat expulsion technique. A maximum radial temperature gradient of only 4.3°C was recorded at the center and 2.1°C at the monolith peripheral for the combined heat expulsion and gradual addition technique. The comparable radial temperature distributions obtained birthed identical pore size distributions at different radial points along the monolith thickness.

Click functionalization of methacrylate-based hydrogels and their cellular response

Methacrylate-based hydrogels, such as homo- and copolymers of 2-hydroxyethyl methacrylate (HEMA), have demonstrated significant potential for use in biomedical applications. However, many of these hydrogels tend to resist cell attachment and growth at their surfaces, which can be detrimental for certain applications. In this article, glycidyl methacrylate (GMA) was copolymerized with HEMA to generate gels functionalized with epoxide groups. The epoxides were then functionalized by two sequential click reactions, namely, nucleophilic ring opening of epoxides with sodium azide and then coupling of small molecules and peptides via Huisgen's copper catalyzed 1,3-dipolar cycloaddition of azides with alkynes. Using this strategy it was possible to control the degree of functionalization by controlling the feed ratio of monomers during polymerization. In vitro cell culture of human retinal pigment epithelial cell line (ARPE-19) with the hydrogels showed improved cell adhesion, growth and proliferation for hydrogels that were functionalized with a peptide containing the RGD sequence. In addition, the cell attachment progressively decreased with increasing densities of the RGD containing peptide. In summary, a facile methodology has been presented that gives rise to hydrogels with controlled degrees of functionality, such that the cell response is directly related to the levels and nature of that functionality.

Synthesis and characterization of tetrapolymers of styrene, methyl methacrylate, alpha-methylstyrene, and oxygen

This paper presents the first report on a terpolyperoxide (TPPE) synthesized by the oxidative terpolymerization of styrene, methyl methacrylate, and a-methylstyrene. TPPEs of different compositions were synthesized by varying the vinyl monomers feed, and they were then characterized by spectroscopic and thermal studies. The conventional terpolymer equation has been used to predict the composition of TPPEs. The H-1 NMR chemical shift values of TPPEs were found to vary with the composition. The shape of the backbone methylene protons (4.00-4.50 ppm) was found to be sensitive to the sequence distribution of vinyl monomers in the polymer chain. Formaldehyde, benzaldehyde, acetophenone, and methyl pyruvate were identified as the primary degradation products. The overall thermal stability and the average enthalpy of degradation (Delta H-d), as obtained by thermogravimetric analysis and differential scanning calorimetry, respectively, do not vary much with the composition of TPPEs.

Reactivity ratios for the oxidative copolymerizations of indene with methyl methacrylate and methacrylonitrile

The copolyperoxides of indene with methyl methacrylate and methacrylonitrile have been synthesized by the free-radical-initiated oxidative copolymerization of indene and the monomers. The compositions of copolyperoxides, obtained from H-1 and C-13 NMR spectra, have been utilized to determine the reactivity ratios. The reactivity ratios indicate that the copolyperoxides contain a large proportion of the indene units in random placement. Thermal degradation studies of the copolyperoxides by differential scanning calorimetry and electron-impact mass spectroscopy support alternating peroxide units in the copolyperoxide chain. The energy of activation for thermal degradation suggests that the degradation is controlled by the dissociation of the peroxide (-O-O-) bonds in the copolyperoxide chain. The flexibility of copolyperoxide in terms of glass transition temperature (T-g) has also been examined. (C) 2002 Elsevier Science Ltd. All rights reserved.

Assembly of side-functional monomers with inorganic nanometer particles

Monomers of methacrylate with various pi -conjugated pendants were designed and prepared in our laboratory, The monomer with suitable end-group was successfully assembled with nano-scale inorganic particles to form an orderly-aligned structure that showed special optical properties, both absorption and emission band were much red-shifted compared with the monomer, A new type of organic/inorganic hybrid materials was obtained by in situ polymerization of the assembly, The hybrid materials could also show special optical properties as the assembly, This might open a new route to tune the emission color.

Reversible addition-fragmentation chain transfer mediated radical polymerization of asymmetrical divinyl monomers targeting hyperbranched vinyl polymers

Reversible addition-fragmentation chain transfer (RAFT) mediated radical polymerizations of allyl methacrylate and undecenyl methacrylate, compounds containing two types of vinyl groups with different reactivities, were investigated to provide hyperbranched polymers. The RAFT agent benzyl dithiobenzoate was demonstrated to be an appropriate chain-transfer agent to inhibit crosslinking and obtain polymers with moderate-to-high conversions. The polymerization of allyl methacrylate led to a polymer without branches but with five- or six-membered rings. However, poly(undecenyl methacrylate) showed an indication of branching rather than intramolecular cycles. The hyperbranched structure of poly(undecenyl methacrylate) was confirmed by a combination of H-1, C-13, H-1-H-1 correlation spectroscopy, and distortionless enhancement by polarization transfer 135 NMR spectra. The branching topology of the polymers was controlled by the variation of the reaction temperature, chain-transfer-agent concentration, and monomer conversion. The significantly lower inherent viscosities of the resulting polymers, compared with those of linear analogues, demonstrated their compact structure,

Polymerization of methyl methacrylate by iron(II) pyridinebisimine complexes

Fe(II) pyridinebisimine complexes activated with trialkylaluminium or modified methylaluminoxane (MMAO) as catalysts were employed for the polymerization of methyl methacrylate. Polymer yields, activities and polymer molecular weights as well as molecular weight distributions can be controlled over a wide range by the variation of the structures of the Fe(II) pyridinebisimine complexes and the reaction parameters such as Al/Fe molar ratio, monomer/catalyst molar ratio, monomer concentration, reaction temperature and time applied to the polymerization of methyl methacrylate. Under optimum condition, the catalytic activity of Fe(II) complex is of up to 74.5 kg(polym)/mol(Fe)h.