Hot deformation characteristics of a nitride strengthened martensitic heat resistant steel

Constitutive equations including an Arrhenius term have been applied to analyze the hot deformation behavior of a nitride-strengthened (NS) martensitic heat resistant steel in temperature range of 900–1200 °C and strain rate range of 0.001–10 /s. On the basis of analysis of the deformation data, the stress–strain curves up to the peak were divided into four regions, in sequence, representing four processes, namely hardening, dynamic recovery (DRV), dynamic strain induced transformation (DSIT), and dynamic recrystallization (DRX), according to the inflection points in ∂θ/∂σ∂θ/∂σ and ∂(∂θ/∂σ)/∂σ∂(∂θ/∂σ)/∂σ curves. Some of the inflection points have their own meanings. For examples, the minimum of ∂θ/∂σ∂θ/∂σ locates the start of DRV and the maximum of it indicates the start of DRX. The results also showed that the critical strain of DRX was sensitive to ln(Z) below 40, while the critical stress of DRX was sensitive to it above 40. The final microstructures under different deformation conditions were analyzed in terms of softening processes including DRV, DRX, metadynamic crystallization (MDRX) and DSIT.

Analysis of deformation behavior and workability of advanced 9Cr-Nb-V ferritic heat resistant steels

Hot compression tests were carried out on 9Cr–Nb–V heat resistant steels in the temperature range of 600–1200 °C and the strain rate range of 10−2–100 s−1 to study their deformation characteristics. The full recrystallization temperature and the carbon-free bainite phase transformation temperature were determined by the slope-change points in the curve of mean flow stress versus the inverse of temperature. The parameters of the constitutive equation for the experimental steels were calculated, including the stress exponent and the activation energy. The lower carbon content in steel would increase the fraction of precipitates by increasing the volume of dynamic strain-induced (DSIT) ferrite during deformation. The ln(εc) versus ln(Z) and the ln(σc) versus ln(Z) plots for both steels have similar trends. The efficiency of power dissipation maps with instability maps merged together show excellent workability from the strain of 0.05 to 0.6. The microstructure of the experimental steels was fully recrystallized upon deformation at low Z value owing to the dynamic recrystallization (DRX), and exhibited a necklace structure under the condition of 1050 °C/0.1 s−1 due to the suppression of the secondary flow of DRX. However, there were barely any DRX grains but elongated pancake grains under the condition of 1000 °C/1 s−1 because of the suppression of the metadynamic recrystallization (MDRX).

Microstructure evolution modeling of square-diamond pass hot bar rolling of AISI 4135 steel

In this study, kinetics of the static (SRX) and metadynamic recrystallization (MDRX) of AISI4135 steel was investigated using hot torsion tests. Continuous torsion tests were carried out to determine the critical strain for dynamic recrystallization (DRX). The times for 50% recrystallization of SRX and MDRX were determined, respectively, by means of interrupted torsion tests. Furthermore, austenite grain size (AGS) evolution due to recrystallization (RX) was measured by optical microscopy. With the help of the evolution model established, the AGS for hot bar rolling of AISI4135 steel was predicted numerically. The predicted AGS values were compared with the results using the other model available in the literature and experimental results to verify its validity. Then, numerical predictions depending on various process parameters such as interpass time, temperature, and roll speed were made to investigate the effect of these parameters on AGS distributions for square-diamond pass rolling. Such numerical results were found to be beneficial in understanding the effect of processing conditions on the microstructure evolution better and control the rolling processes more accurately.

Microstructural characterization of the austenite behaviour during metadynamic recrystallization

The work discusses the recent findings obtained from the microstructural characterization of an austenitic Ni-30%Fe model alloy during metadynamic recrystallization (MDRX) using both EBSD and TEM techniques. The characterization of the grain structure, texture and dislocation substructure evolution of the fully dynamically recrystallized (DRX) microstructure during post deformation annealing revealed a novel softening mechanism occurring under the current experimental conditions. It is proposed that the initial softening stage involves rapid growth of the dynamically formed nuclei and migration of the mobile boundaries in correspondence with the well-established MDRX mechanism. However, the sub-boundaries within DRX grains progressively disintegrate through dislocation climb and dislocation annihilation, which ultimately leads to the formation of dislocation-free grains. Consequently, the DRX texture largely remains preserved throughout the annealing process.

Microstructure evolution and softening processes occurring during annealing of hot deformed Ni-30Fe austenite

The current work investigates the microstructure evolution and softening processes that take place during annealing of an austenitic Ni-30Fe model alloy subjected to hot deformation in the dynamic recrystallization (DRX) regime. The substructure of the deformed matrix grains largely comprised organized microband arrays, though that of the DRX grains consisted of more random, complex subgrain/cell arrangements. This substructure disparity was also reflected by the distinct difference in the mechanism of post-deformation softening taking place during annealing of the deformed matrix and DRX grains. In the former, the recrystallization process took place through nucleation and growth of new grains fully replacing the deformed structure, as expected for the classical static recrystallization (SRX). The corresponding texture was essentially random, in contrast to that of the DRX grains dominated by low Taylor factor components. The microbands originally present within the deformed matrix grains displayed some tendency to disintegrate during annealing, nonetheless, they remained largely preserved even at prolonged holding times. During annealing of the fully DRX microstructure, a novel softening mechanism was revealed. The initial post-dynamic softening stage involved rapid growth of the dynamically formed nuclei and migration of the mobile boundaries in correspondence with the well-established metadynamic recrystallization (MDRX) mechanism. However, in contrast to the deformed matrix, SRX was not observed and the sub-boundaries within DRX grains rapidly disintegrated through dislocation climb and dislocation annihilation, which led to the formation of dislocation-free grains already at short holding times. Consequently, the DRX texture initially became slightly weakened and then remained largely preserved throughout the annealing process.

Texture evolution and softening processes in an austenitic Ni-30Fe alloy subjected to hot deformation and subsequent annealing

The current work has investigated the texture development in an austenitic Ni-30Fe model alloy during deformation within the dynamic recrystallization (DRX) regime and after post-deformation annealing. Both the deformed matrix and DRX texture displayed the expected FCC shear components, the latter being dominated by the low Taylor factor grains, which was presumably caused by their lower consumption rate during DRX. The deformed matrix grains were largely characterized by organized, microband structures, while the DRX grains showed more random, complex subgrains/cell arrangements. The latter substructure type proved to be significantly less stable during post-deformation annealing. The recrystallization of the deformed matrix occurred through nucleation and growth of new grains fully replacing the deformed structure, as expected for the classical static recrystallization (SRX). Unlike the DRX grains, the SRX texture was essentially random. By contrast, a novel softening mechanism was revealed during annealing of the fully DRX microstructure. The initial post-dynamic softening stage involved rapid growth of the dynamically formed nuclei and migration of the mobile boundaries in line with the well-established metadynamic recrystallization (MDRX) mechanism, which weakened the starting DRX texture. However, in parallel, the sub-boundaries within the deformed DRX grains progressively disintegrated through dislocation climb and dislocation annihilation, which ultimately led to the formation of dislocation-free grains. Consequently, the weakened DRX texture largely remained preserved throughout the annealing process.