Linear polyethylene and polypropylene: problems and opportunities. A report for businessmen,

Mode of access: Internet.

Influence of molecular composition on the development of microstructure from sheared polyethylene melts: Molecular and lamellar templating

A combination of in situ and ex situ X-ray scattering techniques and transmission electron microscopy has been used to study the crystallization behaviour of polyethylene, following the imposition of melt shear. In the case of a branched material, the imposition of shear flow up to a rate of 30 s(-1) was found to induce no anisotropy. Although shearing the linear material only ever induced a very small degree of anisotropy in the melt, for shear rates > 0.15 s(-1), subsequent crystallization resulted in increasing anisotropy. Blends of the above two polyethylenes were produced, in which the linear material constituted the minority fraction (similar to 10%). Isothermal crystallization at temperatures where extensive crystallization of the branched material does not occur demonstrated that the behaviour of the linear component of the sheared blend mirrored that of the linear polyethylene alone. However, in addition, it was found that when crystallized in the presence of an oriented morphology, the branched polymer also formed anisotropic structures. We have termed the process templating, in which the crystallization behaviour of the bulk of the system (similar to 90% branched material) is completely altered (spherulitic to oriented lamellar) by mapping it onto a pre-existing minority structure (similar to 10% linear polymer). (c) 2006 Elsevier Ltd. All rights reserved.

Linear nucleation of polymers

The use of high-melting fibres as linear nuclei for quiescent polymeric melts is instrumental in providing the superior mechanical properties of polymeric self-composites. It also has inherent advantages in the elucidation of fundamental aspects of polymeric crystallization and self-organization, not least in allowing systematic microscopic studies of polymeric crystallization from nucleation through to the growth interface. This has demonstrated explicitly that lamellae develop in two distinct ways, for slower and faster growth, depending on whether fold packing has or has not time to order before the next molecular layer is added with only the former leading to banded growth in linear polyethylene. Other gains in understanding concern cellulation and morphological instability, internuclear interference, isothermal lamellar thickening and banded growth being a consequence of the partial relief of initial surface stress. (c) 2006 Elsevier Ltd. All rights reserved.

The development of organized structures in polyethylene crystallized from a sheared melt, analyzed by WAXS and TEM

The development of global orientation and morphological features in linear polyethylene crystallizing from a sheared melt are studied using in-situ time-resolving wide angle X-ray scattering (WAXS) and ex-situ transmission electron microscopy. It is found that samples subjected to a shear rate above a critical value of ~1s-1 result in macroscopically oriented structures in the crystallized sample. This critical shear rate appears to be independent of the differences in molecular weight distribution of the samples studied although the morphologies which develop are sensitive to quite small differences in molecular weight distributions. The presence of shish kebabs in the morphology is shown to differ markedly according to variations in the upper molecular weight fraction of the molecular weight distribution, even though the resulting global orientation does not. The WAXS also reveals that areas which evidence no row nucleated structures still realize high degrees of molecular orientation. It is proposed that the formation of shish kebab or lamellar morphologies in these samples is dependent on the critical density of contiguous elongated crystallization nuclei rather than any specific global criteria.

A study of the radiation degradation of styrene/alkane and α-methylstyrene/alkane copolymers

The effects of copolymer composition and microstructure on the radiation chemistry of styrene/alkane and alpha-methylstyrene/alkane copolymers have been studied. The primary radical species formed on radiolysis of the copolymers at 77 K, and identified by ESR spectroscopy, are the same as those formed during radiolysis of the homopolymers. The yields of radicals for the copolymer are as predicted assuming that the cross-section is proportional to the electron density of each component; however, there is some evidence of radical migration to aromatic groups at 77 K. Changes in molecular structure on irradiation were detected by using C-13 NMR spectroscopy. Evidence of the consumption of terminal double bonds, and chain scission in alpha-methylstyrene/alkane copolymers was found. Measurements of viscosity supported the mechanism of cross-linking predominating in styrene/alkane copolymers, while in alpha-methylstyrene/alkane copolymers chain scission was the major result of irradiation. (C) 2003 Society of Chemical Industry.

Influence of monomeric and polymeric structure on the physical properties of thermoplastic polyesters derived from hydroxy fatty acids

The physical properties of three vegetable oil derived medium and long chain poly(-hydroxy fatty ester)s (P(Me--OHFA)s), namely poly(-hydroxynonanoate) [P(Me--OHC9)], poly(-hydroxytridecanoate) [P(Me--OHC13)] and poly(-hydroxyoctadecanoate) [P(Me--OHC18)] (n = 8, 12 and 17, respectively), of the [-(CH2)(n)-COO-](x) polyester homologous series are presented. The effect of M-n (M-n 10-40 kg mol(-1)) and n on the crystal structure and thermal and mechanical properties of the P(Me--OHFA)s were investigated by wide-angle X-ray diffraction (WAXD), TGA, DSC, dynamic mechanical analysis (DMA) and tensile analysis and are discussed in the context of the [-(CH2)(n)-COO-](x) polyester homologous series, contrasted with linear polyethylene (PE). For all P(Me--OHFA)s the WAXD data indicated an orthorhombic crystal phase reminiscent of linear PE with crystallinity (X-c = 50%-80%) depending strongly on M-n. The glass transition temperature and Young's modulus for P(Me--OHFA)s increased with X-c. The DSC, DMA and TGA studies for P(Me--OHFA)s (n = 8, 12 and 17) indicated strong correlations between the melting, glass transition and thermal degradation behavior and n. The established predictive structure relationships can be used for the custom engineering of polyester materials suitable for specialty and commodity applications. (c) 2014 Society of Chemical Industry

Optimised polyolefin branch quantification by 13 C NMR spectroscopy

Quantitative branch determination in polyolefins by solid- and melt-state 13C NMR has been investigated. Both methods were optimised toward sensitivity per unit time. While solid-state NMR was shown to give quick albeit only qualitative results, melt-state NMR allowed highly time efficient accurate branch quantification. Comparison of spectra obtained using spectrometers operating at 300, 500 and 700 MHz 1H Larmor frequency, with 4 and 7~mm MAS probeheads, showed that the best sensitivity was achieved at 500 MHz using a 7 mm 13C-1H optimised high temperature probehead. For materials available in large quantities, static melt-state NMR, using large diameter detection coils and high coil filling at 300 MHz, was shown to produce comparable results to melt-state MAS measurements in less time. While the use of J-coupling mediated polarisation transfer techniques was shown to be possible, direct polarisation via single-pulse excitation proved to be more suitable for branch quantification in the melt-state. Artificial line broadening, introduced by FID truncation, was able to be reduced by the use of π pulse-train heteronuclear dipolar decoupling. This decoupling method, when combined with an extended duty-cycle, allowed for significant improvement in resolution. Standard setup, processing and analysis techniques were developed to minimise systematic errors contributing to the measured branch contents. The final optimised melt-state MAS NMR method was shown to allow time efficient quantification of comonomer content and distribution in both polyethylene- and polypropylene-co-α-olefins. The sensitivity of the technique was demonstrated by quantifying branch concentrations of 8 branches per 100,000 CH2 for an industrial ‘linear’ polyethylene in only 13 hours. Even lower degrees of 3–8 long-chain branches per 100,000 carbons were able to be estimated in just 24 hours for a series of γ-irradiated polypropylene homopolymers.

18 F-Click-Radiomarkierung polymerer Trägersysteme zur ex vivo- und in vivo-Evaluierung

Die Positronen-Emissions-Tomographie (PET) ist ein leistungsstarkes, nicht-invasives, bildgebendes Verfahren in der Nuklearmedizin und hat darüber hinaus zunehmende Bedeutung in der Arzneistoffentwicklung. Zur Verbesserung des therapeutischen Index von niedermolekularen Pharmaka werden vermehrt Wirkstofftransportsysteme eingesetzt. Eine Klasse dieser Wirkstofftransportsysteme sind Liposomen. Die Weiterentwicklung der klassischen Liposomen sind sogenannte „Stealth“-Liposomen, die eine Polyethylenglykol (PEG)-Korona zur Herabsetzung der Erkennung und Ausscheidung tragen. Zur (Weiter-)Entwicklung und deren in vivo-Evaluierung bietet die PET die Möglichkeit, die Auswirkungen von strukturellen Anpassungen auf die pharmakokinetischen Eigenschaften solcher Transportsysteme zu untersuchen. Zur Evaluierung neuartiger, cholesterolverankerter, linear-hyperverzweigter Polyglycerole (Ch-PEG-hbPG) als sterisch stabilisierende Polymere in Liposomen wurden diese im Rahmen dieser Arbeit mit der prosthetischen Gruppe 18F-TEG-N3 über kupferkatalysierte Alkin-Azid Cycloaddition (CuAAC) in sehr hohen Ausbeuten radiomarkiert. Zum systematischen Vergleich des in vivo-Verhaltens wurde ebenfalls ein cholesterolbasiertes lineares PEG (Ch-PEG) mit CuAAC nahezu quantitativ radiomarkiert. Als drittes Element wurde die Direktmarkierung von Cholesterol mit [18F]F- entwickelt. Diese drei Verbindungen wurden zuerst separat als Einzelkomponenten und anschließend, in Liposomen formuliert, in Tierstudien an Mäusen hinsichtlich ihrer initialen Pharmakokinetik und Biodistribution untersucht. Dabei zeigte sich ein ähnliches Verhalten der neuartigen Ch-PEG-hbPG-Derivate zu den bekannten Ch-PEG, mit dem Vorteil der Multifunktionalität an den hyperverzweigten Strukturen. Die liposomalen Strukturen mit der neuartigen sterischen Stabilisierung wiesen eine erhöhte Blutzirkulationszeit und vorteilhafte Blut-zu-Leber- und Blut-zu-Lunge-Verhältnisse im Vergleich zu den linear stabilisierten Analoga auf.rnEine weitere Klasse von Wirkstofftransportsystemen sind polymere Trägersysteme wie pHPMA. Alkinfunktionalisierte Polymere konnten in zwei verschiedenen Größen (~12 und 60 kDa) mittels CuAAC in sehr hohen Ausbeuten mit der prosthetischen Gruppe 18F-TEG-N3 radiomarkiert werden. Bicyclononinderivate der gleichen Größen konnten ohne Kupferkatalyse über ringspannungsvermittelte Alkin-Azid-Cycloaddition (SPAAC) mikrowellengestützt markiert werden und stehen somit zur in vivo-Untersuchung hinsichtlich des Einflusses der Markierungsart zur Verfügung.

Studies on Thermoplastic Elastomer Based on Linear Low-Density Polyethylene and Latex Product Waste Modified with Thiocarbanilide

Latex waste like glove waste was effectively modified using a new reclaiming agent, thiocarbanilide. This modified waste was blended with linear low-density polyethylene (LLDPE) to develop a novel thermoplastic elastomer. Both uncrosslinked and dynamically crosslinked blends were prepared and their properties were studied. The results were found to be comparable to those of conventional thermoplastic elastomers.

Chemical Modification of Blends of Poly (Vinyl Chloride) With Linear Low Density Polyethylene

The effects of modifying blends of poly(vinyl chloride) (PVC) with linear low density polyethylene (LLDPE) by means of acrylic acid, maleic anhydride, phenolic resins and p-phenylene diamine were investigated. Modification by acrylic acid and maleic anhydride in the presence of dicumyl peroxide was found to be the most useful procedure for improving the mechanical behaviour and adhesion properties of the blend. The improvement was found to be due mainly to the grafting of the carboxylic acid to the polymer chains; grafting was found to be more effective in LLDPE/PVC blends than in pure LLDPE.

Linear Low Density Polyethylene-Biodegradability Using Bacteria from Marine Benthic Environment and Photodegradability Using Ultraviolet Light

Various compositions of linear low density polyethylene(LLDPE) containing bio-filler(either starch or dextrin)of various particle sizes were prepared.The mechanical,thermal,FTIR,morphological(SEM),water absorption and melt flow(MFI) studies were carried out.Biodegradability of the compositions were determined using a shake culture flask containing amylase producing bacteria(vibrios),which were isolated from marine benthic environment and by soil burial test. The effect of low quantities of metal oxides and metal stearate as pro-oxidants in LLDPE and in the LLDPE-biofiller compositions was established by exposing the samples to ultraviolet light.The combination of bio-filler and a pro-oxidant improves the degradation of linear low density polyethylene.The maleation of LLDPE improves the compatibility of the c blend components and thepro-oxidants enhance the photodegradability of the compatibilised blends.The responsibility studies on the partially biodegradable LLDPE containing bio-fillers and pro-oxidants suggest that the blends could be repeatedly reprocessed without deterioration in mechanical properties.

Modification of Linear Low Density Polyethylene for Improved Photo and Biodegradation

LLDPE was blended with poly (vinyl alcohol) and mechanical, thermal, spectroscopic properties and biodegradability were investigated. The biodegradability of LLDPE/PVA blends has been studied in two environments, viz. (1) a culture medium containing Vibrio sp. and (2) a soil environment over a period of 15 weeks. Nanoanatase having photo catalytic activity was synthesized by hydrothermal method using titanium-iso-propoxide. The synthesized TiO2 was characterized by X-Ray diffraction (XRD), BET studies, FTIR studies and scanning electron microscopy (SEM). The crystallite size of titania was calculated to be ≈ 6nm from the XRD results and the surface area was found to be about 310m2/g by BET method. SEM shows that nanoanatase particles prepared by this method are spherical in shape. Linear low density polyethylene films containing polyvinyl alcohol and a pro-oxidant (TiO2 or cobalt stearate with or without vegetable oil) were prepared. The films were then subjected to natural weathering and UV exposure followed by biodegradation in culture medium as well as in soil environment. The degradation was monitored by mechanical property measurements, thermal studies, rate of weight loss, FTIR and SEM studies. Higher weight loss, texture change and greater increments in carbonyl index values were observed in samples containing cobalt stearate and vegetable oil. The present study demonstrates that the combination of LLDPE/PVA blends with (I) nanoanatase/vegetable oil and (ii) cobalt stearate/vegetable oil leads to extensive photodegradation. These samples show substantial degradation when subsequent exposure to Vibrio sp. is made. Thus a combined photodegradation and biodegradation process is a promising step towards obtaining a biodegradable grade of LLDPE.

Characterization of Linear Low-Density Polyethylene/ Poly(vinyl alcohol) Blends and Their Biodegradability by Vibrio sp. Isolated from Marine Benthic Environment

Increasing amounts of plastic waste in the environment have become a problem of gigantic proportions. The case of linear low-density polyethylene (LLDPE) is especially significant as it is widely used for packaging and other applications. This synthetic polymer is normally not biodegradable until it is degraded into low molecular mass fragments that can be assimilated by microorganisms. Blends of nonbiodegradable polymers and biodegradable commercial polymers such as poly (vinyl alcohol) (PVA) can facilitate a reduction in the volume of plastic waste when they undergo partial degradation. Further, the remaining fragments stand a greater chance of undergoing biodegradation in a much shorter span of time. In this investigation, LLDPE was blended with different proportions of PVA (5–30%) in a torque rheometer. Mechanical, thermal, and biodegradation studies were carried out on the blends. The biodegradability of LLDPE/PVA blends has been studied in two environments: (1) in a culture medium containing Vibrio sp. and (2) soil environment, both over a period of 15 weeks. Blends exposed to culture medium degraded more than that exposed to soil environment. Changes in various properties of LLDPE/PVA blends before and after degradation were monitored using Fourier transform infrared spectroscopy, a differential scanning calorimeter (DSC) for crystallinity, and scanning electron microscope (SEM) for surface morphology among other things. Percentage crystallinity decreased as the PVA content increased and biodegradation resulted in an increase of crystallinity in LLDPE/PVA blends. The results prove that partial biodegradation of the blends has occurred holding promise for an eventual biodegradable product

Linear low density polyethylene (LLDPE) from ethylene using Tp(Ms)NiCl (Tp(Ms) = hydridotris(3-mesitylpyrazol-1-yl)) and CP2ZrCl2 as a tandem catalyst system

Linear low density polyethylene (LLDPE) with different branching contents were prepared from ethylene, without the addition of alpha-olefin comonomer, using a combination of catalyst precursors {Tp(Ms)}NiCl (1) (Tp(Ms) = hydridotris(3-mesitylpyrazol-1-yl)) and Cp2ZrCl2 (2) activated with MAO/TMA (1:1) in toluene at 0degreesC and by varying the nickel loading mole fraction (x(Ni)). The polymerization results showed that the turnover frequencies are strongly dependent on the x(Ni) varying from 6.6 x 10(3) to 32.1 x 10(3) mol[C2H4]/mol[Zr] h. The C-13 NMR spectra of the copolymers showed that the branch contents of the polymers increase as the x(Ni) increase in the medium promoting the production of polymers with a wide range of melting point (T-m) (C) 2004 Elsevier B.V. All rights reserved.

Linear low-density polyethylene colored with a nanoclay-based pigment: Morphology and mechanical, thermal, and colorimetric properties

In this study, a novel kind of hybrid pigment based on nanoclays and dyes was synthesized and characterized. These nanoclay-based pigments (NCPs) were prepared at the laboratory with sodium montmorillonite nanoclay (NC) and methylene blue (MB). The cation-exchange capacity of NC exchanged with MB was varied to obtain a wide color gamut. The synthesized nanopigments were thoroughly characterized. The NCPs were melt-mixed with linear low-density polyethylene (PE) with an internal mixer. Furthermore, samples with conventional colorants were prepared in the same way. Then, the properties (mechanical, thermal, and colorimetric) of the mixtures were assessed. The PE–NCP samples developed better color properties than those containing conventional colorants and used as references, and their other properties were maintained or improved, even at lower contents of dye compared to that with the conventional colorants.