Otimização dos parâmetros de processamento em Laser Melting

Dissertação de mestrado integrado em Engenharia Mecânica

Surface quality of profile extrusion dies manufactured by Selective Laser Melting

The design of plastics profile extrusion dies becomes increasingly more complex so that conventional manufacture processes reach their limit in the die manufacture. A feasible manufacture of arbitrarily designed dies is only possible by additive manufacturing. An especially promising process is hereby the Selective Laser Melting with which metal parts with series identical mechanical properties can be produced without the need for part specific tooling or downstream sintering processes. Disadvantegeous is, however, the relatively rough surface of additively manufactured parts. Against this background, the manufacturing of an profile extrusion die by Selective Laser Melting and the plastics profile surface quality, that can be achieved with such dies, is investigated. For this purpose, profiles are extruded both with an additively manufactured die and a conventionally milled sample of the same die geometry. In case of the additively manufactured die a concept for the surface finishing of the flow channel is required, which can be applied to arbitrarily shaped geometries. Therefore, two different reworking processes are applied only to the die land of the flow channel. The comparison of the surface roughnesses shows that the additively manufactured die with a polished die land delivers the same surface quality as the conventional die.

Double ion implantation and pulsed laser melting processes for third generation solar cells

In the framework of the third generation of photovoltaic devices, the intermediate band solar cell is one of the possible candidates to reach higher efficiencies with a lower processing cost. In this work, we introduce a novel processing method based on a double ion implantation and, subsequently, a pulsed laser melting (PLM) process to obtain thicker layers of Ti supersaturated Si. We perform ab initio theoretical calculations of Si impurified with Ti showing that Ti in Si is a good candidate to theoretically form an intermediate band material in the Ti supersaturated Si. From time-of-flight secondary ion mass spectroscopy measurements, we confirm that we have obtained a Ti implanted and PLM thicker layer of 135 nm. Transmission electron microscopy reveals a single crystalline structure whilst the electrical characterization confirms the transport properties of an intermediate band material/Si substrate junction. High subbandgap absorption has been measured, obtaining an approximate value of 104 cm−1 in the photons energy range from 1.1 to 0.6 eV.

Selective Laser Melting of the Eutectic Silver-Copper Alloy Ag 28 wt % Cu

The aim of this work was to perform a detailed investigation of the use of Selective Laser Melting (SLM) technology to process eutectic silver-copper alloy Ag 28 wt. % Cu (also called AgCu28). The processing occurred with a Realizer SLM 50 desktop machine. The powder analysis (SEM-topography, EDX, particle distribution) was reported as well as the absorption rates for the near-infrared (NIR) spectrum. Microscope imaging showed the surface topography of the manufactured parts. Furthermore, microsections were conducted for the analysis of porosity. The Design of Experiments approach used the response surface method in order to model the statistical relationship between laser power, spot distance and pulse time.

Caratterizzazione microstrutturale e frattografica di componenti in acciaio 316L prodotti tramite Selective Laser Melting

Il Selective Laser Melting è un processo di additive manufacturing che consiste nella realizzazione di componenti metallici tridimensionali, sovrapponendo strati di polvere, che viene via via fusa mediante una sorgente controllata di energia (laser). È una tecnica produttiva che viene utilizzata da più di 20 anni ma solo ora sta assumendo un ruolo rilevante nell’industria. È un processo versatile ma complesso che ad oggi permette di processare solo un numero limitato di leghe. Il presente lavoro di tesi riguarda in particolare lo studio, dal punto di vista microstrutturale, di componenti in acciaio inossidabile austenitico AISI-316L processato mediante Selective Laser Melting, attività svolta in collaborazione con il Gruppo di Tecnologia – Laser del Dipartimento di Ingegneria Industriale. Alla base dell’attività sperimentale è stata svolta anche un’ampia ricerca bibliografica per chiarire lo stato dell’arte sul processo e sulla lega in questione, la microstruttura, i difetti, le proprietà meccaniche e l’effetto dei parametri di processo sul componente finito. Le attività sperimentali hanno previsto una prima fase di caratterizzazione delle polveri di 316L, successivamente la caratterizzazione dei campioni prodotti tramite selective laser melting, in termini di microstruttura e difetti correlati al processo. Le analisi hanno rivelato la presenza di una microstruttura “gerarchica” costituita da melt pool, grani e celle submicrometriche. I difetti rinvenuti sono pori, delaminazione degli strati, particelle di polvere non fuse. Infine è stata eseguita la caratterizzazione frattografica dei campioni sottoposti a prove di trazione e di fatica a flessione rotante (attività condotte dal gruppo Laser) per identificare la morfologia di frattura e i siti di innesco della cricca di fatica.

Atomistic-continuum modeling of ultrafast laser-induced melting of silicon targets

In this work, we present an atomistic-continuum model for simulations of ultrafast laser-induced melting processes in semiconductors on the example of silicon. The kinetics of transient non-equilibrium phase transition mechanisms is addressed with MD method on the atomic level, whereas the laser light absorption, strong generated electron-phonon nonequilibrium, fast heat conduction, and photo-excited free carrier diffusion are accounted for with a continuum TTM-like model (called nTTM). First, we independently consider the applications of nTTM and MD for the description of silicon, and then construct the combined MD-nTTM model. Its development and thorough testing is followed by a comprehensive computational study of fast nonequilibrium processes induced in silicon by an ultrashort laser irradiation. The new model allowed to investigate the effect of laser-induced pressure and temperature of the lattice on the melting kinetics. Two competing melting mechanisms, heterogeneous and homogeneous, were identified in our big-scale simulations. Apart from the classical heterogeneous melting mechanism, the nucleation of the liquid phase homogeneously inside the material significantly contributes to the melting process. The simulations showed, that due to the open diamond structure of the crystal, the laser-generated internal compressive stresses reduce the crystal stability against the homogeneous melting. Consequently, the latter can take a massive character within several picoseconds upon the laser heating. Due to the large negative volume of melting of silicon, the material contracts upon the phase transition, relaxes the compressive stresses, and the subsequent melting proceeds heterogeneously until the excess of thermal energy is consumed. A series of simulations for a range of absorbed fluences allowed us to find the threshold fluence value at which homogeneous liquid nucleation starts contributing to the classical heterogeneous propagation of the solid-liquid interface. A series of simulations for a range of the material thicknesses showed that the sample width we chosen in our simulations (800 nm) corresponds to a thick sample. Additionally, in order to support the main conclusions, the results were verified for a different interatomic potential. Possible improvements of the model to account for nonthermal effects are discussed and certain restrictions on the suitable interatomic potentials are found. As a first step towards the inclusion of these effects into MD-nTTM, we performed nanometer-scale MD simulations with a new interatomic potential, designed to reproduce ab initio calculations at the laser-induced electronic temperature of 18946 K. The simulations demonstrated that, similarly to thermal melting, nonthermal phase transition occurs through nucleation. A series of simulations showed that higher (lower) initial pressure reinforces (hinders) the creation and the growth of nonthermal liquid nuclei. For the example of Si, the laser melting kinetics of semiconductors was found to be noticeably different from that of metals with a face-centered cubic crystal structure. The results of this study, therefore, have important implications for interpretation of experimental data on the kinetics of melting process of semiconductors.

Influence of laser surface texturing on surface microstructure and mechanical properties of adhesive joined steel sheets

This work discusses the resultant microstructure of laser surface treated galvanised steel and the mechanical properties of adhesively bonded surfaces therein. The surface microstructure obtained at laser intensities between 170 and 1700 MW cm 22 exhibit zinc melting and cavity formation. The wavy surface morphology of the treated surface exhibits an average roughness Ra between 1.0 and 1.5 mu m, and a mean roughness depth R(z) of 8.6 mu m. Atomic force microscopic analyses revealed that the R(z) inside the laser shot cavities increased from 68 to 243 nm when the incident laser intensity was increased from 170 to 1700 MW cm(-2). X-ray fluorescence analyses were used to measure Zn coating thicknesses as a function of process parameters. Both X-ray fluorescence and X-ray diffraction analyses demonstrated that the protective coating remains at the material surface, and the steel structure beneath was not affected by the laser treatment. Tensile tests under peel strength conditions demonstrated that the laser treated adhesively joined samples had resistance strength up to 88 MPa, compared to a maximum of only 23 MPa for the untreated surfaces. The maximum deformation for rupture was also greatly increased from 0.07%, for the original surface, to 0.90% for the laser treated surfaces.

Welding of additively manufactured stainless steel parts: Comparative study between sheet metal and selective laser melted parts

Additive manufacturing is a fast growing manufacturing technology capable of producing complex objects without the need for conventional manufacturing process planning. During the process the work piece is built by adding material one layer at a time according to a digital 3D CAD model. At first additive manufacturing was mainly used to make prototypes but the development of the technology has made it possible to also make final products. Welding is the most common joining method for metallic materials. As the maximum part size of additive manufacturing is often limited, it may sometimes be required to join two or more additively manufactured parts together. However there has been almost no research on the welding of additively manufactured parts so far, which means that there has been very little information available on the possible differences compared to the welding of sheet metal parts. The aim of this study was to compare the weld joint properties of additively manufactured parts to those of sheet metal parts. The welding process that was used was TIG welding and the test material was 316L austenitic stainless steel. Weld joint properties were studied by making tensile, bend and hardness tests and by studying the weld microstructures with a microscope. Results show that there are certain characteristics in the welds of additively manufactured parts. The building direction of the test pieces has some impact on the mechanical properties of the weld. Nevertheless all the welds exhibited higher yield strength than the sheet metal welds but at the same time elongation at break was lower. It was concluded that TIG welding is a feasible process for welding additively manufactured parts.

Effects of copper vapor laser radiation on the root canal wall of human teeth: A scanning electron microscope study

Objective: The aim of this study is to analyze the effects of copper vapor laser radiation on the radicular wall of human teeth. Materials and Methods: Immediately after the crowns of 10 human uniradicular teeth were cut along the cement-enamel junction, a chemical-surgical preparation of the radicular canals was completed. Then the roots were longitudinally sectioned to allow for irradiation of the surfaces of the dentin walls of the root canals. The hemi-roots were separated into two groups: one (control) with five hemi-roots that were not irradiated, and another (experimental) with 15 hemi-roots divided into three subgroups that were submitted to the following exposure times: 0.02,0.05, and 0.1 s. A copper vapor laser (510.6 nm) with a total average power of 6.5 W in green emission, frequency of 16.000 Hz, and pulse duration of 30 ns was used. Results: The results obtained by scanning electron microscope analysis showed the appearance of a cavity in the region of laser beam impact, with melting, recrystallization, and cracking on the edges of the dentin of the cavity due to heat diffusion. Conclusions: We determined that the copper vapor laser produces significant morphologic changes in the radicular wall of human teeth when using the parameters in this study. However, further research should be done to establish parameters that are compatible with dental structure in order to eliminate thermal damages. © Mary Ann Liebert, Inc.

Effetto della sabbiatura sul comportamento a fatica della lega AlSi10Mg prodotta con Laser Powder Bed Fusion e trattata termicamente

La tesi in oggetto ha lo scopo di determinare l’effetto della sabbiatura sul comportamento a fatica della lega AlSi10Mg prodotta mediante Laser Powder Bed Fusion e trattata termicamente. I parametri di processo e di trattamento termico (T5 e T6) sono stati precedentemente ottimizzati. Al fine di determinare l’effetto della sabbiatura su topografia superficiale e microstruttura dei campioni, si sono condotte molteplici analisi avvalendosi di strumenti quali profilometria, microscopia ottica ed in scansione, analisi di tensioni residue con diffrazione a raggi X e prove di durezza. Attraverso prove di fatica per flessione rotante, eseguite secondo il metodo Stair-Case per la determinazione della resistenza a fatica, e successiva caratterizzazione delle superfici di frattura si vuole correlare il difetto killer, ossia quello responsabile del cedimento per fatica, alle caratteristiche morfologiche e microstrutturali. Il difetto killer viene caratterizzato in termini di dimensione e distanza dalla superficie e per mostrare la relazione fra la dimensione del difetto killer e la resistenza a fatica si adotta il diagramma di Kitagawa-Takahashi con modellazione di Murakami ed EL Haddad. Si è evidenziato che tutti i difetti killer sono riconducibili a lack-of-fusion con dimensione superiore ai 100 μm ad una profondità compresa fra i 150 e i 200 μm, indipendentemente dal trattamento termico o meccanico applicato. In termini di fatica si osserva che il trattamento T6 conferisce al materiale migliori proprietà rispetto a quello T5. Il processo di sabbiatura, confrontato con quello di lucidatura superficiale, ha portato a miglioramenti in termini di durezza e tensioni residue di compressione, ma si è rivelato quasi ininfluente sulla resistenza a fatica. Sulla base di quanto sopra, si conferma la possibilità di applicazione della sabbiatura in ambito industriale a componenti meccanici, anche in sostituzione della lucidatura, ottenendo un beneficio anche economico.

Metal additive manufacturing of internal flow channels with powder bed fusion processes

This thesis studies the advantages, disadvantages and possibilities of additive manufacturing in making components with internal flow channels. These include hydraulic components, components with cooling channels and heat exchangers. Processes studied in this work are selective laser sintering and selective laser melting of metallic materials. The basic principles of processes and parameters involved in the process are presented and different possibilities of internal channel manufacturing and flow improvement are introduced

Rapid Manufacturing - auch mit SLM

Rapid Manufacturing (RM) wurde als Schlagwort in der letzten Zeit insbesondere aus dem Bereich des Selective Laser Sintering (SLS) bekannt. In dieser inzwischen über 15-jährigen Technologieentwicklung wurden in den vergangenen Jahren bedeutende Fortschritte erzielt, die die Bauteileigenschaften nahe an die Anforderungen für End-Teile heran brachten. So ist das RM denn auch weniger aus der Sicht grösserer Losgrösse zu verstehen. Viel mehr bedeutet Rapid Manufacturing, dass die Bauteile nach einer generativen Fertigung direkt im Endprodukt resp. der Endanwendung zum Einsatz kommt. Das Selective Laser Melting, mit welchem aus metallischen Pulvermaterialien direkt Metallteile in Standardmaterialien hergestellt werden können, ist aufgrund der guten Materialeigenschaften für RM prädestiniert. In den ersten Anwendungsfeldern des SLM–Verfahrens standen die Herstellung von Werkzeugeinsätzen mit konturnaher Kühlung (Conformal Cooling) im Vordergrund, wobei diese Werkzeuge unter dem Begriff RM verstanden werden müssen, da die Werkzeuge direkt für die Endanwendung - den Spritzgussprozess - verwendet werden. Aktuelle Trends gehen jedoch in Richtung der Fertigung von Funktionsteilen z.B. für den Maschinenbau. Obwohl sich in der Fertigung komplexer Funktionsteile noch Probleme, z.B. mit in Bezug auf die generative Baurichtung überhängender Bauteilstrukturen ergeben, zeigen sich trotzdem erhebliche Vorteile eines RM mittels SLM. Neben klaren Vorteilen durch das mögliche Customizing von Bauteilen können bei kleineren Bauteilgrössen auch erhebliche Kostenvorteile erzielt werden. Allerdings zeigen die Grenzen der aktuellen Möglichkeiten, in welchen Bereichen das SLM-Verfahren weiterer Entwicklung bedarf. Themen wie Produktivität, die Problematik der nach wie vor notwendigen Supportstrukturen wie auch Qualitätssicherung müssen in den nächsten Jahren angegangen werden, wenn dieses Verfahren den Schritt hin zu einem etablierten Produktionsverfahren und damit zu breiterer Akzeptanz und Anwendung finden soll

SLM von Polylactiden zur Herstellung von resorbierbaren Implantaten

Rapid Manufacturing von individuellen Implantaten mittels Selective Laser Melting (SLM) wurde für metallische Standardwerkstoffe in der Medizintechnik (Titanlegierungen, Kobalt-Chrom-Legierungen, Stahl) realisiert. Dies sind permanente Implantate, die entweder dauerhaft im Körper verbleiben oder in einer zweiten Operation entfernt werden. Eine vom ILT mittels SLM hergestellte Hüftpfanne aus TiAl6V4 konnte bereits erfolgreich im Patienten implantiert werden. Die regenerative Therapie ist jedoch die klinisch bevorzugte Strategie. Das bedeutet, dass der Selbstheilungsprozess des menschlichen Körpers für die Heilung von großen Knochendefekten genutzt wird. Ein neuer Ansatz zur Implantatfertigung folgt dieser Strategie. Der SLM-Prozess wird für die Verarbeitung von bioresorbierbaren Werkstoffen entwickelt um individuelle Implantate zu fertigen, die im Körper abgebaut und durch körpereigenes Knochengewebe ersetzt werden. Diese Arbeit beschreibt die Qualifizierung des SLM Verfahrens für die Verarbeitung von einem Kompositmaterial aus Polylactid / β-Tricalciumphosphat (PDLLA/β-TCP).

Direkte generative Fertigung von Schmiedegesenken eröffnet neue Möglichkeiten

Umformwerkzeuge sind eine neue und bislang nicht erforschte Anwendung generativ gefertigter Werkzeuge. Der Vortrag präsentiert ein Fallbeispiel, bei dem ein typisches Schmiedeteil mit recht komplexer Geometrie erfolgreich unter Verwendung eines generativ gefertigten Schmiedegesenks hergestellt werden konnte. Die Marktanforderungen zur frühestmöglichen Verfügbarkeit echter Schmiedeteile werden dargestellt. Die gesamte Prozesskette von der 3D-CAD-Werkzeugkonstruktion über die Schmiedeprozesssimulation, das Laserstrahlschmelzen der Gesenkeinsätze und die Gesenkmontage bis hin zu den eigentlichen Schmiedeversuchen unter produktionsähnlichen Bedingungen wird dargestellt und mit konventioneller Schmiedegesenkkonstruktion und ‑fertigung verglichen. Die Vorteile und Besonderheiten der generativen Prozesskette werden herausgestellt. Die gefertigten Schmiedeteile werden hinsichtlich Formfüllung, Maßhaltigkeit und Gefüge mit konventionell geschmiedeten Teilen verglichen. Die Lieferzeit der generativ gefertigten Schmiedegesenke wird der von konventionell hergestellten gegenübergestellt, ebenso die Kosten, um die Vorteile des Einsatzes generativer Fertigung herauszustellen. Es werden Randbedingungen beschrieben, unter denen die generative Fertigung von Schmiedegesenken technisch und wirtschaftlich sinnvoll ist.