Effect of lactose solid-state on the aerosolization performance of drug-carrier mixtures

Lactose, in particular α-lactose monohydrate, is the most used carrier for inhalation. Its surface and solid-state properties are of paramount importance in determining drug aerosolization performance. However, these properties may be altered by processing, such as micronization, thus affecting the product performance and stability. The present research project focused on the study of the effect of lactose solid-state on the aerosolization performance of drug-carrier mixtures, giving particular attention to the impact of micronization on lactose physico-chemical properties. The formation of a fraction of hygroscopic anhydrous α-lactose, rather than amorphous lactose, as a consequence of the mechanical stress stemming from micronization was evidenced by 1H NMR, XRPD and DSC analyses performed on samples of micronized lactose. The development of a new DVS method capable to identify and quantify different forms of α-lactose (hygroscopic anhydrous, stable anhydrous and amorphous), even simultaneously present in the same sample, confirmed the results obtained with the above-mentioned techniques. The influence of lactose solid-state on drug respirability was then evaluated through the preparation and in vitro aerodynamic assessment of ternary and binary mixtures containing two different drugs. In particular, the use, as carriers, of anhydrous forms of α-lactose in place of the conventional α-lactose monohydrate resulted in significantly improved respirability in the case of salbutamol sulphate and poorer performance in the case of budesonide. In an attempt to rationalize the obtained results, IGC was selected as a tool to investigate possible variations in the surface energy of the studied lactose carriers and APIs. A direct correlation between the total surface free energy of lactose carriers and drug respirability was not found. However, salbutamol sulphate and budesonide exhibited different specific surface free energy, to which the difference in the aerosolization performance may be, at least in part, ascribed.

The secondary nucleation threshold and crystal growth of alpha-glucose monohydrate in aqueous solution

Investigation of the secondary nucleation threshold (SNT) of alpha-glucose monohydrate was conducted in aqueous solutions in agitated batch systems for the temperature range 10 to 40 degrees C. The width of the SNT decreased as the induction time increased and was found to be temperature independent when supersaturation was based on the absolute concentration driving force. Nonnucleating seeded batch bulk crystallizations of this sugar were performed isothermally in the same temperature range as the SNT experiments, and within the SNT region to avoid nucleation. The growth kinetics were found to be linearly dependent on the supersaturation of total glucose in the system when the mutarotation reaction is not rate limiting. The growth rate constant increases with increasing temperature and follows an Arrhenius relationship with an activation energy of 50 +/- 2 kJ/mol. alpha-Glucose monohydrate shows significant crystal growth rate dispersion (GRD). For the seeds used, the 95% range of growth rates was within a factor of 6 for seeds with a narrow particle size distribution, and 8 for seeds with a wider distribution that was used at 25 degrees C. The results will be used to model the significance of the mutarotation reaction on the overall crystallization rate of D-glucose in industrial crystallization.

Dry powder inhaler formulations-effect of polymer carrier size on the drug dispersion

Background The size of the carrier influences the aerosolization of drug from a dry powder inhaler (DPI) formulation. Currently, lactose monohydrate particles in a variety of sizes are preferably used in carrier based DPI formulations of various drugs; however, contradictory reports exist regarding the effect of the size of the carrier on the dispersion of drug. In this study we examined the influence of the intrinsic particle size of the polymeric carrier on the aerosolization of a model drug salbutamol sulphate (SS). Methods Four different sizes (20–150 lm) of polymer carriers were fabricated using solvent evaporation technique and the dispersion of SS particles from these carriers was measured by a Twin Stage Impinger (TSI). The size and morphological properties of polymer carriers were by laser diffraction and SEM, respectively. Results The FPF from these carriers was found to be increasing from 5.6% to 21.3% with increasing the carrier size. The FPF was found to be greater (21%) with the highest particle size of the carrier (150 lm). Conclusions The aerosolization of drug was dependent on the size of polymer carriers. The smaller size of the carrier resulted in lower FPF which was increased with increasing the carrier size. For a fixed mass of drug particles in a formulation, the mass of drug particles per unit area of carriers is higher in formulations containing the larger carriers, which leads to an increase in the dispersion of drug due to the increased mechanical forces occurred between the carriers and the device walls.

Characterization and evaluation of melibiose as novel excipient in tablet compaction

Lactose is probably the most used tablet excipient in the field of pharmacy. Although lactose is thoroughly characterized and available in many different forms there is a need to find a replacer for lactose as a filler/binder in tablet formulations because it has some downsides. Melibiose is a relatively unknown disaccharide that has not been thoroughly characterized and not previously used as an excipient in tablets. Structurally melibiose is close to lactose as it is also formed from the same two monosaccharides, glucose and galactose. Aim of this research is to characterize and to study physicochemical properties of melibiose. Also the potential of melibiose to be used as pharmaceutical tablet excipient, even as a substitute for lactose is evaluated. Current knowledge about fundamentals of tableting and methods for determinating of deformation behavior and tabletability are reviewed. In this research Raman spectroscopy, X-ray powder diffraction (XRPD), near-infrared spectroscopy (NIR) and Fourier-transform infrared spectroscopy (FT-IR) were used to study differences between two melibiose batches purchased from two suppliers. In NIR and FT-IR measurements no difference between materials could be observed. XPRD and Raman however found differences between the two melibiose batches. Also the effects of moisture content and heating to material properties were studied and moisture content of materials seems to cause some differences. Thermal analytical methods, differential scanning calorimetry (DSC) and thermogravimetry (TG) were used to study thermal behaviour of melibiose and difference between materials was found. Other melibiose batch contains residual water which evaporates at higher temperatures causing the differences in thermal behaviour. Scanning electron microscopy images were used to evaluate particle size, particle shape and morphology. Bulk, tapped and true densities and flow properties of melibiose was measured. Particle size of the melibiose batches are quite different resulting causing differences in the flowability. Instrumented tableting machine and compression simulator were used to evaluate tableting properties of melbiose compared to α-lactose monohydrate. Heckel analysis and strain-rate sensitivity index were used to determine deformation mechanism of melibiose monohydrate in relation to α–lactose monohydrate during compaction. Melibiose seems to have similar deformation behaviour than α-lactose monohydrate. Melibiose is most likely fragmenting material. Melibiose has better compactibility than α – lactose monohydrate as it produces tablets with higher tensile strength with similar compression pressures. More compression studies are however needed to confirm these results because limitations of this study.

Investigation of influence of process variables on mechanical strength, size and homogeneity of pharmaceutical granules produced by fluidised hot melt granulation

The overall aim of the project was to study the influence of process variables on the distribution of a model active pharmaceutical ingredient (API) during fluidised melt granulation of pharmaceutical granules with a view of optimising product characteristics. Granules were produced using common pharmaceutical excipients; lactose monohydrate using poly ethylene glycol (PEG1500) as a meltable binder. Methylene blue was used as a model API. Empirical models relating the process variables to the granules properties such as granule mean size, product homogeneity and granule strength were developed using the design of experiment approach. Fluidising air velocity and fluidising air temperature were shown to strongly influence the product properties. Optimisation studies showed that strong granules with homogeneous distribution of the active ingredient can be produced at high fluidising air velocity and at high fluidising air temperatures.

Drug Excipient Interaction Study with Polymorphic Forms of Tibolone

Powder mixtures (1:1) of tibolone polymorphic forms I (monoclinic) and II (triclinic) and excipients have been prepared and compacted. The samples were stored at 50 degrees C and 90% RH for one month and subsequently were evaluated using differential scanning calorimetry (DSC) and high-performance liquid chromatography (HPLC). The results indicate that during the compaction, the applied pressure reduced the chemical stability of tibolone in both polymorph forms. The triclinic form was more chemically unstable, both pure and in contact with excipients, than the monoclinic form. Lactose monohydrate was shown to reduce chemical degradation for both forms. Ascorbyl palmitate was shown to affect the tibolone stability differently depending on the polymorphic form used.

Effects of meloxicam administration on physiological and performance responses of transported feeder cattle

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Atenolol characterization in solid formulations available in Brazilian market

Atenolol is the most used drug in Brazil to hypertension treatment. Two crystal structures are known for this molecule: a racemic form (R,S)-atenolol and a pure form S-atenolol. The racemic form is found in commercial tablets. X-ray powder diffraction (XRD) is an adequate tool to study crystalline structures including drugs. Using the Rietveld Method with XRD data it is possible to quantify the crystalline structures existing in the raw material. Other methods like Le Bail and Pawley can be used to the profile fit and phases identification. For this work we analyzed three tablets of atenolol, two generics and the reference (materials were purchased from a drugstore at the city of Araraquara). These tablets were analyzed by Rietveld, Le Bail and Pawley methods. All tablets exhibited the racemic mixture API (R,S)-atenolol. Some crystalline excipients could be characterized: magnesium carbonate hydrate, lactose monohydrate and talc. The conclusion is that the three methods can be efficiently used to characterize the three atenolol tablets.

Utilização do meloxicam para reduzir respostas Inflamatórias em bovinos de corte transportados

Pós-graduação em Zootecnia - FMVZ

Método para controle da qualidade de medicamentos sólidos por difração de raios X

Pós-graduação em Química - IQ

Untersuchung der Adhäsionskräfte in interaktiven Pulvermischungen zur Inhalation und deren Veränderung in Abhängigkeit von der Dichtigkeit der Verpackung

Die Untersuchung der Adhäsionskräfte mit Colloid Probe Technik, einer Weiterentwicklung der Rasterkraftmikroskopie (Atomic Force Microscopy=AFM), an erzeugten Carrier- und Wirkstoffkristallen bei Laborbedingungen und unter Einfluss der Luftfeuchte zeigte, dass die Adhäsion von Tiotropiumbromid Monohydrat an Mannitol deutlich höher ist als an Lactose Monohydrat. Die Kohäsionskräfte des Wirkstoffes sind stärker als die Adhäsionskräfte an Carriermaterialien. Auf dieser Grundlage wurde die Hypothese aufgestellt, dass eine Mischung mit Mannitol als Carrier eine kleinere Feinpartikeldosis liefert als eine Mischung mit Lactose. Diese Theorie wurde an interaktiven Pulvermischungen unter Variation von verschiedenen Einflussfaktoren überprüft. Die binare und ternäre Lactose-basierte Mischung lieferte unabhängig vom Kapselmaterial (Gelatine- und Polyethylenkapsel) eine höhere Feinpartikeldosis als die entsprechenden Mannitol-basierten Formulierungen. Die ternäre Komponente bewirkte nur bei Mannitol-basierten Mischungen eine Verbesserung der Feinpartikeldosis. Die detaillierte Untersuchung der aerodynamischen Verteilung ternärer Mischungen zeigte, dass das Kapselmaterial nur unter dem Einfluss der Luftfeuchte und Permeabilität der Blisterverpackung die interpartikulären Wechselwirkungen beeinflusst. Mischungen mit Mannitol als Carrier lieferten unabhängig vom Kapselmaterial, von Luftfeuchte/Lagerungsbedingungen und Permeabilität der Blisterverpackung eine kleinere Feinpartikeldosis als Mischungen mit Lactose als Carrier. Die Carrierart, die Permeabilität der Blisterverpackung und die Luftfeuchte wurden als Haupteinflussfaktoren auf die aerodynamischen Eigenschaften identifiziert. Es konnte gezeigt werden, dass AFM einen wertvollen Beitrag zum Verständnis der interpartikulären Wechselwirkungen leistet und aufgrund prädiktiver Eigenschaften hilfreich in der Entwicklung inhalativer Darreichungs-formen sein kann.

Enzymatic production of oligosaccharides in centrifugal fields

The aims of this work have been to identify an enzymatic reaction system suitable to investigate and develop the high-speed centrifuge as a novel reaction system for performing such reactions. The production of galacto-oligosaccharides by the trans-galactosyl activity of the enzyme β-galactosidase on lactose monohydrate was identified as a model enzymatic system to elucidate the principles of this type of process. Galacto-oligosaccharides have attracted considerable commercial interest as food additives which have been shown to be beneficial to the health of the human gastrointestinal tract. The development of a single unit operation capable of controlling the biosynthesis of galacto-oligosaccharides whilst simultaneously separating the enzyme from the reaction products would reduce downstream processing costs. This thesis shows for the first time that by using a combination of (a) immobilised or insolubilised β-galactosidase , (b) a rate-zonal centrifugation technique, and (c) various applied centrifugal fields, that a high-speed centrifuge could be used to control the formation of galacto-oligosaccharides whilst removing the enzyme from the reaction products. By layering a suspension of insolubilised β-galactosidase on top of a lactose monohydrate density gradient and centrifuging, the applied centrifugal fields generated produced sedimentation of the enzyme particles through the substrate. The higher sedimentation rate of the enzyme compared to those of the reaction products allowed for separation to take place. Complete sedimentation, or pelleting of the enzyme permits the possible recovery and re-use. Insolubilisation of the enzyme allowed it to be sedimented through the substrate gradient using much lower applied centrifugal fields than that required to sediment free soluble enzyme and this allowed for less expensive centrifugation equipment to be used. Using free soluble and insolubilised β-galactosidase stirred-batch reactions were performed to investigate the kinetics of lactose monohydrate hydrolysis and galacto-oligosaccharide formation. Based on these results a preliminary mathematical model based on Michaelis-Menten kinetics was produced. It was found that the enzyme insolubilisation process using a chemical cross-linking agent did not affect the process of galacto-oligosaccharide formation. Centrifugation experiments were performed and it was found that by varying the applied centrifugal fields that the yield of galacto-oligosaccharides could be controlled. The higher the applied centrifugal fields the lower the yield of galacto-oligosaccharides. By increasing the applied centrifugal fields the 'contact time' between the sedimenting enzyme and the substrate was reduced, which produced lower yields. A novel technique involving pulsing the insolubilised enzyme through the substrate gradient was developed and this was found to produce higher yields of galacto-oligosaccharide compared to using a single enzyme loading equivalent to the total combined activity of the pulses. Comparison of the galacto-oligosaccharide yields between stirred-batch and centrifugation reactions showed that the applied centrifugal fields did not adversely affect the transgalactosyl activity of the insolubilised enzyme.

8-Ammonionaphthalene-2-sulfonate monohydrate : the zwitterionic hydrate of 1,7-Cleve's acid

The structure of 8-amino-2-naphthalenesulfonic acid monohydrate (1,7-Cleve's acid hydrate), C10H9NO3S.H2O, shows the presence of a sulfonate-aminium group zwitterion, both groups and the water molecule of solvation giving cyclic R3/3(8) intermolecular hydrogen-bonding interactions forming chains which extend down a axis of the unit cell. Additional peripheral associations, including weak aromatic ring pi-pi interactions [centroid-centroid distance 3.6299(15)A], result in a two-dimensional sheet structure.

Osteryoung square wave voltammetric determination of lactose in food samples by a derivative procedure

A method for determination of lactose in food samples by Osteryoung square wave voltammetry (OSWV) was developed. It was based on the nucleophilic addition reaction between lactose and aqua ammonia. The carbonyl group of lactose can be changed into imido group, and this increases the electrochemical activity in reduction and the sensitivity. The optimal condition for the nucleophilic addition reaction was investigated and it was found that in NH4Cl–NH3 buffer of pH 10.1, the linear range between the peak current and the concentration of lactose was 0.6–8.4 mg L−1, and the detection limits was 0.44 mg L−1. The proposed method was applied to the determination of lactose in food samples and satisfactory results were obtained.