XML-tekniikoihin perustuva ajurimalli LabView-pohjaiseen testausympäristöön

XML-muotoista tiedonesitystapaa hyödynnetään yhä enemmän esitettäessä rakenteellista tietoa. Tarkoituksena on antaa yleishyödyllinen ja uudelleenkäytettävä tapa jakaa yleistä tietoa erilaisten rajapintojen yli. XML-tekniikoita käytetään myös korjaamaan aiemmin tehdyissä sovellutuksissa esiintyneitä puutteita ja parantamaan niiden toimintaa. Tässä diplomityössä esitellään Telestelle LabView-pohjaiseen testaussovellusympäristöön suunniteltava ajuriuudistus. Työssä paranneltiin aiempaa ajurimallia soveltamalla siihen XML-tekniikoita hyödyntäviä toimintoja. Tarkoituksena oli vähentää testaussovelluskehityksessä vaadittavaa ohjelmointityötä korvaamalla sovelluksiin kovakoodatut ominaisuudet XML-pohjaisilla konfiguraatiotiedostoilla. Järjestelmän pohjana on yleiskäyttöinen ajuri, joka käyttää Telesten omaa EMS-protokollaa kommunikoinnissaan testattavien tuotteiden kanssa. Ajurimalli käyttää XML-pohjaisia konfiguraatiotiedostoja määrittelemään testattavien tuotteiden ominaisuuksia. XML-skeematiedostoilla esitetään ajurin käyttämän kommunikaatioprotokollan viestityypit ja niiden rakenteet. Työn tuloksena onnistuttiin luomaan uudenlainen XML-tekniikoita hyödyntävä ajurimalli. Yhteen yhteiseen ajuriin perustuva malli yhdenmukaistaa testaussovelluksien toteuttamista ja vähentää tarvittavaa ohjelmointityötä. Ajurin käyttöä helpotettiin toteuttamalla testaussovelluksien kehitysympäristöön erityinen editori, jolla voidaan helposti luoda ajuria käyttäviä toimintoja.

Effect of mechanical milling on the structural, magnetic and dielectric properties of coprecipitated ultrafine zinc ferrite

Nanosized ZnFe2O4 particles containing traces of a-Fe2O3 by intent were produced by low temperature chemical coprecipitation methods. These particles were subjected to high-energy ball milling. These were then characterised using X-ray diffraction, magnetisation and dielectric studies. The effect of milling on zinc ferrite particles have been studied with a view to ascertaining the anomalous behaviour of these materials in the nanoregime. X-ray diffraction and magnetisation studies carried out show that these particles are associated with strains and it is the surface effects that contribute to the magnetisation. Hematite percentage, probably due to decomposition of zinc ferrite, increases with milling. Dielectric behaviour of these particles is due to interfacial polarisation as proposed by Koops. Also the defects caused by the milling produce traps in the surface layer contributes to dielectric permittivity via spin polarised electron tunnelling between grains. The ionic mechanism is enhanced in dielectrics with the rise in temperature which results in the increase of dielectric permittivity with temperature.

View of Lithography Lab at the New York Trade School

Part of a lithography lab at the New York Trade School is depicted in this photograph. To the right sample prints are hung on a board, while other prints can be seen on the table, possibly drying. Black and white photograph.

Simultaneous nitrification, denitrification, and phosphorus removal in a lab-scale sequencing batch reactor

Simultaneous nitrification and denitrification (SND) via the nitrite pathway and anaerobic-anoxic-enhanced biological phosphorus removal (EBPR) are two processes that can significantly reduce the energy and COD demand for nitrogen and phosphorus removal. The combination of these two processes has the potential of achieving simultaneous nitrogen and phosphorus removal with a minimal requirement for COD. A lab-scale sequencing batch reactor (SBR) was operated in alternating anaerobic-aerobic mode with a low dissolved oxygen (DO) concentration (0.5 mg/L) during the aerobic period, and was demonstrated to accomplish nitrification, denitrification, and phosphorus removal. Under anaerobic conditions, COD was taken up and converted to poly-hydroxyalkanoates (PHAs), accompanied by phosphorus release. In the subsequent aerobic stage, PHA was oxidized and phosphorus was taken up to

Design state exploration applied to the development of a remote lab for projectile launch experiments

This paper describes the application of Design State Exploration techniques in the development of a remote lab for projectile motion experiments. The application was enabled by the existence of two independent teams: one composed of a series of internships that started first and another with two grantees that started a few months later. The paper presents evidence on how this approach provided gains in the development process conducted by the second team that benefited from design state exploration studies performed by the first team. This particular aspect is highlighted in relation to the work already presented in the 10th Remote Engineering and Virtual Instrumentation (REV) conference.

Academic effectiveness of VISIR remote lab in analog electronics

The effectiveness of VISIR is compared to other experimentation activities under the point of view presented by the professor Soysal in 2000. Advantages and limitations are discussed in terms of equipment availability, infrastructure cost, and contribution to various elements of experimental learning.

Testing oligopoly theory in the lab

Previous literature is reviewed to account for the existing experimental tests of standard oligopoly-theoretic models.

A Lab-in-a-briefcase for rapid prostate specific antigen (PSA) screening from whole blood

We present a new concept for rapid and fully portable Prostate Specific Antigen (PSA) measurement, termed “Lab-in-a-Briefcase”, which integrates an affordable microfluidic ELISA platform utilising a melt-extruded fluoropolymer Micro Capillary Film (MCF) containing 10 bore, 200 μm internal diameter capillaries, a disposable multi-syringe aspirator (MSA) plus a sample tray pre-loaded with all required immunoassay reagents, and a portable film scanner for colorimetric signal digital quantitation. Each MSA can perform 10 replicate microfluidic immunoassays on 8 samples, allowing 80measurements to be made in less than 15 minutes based on semi-automated operation and norequirement of additional fluid handling equipment. An assay was optimised for measurement of a clinically relevant range of PSA from 0.9 to 60.0 ng/ml in 15 minutes with CVs in the order of 5% based on intra-assay variability when read using a consumer flatbed film scanner. The PSA assay performance in the MSA remained robust in the presence of undiluted or 1:2 diluted human serum or whole blood, and the matrix effect could simply be overcome by extending sample incubation times. The PSA "Lab-in-a-briefcase" is particularly suited to a low-resource health setting where diagnostic labs and automated immunoassay systems are not accessible, by allowing PSA measurement outside the laboratory using affordable equipment.

Carpentry Lab

This shows a view of the Carpentry Lab at the New York Trade School. Students can be seen working on a number of different projects. Black and white photograph.

CMoS lab-on-a-chip devices for individual cell biology

The development of microlectronic lab-on-a-chip devices (LOACs) can now be pursued thanks to the continous advances in silicon technology. LOACs are miniaturized devices whose aim is to perform in a more efficient way specific chemical or biological analysis protocols which are usually carried out with traditional laboratory equipment. In this application area, CMOS technology has the potential to integrate LOAC functionalities for cell biology applications in single chips, e.g. sensors, actuators, signal conditioning and processing circuits. In this work, after a review of the state of the art, the development of a CMOS prototype chip for individual cell manipulation and detection based on dielectrophoresis will be presented. Issues related to the embedded optical and capacitive detection of cells will be discussed together with the main experimental results obtained in manipulation and detection of living cells and microparticles.

Cosmic-Lab: Optical companions to binary Millisecond Pulsars

Millisecond Pulsars (MSPs) are fast rotating, highly magnetized neutron stars. According to the "canonical recycling scenario", MSPs form in binary systems containing a neutron star which is spun up through mass accretion from the evolving companion. Therefore, the final stage consists of a binary made of a MSP and the core of the deeply peeled companion. In the last years, however an increasing number of systems deviating from these expectations has been discovered, thus strongly indicating that our understanding of MSPs is far to be complete. The identification of the optical companions to binary MSPs is crucial to constrain the formation and evolution of these objects. In dense environments such as Globular Clusters (GCs), it also allows us to get insights on the cluster internal dynamics. By using deep photometric data, acquired both from space and ground-based telescopes, we identified 5 new companions to MSPs. Three of them being located in GCs and two in the Galactic Field. The three new identifications in GCs increased by 50% the number of such objects known before this Thesis. They all are non-degenerate stars, at odds with the expectations of the "canonical recycling scenario". These results therefore suggest either that transitory phases should also be taken into account, or that dynamical processes, as exchange interactions, play a crucial role in the evolution of MSPs. We also performed a spectroscopic follow-up of the companion to PSRJ1740-5340A in the GC NGC 6397, confirming that it is a deeply peeled star descending from a ~0.8Msun progenitor. This nicely confirms the theoretical expectations about the formation and evolution of MSPs.